Get Fuses and bulbs Guide for Audi A5 4 Door First Generation (2007-2013)

Fuses and bulbs272

Fuses and bulbs

Fuses

Changing a fuse

If a fuse has blown it must be replaced.

– Identify the fuse for the failed component.

– Switch off the ignition and the component concerned.

– Remove the fuse box cover ⇒ fig. 253.

– Take the plastic clip from inside the fuse cover, fit it onto

the blown fuse, and pull the fuse out.

– Replace the blown fuse (which will have a melted metal

strip) with a new fuse of the same amp rating.

The various electrical circuits are protected by fuses. The fuse boxes

are located behind covers on the left and right sides of the dash

panel and in the compartment on the right side of the boot.

A plastic clip for removing the fuses is provided in the fuse cover on

the left side of the dash panel. There is also a sticker listing the fuses

in each of the fuse boxes in the dash panel.

Caution

Never attempt to “repair” a fuse or replace it by fitting a fuse with a

higher rating - risk of fire! It could also cause damage to other parts

of the electrical system.

Note

If a newly replaced fuse blows again after a short time, the electrical

system must be checked by a qualified workshop as soon as

possible.

Fuses on the driver's side

Some of the items listed are only fitted on certain models or are

optional extras.

Please note that the following list, while correct at the time of

printing, is subject to alterations. If discrepancies should occur,

please refer to the sticker on the inside of the fuse cover for the

correct information for your vehicle.

Fig. 253 Left side of

dash panel: Fuse cover

Fig. 254 Diagram of

fuse box (left-hand

drive vehicle)

document_0900452a8179700c.book Seite 272 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs 273

Controls Safety Driving tips General maintenance Self-help Technical data

The seats with electrical adjustment are protected by circuit

breakers. These reset automatically after a few seconds when the

overload has been corrected.

Fuse list

No. Electrical equipment amps

Fuse carrier (black)

1 Vacant

2 Clutch sensor 5

3 Garage door opener 5

4 Vacant

5 Air conditioner 5

6 Headlight range control (right) 5

7 Headlight range control (left) 5

8 Control unit 1 for vehicle's electrical system 5

9 Interior mirrors 5

10 Selector gate 5

11 Heated washer jets 5

12 Air conditioner 5

No. Electrical equipment amps

Fuse carrier (brown)

1 Vacant

2 Clutch sensor 5

3 Fuel pump (diesel/petrol) 20/25

4 Vacant

5 Control unit for vehicle's electrical system 30

6 Electronic stabilisation program 10

7 Horn 25

8 Electric window motor (left door) 30

9 Wiper motor 30

10 Electronic stabilisation program 25

11 Door control unit (driver's side) 15

12 Rain and light sensor 5

No. Electrical equipment amps

Fuse carrier (red)

1 Vacant

2 Vacant

3 Lumbar support 10

4 Vacant

5 Vacant

6 Control unit 1 for vehicle's electrical system 35

7 Control unit 1 for vehicle's electrical system 30

8 Control unit 1 for vehicle's electrical system 30

9 Tilting panorama roof 20

10 Control unit 1 for vehicle's electrical system 30

11 Vacant

12 Anti-theft alarm system 5

No. Electrical equipment amps

document_0900452a8179700c.book Seite 273 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs274

Fuses on the passenger's side

Some of the items listed are only fitted on certain models or are

optional extras.

Please note that the following list, while correct at the time of

printing, is subject to alterations. If discrepancies should occur,

please refer to the sticker on the inside of the fuse cover for the

correct information for your vehicle.

The seats with electrical adjustment are protected by circuit

breakers. These reset automatically after a few seconds when the

overload has been corrected.

Fuse list

No. Electrical equipment amps

Fuse carrier (black)

1 Vacant

2 Vacant

3 Vacant

4 Vacant

5 Steering column switch module 5

6 Switch for ASR, ESP and parking aid 5

Fig. 255 Diagram of

fuse box (left-hand

drive vehicle)

7 Diagnostic connector 5

8 Gateway (diagnostic interface for data bus) 5

9 Vacant

10 Vacant

11 Vacant

12 Vacant

No. Electrical equipment amps

Fuse carrier (brown)

1 CD drive 5

2 Switch module 5

3 MMI/Radio 10/20

4 Light switch 5

5 Control unit for instrument cluster 5

6 Ignition lock 5

7 Vacant

8 Air conditioner blower 40

9 Steering column lock 5

10 Air conditioner 10

11 Diagnostic connector 10

12 Steering column switch module 5

No. Electrical equipment amps

document_0900452a8179700c.book Seite 274 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs 275

Controls Safety Driving tips General maintenance Self-help Technical data

Fuse list for luggage compartment

– Remove the trim.

