Advertisement

Advertisement

Instruments and controls for Your Citroen Ds4 SUV First Generation (2010-2018)

Instruments and controls  
001  
 
Customisable colour instrument panel - Type 1  
Dials and screens  
Control buttons  
1. Rev counter (x 1 000 rpm or tr/min).  
2. Gear efficiency indicator or gear lever  
position and gear engaged (electronic or  
automatic gearbox).  
3. Analogue speedometer (mph or km/h).  
4. Cruise control or speed limiter setting.  
5. Digital speedometer (mph or km/h).  
6. Engine oil level indicator.  
7. Service indicator  
A. Dial COLOUR: customisation of the  
(miles or km) then,  
total mileage recorder.  
These two functions are displayed  
successively on switching on the ignition.  
Lighting dimmer setting (when making an  
adjustment).  
background colour of the dials.  
B. Screen COLOUR: customisation of the  
background colour of the screens.  
C. Lighting dimmer (available in night mode).  
D. Reminder of the servicing information  
Reset the service indicator or the trip  
mileage recorder.  
8. Trip mileage recorder (miles or km).  
9. Fuel gauge and associated low fuel  
warning lamp.  
10. Range (miles or km).  
 
39  
Monitoring  
Customisable colour instrument panel - Type 2  
Dials and screens  
Control buttons  
1. Rev counter (x 1 000 rpm or tr/min).  
2. Gear shift indicator or gear lever position  
and gear for an electronic or automatic  
gearbox.  
3. Speedometer (mph or km/h).  
4. Central screen.  
6. Trip mileage recorder (miles or km).  
7. Service spanner (if a service is due or  
missed),  
A. Dial COLOUR: customisation of the  
background colour of the dials.  
B. Screen COLOUR: customisation of the  
background colour of the screens.  
C. Dashboard lighting dimmer (in night mode).  
D. Start a manual test (procedure for checking  
the status of systems and display of vehicle  
alerts).  
total mileage recorder.  
(miles or km)  
5. Fuel gauge and associated low fuel level  
warning lamp.  
Reset service indicator or trip mileage  
recorder.  
 
Type 2 instrument panel central screen and controls  
Controls  
There is a button and a thumb wheel to control  
the central screen in the instrument panel:  
A. button on the end of the wiper stalk:  
run through the various active functions  
available.  
B. thumb wheel on the left of the steering  
column,  
-
rotation (other than menu): scroll through  
the list of active functions available,  
press: main menu, confirm the selection,  
rotation (in a menu): move up or down in  
the menu.  
-
-
1. Speed limiter or cruise control settings.  
2. Engine oil level indicator.  
This group of controls allows:  
-
when stationary, configuration of the  
vehicle, central screen and instrument  
panel parameters (driving and comfort  
systems, language, units, sounds...),  
when stationary and while driving,  
scrolling the active functions available  
(trip computer, navigation-guidance...).  
Reminder of the servicing information.  
These functions are displayed successively  
on switching on the ignition, after the  
welcome sequence and before display of  
the active available functions.  
-
Alert or information messages may be  
displayed temporarily.  
 
41  
Monitoring  
Main menu  
Vehicle parameters  
This menu is used to activate or deactivate  
certain driving and comfort systems, classified  
in different categories:  
-
-
"Vehicle lighting" (see "Visibility" section):  
"Directional headlamps" (Main/additional  
directional lighting),  
"Daytime lights" (Daytime running  
lamps).  
"Interior lighting" (see "Visibility" section):  
"Follow-me-home" (Automatic timed  
operation of headlamps),  
Press thumb wheel B for access to the  
main menu and select one of the following  
functions:  
-
"Access to the vehicle" (see "Access"  
section):  
-
-
-
"Vehicle parameters",  
"Display adjustment",  
"Choice of sounds".  
"Plip action" (Selective unlocking of the  
driver's door),  
"Unlocking only boot" (Selective  
unlocking of the boot).  
Turn the thumb wheel B to move around in  
the instrument panel central screen.  
Press the thumb wheel B again to confirm  
the selection.  
"Welcome lighting" (Interior/exterior  
welcome lighting).  
-
"Driving assistance":  
"Parking brake automatic" (Automatic  
electric parking brake; see "Driving"  
section),  
"Rear wipe in reverse gear" (Rear wiper  
coupled to reverse gear; see "Visibility"  
section),  
The main menu and its associated  
functions can only be accessed when  
stationary.  
A message appears in the instrument  
panel central screen, above a certain  
speed threshold, indicating that the  
main menu cannot be displayed.  
"Speeds memorised" (Memorising  
speeds; see "Driving" section).  
 
