2025-2026 Audi A5 4 Door Sitting correctly and safely -> Child safety seats User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Sitting correctly and safely -> Child safety seats for Your Audi A5 4 Door Third Generation (2025-2026)

Sitting correctly and safely  
You can also obtain useful and current informa-  
tion from the following sources:  
front passenger's seat, always make sure  
that PASSENGER AIR BAG OFF re-  
mains on while driving. If  
PASSENGER AIR BAG OFF does not  
turn on, remove the child safety seat and in-  
stall it again according to the child safety  
seat manufacturer instructions. If  
U.S. National Highway Traffic Safety Adminis-  
tration  
National SAFE KIDS Campaign  
PASSENGER AIR BAG OFF still does  
not turn on, the front passenger's seat must  
not be used. Drive to an authorized Audi  
dealer or authorized Audi Service Facility  
and have the airbag system inspected.  
Fluids, electronic devices, or mechanical  
damage on the front passenger's seat may  
cause the front passenger seat occupant de-  
tection to malfunction. The system may  
then incorrectly detect if the front passeng-  
er's seat is occupied. As a result, it could de-  
ploy the front passenger’s airbag incorrectly  
or fail to deploy it, which increases the risk  
of serious injury or death. Make sure that no  
wet objects (such as a wet hand towel) and  
no fluids come into contact with the front  
passenger's seat cushion. If the front pas-  
senger's seat becomes wet, dry it immedi-  
ately. Make sure no electronic devices (such  
as a laptop or a retrofitted seat heater) are  
on the front passenger's seat. Do not trans-  
port any objects on or under the front pas-  
senger's seat.  
SafetyBeltSafe U.S.A.  
Transport Canada Information Centre  
Audi Customer Experience Center  
contact.html  
WARNING  
To reduce the risk of serious injuries or death,  
children must always be secured in the vehicle  
with a child safety seat that is appropriate for  
their body size, weight, and age.  
Children ages 12 and under must be trans-  
ported using the appropriate child safety  
seat. Note differences in regulations be-  
tween states and countries.  
Child safety seats secured incorrectly in the  
vehicle may cause serious injuries or death  
in the event of an accident. Always secure  
the child safety seat according to the manu-  
facturer instructions.  
Seat covers or protective covers may prevent  
the advanced airbag system from correctly  
detecting child safety seats or persons in  
the front passenger's seat. You must not use  
seat covers or protective covers on the front  
passenger's seat that are not specifically ap-  
proved for use on Audi seats with an ad-  
vanced airbag system.  
Children or babies must not under any cir-  
cumstances be held on the lap of the driver  
or other passengers while driving.  
Do not secure more than one child in a child  
safety seat.  
Never allow a child to sit in a child safety  
seat unsupervised.  
Child safety seats  
Never allow children to ride unsecured in  
the vehicle or to stand or kneel on the seats  
while driving. In the event of an accident, a  
child could be propelled through the vehicle.  
This can result in serious injuries or death to  
the child and passengers.  
General information  
When installing and using child safety seats, fol-  
low the information in this Owner's Manual, the  
applicable state and federal regulations, and the  
manufacturer instructions for the child safety  
seat.  
If children sit in an incorrect seating position  
while driving, they have a higher risk of  
80  
Sitting correctly and safely  
injury during a sudden braking maneuver or  
accident. This especially applies to children  
in the front passenger's seat or children who  
have their head near the side airbag deploy-  
ment area, if the airbag system is deployed  
during an accident. This incorrect seating  
position can cause serious injuries or death.  
Make sure there is enough space in front of  
the child in the child safety seat. If necessa-  
ry, adjust the angle and position of the seat  
in front of the child safety seat.  
If you must use a forward-facing child safety  
seat on the front passenger's seat, move the  
seat as far back as possible so that it is as  
far as possible from the front passenger's  
airbag. Make sure the adjustment range is  
clear when doing this. A child in a child safe-  
ty seat on the front passenger's seat can re-  
ceive a severe impact if the front passeng-  
er's airbag deploys, which increases the risk  
of serious injury or death.  
Replace the child safety seat after an acci-  
dent because there could be damage that is  
not visible.  
The rear side of a forward-facing child safety  
seat should be positioned as close as possi-  
ble to the backrest on the vehicle seat. If the  
head restraints make it difficult to install a  
child safety seat, adjust or remove them if  
necessary ðpage 70. Reinstall the head re-  
straints immediately once the child safety  
seat has been removed.  
Even if a child is not sitting in the child safe-  
ty seat, the child safety seat must be se-  
cured. An unsecured child safety seat may  
be thrown through the vehicle interior dur-  
ing sudden braking maneuvers or an acci-  
dent.  
Always make sure that the backrest on the  
seat where the child safety seat is installed  
is securely locked in place and cannot move  
forward. Otherwise, the backrest where the  
child safety seat is secured could move for-  
ward in the event of an accident or other  
emergency situation.  
Correct positioning for children  
Always secure children in a child safety seat de-  
signed for the body size, weight, and age of the  
child.  
You can secure child safety seats in your vehicle  
using the lower LATCH anchors or the safety  
belts. You can also secure child safety seats to  
the top tether anchor. Depending on the child  
safety seat, it may also be necessary to secure it  
to the top tether anchor. In Canada, securing for-  
ward-facing child safety seats to the top tether  
anchors is required by law.  
NEVER use a rear-facing child safety seat on  
a seat with an ACTIVATED FRONT AIRBAG;  
this could cause DEATH or SERIOUS INJURIES  
to a CHILD.  
Always secure child safety seats on the  
rear seats. If exceptional circumstances re-  
quire the child safety seat to be placed on  
the front passenger's seat, then the front  
passenger's airbag must be deactivated.  
Always make sure that  
Always transport children in the rear seats  
Accident statistics show that children that are se-  
cured correctly in the rear seats are safer than in  
front seats. Always transport children in suitable  
child safety seats secured on the rear seats.  
PASSENGER AIR BAG OFF remains  
on while driving. If  
PASSENGER AIR BAG OFF does not  
turn on, remove the child safety seat and  
install it again according to the child safe-  
ty seat manufacturer instructions. If  
PASSENGER AIR BAG OFF still does  
not turn on, the front passenger's seat  
must not be used. Drive to an authorized  
Audi dealer or authorized Audi Service Fa-  
cility and have the airbag system inspect-  
ed.  
In exceptional circumstances: transporting  
children in the front passenger's seat  
If exceptional circumstances require the child  
safety seat to be placed on the front passenger's  
seat, then the front passenger's airbag must be  
deactivated. Please note the important informa-  
tion for this ðpage 78, Advanced airbag system.  
If you must secure a forward-facing child safety  
81  
Sitting correctly and safely  
seat, move the front passenger's seat as far back  
as possible so that it is as far as possible from the  
front passenger's airbag. Make sure the adjust-  
ment range is clear when doing this.  
All child safety seats are constructed so that  
they can be secured using the lap safety belt  
in the vehicle.  
Child safety seats with a load leg can only  
be secured to the outer rear seats and to the  
front passenger's seat.  
Only switch to a larger child safety seat when  
absolutely necessary  
Switch to a larger child safety seat only when ab-  
solutely necessary. Secure your child using a safe-  
ty belt without a child safety seat only if all of the  
following statements are true:  
Securing child safety seats to the lower  
LATCH anchors  
The child is large enough to sit upright in the  
seat  
The child is able to sit with their back resting  
completely on the seat backrest  
The child is able to sit with their knees angled  
over the edge of the seat surface  
The child is able to sit with both of their feet  
completely touching the floor in the footwell  
The lap portion of the safety belt lies flat and  
securely over the hip area and never over the  
stomach  
Fig. 72 Rear bench seat: lower LATCH anchors  
Observe the safety precautions ðpage 80.  
In the United States and Canada, child safety  
seats can be secured without safety belts using  
the LATCH system. LATCH stands for Lower An-  
chors and Tethers for Children. In Canada, similar  
systems are called UCRA, LUAS, or UAS.  
The shoulder portion of the safety belt lies flat  
and securely over the center of the shoulder  
and the chest, and never under the arm, behind  
the back, or over the neck or face.  
The child is able to maintain this seating posi-  
tion throughout the entire trip  
The lower LATCH anchors in your vehicle are lo-  
cated on the outer seats of the rear bench seat  
between the seat surface and the backrest. These  
seating locations each have two lower LATCH an-  
chors that can be used to secure a LATCH child  
safety seat. Marking points with a ðfig. 72 sym-  
bol are located on the covers for the lower LATCH  
anchors. You can locate the LATCH anchors using  
the marking points.  
Read and follow the important information and  
warnings regarding the correct use of safety  
belts ðpage 71.  
Tips  
Child safety seats can also be secured to  
seats with side airbags. In the event of an  
accident, children can also be protected by  
the side airbags if the child is correctly se-  
cured in a suitable child safety seat that is  
attached correctly.  
Activate the child safety lock ðpage 48.  
Remove the cover* from both lower LATCH an-  
chors.  
If you secure a child safety seat to the rear seat,  
secure any unused safety belts that are within  
The lower LATCH anchors as well as the  
safety belt may be required to correctly in-  
stall some child safety seats. Using both at  
the same time is permitted, provided that  
the fastening systems or safety belts do not  
impair those in an adjacent seating position.  
reach of the child ð  
in Securing child safety  
seats with a safety belt on page 83.  
Secure the child safety seat according to the  
child safety seat manufacturer instructions.  
82  
Sitting correctly and safely  
Pull on the child safety seat to check if both  
sides are engaged correctly in the LATCH an-  
chors.  
If possible, also secure the child safety seat to  
the respective top tether anchor in the vehicle  
ðpage 84.  
If the child safety seat is secured on the front  
passenger's seat, adjust the front passenger's  
seat backrest until it rests flat against the child  
safety seat. Also make sure that the upper safe-  
ty belt fixture is behind the child safety seat.  
If you secure a child safety seat on the rear  
seat, also secure it to the correct top tether an-  
chor if possible ðpage 84.  
WARNING  
The LATCH anchors in the vehicle are only de-  
signed for child safety seats with the LATCH  
system. To reduce the risk of serious injury or  
death, never secure other child restraint sys-  
tems, belts, or objects to the anchors.  
Activating the belt retractor lock  
If you secure a child safety seat using the vehicle  
safety belt, you must activate the belt retractor  
lock. Follow the child safety seat manufacturer  
instructions.  
Tips  
The belt retractor lock prevents the safety belt  
from becoming loose while driving, which could  
result in the child safety seat no longer being ad-  
equately secured.  
The LATCH anchors are designed for a total  
weight (child and child safety seat combined)  
up to 65 lbs (29 kg). If the total weight is  
greater than this, the child safety seat must  
be secured with the vehicle safety belt.  
Secure the child safety seat according to the  
child safety seat manufacturer instructions.  
While doing so, pull out the safety belt. Insert  
the safety belt into the belt latch that belongs  
to that seat until it audibly locks.  
Securing child safety seats with a safety  
belt  
Pull the upper belt out completely and then al-  
Observe the safety precautions ðpage 80. The  
front passenger’s seat is a dangerous location for  
a child, even with an advanced airbag system. If  
exceptional circumstances require the child safe-  
ty seat to be placed on the front passenger's  
seat, then the front passenger's airbag must be  
deactivated. Please note the important informa-  
tion for this ðpage 81, Correct positioning for  
children and ðpage 78, Advanced airbag sys-  
tem.  
low it to retract. You will hear a clicking sound  
while the belt is retracting. It will not be possi-  
ble to pull the safety belt out any farther.  
Push the child safety seat into the seat and al-  
low the belt to retract more.  
Make sure that the child safety seat cannot  
move more than 1 inch (2.5 cm).  
Deactivating the belt retractor lock  
Unbuckle the safety belt from the belt latch.  