– Open the fuse cover.

Fuse list

No. Electrical equipment amps

Fuse carrier (black)

1 Vacant

2 Control unit for trailer 15

3 Control unit for trailer 20

4 Control unit for trailer 20

5 Electronic parking brake 5

6 Electronic suspension control 15

7 Electronic parking brake 30

8 Control unit 2 for vehicle's electrical system 30

9 Vacant

Fig. 256 Diagram of

fuse panel

10 Control unit 2 for vehicle's electrical system 30

11 Control unit 2 for vehicle's electrical system 20

12 Vacant

No. Electrical equipment amps

Fuse carrier (brown)

1 Electrical socket 15

2 Vacant

3 Radio/navigation 7.5

4 Control unit for digital sound system 30

5 MMI 5

6 Door control unit (driver's side) 30

7 Electronic parking brake 30

8 Seat heating, rear 30

9 Electric window (right) 30

10 Remote control receiver for auxiliary heating 5

11 Door control unit (passenger side) 15

12 Control unit for reversing camera 5

No. Electrical equipment amps

Fuse carrier (red)

1 Socket, centre console, rear 15

2 Socket, centre console, front 15

3 Socket, luggage compartment 15

No. Electrical equipment amps

document_0900452a8179700c.book Seite 275 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs276

Bulbs

Changing bulbs

Changing bulbs requires a certain degree of practical

skill.

You can change the following bulbs for exterior lights yourself:

• Halogen headlights: Bulb for dipped headlights

• Halogen headlights: Bulb for main beam headlights

• Halogen headlights: Bulb for side lights

• Xenon headlights*: Bulb for turn signals

• Bulb for fog light

• Bulbs for rear lights in boot lid

• Bulbs for rear lights in side panel

• Bulbs for number plate light

The following bulbs should only be changed by a qualified work-

shop:

• Halogen headlights: Bulb for turn signals

• Xenon headlights*: Light source for daytime running

lights/parking lights

• Bulb for headlights: Bi-xenon lights ⇒

• Light source for turn signal in exterior mirror housing

• Light source for high-level brake light

As a rule, you require a certain degree of practical skill to change

defective bulbs. This applies in particular to those bulbs which are

only accessible from the engine compartment.

If in doubt, we recommend that you have defective bulbs changed

by a qualified workshop or qualified mechanic.

If you do decide to change bulbs in the engine compartment your-

self, be aware of the safety risks involved ⇒ page 231 ⇒ .

Types of bulbs

You must only replace a bulb with a bulb of the same type. Informa-

tion regarding e.g. the wattage can be found on the base of the

bulb.

4 Cigarette lighter 15

5 Parking aid 5

Phone pre-installation without handsfree sys-

tem (VDA interface)

7 Vacant

8 Vacant

9 EPB switch (electro-mechanical parking brake) 5

10 Lane change assist feature 5

11 Seat heating, rear 5

12 Airbag 5

No. Electrical equipment amps

Front bulb (12 V) Version

Dipped-beam headlights (halogen) 55 W (H7)

Main beam headlights (halogen) 55 W (H7)

Front fog lights 55 W (H7)

Side lights (vehicles with halogen

headlights)

W 5 W

Front turn signals (vehicles with bi-

xenon headlights)

Hiper PY 24 W

Rear bulb (12 V) Version

Brake lights / tail lights P 21 W

Turn signals (rear) P 21 W

document_0900452a8179700c.book Seite 276 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs 277

Controls Safety Driving tips General maintenance Self-help Technical data

WARNING

• Take particular care when working on components in the

engine compartment if the engine is warm - risk of burns!

• Bulbs are sensitive to pressure. The glass can break when you

touch the bulb, causing injury.

• Incorrect handling of the high-voltage element of xenon gas-

discharge bulbs* can have potentially fatal consequences.

• When changing bulbs, please take care not to injure yourself on

sharp edges, in particular on the headlight housing.

Caution

• Always remove the ignition key before carrying out any work on

the electrical system - danger of short circuiting!

• Switch off the lights or parking lights before you change a bulb.

• Take good care to avoid damaging any components.

• Removing the lights in particular can lead to the paintwork

becoming damaged. This is another reason why we recommend

having the bulbs changed by a qualified workshop.

For the sake of the environment

Please ask your specialist retailer how to dispose of used bulbs in

the proper manner.

Note

Place the parts you have removed on a soft cloth so that they do not

become scratched.

• Please check at regular intervals that all lighting (especially the

exterior lighting) on your vehicle is functioning properly. This is not

only in the interest of your own safety, but also in that of all other

road users.

• Before changing a bulb, make sure you have the correct new

bulb.

• Do not touch the glass part of the bulb with your bare hands, use

a cloth or paper towel instead. Otherwise, the fingerprints left on

the glass will vaporise as a result of the heat generated by the bulb,

be deposited on the reflector and impair its surface.

Bulbs with a bayonet fastener

Bulbs with a bayonet fastener must be changed as follows:

Removing the bulb

– Lightly press the defective bulb into the bulb holder, then

turn it anti-clockwise and remove it.

– Do not touch the glass part of the new bulb with your

bare hands, use a cloth or paper towel instead.

Fitting the bulb

– Fit the new bulb, pressing it into the bulb holder, and turn

it clockwise as far as it will go.

– If necessary, use a cloth to remove any fingerprints from

the glass part of the bulb.

Reversing lights W 16 W

Rear fog light H 21 W

Number plate lights 5 W

document_0900452a8179700c.book Seite 277 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs278

Bulb holders with a bayonet fastener

In the case of bulb holders with a bayonet fastener please

proceed as follows:

Removing the bulb holder

– Turn the bulb holder in the direction of the arrow

⇒ fig. 257 as far as it will go and then take the bulb

holder out of the light unit.

Fitting the bulb holder

– Insert the bulb holder into the light unit, making sure you

keep the bulb holder straight, i.e. the rubber seal makes

even contact all around.

– Turn the bulb holder in the direction indicated by the

arrow ⇒ fig. 257 as far as it will go.

Changing bulbs for headlights

Removing and installing headlights

The description for removing the headlight refers to the left

headlight; in principle the same procedure applies to the

right headlight.

Removing

– Switch off the ignition and the lights.

– Open the bonnet.

Fig. 257 Diagram: Bulb

holder with a bayonet

fastener

Fig. 258 Trim panel:

Attachment points are

marked by arrows

Fig. 259 Headlight

unit: Attachment

points are marked by

arrows

document_0900452a8179700c.book Seite 278 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs 279

Controls Safety Driving tips General maintenance Self-help Technical data

– Take the screwdriver and the interchangeable Torx socket

out of the vehicle tool kit.

– Remove the screws ⇒ page 278, fig. 258 that secure the

trim panel to the lock carrier and detach the trim panel.

– Slacken the two screws that secure the headlight to the

lock carrier and the screw at the underside of the head-

light (this screw is located between the cover and the

rubber cap and should not be slackened more than ten

turns) ⇒ page 278, fig. 259.

– Carefully pull the headlight forward about 60 mm.

– Release and unplug the electrical connector.

– Carefully take the headlight out towards the front (swivel

it slightly if necessary).

Installing

– Perform all of the above steps in reverse sequence.

The headlight must be inserted in two guides (on the underside of

the headlight). This is the only way to ensure that the headlight is

installed in the correct position. To determine whether the headlight

is correctly installed, check that it is aligned flush with adjacent

body parts (such as the wing panel).

Do not interchange the securing screws.

Caution

Please take particular care not to damage or scratch the adjacent

parts of the body when removing or installing the headlights.

Applies to vehicles: with halogen main beam headlights

Removing bulb for main beam headlights

– Remove the headlight ⇒ page 278.

– Take off the rubber cap ⇒ fig. 260 ⇒ in “Changing

bulbs” on page 276.

– Press the connector in the direction of the arrow

⇒ fig. 261.

– Remove the connector together with the bulb from the

headlight housing.

– Disconnect the connector from the base of the bulb

⇒ in “Changing bulbs” on page 276.

Fig. 260 Headlight

unit: Rubber cap is

highlighted

Fig. 261 Bulb holder

for main beam head-

lights

document_0900452a8179700c.book Seite 279 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs280

Applies to vehicles: with halogen main beam headlights

Installing the bulb for the main beam

headlights

When installing a bulb, the lug on the base of the bulb

must be inserted into the appropriate mounting on the

bulb housing.

– Attach the new bulb to the connector ⇒ in “Changing

bulbs” on page 276.

– Insert the bulb carefully into the bulb housing. Start by

placing the base of the bulb directly behind one of the

retaining hooks so that the lug fits into the recess on the

bulb housing.

– Press the connector in the direction of the arrow

⇒ fig. 263 until the bulb engages.

– Check that the bulb is securely seated in the bulb

housing.

– Fit the rubber cap and install the headlight ⇒ page 278.

– Check whether the new bulb is working.

– Have the headlight settings checked.

Note

Ensure that the rubber cap is seated correctly so that no water can

enter the unit.

Applies to vehicles: with halogen dipped headlights

Removing bulb for dipped headlights

Fig. 262 Bulb with

connector: The lug on

the base of the bulb is

highlighted

Fig. 263 Fitting bulb

for main beam head-

lights

Fig. 264 Headlight

unit: Cover

document_0900452a8179700c.book Seite 280 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs 281

Controls Safety Driving tips General maintenance Self-help Technical data

– Remove the headlight ⇒ page 278.

– Swivel the retaining clip of the cover upwards.

– Take off the cover ⇒ page 280, fig. 264 ⇒ in

“Changing bulbs” on page 276.

– Press the connector in the direction of the arrow

⇒ fig. 265.

– Remove the connector together with the bulb from the

headlight housing.

– Disconnect the connector from the base of the bulb

⇒ in “Changing bulbs” on page 276.

Applies to vehicles: with halogen dipped headlights

Installing bulb for dipped headlights

When installing a bulb, the lug on the base of the bulb

must be inserted into the appropriate mounting on the

bulb housing.

– Attach the new bulb to the connector ⇒ in “Changing

bulbs” on page 276.

– Insert the bulb carefully into the bulb housing. Start by

placing the base of the bulb directly behind one of the

retaining hooks so that the lug fits into the recess on the

bulb housing.

Fig. 265 Bulb holder

for dipped headlights

Fig. 266 Bulb with

connector: The lug on

the base of the bulb is

highlighted

Fig. 267 Inserting bulb

for dipped headlights

document_0900452a8179700c.book Seite 281 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs282

– Press the connector in the direction of the arrow

⇒ page 281, fig. 267 until the bulb engages.

– Check that the bulb is securely seated in the bulb

housing.

– Fit the cover and swivel the retaining clip downwards.

– Install the headlight ⇒ page 278.

– Check whether the new bulb is working.

– Have the headlight settings checked.

Applies to vehicles: with xenon headlight bulbs

Changing bulb for turn signals

The bulb is secured in the bulb carrier with a bayonet

fastener.

– Remove the headlight ⇒ page 278.

– Take off the rubber cap (small cover) and remove the bulb

carrier.

– Lightly press the defective bulb into the bulb carrier, then

turn it anti-clockwise and remove it.

– Do not touch the glass part of the new bulb with your

bare hands, use a cloth or paper towel instead.

– Fit the new bulb, pressing it into the bulb carrier, and turn

it clockwise as far as it will go.

– If necessary, use a cloth to remove any fingerprints from

the glass part of the bulb.

– Insert the bulb carrier into the headlight.

Note

Ensure that the rubber cap is seated correctly so that no water can

enter the unit.

Applies to vehicles: with halogen dipped headlights

Changing bulb for side lights

Removing bulb for side lights

– Remove the headlight ⇒ page 278.

– Swivel the retaining clip of the cover upwards.

– Take off the cover ⇒ page 280, fig. 264 ⇒ page 280 ⇒

in “Changing bulbs” on page 276.