Rev counter  
Choice of sounds  
This menu allows you to choose a family of  
polyphonic sounds from the four available.  
These sounds are grouped together in a family  
and are adapted to suit the situation and  
context (alert, confirmation, rejection, direction  
indicators, lighting left on, key in ignition...).  
Display conguration  
This menu is used to configure:  
Approaching the maximum engine speed,  
the bars are displayed in red and flash,  
to indicate to you the need to change up a gear.  
-
the display language of the central screen,  
from a pre-defined list,  
-
the units: temperature (°Celsius or  
°Fahrenheit) and fuel consumption  
(l/100 km, mpg or km/l),  
-
the graphical presentation of the central  
screen, from a pre-defined list.  
 
43  
Monitoring  
Warning and indicator lamps  
When the ignition is switched on  
Associated warnings  
Certain warning lamps come on for a few  
seconds when the ignition is switched on.  
When the engine is started, these warning  
lamps should go off.  
If they remain on, before moving off, refer to the  
information on the warning lamp in question.  
The illumination, fixed or flashing, of certain  
warning lamps may be accompanied by  
an audible signal and a message in the  
multifunction screen or in the type 2 instrument  
panel central screen.  
Visual indicators which inform the driver of the  
occurrence of a malfunction (warning lamp)  
or of the operation of a system (operation or  
deactivation indicator lamp).  
 
Warning lamps  
If your vehicle has a screen, a warning lamp coming on is always accompanied by the  
display of an additional message, to assist you in identifying the problem.  
If you encounter any problems, do not hesitate to contact a CITROËN dealer or a qualified  
workshop.  
When the engine is running or the vehicle is  
being driven, the illumination of one of the  
following warning lamps indicates a malfunction  
which requires action on the part of the driver.  
The warning comes on in the instrument panel  
or appears in the type 2 instrument panel  
central screen.  
Warning lamp  
STOP  
is on  
Cause  
Action/Observations  
fixed, alone or  
associated with  
Illumination of this warning lamp is  
associated with a serious fault with  
Stop as soon as it is safe to do so as there is a risk that  
the engine will cut out while driving.  
another warning lamp, the braking system, power steering,  
Park, switch off the ignition and contact a CITROËN  
dealer or a qualified workshop.  
accompanied by an  
audible signal and a  
message in the screen.  
engine lubrication system or cooling  
system.  
Maximum  
fixed red.  
The temperature of the cooling system Stop as soon as it is safe to do so.  
coolant  
is too high.  
Wait until the engine has cooled down before topping  
temperature  
up the level, if necessary.  
If the problem persists, contact a CITROËN dealer or  
qualified workshop.  
Engine oil  
pressure  
fixed.  
There is a fault with the engine  
lubrication system.  
You must stop as soon it is safe to do so.  
Park, switch off the ignition and contact a CITROËN  
dealer or a qualified workshop.  
 
