Get Controls -> Interior equipment Guide for BMW M3 4 Door Fifth Generation (2014-2019)

Interior equipment

Controls

Interior equipment

the safety instructions of the hand-held trans‐

mitter.◀

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

Compatibility

If this symbol is printed on the packag‐

ing or in the owner's manual of the sys‐

tem to be controlled, the system is

generally compatible with the Universal Inte‐

grated Remote Control.

If you have any questions, please contact:

▷

A dealer’s service center or another quali‐

fied service center or repair shop.

Universal Integrated Remote

Control

▷

on the Internet.

HomeLink is a registered trademark of Gentex

Corporation.

Concept

The integrated Universal Remote Control in

the interior mirror can operate up to 3 func‐

tions of remote-controlled systems, such as

garage door drives or lighting systems. The

Universal Integrated Remote Control replaces

up to 3 different hand-held transmitters. To

operate the remote control, the buttons on the

interior mirror must be programmed with the

desired functions. The hand-held transmitter

for the particular system is required in order to

program the remote control.

Control elements on the interior mirror

Before selling the vehicle, delete the stored

functions for the sake of security.

▷

LED, arrow 1.

Buttons, arrow 2.

The hand-held transmitter, arrow 3, is re‐

quired for programming.

Safety information

WARNING

Body parts can be jammed when operat‐

ing remote-controlled systems, e.g., the ga‐

rage door, using the integrated universal re‐

mote control. There is a risk of injury or risk of

property damage. Make sure that the area of

movement of the respective system is clear

during programming and operation. Also follow

Programming

General information

1. Switch on the ignition.

2. Initial setup:

Press and hold the two outer buttons on

the interior mirror simultaneously for ap‐

147

Controls

Interior equipment

proximately 20 seconds until the LED on

the interior mirror flashes. This erases all

programming of the buttons on the interior

mirror.

flashing rapidly and then stays lit constantly for

2 seconds, the system features a rolling code

radio system. Flashing and continuous illumi‐

nation of the LED will repeat for approximately

20 seconds.

3. Hold the hand-held transmitter for the sys‐

tem to be controlled approx. 1 to 3 in‐

ches/2.5 to 8 cm away from the buttons of

the interior mirror. The required distance

depends on the hand-held transmitter.

For systems with a rolling code radio system,

the Universal Integrated Remote Control and

the system also have to be synchronized.

Please read the owner's manual to find out

how to synchronize the system.

4. Simultaneously press and hold the button

of the desired function on the hand-held

transmitter and the button to be program‐

med on the interior mirror. The LED on the

interior mirror will begin flashing slowly.

Synchronizing is easier with the aid of a sec‐

ond person.

Synchronizing the universal remote control

with the system:

5. Release both buttons as soon as the LED

flashes more rapidly. The LED flashing

faster indicates that the button on the inte‐

rior mirror has been programmed.

1. Park the vehicle within range of the re‐

mote-controlled system.

2. Program the desired button on the interior

mirror as described.

If the LED does not flash faster after at

least 60 seconds, change the distance be‐

tween the interior mirror and the hand-held

transmitter and repeat the step. Several

more attempts at different distances may

be necessary. Wait at least 15 seconds be‐

tween attempts.

3. Locate and press the synchronizing button

on the system being programmed. You

have approx. 30 seconds for the next step.

4. Hold down the programmed button on the

interior mirror for approximately 3 seconds

and then release it. If necessary, repeat this

step up to three times in order to finish

synchronization. Once synchronization is

complete, the programmed function will be

carried out.

Canada: if programming with the hand-

held transmitter was interrupted, hold

down the interior mirror button and repeat‐

edly press and release the hand-held

transmitter button for 2 seconds.

Reprogramming individual buttons

1. Switch on the ignition.

6. To program other functions on other but‐

tons, repeat steps 3 to 5.

The systems can be controlled using the inte‐

rior mirror buttons.

2. Press and hold the interior mirror button to

be programmed.

3. As soon as the interior mirror LED starts

flashing slowly, hold the hand-held trans‐

mitter for the system to be controlled ap‐

prox. 1 to 3 inches/2.5 to 8 cm away from

the buttons of the interior mirror. The re‐

quired distance depends on the hand-held

transmitter.

Special feature of the rolling code

wireless system

If you are unable to operate the system after

repeated programming, please check if the

system to be controlled features a rolling code

radio system.

Read the system's owner's manual, or press

the programmed button on the interior mirror

longer. If the LED on the interior mirror starts

148

Interior equipment

Controls

4. Likewise, press and hold the button of the

desired function on the hand-held trans‐

mitter.

hold the two outer buttons on the interior mir‐

ror simultaneously for approximately 20 sec‐

onds until the LED on the interior mirror

flashes rapidly.

