Driving -> Stop and Start for Your Citroen C3 Aircross SUV First Generation (2017-2023)

Driving  
Associated indicator lamp  
Putting the engine into standby  
(STOP mode)  
The engine automatically enters standby mode  
as soon as the driver indicates their intention  
to stop, with the gear lever in neutral and the  
clutch pedal released.  
Stop & Start  
6
Function activated: engine on standby  
(STOP mode).  
The Stop & Start function puts the engine  
temporarily into standby - STOP mode - during  
phases when the vehicle is stationary (e.g. red  
lights, traffic jams). The engine automatically  
restarts - START mode - as soon as the driver  
indicates the intention of moving off again with  
the pressing of the clutch pedal.  
Opening the bonnet  
Before doing anything under the  
bonnet, deactivate the Stop & Start system  
to avoid any risk of injury caused by the  
engine restarting automatically.  
Special cases  
The engine will not go into standby if the  
conditions for operation are not met and in the  
following cases:  
– Steep slope (ascending or descending).  
– Vehicle has not exceeded 10 km/h since the  
last engine start.  
– Needed to maintain a comfortable  
temperature in the passenger compartment.  
– Demisting active.  
– Braking assistance being used.  
In these cases, this indicator lamp flashes  
for a few seconds, then goes off.  
Primarily designed for urban use, the function  
is intended to reduce fuel consumption and  
exhaust emissions as well as the noise level  
when stationary.  
The function does not affect the functionalities  
of the vehicle, in particular the braking.  
Driving on flooded roads  
Before entering into a flooded area,  
it is strongly recommended that you  
deactivate the Stop & Start system.  
For more information on Driving  
recommendations, particularly on flooded  
roads, refer to the corresponding section.  
Deactivation/Reactivation  
The function is activated by default when the  
ignition is switched on.  
After the engine has restarted, STOP  
mode is not available until the vehicle  
has reached a speed of 8 km/h.  
Operation  
Main conditions for operation  
During parking manoeuvres, STOP  
mode is not available for a few  
seconds after coming out of reverse gear or  
turning the steering wheel.  
– The driver’s door must be closed.  
– The driver's seat belt must be fastened.  
– The level of charge in the battery must be  
sufficient.  
– The temperature of the engine must be  
within its nominal operating range.  
– The outside temperature must be between  
0°C and 35°C.  
►ꢀ To deactivate or reactivate the system, press  
this button.  
The indicator lamp is on when the system is  
deactivated.  
41  
Driving  
Restarting the engine (START mode)  
The engine automatically restarts as soon as  
the driver indicates the intention of moving off  
again, with the clutch pedal fully pressed.  
Driving with under-inflated tyres, particularly  
in adverse conditions (heavy load, high  
speed, long journey):  
Overspeed alert  
An audible overspeed alert is triggered  
when the vehicle exceeds predefined speed  
thresholds.  
– worsens road-holding.  
– lengthens braking distances.  
– causes premature wear of the tyres.  
– increases fuel consumption.  
Special cases  
When the vehicle speed is greater than 80  
km/h, the alert is emitted once in 2 minutes if  
the vehicle speed is maintained at 80 km/h.  
When the vehicle speed is greater than 120  
km/h, the alert is emitted every 2 seconds.  
The engine will restart automatically if the  
conditions for operation are met again and in  
the following cases:  
– Vehicle speed exceeds 5 km/h.  
– Some specific conditions (braking assistance,  
air conditioning setting, etc.).  
The inflation pressures defined for the  
vehicle can be found on the tyre  
pressure label.  
For more information on the Identification  
markings, refer to the corresponding  
section.  
This system cannot be modified nor  
deactivated.  
In these cases, this indicator lamp flashes  
for a few seconds, then goes off.  
Under-inflation detection  
Malfunctions  
Checking tyre pressures  
This check should be done when the  
tyres are "cold" (vehicle stopped for 1 hour or  
after a journey of less than 6 miles (10 km) at  
moderate speeds).  
Otherwise, add 0.3 bar to the pressures  
shown on the label.  
This system automatically checks the pressures  
of the tyres while driving.  
In the event of a malfunction, the button’s  
indicator lamp flashes briefly, then remains on.  
Have it checked by a CITROËN dealer or a  
qualified workshop.  
It compares the information given by the wheel  
speed sensors with reference values, which  
must be reinitialised every time the tyre  
pressures are adjusted or a wheel changed.  
The system triggers an alert as soon as it  
detects a drop in the inflation pressure of one  
or more tyres.  
The vehicle stalls in STOP mode  
All of the instrument panel warning lamps  
come on if there is a fault.  
►ꢀ Switch off the ignition then start the engine  
again.  
Under-inflation alert  
It is signalled by the fixed illumination of  
this warning lamp.  
Under-inflation detection does not  
replace the need for vigilance on the  
part of the driver.  
This system does not avoid the need to  
regularly check the tyre pressures (including  
the spare wheel) as well as before a long  
journey.  
12 V battery  
In addition, the following information is given in  
the instrument panel:  
When one tyre is deflated then the  
corresponding tyre is blinking.  
When more than one tyre is deflated then the  
four tyres are blinking.  
The Stop & Start system requires  
a 12 V battery of specific technology and  
specification.  
All work must be carried out only by a  
CITROËN dealer or a qualified workshop.  
42