45  
Monitoring  
Warning lamp  
Battery charge  
is on  
Cause  
Action/Observations  
fixed.  
The battery charging circuit has a fault The warning lamp should go off when the engine is  
(dirty or loose terminals, slack or cut  
alternator belt, ...).  
started.  
If it does not go off, contact a CITROËN dealer or a  
qualified workshop.  
Braking  
fixed, associated with  
the STOP warning  
lamp.  
The braking system fluid level has  
dropped significantly.  
You must stop as soon as it is safe to do so.  
Top up with brake fluid recommended by CITROËN.  
If the problem persists, have the system checked by a  
CITROËN dealer or a qualified workshop.  
fixed, associated with  
the electric parking  
brake malfunction  
warning lamp, if the  
parking brake is  
released.  
The braking system has a fault.  
You must stop as soon as it is safe to do so.  
Park, switch off the ignition and contact a CITROËN  
dealer or a qualified workshop.  
+
+
fixed, associated with  
the STOP and ABS  
warning lamps.  
The electronic brake force distribution You must stop as soon as it is safe to do so.  
(EBFD) system has a fault.  
Have it checked by a CITROËN dealer or a qualified  
workshop.  
 
Warning lamp  
Electric parking  
is on  
Cause  
Action/Observations  
flashing.  
The application or release of the  
You must stop as soon as it is safe to do so.  
brake  
electric parking brake was interrupted. Park on level ground, switch off the ignition and  
contact a CITROËN dealer or a qualified workshop.  
Electric  
parking brake  
malfunction  
fixed.  
The electric parking brake has a fault. Automatic application/release is no longer possible.  
Contact a CITROËN dealer or a qualified workshop  
without delay.  
The parking brake can be released manually using the  
emergency release procedure.  
+
For more information on the electric parking brake,  
refer to the "Driving" section.  
Door(s) open  
fixed if the speed is  
below 6 mph (10 km/h).  
fixed and accompanied  
by an audible signal  
if the speed is above  
6 mph (10 km/h).  
A door or the boot is still open.  
Close the door or boot.  
Seat belt not  
fastened/  
unfastened*  
The driver or front passenger has not  
buckled or has unbuckled their seat  
belt.  
fixed, then flashing,  
accompanied by an  
increasing audible  
signal.  
Pull on the belt in question and insert the tongue in  
the buckle.  
This warning repeats the seat belt information given  
by the roof console warning lamps.  
At least one rear passenger has  
unbuckled their seat belt.  
* According to country.  
 
47  
Monitoring  
Warning lamp  
Service  
is on  
Cause  
Action/Observations  
temporarily,  
A minor malfunction has occurred for Identify the malfunction by reading the message  
accompanied by a  
message.  
which there is no specific warning  
lamp.  
displayed in the screen, such as, for example:  
-
-
-
-
-
the opening of the doors, boot or bonnet,  
the engine oil level,  
the remote control battery,  
the tyre pressures,  
saturation of the particle emission filter on  
Diesel vehicles (see "Checks - § Checks/Particle  
emissions filter").  
For any other malfunctions, contact a CITROËN dealer  
or a qualified workshop.  
fixed, accompanied  
by a message and an  
audible signal.  
A major malfunction has occurred  
for which there is no specific warning displayed in the screen and contact a CITROËN dealer  
lamp.  
Identify the malfunction by reading the message  
or a qualified workshop.  
Particle  
emissions filter  
(Diesel)  
fixed, accompanied  
by an audible signal  
message on the risk of saturated.  
blockage of the particle  
emissions filter.  
This indicates that the particle  
emissions filter is starting to become  
As soon as driving conditions allow, regenerate the  
filter by driving at a speed of at least 35 mph (60 km/h)  
until the warning lamp goes off.  
fixed, accompanied by This indicates the low level of the  
Have the reservoir topped up as soon as possible by a  
CITROËN dealer or a qualified workshop.  
an audible signal and  
and a message that the  
particle emissions filter  
additive level is too low.  
additive reservoir.  
 