5. Release both buttons as soon as the inte‐

rior mirror LED flashes more rapidly. The

LED flashing faster indicates that the but‐

ton on the interior mirror has been pro‐

grammed. The system can then be con‐

trolled by the button on the interior mirror.

Digital compass

Overview

If the LED does not flash faster after at

most 60 seconds, change the distance and

repeat the programming starting with

step 4. Several more attempts at different

distances may be necessary. Wait at least

15 seconds between attempts.

Canada: if programming with the hand-

held transmitter was interrupted, hold

down the interior mirror button and repeat‐

edly press and release the hand-held

transmitter button for 2 seconds.

1

2

Control button

Mirror display

Operation

Mirror display

WARNING

The point of the compass is displayed in the

mirror when driving straight.

Body parts can be jammed when operat‐

ing remote-controlled systems, e.g., the ga‐

rage door, using the integrated universal re‐

mote control. There is a risk of injury or risk of

property damage. Make sure that the area of

movement of the respective system is clear

during programming and operation. Also follow

the safety instructions of the hand-held trans‐

mitter.◀

Operating concept

Various functions can be called up by pressing

the control button with a pointed object, such

as the tip of a ballpoint pen or similar object.

The following setting options are displayed in

succession, depending on how long the con‐

trol button is pressed:

The system, such as the garage door, can be

operated using the button on the interior mirror

while the engine is running or when the ignition

is started. To do this, hold down the button

within receiving range of the system until the

function is activated. The interior mirror LED

stays lit while the wireless signal is being

transmitted.

▷

Pressed briefly: turns display on/off.

3 to 6 seconds: compass zone setting.

6 to 9 seconds: compass calibration.

9 to 12 seconds: left/right-hand steering

setting.

▷

12 to 15 seconds: language setting.

Setting the compass zones

Deleting stored functions

All stored functions will be deleted. The func‐

tions cannot be deleted individually. Press and

Sets the particular compass zones on the vehi‐

cle so that the compass operates correctly; re‐

fer to World map with compass zones.

149

Controls

Interior equipment

World map with magnetic zones

Procedure

1. Press and hold the control button for ap‐

prox. 3 to 4 seconds. The number of the

set compass zone appears in the mirror.

1. Make sure that there are no large metallic

objects or overhead power lines near the

vehicle and that there is sufficient room to

drive around in a circle.

2. To change the zone setting, press the con‐

trol button quickly and repeatedly until the

number of the compass zone that corre‐

sponds with your location appears in the

mirror.

2. Set the currently applicable compass zone.

3. Press and hold the control button for ap‐

prox. 6 to 7 seconds so that "C" appears

on the display. Next, drive in a complete

circle at least once at a speed of no more

than 4 mph/7 km/h. If calibration is suc‐

cessful, the "C" is replaced by the points of

the compass.

The set zone is stored automatically. The com‐

pass is ready for use again after approximately

10 seconds.

Calibrating the digital compass

The digital compass must be calibrated in the

event of the following:

Left/right-hand steering

The digital compass is already set for right or

left-hand steering at the factory.

▷

The wrong compass point is displayed.

The point of the compass displayed does

not change despite changing the direction

of travel.

Setting the language

Press and hold the control button for approx.

12 to 13 seconds. Briefly press the control

button again to switch between English "E"

and German "O".

▷

Not all points of the compass are dis‐

played.

150

Interior equipment

Controls

Settings are stored automatically after approxi‐

mately 10 seconds.

handle. Make sure that children do not use the

lighter and burn themselves.◀

NOTE

If metal objects fall into the socket, they

can cause a short circuit. There is a risk of

property damage. Replace the cigarette lighter

or socket cover again after using the socket.◀

Sun visor

Glare shield

Fold the sun visor down or up.

Vanity mirror

A vanity mirror is located in the sun visor be‐

hind a cover. When the cover is opened, the

mirror lighting switches on.

Ashtray/cigarette lighter

Ashtray

Opening

The lighter is located next to the ashtray.

Push in the lighter.

The lighter can be removed as

soon as it pops back out.

Sockets

General information

The lighter socket can be used as a socket for

electrical equipment while the engine is run‐

ning or when the ignition is switched on.

Raise cover.

Emptying

Take out the insert.

The total load of all sockets must not exceed

140 watts at 12 volts.

Do not damage the socket by using non-com‐

patible connectors.

Lighter

WARNING

Safety information

Contact with hot heating elements or the

hot socket of the cigarette lighter can cause

burns. Flammable materials can ignite if the

cigarette lighter falls down or is held against

the respective objects. There is a risk of fire

and injuries. Hold the cigarette lighter by its

NOTE

Battery chargers for the vehicle battery

can work with high voltages and currents,

which means that the 12 volt on-board net‐

work can be overloaded or damaged. There is

a risk of property damage. Only connect bat‐

151

Controls

Interior equipment

tery chargers for the vehicle battery to the

starting aid terminals in the engine compart‐

ment.◀

In the cargo area

NOTE

If metal objects fall into the socket, they

can cause a short circuit. There is a risk of

property damage. Replace the cigarette lighter

or socket cover again after using the socket.◀

Front center console

The socket is located on the left side in the

cargo area.

USB interface/AUX-IN port

Concept

Mobile devices with USB port can be con‐

nected to the USB interface.

A mobile audio device, e.g., a MP3 player, can

be connected using the AUX-IN port.

Raise the lid and remove the cover or cigarette

lighter.

General information

Rear center console

Depending on the equipment, the USB inter‐

face is located in the center console or in the

glove compartment.

USB interface in the glove

compartment

Mobile storage devices with USB port can be

connected to the USB interface in the glove

compartment.

Common file systems are supported. FAT32

and exFAT are the recommended formats.

Remove the cover.

The following applications are possible:

▷

Exporting and importing profiles, refer to

page 42.

▷

Loading of software updates.

Adding music files to the music collection

and saving the music collection.

152

Interior equipment

Controls

USB interface in the center console

Connecting an external device

In addition to the USB storage devices descri‐

bed above, additional mobile devices with USB

port can be connected to the USB interface in

the center console.

Observe the following when connecting:

▷

Do not use force when plugging the con‐

nector into the USB interface.

▷

Use a flexible adapter cable.

▷

Mobile phones supported by the USB in‐

terface.

Protect the USB storage device against

mechanical damage.

The snap-in adapter features a separate

USB port that is automatically connected

when a compatible mobile phone is in‐

serted.

▷

Due to the large number of USB media

available on the market, it cannot be guar‐

anteed that every device is operable on the

vehicle.

▷

Audio devices with USB port, for example

MP3 player.

Do not expose USB media to extreme envi‐

ronmental conditions, such as very high

temperatures; refer to the owner's manual

of the device.

This allows further uses:

▷

Playing music files via USB audio.

Playing video films via USB video.

Due to the many different compression

techniques, proper playback of the media

stored on the USB storage device cannot

be guaranteed in all cases.

Information about compatible USB devices can

be found at

A connected USB storage device will be

supplied with charging current via the USB

interface if the device supports this. At

higher temperatures, the USB storage de‐

vice may cause a reduction in the charging

current.

Overview

▷

To ensure proper transmission of the

stored data, do not charge a USB storage

device via the onboard socket, when it is

connected to the USB interface.

Depending on how the USB storage device

should be used, settings may be required

on the USB storage device, refer to the

owner's manual of the device.

The USB interface and the AUX-IN port are lo‐

cated in the center armrest.

Non- compatible USB media:

▷

USB hard drives.

USB hubs.

USB memory card readers with multiple in‐

serts.

▷

HFS-formatted USB media.

MTP devices.

The USB interface is located in the glove com‐

partment.

Devices such as fans or lights.

153

Controls

Interior equipment

NOTE

Cargo area

Vehicle parts can be damaged when

folding down the rear backrest. There is a risk

of property damage. Make sure that the area of

movement of the rear backrest including head

restraint is clear when folding down.◀

Enlarging the cargo area

Concept

The cargo area can be enlarged by folding

down the rear seat backrest.

Folding down the rear seat backrest

from the cargo area

General information

The rear seat backrest is divided at a ratio of

60 to 40. The left rear seat backrest is con‐

nected to the center section.

1. Pull the corresponding lever in the cargo

area to release the rear seat backrest.

The rear seat backrests can be folded down

from the cargo area.

Safety information

WARNING

Danger of jamming with folding down the

backrests. There is a risk of injury or risk of

property damage. Make sure that the area of

movement of the rear backrest and the of the

head restraint is clear prior to folding down.◀

2. The unlocked rear seat backrest moves

forward slightly.

3. Fold the rear seat backrest forward.

WARNING

With an unlocked backrest, an unsecured

load can be thrown into the vehicle's interior,

e.g., in case of an accident, braking or evasive

maneuver. There is a risk of injury. Make sure

that the backrest engages into the locking af‐

ter folding it back.◀

WARNING

The stability of the child restraint system

is limited or compromised with incorrect seat

adjustment or improper installation of the child

seat. There is a risk of injuries or danger to life.

Make sure that the child restraint system fits

securely against the backrest. If possible, ad‐

just the backrest tilt for all affected backrests

and correctly adjust the seats. Make sure that

seats and backrests are securely engaged. If

possible, adjust the height of the head re‐

straints or remove them.◀

Fold back the backrest

Return the rear seat backrest to the seating

position and engage it.

154

Controls -> Interior equipment for Your BMW M3 4 Door Fifth Generation (2014-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals