2024-2026 Audi Q5 SUV Lights and vision -> Wipers (front wiper blades) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Lights and vision -> Wipers (front wiper blades) for Your Audi Q5 SUV Third Generation (2024-2026)

Lights and vision  
while. Single wipe also works when the vehicle is  
switched off.  
Wipers  
Using the windscreen wipers  
5 Wash/wipe . The number of wipe and extra-  
wipe cycles depends on how long you hold the  
wiper lever in position 5 .  
The windscreen is given an extra wipe a few sec-  
onds later to remove any dribbles of water (if the  
vehicle is moving). You can deactivate this func-  
tion by moving the wiper lever to position  
5
again within 10 seconds after the extra wipe. The  
extra-wipe function is activated again the next  
time you switch the vehicle on.  
Fig. 23 Wiper lever: Windscreen wipers  
The headlight washer system only operates when  
the dipped headlights are switched on. The head-  
lights are also automatically washed intermit-  
tently when you move the wiper lever to position  
5 .  
7 Rear wipe . The frequency of the rear wiper  
depends on the frequency of the windscreen wip-  
ers.  
If the windscreen wipers are on and in operation,  
the rear window wiper will also be switched on  
automatically when you engage reverse gear.  
Fig. 24 Wiper lever: Rear window wiper  
Move the windscreen wiper lever to the ap-  
8 Rear wash/wipe . The number of wiper cy-  
cles depends on how long you hold the wiper lev-  
er in position 8 . The reversing camera is also  
washed (depends on the vehicle’s equipment).  
propriate position:  
0 Wipers off  
1 Rain sensor/intermittent wipe. As long as the  
vehicle has been moving faster than approx.  
4 km/h at least once, the windscreen wipers will  
be activated automatically in the rain. The higher  
the sensitivity level for the rain sensor (i.e. the  
further switch 6 is moved to the right), the  
sooner the windscreen wipers react to moisture  
on the windscreen. You can deactivate the rain  
sensor mode in the Car menu ðpage 25 (this will  
activate the intermittent wipe mode). In inter-  
mittent wipe mode, you can adjust the interval  
with switch 6 .  
WARNING  
The rain sensor is only intended to assist the  
driver. The driver is still obliged to manually  
operate the windscreen wipers as required  
depending on visibility.  
Do not use water-repellent coatings on the  
windscreen. In bad visibility conditions such  
as light rain, low sun or when driving at  
night these coatings can cause increased  
dazzle, which is a serious safety hazard.  
Such coatings can also cause the wiper  
blades to judder.  
2 Slow wipe  
3 Fast wipe  
CAUTION  
4 Single wipe. If you hold the wiper lever in this  
position, the wipers will switch from slow contin-  
uous wiping to fast continuous wiping after a  
In icy conditions, check that the wiper  
blades are not frozen to the windscreen. If  
the wiper blades are frozen to the  
62  
Lights and vision  
Changing wiper blades  
windscreen when you switch on the wind-  
screen wipers, this could damage the wiper  
blades.  
Important: The wipers must be in the wiper  
change position.  
Switch the wipers off (wiper lever in position  
0 ) before you use an automatic car wash.  
This will avoid inadvertent triggering of the  
wipers and possible damage to the wiper  
system.  
Lift the wiper arm away from the glass.  
Keep hold of the wiper blade.  
Press the release button 1 on the wiper blade.  
Pull the wiper blade out of the mounting on the  
wiper arm 2 .  
Fit the new wiper blade into the mounting on  
Cleaning/changing the windscreen wiper  
blades  
the wiper arm. You should hear it engage.  
Fold the wiper arm back down onto the wind-  
screen.  
Switch off the wiper change function.  
WARNING  
Old or dirty wiper blades can impair the driv-  
er's view – risk of accident! Clean the wiper  
blades if they become dirty. Change the wiper  
blades once or twice a year. You should also  
change the wiper blades if they are no longer  
able to provide a clear view that is safe for  
driving, e.g. if the wiper blades become dam-  
aged.  
Fig. 25 Windscreen wipers: Changing wiper blades  
Activating the wiper change position  
Important: The bonnet must be closed.  
CAUTION  
Switch the vehicle off, move the windscreen  
The wipers must be in the wiper change po-  
sition before they are lifted off the wind-  
screen! Otherwise the wiper motor or the  
paintwork on the bonnet may be damaged.  
Never move your vehicle or operate the  
windscreen wiper lever while the wiper arms  
are off the glass in a raised position. The  
wipers will otherwise automatically return  
to their park position and may damage the  
bonnet and windscreen.  
wiper lever to position 4 ðpage 62, Fig. 23  
and hold it there until the wipers move into the  
wiper change position.  
To move the windscreen wipers back to their  
original position, switch the vehicle on and hold  
the windscreen wiper lever in position 4 until  
the wipers have returned to their original posi-  
tion, or drive faster than 12 km/h.  
You can also switch the wiper change position  
on/off on the centre display:  
Switch the windscreen wipers off (position  
ðpage 62, Fig. 23).  
0
Select: > Car > More > Wiper change posi-  
tion.  
Cleaning wiper blades  
Important: The wipers must be in the wiper  
change position.  
Lift the wiper arm away from the glass.  
Notes on cleaning ðtable on page 261.  
63  
Lights and vision  
If a fault persists, drive to a qualified workshop  
soon and have it rectified.  
Cleaning/changing the rear wiper blade  
Fig. 26 Rear window wiper: Attaching the wiper blade  
Cleaning the wiper blade  
Lift the rear wiper arm away from the glass.  
Notes on cleaning ðtable on page 261.  
Taking off the wiper blade  
Lift the rear wiper arm away from the glass.  
Pull the wiper blade out of the retainer.  
Fitting the wiper blade  
Press the mounting on the wiper blade into the  
retainer.  
Fold the wiper arm back down onto the rear  
window.  
WARNING  
Old or dirty wiper blades can impair the driv-  
er's view – risk of accident! Clean the wiper  
blades if they become dirty. Change the wiper  
blades once or twice a year. You should also  
change the wiper blades if they are no longer  
able to provide a clear view that is safe for  
driving, e.g. if the wiper blades become dam-  
aged.  
Driver messages about the wipers  
If  
is displayed in the event of a fault, the wip-  
er functions are unavailable or restricted.  
A driver message indicating the cause and possi-  
ble remedy may appear for some of the displays.  
To display the driver messages again, open the  
notification centre on the centre display. Try  
switching the wipers on later or after the vehicle  
is next switched on.  
64  

Related Topics

Popular Owner Manuals