Warning lamp  
Engine  
is on  
Cause  
Action/Observations  
flashing.  
The engine management system has Risk of destruction of the catalytic converter.  
autodiagnosis  
system  
a fault.  
Have it checked by a CITROËN dealer or a qualified  
workshop.  
fixed.  
The emission control system has a  
fault.  
The warning lamp should go off when the engine is started.  
If it does not go off, contact a CITROËN dealer or qualified  
workshop without delay.  
Low fuel level  
fixed, accompanied by When it first comes on there remains Refuel as soon as possible to avoid running out of  
fuel.  
and audible signal and approximately 6 litres of fuel in the  
Until sufficient fuel is added, this warning lamp will  
come on every time the ignition is switched on,  
accompanied by an audible signal and a message.  
This audible signal and message are repeated  
with increasing frequency as the fuel level drops  
towards "0".  
a message.  
tank.  
At this point, you begin to use the fuel  
reserve.  
Fuel tank capacity: approximately 60 litres.  
Never continue to drive until you run out of fuel,  
as this could damage the emission control and  
injection systems.  
Anti-lock Braking fixed.  
System (ABS)  
The anti-lock braking system has  
a fault.  
The vehicle retains conventional braking.  
Drive carefully at reduced speed and contact a  
CITROËN dealer or a qualified workshop without delay.  
Dynamic stability flashing.  
control (ESP/  
The ESP/ASR regulation is active.  
The system optimises traction and improves the  
directional stability of the vehicle.  
ASR)  
fixed, associated with  
illumination of the indicator  
lamp in the "ESP OFF"  
The ESP/ASR or hill start assist  
system has a fault.  
Have it checked by a CITROËN dealer or a qualified  
workshop.  
button, accompanied by an  
audible signal and a message.  
 
49  
Monitoring  
Warning lamp  
Power steering  
is on  
Cause  
Action/Observations  
fixed.  
The power steering has a fault.  
Drive carefully at reduced speed.  
Have it checked by a CITROËN dealer or a qualified  
workshop.  
Under-inflation  
fixed.  
The pressure in one or more wheels  
is too low.  
Check the pressure of the tyres as soon as possible.  
This check should preferably be carried out when the  
tyres are cold.  
+
flashing then fixed,  
accompanied by the  
Service warning lamp. on one of the wheels.  
The tyre pressure monitoring system  
has a fault or no sensor is detected  
Under-inflation detection is not assured.  
Have the system checked by a CITROËN dealer or a  
qualified workshop.  
Foot on the brake fixed.  
pedal  
The brake pedal is not pressed.  
With an electronic gearbox, press the brake pedal to  
start the engine (lever in position N).  
If you wish to release the parking brake without  
pressing the brake pedal, this warning lamp will remain  
on.  
flashing.  
With an electronic gearbox, if you hold Use the brake pedal and/or the electric parking brake.  
the vehicle on a rising incline using  
the accelerator for too long, the clutch  
overheats.  
Airbags  
temporarily.  
fixed.  
This lamp comes on for a few  
seconds when you turn on the  
ignition, then goes off.  
This lamp should go off when the engine is started.  
If it does not go off, contact a CITROËN dealer or a  
qualified workshop.  
One of the airbag or seat belt  
pretensioner systems has a fault.  
Have it checked by a CITROËN dealer or a qualified  
workshop.  
Directional  
headlamps  
flashing.  
The directional headlamps system  
has a fault.  
Have it checked by a CITROËN dealer or a qualified  
workshop.  
 
Operation indicator lamps  
If one of the following indicator lamps comes on, this confirms that the corresponding system has come into operation.  
It may be accompanied by an audible signal and a message in the screen.  
Warning lamp  
Left-hand  
is on  
Cause  
Action/Observations  
flashing with buzzer.  
The lighting stalk is pushed down.  
direction indicator  
Right-hand  
flashing with buzzer.  
The lighting stalk is pushed up.  
direction indicator  
Hazard warning  
lamps  
flashing with audible  
signal.  
The hazard warning lamps switch,  
located on the dashboard, has been  
operated.  
The left-hand and right-hand direction indicators and  
their associated indicator lamps flash simultaneously.  
On vehicle where the daytime running lamps are deactivated,  
if the lighting control is in the "AUTO" position, the sidelamps  
come on as a luminous signature of the vehicle.  
Sidelamps  
fixed.  
fixed.  
The lighting control is in the  
"Sidelamps" position.  
Dipped beam  
headlamps  
The lighting stalk is in the "Dipped beam  
headlamps" position or in the "AUTO"  
position in conditions of low light.  
Main beam  
headlamps  
fixed.  
fixed.  
The lighting stalk is pulled towards  
you.  
Pull the stalk again to return to dipped beam  
headlamps.  
Front foglamps  
The front foglamps are switched on.  
Turn the ring on the stalk rearwards twice to switch off  
the front foglamps.  
Rear foglamps  
fixed.  
The rear foglamps are switched on.  
Turn the ring on the stalk rearwards to switch off the  
rear foglamps.  
 
51  
Monitoring  
Warning lamp  
Parking brake  
is on  
Cause  
Action/Observations  
fixed.  
The parking brake is applied or not  
properly released.  
Release the parking brake to switch off the warning  
lamp, keeping your foot on the brake pedal.  
Observe the safety recommendations.  
For more information on the parking brake, refer to the  
"Parking brake" and "Electric parking brake" sections.  
Electric parking  
brake  
fixed.  
fixed.  
fixed.  
The electric parking brake is applied. Release the electric parking brake to switch off the  
warning lamp: with your foot on the brake pedal,  
pull the electric brake control.  
Observe the safety recommendations.  
For more information on the electric parking brake,  
refer to the "Driving" section.  
Deactivation of  
the automatic  
functions of the  
electric parking  
brake  
The "automatic application"  
(on switching off the engine) and  
"automatic release" functions are  
deactivated or faulty.  
Activate the function (according to country) via the  
vehicle configuration menu or contact a CITROËN  
dealer or a qualified workshop.  
Diesel engine  
pre-heating  
The ignition switch is at the  
2nd position (ignition on).  
Wait until the warning lamp goes off before starting.  
The period of illumination of the warning lamp is  
determined by the climatic conditions (up to about  
thirty seconds in extreme climatic conditions).  
If the engine does not start, switch the ignition off and  
then on, wait until the warning lamp goes off again,  
then start the engine.  
 
Warning lamp  
is on  
Cause  
Action/Observations  
Automatic wiping fixed.  
The wiper control is pushed  
downwards.  
Automatic front wiping is activated.  
To deactivate automatic wiping, operate the control  
stalk downwards or put the stalk into another position.  
Lighting dimmer fixed.  
The lighting dimmer is making an  
adjustment.  
You can adjust the level of illumination of the  
instruments between 1 and 16.  
Passenger's  
airbag system  
fixed in the seat belt  
The control switch, located in the glove  
box, has been placed in the "ON"  
position.  
The passenger's front airbag is activated.  
In this case, do not install a "rear facing"  
child seat.  
Move the control switch to the "OFF" position  
to deactivate the passenger's front airbag.  
In this case, you can install a "rear facing" child seat.  
and passenger's front  
airbag warning lamps  
display.  
Stop & Start  
fixed.  
When the vehicle stops (red lights,  
traffic jams,...) the Stop & Start  
The warning lamp goes off and the engine restarts  
automatically in START mode, as soon as you want to  
system has put the engine into STOP move off.  
mode.  
flashes for a few  
seconds, then goes  
off.  
STOP mode is temporarily  
unavailable.  
or  
For more information on special cases with STOP  
mode and START mode, refer to the "Stop & Start"  
section.  
START mode is invoked  
automatically.  
Parking space  
sensors  
fixed.  
The parking space sensors function  
is selected.  
To start measurement, operate the direction indicator  
on the side of the space to be measured, and do not  
exceed 12 mph (20 km/h). A message is displayed  
once the measurement has been completed.  
 
53  
Monitoring  
Deactivation indicator lamps  
If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally.  
This is may be accompanied by an audible signal and a message on the multifunction screen.  
Warning lamp  
is on  
Cause  
Action/Observations  
Passenger's  
airbag system  
fixed in the instrument The control switch, located in the  
Set the control to the "ON" position to activate  
the passenger's front airbag.  
In this case, do not fit a child seat in the rear-facing  
position.  
panel and/or seat belt  
and front passenger's  
airbag warning lamps  
display.  
glove box, is set to the OFF position.  
The passenger's front airbag is  
deactivated.  
 
