Advertisement

Advertisement

Safety -> Seat belts for Your Citroen C4 Picasso SUV Second generation (2013-2022)

Safety  
Fastening  
2nd row rear seat belts  
Seat belts  
Front seat belts  
The front seat belts are fitted with a pyrotechnic  
pretensioning and force limiting system.  
This system improves safety in the front  
seats in the event of a front or side impact.  
Depending on the severity of the impact, the  
pretensioning system instantly tightens the seat  
belts against the body of the occupants.  
The pretensioning seat belts are active when  
the ignition is on.  
The force limiter reduces the pressure of the  
seat belt on the chest of the occupant, thus  
improving their protection.  
F Pull the strap, then insert the tongue in the  
buckle.  
F Check that the seat belt is fastened  
correctly by pulling the strap.  
Each of the rear seats is fitted with a three-  
point seat belt with inertia reel and force limiter  
(except for the centre rear seat).  
2nd row rear lateral seat belts  
(storage)  
Unfastening  
Adjusting the height of the front  
belt return  
F Press the red button on the buckle.  
F Guide the seat belt as it reels in.  
F To adjust the height of the anchorage point,  
squeeze the control and slide it up or down  
to the notch desired.  
Guide the strap as it reels in and take the tongue  
to the magnet at the lateral anchoring point.  
106  
Safety  
2nd row rear central seat belt  
Removal and storage  
F Press the red button on the buckle.  
F Guide the seat belt as it reels in.  
Before performing any operations on  
the rear seats, to avoid damage to the  
seat belts check that the lateral belts are  
properly tensioned and fasten the tongues  
to their anchoring point. The central seat  
belt must be completely reeled in.  
The seat belt for the rear central position is  
integrated into the roof.  
F Fasten the strap, flat, to the retention loop.  
To install  
Ensure seat belts are always fastened  
when not in use.  
3rd row rear seat belts  
Seat belt not fastened/  
unfastened alerts  
To install  
5
The instrument panel includes the seat belts not  
fastened warning lamp A as well as the seat belts  
not unfastened identification warning lamp B.  
When the system detects that a seat belt is  
unfastened or fastened, warning lamp A lights  
up as well as the corresponding dot(s) in warning  
lamp B.  
F Pull the strap and insert tongue A into the  
right buckle.  
F Insert tongue B into the left buckle.  
F Check that each buckle is fastened correctly  
by pulling the strap.  
F Detach the seat belt strap from its retention  
loop located in the boot side trim.  
F Pull the strap and insert the tongue into the  
buckle.  
F Check that the seat belt is fastened  
correctly by pulling the strap.  
Removal and storage  
Front seat belts not fastened  
alert  
When the ignition is switched on, warning lamp  
A and the corresponding dots in warning lamp  
B come on if the driver and/or front passenger  
have not fastened their seat belts.  
F Press the red button on buckle B, then the  
button on buckle A.  
F Guide the strap as it reels in and take  
tongue B, then A to the magnet at the  
anchoring point on the roof.  
107  
Safety  
At a speed above 12 mph (20 km/h), these  
warning lamps flash, associated with an  
audible signal, for two minutes. Beyond this  
period of time, the warning lamps stay on  
continuously until the seat belts are fastened.  
Advice  
Installation  
The lower part of the strap must be  
positioned as low as possible on the  
pelvis.  
The upper part must be positioned in the  
hollow of the shoulder.  
The driver must ensure that passengers  
use the seat belts correctly and that they  
are all fastened before setting off.  
Wherever you are seated in the vehicle,  
always fasten your seat belt, even for  
short journeys.  
Do not interchange the seat belt buckles  
as they will not fulfil their role fully.  
The seat belts are fitted with an inertia  
reel permitting automatic adjustment of  
the length of the strap to your size. The  
seat belt is stowed automatically when not  
in use.  
The inertia reels have an automatic  
locking device at the time of a collision,  
during sudden braking or if the vehicle  
turns over. You can release the device by  
pulling the strap firmly and then releasing  
it so that it reels in slightly.  
Rear seat belts not fastened alert  
In order to be effective, a seat belt must:  
-
be tightened as close to the body as  
possible,  
When the ignition is switched on, with the  
engine running or the vehicle moving above  
6 mph (10 km/h), warning lamp A and the  
corresponding dots in warning lamp B come on  
for around thirty seconds, if one or more rear  
passengers have not fastened their seat belts.  
-
be pulled in front of you with a smooth  
movement, checking that it does not  
twist,  
-
-
-
be used to restrain only one person,  
not show any signs of cuts or fraying,  
not be converted or modified to avoid  
affecting its performance.  
Seat belts unfastened alert  
After the ignition is switched on, warning lamp  
A and the corresponding dots in warning lamp  
B come on if the driver and/or one or more  
passengers unfasten their seat belts.  
These warning lamps flash for 30 seconds,  
accompanied by an audible signal. Beyond  
this period of time, the warning lamps stay on  
continuously until the seat belts are fastened.  
Recommendations for children  
Use a suitable child seat if the passenger  
is less than 12 years old or shorter than  
one and a half metres.  
Never use the same seat belt to secure  
more than one child.  
Before and after use, ensure that the seat  
belt is reeled in correctly.  
After folding or moving a seat or rear  
bench seat, ensure that the seat belt is  
positioned and reeled in correctly.  
Never allow a child to travel on your lap.  
For more information on Child seats,  
refer to the corresponding section.  
108