Get Lights and vision Guide for Audi S Q5 SUV Third Generation (2025-2026)

Opening and closing

Programming

Applies to: vehicles with garage door opener

Tips

– If you sell your vehicle, reset all settings to

the factory default settings ðpage 243.

– The system complies with United States FCC

regulations and ISED regulations

ðpage 322.

You can program both fixed code and rolling code

systems in the MMI using the procedure that is

described.

Requirement: the ignition must be turned on.

If programming has been started, the  symbol

on the rearview mirror will flash orange.

Tips

Before you program your system to the ga-

rage door opener, first check the compatibili-

ty:

Programming the system

Applies to: MMI

– Ask an authorized Audi dealer or authorized

Audi Service Facility or check at

. You can also find more infor-

mation about HomeLink there.

Requirement: the hand-held transmitter must be

present and the vehicle must be within range of

the system (such as the garage door) that you

would like to program.

– You can display information about Home-

Link (compatibility level/status/country

code/HomeLink generation) in the MMI:

– Select on the home screen: VEHICLE > Set-

tings & Service > Garage opener > .

►

If you would like to program a system, select on

the home screen: VEHICLE > Settings & Service

> Garage opener. Press the desired button

(1-3). Follow the instructions in the MMI. Or

►

Press the corresponding button in the garage

door opener on the rearview mirror. Follow the

instructions in the MMI.

If you would like to reprogram systems that are

Operation

Applies to: vehicles with garage door opener

►

already programmed, select on the home

screen: VEHICLE > Settings & Service > Garage

opener. Press the button you would like to pro-

gram (1-3) with the opener system. Follow the

instructions in the MMI.

With some systems, the garage door opener will

be available immediately after programming.

With other systems, the garage door opener

must also be synchronized. In this case, the 

symbol on the rearview mirror will flash white

quickly.

Fig. 41 Rearview mirror: buttons for the garage door open-

er

Requirements: the remote control transmitter

must be programmed ðpage 50, Program-

ming, the vehicle must be within range of the

system, and the ignition must be turned on.

1)

Synchronizing

Requirement: the hand-held transmitter must al-

ready be programmed and the vehicle must be

within range of the system (such as the garage

door).

To open or close the system (such as the garage

door), press the corresponding button on the

rearview mirror.

If the system synchronization is performed di-

rectly after the programming procedure, follow

the instructions on the MMI.

If the signal was transmitted successfully, the 



symbol on the rearview mirror will flash white.

1)

Only applies to rolling code systems

50

Opening and closing

If you would like to sync at a later time:

►

Applies to: MMI: Select on the home screen:

VEHICLE > Settings & Service > Garage opener.

►

Press the desired button (1-3) that you would

like to synchronize and then press Sync.

►

Follow the instructions in the MMI.

Deleting programmed systems

Opener systems that are programmed can be de-

leted individually.

►

Applies to: MMI: Select on the home screen:

VEHICLE > Settings & Service > Garage opener.

►

Press the button (1-3) with the programming

you would like to delete and press Delete.

Tips

– Make sure the batteries in the hand-held

transmitter are charged before starting the

programming process.

– The programming process may take up to

30 seconds. It may be necessary for the

hand-held transmitter to be pressed again

in the meantime.

– The garage door opener may need to be

synchronized with the system after pro-

gramming. Follow the manufacturer's in-

structions for doing this.

Tips

In some cases, the system may need to be

programmed in a different mode (“D mode”).

– Turn on the ignition.

– Applies to: MMI: Select on the home screen:

VEHICLE > Settings & Service > Garage

opener.

– Press and hold the desired button (1-3).

– Select Yes, in D mode and follow the in-

structions on the MMI.

51

Lights and vision

3 Rear fog lights¹⁾

Applies to: vehicles with rear fog lights

Lights and vision

Exterior lighting

Turning the lights on or off

Requirement: the light switch must be in the AU-

TO or  position.

To reduce glare for traffic behind your vehicle,

the rear fog lights should only be turned on in ac-

cordance with the legal regulations in the coun-

try where you are operating the vehicle.