Engine oil level indicator  
Oil level correct  
Oil level indicator error  
This is indicated by the flashing of "OIL--"  
or the display of a specific message in the  
instrument panel. Contact a CITROËN or a  
qualified workshop.  
This information is displayed for a few seconds  
when the ignition is switched on, at the same  
time as the service information.  
Dipstick  
Refer to the "Checks" section to locate the  
dipstick and the oil filler cap on your engine.  
Oil level incorrect  
This is indicated by the flashing of "OIL"  
or the display of a specific message in  
the instrument panel, coupled with the service  
warning lamp and accompanied by an audible  
signal.  
If the low oil level is confirmed by a check  
using the dipstick, the level must be topped up  
to avoid damage to the engine.  
There are 2 marks on the  
dipstick:  
-
A = max; never exceed  
this level (risk of damage to  
the engine),  
The vehicle must be on level ground  
and the engine must have been off  
for more than 30 minutes for this level  
check to be accurate.  
-
B = min; top up the level via  
the oil filler cap, using the  
correct grade of oil for your  
engine.  
 
55  
Monitoring  
Service indicator  
Between 600 miles (1 000 km)  
and 1 800 miles (3 000 km) remain  
before the next service is due  
For a few seconds after the ignition is switched  
on, the spanner symbolising the service  
operations comes on. The distance recorder  
display line or a specific message in the  
instrument panel central screen indicates the  
distance remaining before the next service is due.  
For example: 1 700 miles (2 800 km) remain  
before the next service is due.  
Less than 600 miles (1 000 km) remain  
before the next service is due  
Example: 560 miles (900 km) remain before  
the next service is due.  
For a few seconds after the ignition is switched  
on, the screen indicates:  
For a few seconds after the ignition is switched  
on, the screen indicates:  
This information is displayed for a few seconds  
after switching on the ignition. It informs the  
driver when the next service is due,  
in accordance with the manufacturer's  
servicing schedule.  
A few seconds after the ignition is switched  
on, the distance recorder resumes its normal  
operation. The spanner remains on to  
indicate that a service must be carried out  
soon.  
The point at which the service is due is  
calculated from the last service indicator zero  
reset. It is determined by two parameters:  
A few seconds after the ignition is switched on,  
the spanner goes off; the distance recorder  
resumes its normal operation. The screen then  
indicates the total and trip distances.  
-
-
the distance travelled,  
the time elapsed since the last service.  
More than 1 800 miles (3 000 km)  
remain before the next service is due  
When the ignition is switched on, no service information  
appears in the instrument panel central screen.  
 
Service overdue  
For a few seconds after the ignition is switched on,  
the spanner flashes to indicate that the service  
must be carried out as soon as possible.  
Example: the service is overdue by 180 miles  
(300 km).  
For a few seconds after the ignition is switched on,  
the screen indicates:  
This operation cannot be carried  
out while a reminder of the servicing  
information is being displayed.  
Following this operation, if you wish to  
disconnect the battery, lock the vehicle  
and wait at least five minutes for the  
zero reset to be registered.  
A few seconds after the ignition is switched  
on, the distance recorder resumes its normal  
operation. The spanner remains on.  
Service indicator zero reset  
Recalling the service information  
After each service, the service indicator must  
be reset to zero.  
You can recall the service information at any  
time.  
The procedure for resetting to zero is as  
follows:  
Briefly press the ".../000" trip distance  
recorder zero reset button.  
switch off the ignition,  
press and hold the ".../000" trip distance  
recorder zero reset button,  
switch on the ignition; the distance recorder  
display begins a countdown,  
when the screen indicates "=/0" and the  
spanner disappears, release the button.  
The service information is displayed for a  
few seconds, in the total distance recorder  
line or in the type 2 instrument panel  
central screen.  
The distance remaining may be  
weighted by the time factor, depending  
on the type of driving.  
Therefore, the spanner may also come  
on if you have exceeded the two year  
service interval.  
 