Remove the child safety seat according to the  
Securing child safety seats  
manufacturer instructions.  
Allow the safety belt to retract completely. The  
belt retractor lock is deactivated.  
Activate the child safety lock ðpage 48.  
If you secure a child safety seat to the rear seat,  
secure any unused safety belts that are within  
reach of the child ð  
, ðpage 85.  
WARNING  
If you secure a child safety seat to the front  
passenger's seat, adjust the front passenger's  
seat to the highest position.  
Secure the child safety seat according to the  
child safety seat manufacturer instructions.  
If necessary, activate the belt retractor lock  
ðpage 83.  
A safety belt that is not locked by the belt  
retractor lock or a locking device cannot se-  
cure a child safety seat while driving or in  
the event of an accident, which increases  
the risk of death. Always make sure the belt  
retractor lock on the safety belt is activated  
83  
Sitting correctly and safely  
if the child safety seat manufacturer instruc-  
tions require it.  
To reduce the risk of death, never place a  
rear-facing child safety seat on the front  
passenger's seat when the front passenger's  
airbag is activated.  
For the child safety seat to offer the maxi-  
mum protection, it is especially important  
to route the vehicle safety belt correctly. Al-  
ways follow the instructions from the child  
safety seat manufacturer for routing the  
safety belt correctly. Incorrectly fastened  
safety belts can cause injuries, even during  
minor accidents.  
Additionally securing a child safety seat to  
the top tether anchor  
Fig. 74 Version  
1
rear shelf / Version  
2
rear backrest: se-  
curing the upper strap on the top tether anchor  
Observe the safety precautions ðpage 80.  
There is a top tether anchor behind every seat in  
the rear bench seat to additionally secure a child  
safety seat with an upper belt.  
Move the head restraint behind the child safety  
seat upward.  
Applies to: version 1: Fold the cover for the top  
tether anchor upward.  
Guide the upper belt on the child safety seat  
under the head restraint or along both sides of  
it and toward the rear (depending on the child  
safety seat model).  
Fasten the belt to the top tether anchor  
ðfig. 74. While doing this, make sure the belt  
is not twisted and is not running over any sharp  
edges.  
Fig. 73 Version  
top tether anchors for securing a child safety seat with an  
upper strap  
1
rear shelf / Version  
2
rear backrest:  
Secure the child safety seat according to the  
child safety seat manufacturer instructions.  
Pull the belt tightly so that the child safety seat  
rests at the top of the seat backrest.  
If necessary, move the head restraint behind  
the child safety seat downward.  
84  
Sitting correctly and safely  
tangled in them, which increases the risk of  
death. Always secure unused safety belts so  
that they are not within reach of children in  
child safety seats.  
WARNING  
The top tether anchors in the vehicle are only  
designed for child safety seats equipped with  
an upper strap. To reduce the risk of serious  
injury or death, never secure other child re-  
straint systems, belts, or objects to the an-  
chors.  
Securing unused safety belts on the rear  
bench seat  
Fig. 75 Rear bench seat: securing unused safety belts  
If a child safety seat is used on the rear bench  
seat, the child must not be able to reach any  
safety belts that are not being used. Secure safe-  
ty belts that are within reach of the child.  
If you secure a child safety seat to the LATCH  
anchors, fasten the safety belt on the seat  
where the child safety seat is installed using  
the seat's safety belt latch.  
Applies to: Sportback: If you secure a child safe-  
ty seat on one of the outer seats, fasten the  
safety belt for the center seat in its latch.  
Activate the belt retractor lock on the fastened  
safety belts. To do this, pull the upper belt out  
completely and then allow it to retract. You will  
hear a clicking sound while the belt is retract-  
ing. It will not be possible to pull the safety  
belt out any farther.  
Make sure the fastened safety belt does not  
block access to the LATCH anchors. Otherwise,  
it may not be possible to secure the child safety  
seat to the LATCH anchors correctly.  
WARNING  
A child in a child safety seat could play with  
the unused safety belts and then become en-  
85  

Related Topics

Popular Owner Manuals