Automatic headlight range control

Your vehicle is equipped with automatic head-

light range control. It reduces glare for oncoming

traffic if the vehicle load changes. The headlight

range adjusts automatically.

Fig. 42 Instrument panel: light switch with buttons

Audi adaptive light

Applies to: vehicles with Audi adaptive light

1 Light switch 

Turn the light switch 1 to the corresponding po-

sition when the ignition is turned on. The 

symbol and the selected position will turn on (ex-

cept position O).

Audi adaptive light provides better visibility when

driving in the dark. The lights are adapted to the

road conditions based on speed, such as when

driving on expressways, rural roads, at intersec-

tions, and around curves. The adaptive lights only

function when the light switch is in the AUTO po-

sition and the all-weather lights are turned off.

O - The daytime running lights will automatically

turn on. In vehicles for some markets, you can

turn the automatic daytime running lights on and

off in the MMI.

WARNING

AUTO - The headlights will automatically adapt to

the surrounding brightness.

– Observe the safety precautions and note the

limitations of the assist systems, sensors,

and cameras ðpage 139 to ðpage 142.

– Automatic headlights are only intended to

assist the driver. The driver is still responsi-

ble for controlling the headlights and may

need to turn them on or off manually de-

pending on light and visibility conditions.

For example, fog cannot be detected by the

light sensors. So always turn on the low

beams  under these weather conditions

and when driving in the dark.

 – Parking lights

 – Low beam headlights

When the low beam headlights or parking lights





are turned on, the corresponding

or

indi-

cator light will turn on depending on vehicle

equipment.

2 All-weather lights 

Requirement: the light switch must be in the AU-

TO or  position.

Tips

The headlights automatically adjust so that there

will be less glare, for example when the road sur-

face is wet.

– If the vehicle battery has been discharging

for a while, the parking light may turn off

automatically. Avoid using the parking

lights for several hours.



1)

Depending on the country, two rear fog lights may be in-

stalled.

52

Lights and vision

High beams  and headlight flasher

– When using lighting equipment, the driver

is responsible for adhering to any local ap-

plicable regulations while driving and when

parking the vehicle.

►

Move the lever to the corresponding position:

3 High beams on (vehicles with High beam as-

sistant* ðpage 53)

– Only the front headlights turn on when the

daytime running lights are turned on. In

vehicles in certain markets, the tail lights

will also turn on.

4 High beams off or headlight flasher

The  indicator light in the instrument cluster

will turn on.

– In cool or damp weather, the inside of the

headlights, turn signals, and tail lights can

fog over due to the temperature difference

between the inside and outside. They will

clear shortly after turning them on. This

does not affect the service life of the light-

ing.

WARNING

High beams can cause glare for other persons,

which increases the risk of an accident. For

this reason, only use the high beams or the

headlight flasher when they will not create

glare for others.

Turn signal and high beam lever

High beam assistant

Applies to: vehicles with high beam assistant

The high beam assistant automatically turns the

high beams on or off depending on environmen-

tal factors.

A camera on the rearview mirror mount can de-

tect light sources from other road users. The high

beams turn on or off automatically depending on

the position of vehicles traveling ahead and on-

coming vehicles, the vehicle speed as well as oth-

er environmental factors and traffic conditions.

Fig. 43 Lever: turning the light functions on or off

The lever operates the turn signals, the high

beams and the headlight flasher.

Activating the high beam assistant 

Requirement: the light switch must be in the AU-

TO position and the high beam assistant must be

turned on in the MMI ðpage 54.

Turn signals  

The turn signal will activate when you move the

lever into a turn signal position while the ignition

is on. The respective  or  indicator light will

flash. The turn signal blinks three times if you

tap the lever (convenience turn signal).

►

To activate the high beam assistant, tap the

lever forward 3 ðpage 53, fig. 43. The  in-

dicator light will appear in the instrument clus-

ter display and the high beams will turn on or

off automatically. The  indicator light will

turn on if the high beams are turned on.

1 Right turn signal

2 Left turn signal

If an indicator light blinks twice as fast as usual,

a turn signal bulb has failed. Carefully drive to an

authorized Audi dealer or authorized Audi Service

Facility immediately to have the malfunction cor-

rected.

Activating and deactivating the high beam

head lights manually

If the high beams did not turn on or off as expect-

ed, you may turn them on or off manually in-

stead:



The  symbol does not have any function as-

signed to it in vehicles in certain countries.

53

Lights and vision

►

To activate the high beams manually, tap the

lever forward 3 ðpage 53, fig. 43. The  in-

dicator light will turn on.

Activation time - You can adjust if the headlights

turn on Early, Medium, or Late based on the sen-

sitivity of the light sensor.

►

To deactivate the high beams manually, pull

High beam assistant - You can turn the high

beam assistant on or off.

the lever back 4 ðpage 53, fig. 43. The high

beam assistant is deactivated.

Entry/exit lighting

Operating the headlight flasher

The Entry/exit lighting illuminates the area

around the vehicle when the vehicle is unlocked

or when the driver’s door is opened while the ig-

nition is off. The entry/exit lighting works when it

is dark and the light switch is in the AUTO posi-

tion. The daytime running lights turn on auto-

matically each time the vehicle is unlocked, re-

gardless of how bright it is outside the vehicle.

►

To operate the headlight flashers, pull the lever

back 4 ðpage 53, fig. 43. If the high beam

headlights are not turned on, the high beam as-

sistant will remain activated.

WARNING

– Observe the safety precautions and note the

limitations of the assist systems, sensors,

and cameras ðpage 139 to ðpage 142.

– The high beam assistant is only intended to

assist the driver. The driver is always respon-

sible for controlling the high beam head-

lights and adjusting them based on the

lighting and visibility conditions.

Daytime running lights

USA models: The daytime running lights can be

turned on or off.

Canada models: This function cannot be turned

off. They activate automatically each time the ig-

nition is turned on.

– High beams can cause glare for other per-

sons, which increases the risk of an accident.

For this reason, only use the high beams or

the headlight flasher when they will not cre-

ate glare for others.

Emergency flashers

Tips

Adhere to any local applicable regulations

when using the lighting equipment, for exam-

ple in regard to reducing glare for other road

users. The driver is always responsible for ad-

hering to the regulations applicable in the

country where the vehicle is being operated.

Fig. 44 Center console: emergency flashers

The emergency flashers help to make other road

users aware of your vehicle in dangerous situa-

tions.

Adjusting the exterior lighting

The following settings depend on the vehicle

equipment.

►

Press the  button 1 to turn the emergency

►

Applies to: MMI: Select on the home screen:

flashers on or off.

VEHICLE > Light & Visibility > Exterior light-

ing.

When the emergency flashers are turned on, the

 and  indicator lights will flash at the same

time.

Automatic headlights

You can adjust the following settings in the Auto-

matic headlights menu:

You can indicate a lane change or a turn when the

emergency flashers are on by using the turn



54

Lights and vision

signal lever. The emergency flashers will stop

temporarily.

 High beam assistant: malfunction! See own-

er's manual

The emergency flashers also work when the igni-

tion is turned off.

You can still turn the high beams on or off man-

ually. Drive immediately to an authorized Audi

dealer or authorized Audi Service Facility to have

the malfunction corrected.

Tips

You should turn the emergency flashers on if:

– You are the last vehicle in a traffic jam so

that all other vehicles approaching from be-

hind can see your vehicle

 High beam assistant: currently unavailable.

Camera view limited due to environmental con-

ditions

This message appears if the camera's visual field

is blocked. The system will turn itself off. Try

turning the systems on later.

– Your vehicle has broken down or you are

having an emergency

– Your vehicle is being towed or if you are

towing another vehicle



Automatic headlights: malfunction! See

owner's manual

Messages

The light/rain sensor is malfunctioning. In the

AUTO light switch position, the low beams re-

main turned on at all times for safety reasons.

Drive immediately to an authorized Audi dealer

or authorized Audi Service Facility to have the

malfunction corrected.

The following messages may appear, depending

on the vehicle equipment:

If the  indicator light turns on, a bulb has

failed. The displayed message indicates the cause

and possible solutions. If one of the messages re-

mains on, drive immediately to an authorized

Audi dealer or authorized Audi Service Facility to

have the malfunction corrected.

Interior lighting

Front interior lighting

 Audi adaptive light: malfunction! See own-

er's manual

Adaptive light is not working. The headlights still

function. Drive immediately to an authorized

Audi dealer or authorized Audi Service Facility to

have the malfunction corrected.

 Headlight range control: malfunction! See

owner's manual

Fig. 45 Headliner: front interior lighting

There is a malfunction in the headlight range

control system, which may cause glare for other

road users. Drive to an authorized Audi dealer or

authorized Audi Service Facility immediately to

have the malfunction corrected.

Interior lighting buttons

 – Interior lighting on/off

 – Door contact switch on/off. The interior light-

OLED

OLED tail light: malfunction! Switched off

ing is controlled automatically.

permanently. See owner's manual

Touch-sensitive reading lights

Drive immediately to an authorized Audi dealer

or authorized Audi Service Facility to have the

malfunction corrected.

►

To turn a reading light on or off, touch the sur-

face 1 briefly.

To activate the manual dimming function,

►

touch the surface 1 when the light is turned



55

Lights and vision

off and keep touching it until the desired

brightness is reached.

The following settings depend on the vehicle

equipment.

►

Applies to MMI: Select on the home screen: VE-

Rear interior lighting

HICLE > Light & Visibility > Interior lighting.

You can choose from various color profiles, such

as Maritime.

Additional settings and profiles:

– Brightness: you can adjust the brightness for

all of the interior lighting.

– Individual: you can adjust the brightness and

color of the interior lighting separately for the

line and surface lighting.

Fig. 46 Headliner: reading lights, version 1

– Audi drive select: the line and surface lighting

color changes depending on the selected drive

select mode.

Tips

Depending on vehicle equipment, when the

drive select* function is turned on, the color

of the contour and surface lighting may brief-

ly change to red or blue when the interior

temperature is manually increased or de-

creased.

Fig. 47 Headliner: reading lights, version 2

Reading lights

Display brightness

►

Version 1: to turn a reading light on or off,

You can set the instrument and display illumina-

tion. The settings depend on the vehicle equip-

ment.

press the  button 1 .

To activate the manual dimming function*,

touch the surface while the light is turned off

►

Applies to MMI: select on the home screen:



1 and keep touching it until the desired

SETTINGS > Display & Brightness.

brightness is reached.

►

Version 2 (touch-sensitive reading lights with

manual dimming function*): to turn a reading

– Cockpit dimming

– Head-up display

– MMI

light on or off, briefly touch the surface

2

ðfig. 47.

– Audi virtual cockpit

To activate the manual dimming function,

touch the surface 2 when the light is turned

off and keep touching it until the desired

brightness is reached.

Interior lighting

Applies to: vehicles with interior lighting

The ambient lighting turns on when the ignition

is turned on. The O light switch position deacti-

vates the interior lighting.

56

Lights and vision

0 – Deactivates all adjustment functions.

Instrument illumination

 /  – Selects the left or right exterior mirror.

To adjust the mirror glass in a mirror, press the

knob in the desired direction.

 – Heats the mirror glass depending on the

outside temperature.

 – Folds the exterior mirrors in*. To fold the

mirrors out, turn the knob to one of the other po-

sitions. In the MMI, you can select if the mirrors

fold in automatically when you lock the vehicle

ðpage 36.

Fig. 48 Light switch: instrument illumination

 – You can adjust the background brightness of

the instruments and display illumination.

Front passenger's exterior mirror tilt

function*

►

Press the knob 1 to release it.

Turn the knob toward "-" or "+" to reduce or in-

Requirement: the knob must be in the position

for the front passenger’s exterior mirror.

►

crease the brightness.

Press the knob again to return it to its original

position.

The mirror surfaces tilt slightly when reverse

gear is selected to provide a better view, for ex-

ample of the edge of the curb.

►

You can adjust the mirror surface by turning the

knob in the desired direction.

Tips

Depending on vehicle equipment, the instru-

ment illumination (needles and gauges) may

turn on when the lights are off and the igni-

tion is turned on. The illumination for the

gauges reduces automatically and eventually

turns off as brightness outside increases. This

function reminds the driver to turn the low

beams on at the appropriate time.