57  
Monitoring  
Manual test in the type 2 instrument panel central screen  
This function allows you to check the status of the vehicle systems (reminder of the "activated"/"deactivated" status of the configurable functions) and to  
display the alerts log.  
The following information appears successively  
in the instrument panel central screen:  
With the engine running, to start a manual  
test, briefly press the ".../000" button on  
the instrument panel.  
This information also appears every  
time the ignition is switched on  
(automatic test).  
-
-
-
engine oil level indicator  
(see corresponding section),  
service indicator (see corresponding  
section),  
under-inflation detection (if your vehicle  
is fitted with this system; see the "Safety"  
section),  
-
-
current warnings and alert messages,  
if any (see corresponding section for the  
warning lamp or system concerned),  
status of configurable functions  
(see "Multifunction screens").  
 
Distance recorders  
The total and trip distances are displayed for  
thirty seconds when the ignition is switched off,  
when the driver's door is opened and when the  
vehicle is locked or unlocked.  
Total distance recorder  
Trip distance recorder  
Measures the total distance travelled by the  
vehicle since its first registration.  
Measures the distance travelled since it was  
last reset to zero by the driver.  
With the ignition on, press and hold this  
button until zeros appear.  
 
59  
Monitoring  
Lighting dimmer  
Activation  
Press button A to change the brightness of  
the instruments and controls.  
When the lighting reaches the minimum  
setting, release the button, then press  
again to increase it.  
or  
When the lighting reaches the maximum  
setting, release the button, then press  
again to reduce it.  
When the lighting reaches the level of  
brightness required, release the button.  
Permits manual adjustment of the brightness of  
the instruments and controls in relation to the  
exterior brightness. Only operates when the  
vehicle lighting is on in night mode.  
You can also modify the level of lighting by  
turning the thumb wheel B, located on the left  
of the steering wheel:  
This indicator and the lighting  
value appear in the middle of the  
instrument panel during adjustment  
to show the lighting level compared  
to the 16 levels available.  
upwards; to reduce the level,  
downwards; to increase the level.  
Deactivation  
When the vehicle lighting is off, or in day mode  
(daytime running lamps on), pressing the button  
or turning the thumb wheel does not have any  
effect.  
 
Black panel (black screen)  
Customising the instrument  
panel colours  
In the instrument panel, you can change the  
colour of its dials (button A) independently from  
that of the screens (button B).  
There are five colour variants, from white to  
blue.  
System allowing certain screens to be switched  
off for night driving.  
Activation  
With the vehicle lighting on, press this  
The instrument panel remains on with the  
vehicle speed, electronic or automatic gearbox  
gear selected, cruise control or speed limiter  
information, if in use, and the low fuel alerts as  
appropriate.  
press the appropriate button as many times  
as needed to obtain the desired colour.  
button again to activate the black panel.  
Press once more to illuminate on the  
various screens again.  
If there is an alert or a change in a function  
or to a setting, the black panel mode is  
interrupted.  
 
61  
Monitoring  
Customising the polyphonic  
sounds  
This menu allows you to choose a family of  
polyphonic sounds from the four available.  
These sounds are grouped together in a family  
and are adapted to suit the situation and  
context (alert, confirmation, rejection, direction  
indicators, lighting left on, key in ignition...).  
For the type 1 customisable  
colour instrument panel  
For the type 2 customisable  
colour instrument  
Press the "MENU" button for access to the  
main menu.  
Select the "Personalisation-configuration"  
menu and confirm.  
Select the "Choice of sounds" line and  
confirm.  
Select the desired family of sounds and  
confirm.  
Press the thumb wheel for access to the  
main menu.  
Select the "Choice of sounds" line and  
confirm.  
Select the desired family of sounds and  
confirm.  
Save the modifications by confirming "OK".  
Save the modifications by confirming "OK".  
For safety reasons, the driver must  
only carry out these operation when  
stationary.  
For safety reasons, these operations  
are only possible when stationary.