– Grasp the bulb holder by the handle ⇒ fig. 268 and pull it

out.

– Lightly press the defective bulb into the bulb carrier, then

turn it anti-clockwise and remove it.

Installing bulb for side lights

– Fit the new bulb, pressing it into the bulb holder and turn

it clockwise as far as it will go.

Fig. 268 Bulb holder

for side lights is high-

lighted

document_0900452a8179700c.book Seite 282 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs 283

Controls Safety Driving tips General maintenance Self-help Technical data

– Use a clean cloth to remove any fingerprints from the

glass part of the bulb.

– Insert the bulb carrier into the headlight.

– Fit the cover and swivel the retaining clip downwards.

– Install the headlight ⇒ page 278.

– Check whether the new bulb is working.

Changing bulb for front fog lights

Preparations

The description for changing the bulb refers to the left fog

light; in principle the same procedure applies to the right

fog light.

– Switch off the ignition and the lights.

– Detach the trim cover ⇒ fig. 269 (pull it carefully in the

direction of the arrow).

– Remove the two securing screws ⇒ fig. 270 and pull the

fog light unit out of the bumper.

– Unplug the electrical connector.

Caution

The trim cover is secured to the bumper by several retaining hooks.

Do not use force when removing the trim cover to avoid damaging

it.

Changing bulb

– Turn the bulb holder anti-clockwise ⇒ page 278 and take

it out of the fog light housing.

Fig. 269 Trim cover for

fog light

Fig. 270 Screws

securing fog light

Fig. 271 Front fog

light: Bulb holder is

highlighted

document_0900452a8179700c.book Seite 283 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs284

– Insert the new bulb holder and turn it clockwise as far as

the stop ⇒ page 278.

After changing the bulb re-install all parts in the reverse sequence

and check that the bulb is working.

Changing bulbs for rear lights in side

panel

Overview of rear lights

• Brake lights

• Turn signals

The following instructions for changing the bulb refer to the left side

of the vehicle. Follow the same procedure for changing the bulb on

the other side of the vehicle.

Removing rear light

To change the bulbs, you must remove the rear light.

Removing the light requires a certain degree of practical

skill.

– Check which of the bulbs is defective.

– Open the boot lid.

– Remove the side trim.

– Insert the screwdriver (from the tool kit) through the side

opening in the plastic screw ⇒ fig. 273.

Fig. 272 Rear lights in

side panel

Fig. 273 Luggage

compartment: Loca-

tion of retaining screw

for rear light

Fig. 274 Removing

rear light from side

panel

document_0900452a8179700c.book Seite 284 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs 285

Controls Safety Driving tips General maintenance Self-help Technical data

– Turn the screwdriver anti-clockwise to loosen the screw

and then carefully remove the screw.

– Gradually ease the light housing out of the rubber

mountings (positions ⇒ page 284, fig. 274 and ) by

pulling alternately in direction of arrows and . If

necessary use the tool for changing bulbs from your

vehicle's toolkit to carefully apply some pressure

between positions and ⇒ .

– Unplug the electrical connector.

– Change the defective bulb ⇒ page 285.

Caution

When removing or installing the rear light, take care not to cause

any damage.

• Removing the rear light in particular can lead to the paintwork or

rear light becoming damaged. This is another reason why we

recommend having the bulbs changed by a qualified workshop.

• NEVER use metal tools (e.g. a screwdriver) or sharp or pointed

plastic tools to lever out the rear light - risk of damaging the paint.

Note

Make sure you have a soft cloth ready to place under the glass on

the rear light, to avoid any scratches.

Changing bulbs

All bulbs can be changed easily after removing the rear

light.

The bulbs are secured with a bayonet fastener. The table

below gives an overview of the bulb positions.

– Remove the relevant bulb holder ⇒ page 278.

–Change the bulb ⇒ page 277.

– Install the bulb holder ⇒ page 278.

– Check whether the new bulb is working.

– Re-install the rear light ⇒ page 286.

Position of bulbs

Position: ⇒ fig. 275 Bulb function

A Turn signals

B Tail light and brake light

Fig. 275 Position of

bulbs in rear light.

Example: outer left rear

light

document_0900452a8179700c.book Seite 285 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs286

Installing rear light

The rear light is easy to re-install.

To re-install the rear light, follow the steps for removal in

reverse sequence.

– Plug in the electrical connector. Make sure you hear it

click into place.

– Insert the rear light into the rear light carrier ⇒ fig. 276.

– Press the rear light into the two rubber mountings as far

as it will go. The rear light must be flush with the body

contour.

– Use the screw to secure the rear light from the luggage

compartment.

– Make sure that all bulbs for the rear lights are working.

Caution

Take care when installing the rear light to make sure there is no

damage to the paintwork or any of its components.

Changing bulbs in boot lid

Rear lights in boot lid

• Rear fog light

• Reversing light

Before you begin working, please make yourself familiar with the

different bulb versions ⇒ page 276.

Removing bulb carrier

Fig. 276 Installing rear

light

Fig. 277 Rear lights in

boot lid

Fig. 278 Boot lid:

Opening the cover in

the boot lid

document_0900452a8179700c.book Seite 286 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs 287

Controls Safety Driving tips General maintenance Self-help Technical data

The description for changing the bulb refers to the left rear

light unit; in principle the same procedure applies to the

right rear light unit.

– Check which of the bulbs is defective.

– Open the boot lid.

– Take the screwdriver out of the vehicle tool kit.

– Using the flat-blade side of the reversible screwdriver

insert, carefully detach the cover cap ⇒ page 286,

fig. 278 -arrows-.

– Using the screwdriver, unscrew the nut ⇒ fig. 279 in

the anti-clockwise direction and remove the nut and the

retaining clip .

– Release the retaining tab and remove the bulb holder

from the light unit.

– Change the bulb ⇒ page 287.

Changing bulbs

All bulbs can be changed easily on the bulb carrier.

The bulbs are secured with a bayonet fastener. The table

below gives an overview of the bulb positions.

– Lightly press the defective bulb into the bulb carrier, then

turn it anti-clockwise and remove it.

– Fit the new bulb, pressing it into the bulb holder and turn

it clockwise as far as it will go.

– Use a cloth to remove any fingerprints from the glass

part of the bulb.

– Check whether the new bulb is working.

– Re-install the bulb carrier ⇒ page 288.

Position of bulbs

Fig. 279 Boot lid:

Removing bulb carrier

Pos. ⇒ fig. 280 Bulb function

A Reversing light

B Tail light and rear fog light

Fig. 280 Bulb carrier

for boot lid: Position of

the bulbs

document_0900452a8179700c.book Seite 287 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs288

Installing bulb carrier

The bulb carrier is easy to install.

– Insert the bulb carrier into the rear light. Make sure you

hear the retaining tab ⇒ fig. 281 click into place.

– Position the retaining clip so that the guide pins

are located in the recess on the retaining clip, and

tighten the nut .

– Fit the cover back in the interior trim so that it engages.

– Put the screwdriver back into the tool kit.

– Make sure that all bulbs for the rear lights are working.

Number plate light

Removing number plate light

– Take the screwdriver out of the vehicle tool kit

⇒ page 255.

– Insert the flat-blade side of the reversible screwdriver

insert into the slot on the number plate light ⇒ fig. 282.

– Using the screwdriver, start by pressing the number

plate light to the right -arrow 1- and then pull the number

plate light downwards from this position -arrow 2- and

out of the opening.

– Detach the number plate light.

Fig. 281 The retaining

clip for the bulb carrier

has a guide pin

Fig. 282 Boot lid:

Removing number

plate light

Fig. 283 Number plate

light: Retaining

element

document_0900452a8179700c.book Seite 288 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs 289

Controls Safety Driving tips General maintenance Self-help Technical data

Changing bulb

– Press the defective bulb out of the bulb holder and fit the

new bulb.

Installing number plate light

– First insert the side with the retaining element

⇒ page 288, fig. 283 and then carefully press the number

plate light into the opening.

– Check whether the new bulb is working.

document_0900452a8179700c.book Seite 289 Donnerstag, 22. März 2007 10:19 10

290

document_0900452a8179700c.book Seite 290 Donnerstag, 22. März 2007 10:19 10

Fuses and bulbs for Your Audi A5 4 Door First Generation (2007-2013)

Related Topics

Popular Owner Manuals

Latest Owner Manuals