The mirror moves from the reversing position

back to the original position:

– When you turn off the ignition

– When you drive forward at speeds faster than 9

mph (15 km/h).

– When the knob is no longer in the position for

the front passenger exterior mirror

Vision

WARNING

Curved mirror surfaces (for example convex)

enlarge the field of vision. However, they

make objects in the mirror appear smaller and

farther away. When using these mirrors to es-

timate your distance to vehicles behind you

when changing lanes, you could estimate in-

correctly, which increases the risk of an acci-

dent.

Adjusting exterior mirrors

Note

– Applies to: vehicles with power folding exte-

rior mirrors: If the mirror housing was

Fig. 49 Driver's door: knob for the exterior mirrors

moved by outside forces (such as an impact

when maneuvering), you must use the pow-

er folding function to fold the mirror all the

►

Turn the knob in the driver's door to the desired

position:



57

Lights and vision

way out. The mirrors will make a loud noise

when they latch into place. The mirror hous-

ing must not be moved back into place by

hand because this could impair the function

of the mirror mechanism.

– If electrolyte fluid comes into contact with

the eyes, flush them thoroughly with plenty

of clean water for at least 15 minutes and

then seek medical attention.

– If electrolyte fluid comes into contact with

the skin, flush the affected area with clean

water for at least 15 minutes, and then

clean with soap and water and seek medical

attention. Clean affected clothing and shoes

thoroughly before wearing again.

– Applies to: vehicles without power folding

exterior mirrors: If the mirror housing was

moved by outside forces (such as an impact

when maneuvering), you must move it back

into place by hand.

– If you wash the vehicle in an automatic car

wash, you must fold the exterior mirrors in

to reduce the risk of damage to the mirrors.

Never fold power folding exterior mirrors*

by hand. Only fold them in and out using

the power controls.

– If the fluid was swallowed and the person is

conscious, flush the mouth with water for at

least 15 minutes. Do not induce vomiting

unless this is recommended by medical pro-

fessionals. Seek medical attention immedi-

ately.

Tips

Note

If the power adjusting function malfunctions,

the glass in both mirrors can be adjusted by

pressing on the edge of it by hand.

Applies to: vehicles with automatic dimming mirrors

Electrolyte fluid can leak out from broken mir-

ror glass. This liquid damages plastic surfaces

and paint. Clean this liquid as quickly as possi-

ble, for example with a wet sponge.

Dimming the mirrors

Manual dimming rearview mirror

Tips

►

Pull the lever on the bottom of the mirror back.

Applies to: vehicles with automatic dimming mirrors

– If the light reaching the rearview mirror is

obstructed, the automatic dimming mirror

will not function correctly,

Automatic dimming rearview mirror

Applies to: vehicles with automatic dimming mirrors

►

The interior and exterior mirrors dim automati-

– The automatic dimming mirrors do not dim

when the interior lighting is turned on or

the reverse gear is selected.

cally when light shines on them, for example

from headlights on a vehicle behind you.

WARNING

Sun visors

Applies to: vehicles with automatic dimming mirrors

– Electrolyte fluid can leak out from broken

mirror glass. This liquid can irritate the skin,

eyes and respiratory system. If there is con-

tact with the fluid, flush immediately with

plenty of water. Seek medical attention if

necessary.

– Repeated or long-term exposure to electro-

lyte fluid can lead to irritation of the air-

ways, especially in people with asthma or

other respiratory conditions. Take deep

breaths immediately after leaving the vehi-

cle or, if this is not possible, open all of the

doors and windows as wide as possible.

Fig. 50 Roof headliner: sun visor



58

Lights and vision

Sun visor

The sun visors can be moved out of their brackets

and turned toward the doors 1 .

They can also be moved back and forth length-

wise in this position.

Vanity mirror

The mirror light turns on when the cover over the

vanity mirror 2 opens.

Fig. 53 Lever: rear window wiper

►

Move the lever  to the corresponding posi-

Sunshade

Applies to: vehicles with sunshade

tion:

0 Windshield wipers off

1 Rain sensor/intermittent mode. The wind-

shield wipers turn on once the vehicle speed ex-

ceeds approximately 2 mph (4 km/h) and it is

raining. The higher the sensitivity of the rain sen-

sor that is set (switch 6 to the right), the earlier

the windshield wipers respond to moisture on

the windshield. You can deactivate the rain sen-

sor mode, which turns on intermittent mode. In

intermittent mode, you can adjust the interval

time using the switch 6 .

Fig. 51 Rear door: sunshade

Rear door sunshade

►

Applies to: MMI: Select on the home screen:

►

Pull the sunshade out and attach it to the re-

VEHICLE > Light & Visibility > Rain sensor.

tainer on the upper door frame ðfig. 51.

2 Slow wiping

3 Fast wiping

Windshield wipers

4 Single wipe. If you hold the lever in this posi-

tion longer, the wipers switch from slow wiping

to fast wiping.

Turning on the windshield wipers

5 Clean the windshield . The number of wipes

and afterwipes depends on how long the lever is

held in position 5 .

The wipers wipe one time after several seconds

while driving to remove water droplets. You can

turn off this function by moving the lever to posi-

tion 5 within ten seconds of the afterwipe. The

afterwipe function is reactivated the next time

you turn on the ignition.

Fig. 52 Lever: windshield wipers

If you hold the lever in position 5 for longer

than half a second, the edge wiping feature will

be activated. This moves the windshield wipers

closer to the edge of the windshield and per-

forms an afterwipe to clean the residue that



59

Lights and vision

results from the wiping process from the edge of

the windshield. The function is available when

driving at speeds up to 75 mph (120 km/h).

turning on unintentionally and causing

damage to the windshield wiper system.

Tips

The headlight washer system* operates only

when the low beam headlights are on. If you

move the lever into position 5 , the headlights

will be cleaned at regular intervals.

– The windshield wipers turn off when the ig-

nition is turned off. You can activate the

windshield wipers after the ignition is

turned on again by moving the lever to any

position. The single wipe function (lever in

position 4 ) also functions when the igni-

tion is turned off.

7 Wipe the rear window . The number of

wipes depends on the windshield wiper move-

ment.

– Worn or dirty windshield wiper blades result

in streaking. This can affect the rain sensor

function. Check your windshield wiper

blades regularly.

The rear wiper automatically turns on when the

reverse gear is selected and the front windshield

wipers are on and running.

8 Clean the rear window . The number of

wipes depends on how long the lever is held in

position 8 .

– When stopping temporarily, such as at a

traffic light, the speed of the windshield

wipers automatically reduces by one level.

This may also clean the rearview camera, depend-

ing on the vehicle equipment.

Cleaning/changing wiper blades

WARNING

– The rain sensor is only intended to assist the

driver. The driver may still need to turn the

wipers on manually depending on visibility

conditions.

– The windshield must not be treated with

water-repelling windshield coating agents.

Under unfavorable conditions, such as wet-

ness, darkness, and when the sun is low,

these coatings can cause increased glare,

which increases the risk of an accident. They

can also cause wiper blade chatter.

– Properly functioning windshield wiper

blades are required for a clear view and safe

driving ðpage 60, Cleaning/changing wip-

er blades.

Fig. 54 Windshield wipers: replacing the wiper blades

Wiper blade replacement position

►

Turn off the ignition and hold the windshield

wiper lever in position 4 ðpage 59, fig. 52 un-

til the windshield wiper moves into the wiper

blade replacement position.

►

To bring the windshield wipers into the normal

position, turn on the ignition and hold the lever

in position 4 until the windshield wipers go

back to the original position, or drive faster

than 8 mph (12 km/h).

Note

– If there is frost, make sure the windshield

wiper blades are not frozen to the wind-

shield. Turning on the windshield wipers

when the blades are frozen to the wind-

shield can damage the wiper blades.

You can also turn the wiper blade replacement

position on or off in the MMI:

►

Turn the windshield wipers off (position

0

– Prior to using a car wash, the windshield

wiper system must be turned off (lever in

position 0 ). This prevents the wipers from

ðpage 59, fig. 52).



60

Lights and vision for Your Audi S Q5 SUV Third Generation (2025-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals