Get Instruments and controls Guide for Citroen Ds5 SUV First Generation (2011-2018)

001

Instruments and controls

Petrol-Diesel instrument panel

dials and screens

control buttons

1. Rev counter (x 1 000 rpm or tr/min),

graduation according to engine (petrol or

Diesel).

6. Gear shift indicator or gear lever position

A. Main lighting and controls dimmer.

B. - Short press: display in turn of servicing

information, remaining range for the

AdBlue additive and the alert log.

and gear engaged for an automatic

gearbox.

2. Fuel gauge.

7. Instrument panel screen: distance

recorders, service indicator, engine oil

level indicator*, remaining range for the

AdBlue additive and the SCR system*, alert

messages, trip computer, media currently

playing, navigation instructions*.

3. Engine coolant temperature gauge.

4. Analogue speedometer (mph or km/h).

5. Cruise control or speed limiter settings.

- Long press: reset the service indicator or

trip recorder (depending on context).

8. Digital speedometer (mph or km/h).

When switching the ignition on or off,

the speedometer needle and the bars of

the dials carry out a full sweep and then

return to 0.

* Depending on version.

19

Monitoring

Indicator and warning lamps

Visual indicators informing the driver that a

system is in operation, switched off or has a

fault.

When the engine is started, these same

warning lamps should go off.

If they remain on, before moving off, refer to the

information on the warning lamp concerned.

Certain warning lamps may come on in

one of two modes: fixed (continuous) or

flashing.

Only by relating the type of illumination

to the operation of the vehicle can it

be determined whether the situation is

normal or a fault has occurred.

Refer to the tables on the following

pages for more information.

When the ignition is switched on

Associated warnings

Certain warning lamps come on for a few

seconds in the instrument panel and/or

instrument panel screen when the vehicle's

ignition is switched on.

The switching on of certain warning lamps may

be accompanied by an audible signal and a

message in the instrument panel screen.

The warning lamps may come on continuously

(fixed) or flash.

Operation indicator lamps

If one of the following indicator lamps comes on in the instrument panel and/or instrument panel screen, this confirms that the corresponding system has come into operation.

Warning / indicator lamp State

cause

Action / Observations

Left-hand

flashing with buzzer.

The lighting stalk is pushed down.

direction indicator

Right-hand

flashing with buzzer.

The lighting stalk is pushed up.

direction indicator

Sidelamps

fixed.

The lighting stalk is in the

"Sidelamps" position.

dipped beam

headlamps

The lighting stalk is in the "Dipped

beam headlamps" position.

Main beam

headlamps

The lighting stalk is pulled towards

you.

Pull the stalk to return to dipped beam headlamps.

The camera, located in the interior rear view mirror,

Automatic

headlamp

dipping

The lighting stalk has been pulled

towards you and the button has been authorises or not switching between main and dipped

pressed.

Its indicator lamp is on.

beam, depending on the exterior lighting and the

driving conditions.

Pulling the lighting stalk to return to dipped beam.

Front

foglamps

fixed.

The front foglamps are switched on

using the ring on the lighting control

stalk.

Turn the ring on the lighting control stalk rearward

twice to switch off the front foglamps.

For more information on the lighting controls, refer to the corresponding section.

21

Monitoring

Warning / indicator lamp State

cause

Action / Observations

Rear foglamps

fixed.

The rear foglamps are on.

Turn the ring on the stalk rearward to switch off the

rear foglamps.

diesel engine

pre-heating

fixed.

The START/STOP switch has been

pressed (ignition on).

Wait until the warning lamp goes off before starting.

Once it goes off, starting is immediate, on condition

that the brake pedal remains pressed with an

automatic gearbox, or the clutch pedal is pressed fully

down with a manual gearbox.

The period of illumination of the warning lamp is

determined by the ambient conditions (up to about

thirty seconds in severe winter conditions).

If the engine does not start, switch the ignition off and

then on, wait until the warning lamp goes off again,

then start the engine.

Electric parking

brake

fixed.

The electric parking brake is applied. Release the electric parking brake to switch off the

warning lamp: with your foot on the brake pedal, pull

the electric parking brake control lever.

Observe the safety recommendations.

For more information on the electric parking brake,

refer to the corresponding section.

deactivation of

the automatic

functions of the

electric parking

brake

The "automatic application" (on

switching off the engine) and

"automatic release" functions are

deactivated or faulty.

Activate the function (depending on the country of

sale) via the vehicle configuration menu or contact a

CITROËN dealer or a qualified workshop if automatic

application / release is not possible.

For more information on the electric parking brake,

refer to the corresponding section.

Warning / indicator lamp State

cause

Action / Observations

Automatic

wiping

fixed.

The wiper control is pushed

downwards.

Automatic front wiping is activated.

To deactivate automatic wiping, operate the control

stalk downwards or put the stalk into another position.

Passenger's

airbag system

fixed in the seat belt

and passenger's front

airbag warning lamps

display.

The control switch, located in the glove

box, has been placed in the "ON"

position.

Move the control switch to the "OFF" position to

deactivate the passenger's front airbag.

In this case, you can install a rearward facing child

The passenger's front airbag is activated. seat, unless there is a fault with the airbags (airbag

In this case, do not install a rearward

facing child seat on this seat.

warning lamp on).

Stop & Start

fixed.

When the vehicle stops (red lights,

traffic jams, ...) the Stop & Start

system has put the engine into

STOP mode.

The warning lamp goes off and the engine restarts

automatically in START mode, as soon as you want to

move off.

flashes for a few

seconds, then goes

off.

STOP mode is temporarily

unavailable.

or

For more information on Stop & Start, refer to the

corresponding section.

START mode is invoked

automatically.

23

Monitoring

deactivation indicator lamps

If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally.

This is may be accompanied by an audible signal and a message in the instrument panel screen.

Warning / indicator lamp State

cause

Action / Observations

Passenger's

airbag system

fixed in the instrument The control switch, located in the

Set the control to the "ON" position to activate the

passenger's front airbag.

In this case, do not install a rearward facing child seat

on this seat.

panel and/or seat belt

and front passenger's

airbag warning lamps

display.

glove box, is set to the OFF position.

The passenger's front airbag is

deactivated.

You can install a rearward facing

child seat, unless there is a fault with

the airbags (airbag warning lamp on).

Warning lamps

When the engine is running or the vehicle is being driven, illumination of one of the following warning lamps indicates a fault which requires action on

the part of the driver.

Any fault resulting in the illumination of a warning lamp must be investigated further by reading the associated message in the instrument panel

screen.

If you encounter any problems, contact a CITROËN dealer or a qualified workshop.

Warning / indicator lamp State

STOP fixed, associated

cause

Action / Observations

Illumination of this warning lamp is

related to a serious fault with the

braking system, power steering, the

engine oil pressure or engine coolant dealer or a qualified workshop.

temperature or a major electrical

fault.

Stop as soon as it is safe to do so as the engine may

cut out.

Park, switch off the ignition and call a CITROËN

with another warning

lamp, accompanied

by an audible signal

and a message in the

screen.

25

Monitoring

Warning / indicator lamp State

Service temporarily,

cause

Action / Observations

One or more minor faults for which

there is no specific warning lamp

have been detected.

Identify the cause of the fault using the message

displayed in the screen.

accompanied by

a message.

You can deal with some problems yourself, such as a

door open or the start of saturation of the particle filter

(as soon as the traffic conditions allow, regenerate

the filter by driving at a speed of at least 40 mph

(60 km/h), until the warning lamp goes off).

For any other problems, such as a fault with the tyre

under inflation detection system, contact a CITROËN

dealer or a qualified workshop.

fixed, accompanied by One or more major faults for which

Identify the cause of the fault using the message

displayed in the screen; you must then contact a

CITROËN dealer or a qualified workshop.

a message.

there is no specific warning lamp

have been detected.

fixed, associated with the The servicing interval has been

Only on BlueHDi Diesel versions.

flashing and then fixed

display of the service

indicator spanner.

exceeded.

Your vehicle must be serviced as soon as possible.

Warning / indicator lamp State

cause

Action / Observations

Electric parking

brake

flashing.

The electric parking brake is not

applied automatically.

The application/release is faulty.

You must stop as soon as it is safe to do so.

Park on flat level ground, engage a gear (or place the

lever in position P for an automatic gearbox), switch

off the ignition and contact a CITROËN dealer or a

qualified workshop.

Electric parking

brake fault

fixed.

The electric parking brake has a fault. Contact a CITROËN dealer or a qualified workshop

without delay.

For more information on the electric parking brake,

refer to the corresponding section.

deactivation of

the automatic

functions of the

electric parking

brake

The "automatic application" (on

switching off the engine) and

"automatic release" functions are

deactivated or faulty.

Activate the function (depending on the country of

sale) via the vehicle configuration menu or contact a

CITROËN dealer or a qualified workshop if automatic

application / release is not possible.

For more information on the electric parking brake,

refer to the corresponding section.

27

Monitoring

Warning / indicator lamp State

cause

Action / Observations

Braking

fixed.

The brake fluid level has dropped

significantly.

You must stop as soon as it is safe to do so.

Top up with brake fluid listed by CITROËN.

If the problem persists, have the system checked by a

CITROËN dealer or a qualified workshop.

+

fixed, associated

with the ABS warning

lamp.

The electronic brake force distribution You must stop as soon as it is safe to do so.

(EBFD) system has a fault.

Have it checked by a CITROËN dealer or a qualified

workshop.

Anti-lock

Braking System

(ABS)

fixed.

The anti-lock braking system has a

fault.

The vehicle retains conventional braking.

Drive carefully at reduced speed and contact a

CITROËN dealer or a qualified workshop without

delay.

dynamic

stability control

(dSc/ASR)

flashing.

fixed.

The DSC/ASR regulation is

operating.

The system optimises traction and improves the

directional stability of the vehicle in the event of loss of

grip or trajectory.

The DSC/ASR system has a fault.

Have it checked by a CITROËN dealer or a qualified

workshop.

Warning / indicator lamp State

cause

Action / Observations

Engine

flashing.

The engine management system has Risk of destruction of the catalytic converter.

autodiagnosis

system

a fault.

Have it checked by a CITROËN dealer or a qualified

workshop.

fixed.

The emission control system has

a fault.

The warning lamp should go off when the engine is started.

If it does not go off, contact a CITROËN dealer or

qualified workshop without delay.

Low fuel level

fixed with the two last

bars flashing,

When it first comes on there remains You must refuel as soon as possible to avoid running

approximately 6 litres of fuel in the out of fuel.

accompanied by a

message and an

audible signal.

tank.

This warning lamp will come on every time the ignition

is switched on, accompanied by a message and an

audible signal, until a sufficient addition of fuel is

made.

This audible signal and message are repeated with

increasing frequency as the fuel level drops and

approaches "0".

Fuel tank capacity: approximately 60 litres.

Never continue to drive until you run out of fuel as

this could damage the emission control and injection

systems.

Under-inflation

fixed.

The pressure in one or more wheels

is too low.

Check the pressure of the tyres as soon as possible.

This check should preferably be carried out when the

tyres are cold.

+

flashing then fixed,

accompanied by the

Service warning lamp. on one of the wheels.

The tyre pressure monitoring system

has a fault or no sensor is detected

Under-inflation detection is not assured.

Have the system checked by a CITROËN dealer or a

qualified workshop.

29

Monitoring

Warning / indicator lamp State

cause

Action / Observations

AdBlue^®additive fixed, on switching

(BlueHdi diesel) on the ignition,

accompanied by an

The remaining driving range is

between 350 miles (600 km) and

1500 miles (2400 km).

Have the AdBlue^®additive tank topped up as soon

as possible: go to a CITROËN dealer or a qualified

workshop, or carry out this operation yourself.

audible signal and a

message indicating the

remaining driving range.

flashing associated with The remaining driving range is

You must top-up the AdBlue^®additive tank to avoid

a breakdown: go to a CITROËN dealer or a qualified

workshop, or carry out this operation yourself.

the SERVICE warning

lamp, accompanied by

an audible signal and a

message indicating the

remaining driving range.

between 0 and 350 miles (600 km).

+

flashing, associated

with the SERVICE

warning lamp,

accompanied by an

audible signal and a

message indicating that

starting is prevented.

The AdBlue^®tank is empty: the

starting inhibition system required

by legislation prevents starting of the

engine.

To be able to start the engine, you must top-up the

AdBlue^®additive tank: go to a CITROËN dealer or

a qualified workshop, or carry out this operation

yourself.

It is essential to add at least 3.8 litres of AdBlue^®to

the additive tank.

For topping-up or for more information on the AdBlue^®additive, refer to the corresponding section.

Warning / indicator lamp State

cause

Action / Observations

ScR emissions

control system

fixed, on switching

on the ignition,

A fault with the SCR emissions

control system has been detected.

This alert disappears once the exhaust emissions

return to normal levels.

+

(BlueHdi diesel) associated with the

SERVICE and engine

diagnostic warning

lamps, accompanied

by an audible signal

and a message.

flashing, on switching

on the ignition,

After confirmation of the fault with the Contact a CITROËN dealer or a qualified workshop

emissions control system, you can

drive for up to 650 miles (1 100 km)

before the engine starting inhibition

system is triggered.

without delay, to avoid a breakdown.

associated with the

SERVICE and engine

diagnostic warning

lamps, accompanied by

an audible signal and

a message indicating

the remaining driving

range.

flashing, on switching

on the ignition,

You have exceeded the authorised

driving limit following confirmation

of a fault with the emissions control

system: the engine starting inhibition

system prevents starting of the

engine.

To be able to start the engine, you must call on a

CITROËN dealer or a qualified workshop.

associated with the

SERVICE and engine

diagnostic warning

lamps, accompanied

by an audible signal

and a message.

31

Monitoring

Warning / indicator lamp State

cause

Action / Observations

Seat belt(s)

not fastened /

unfastened

fixed

or flashing

accompanied by an

audible signal.

A seat belt has not been fastened or

has been unfastened.

Pull the strap then insert the tongue in the buckle.

Airbags

on temporarily.

fixed.

This lamp comes on for a few

seconds when you turn on the

ignition, then goes off.

This lamp should go off when the engine is started.

If it does not go off, contact a CITROËN dealer or a

qualified workshop.

One of the airbag or seat belt

pretensioner systems has a fault.

Have it checked by a CITROËN dealer or a qualified

workshop.

directional

headlamps

flashing.

The directional headlamps system

has a fault.

Have it checked by a CITROËN dealer or a qualified

workshop.

coolant

temperature gauge

After driving for a few minutes, the temperature

and pressure in the cooling system increase.

To top up the level:

F

wait for the engine to cool,

unscrew the cap by two turns to allow the

pressure to drop,

F

when the pressure has dropped, remove

the cap,

top up the level to the "MAX" mark.

With the engine running:

-

in zone A, the temperature is correct,

in zone B, the temperature is too high; the

central STOP warning lamp comes on,

accompanied by an audible signal and a

message in the instrument panel screen.

Be aware of the risk of burns when

topping up the cooling system. Do not

fill above the maximum level (indicated

on the reservoir).

You MUST stop as soon as it is safe to do so.

Wait a few minutes before switching off the

engine.

Contact a CITROËN dealer or a qualified

workshop.

33

Monitoring

Service indicator

More than 1 800 miles (3 000 km)

remain before the next service

is due

When the ignition is switched on, no service

information appears in the instrument panel

screen.

Between 600 miles (1 000 km) and 1 800 miles

(3 000 km) remain before the next service is due

For a few seconds after the ignition is switched

on, the spanner symbolising the service

operations comes on and a message is

displayed in the instrument panel indicating

the distance or time remaining before the next

service is due.

Example: 1 900 miles (2 800 km) remain

before the next service is due.

When the ignition is switched on, the

instrument panel screen temporarily indicates:

System which informs the driver when the

next service is due, in accordance with the

manufacturer's service schedule.

The point at which the service is due is

calculated from the last service indicator reset

to zero, according to the mileage covered and

the time elapsed since the last service.

A few seconds after the ignition is switched on,

the spanner goes off.

For BlueHDi Diesel versions, depending

on the country of sale, the degree of

deterioration of the engine oil may also

be taken into account.

Less than 600 miles (1 000 km)

Service overdue

remain before the next service is due

The spanner may come on if you have

exceeded the period since the last service,

as indicated in the manufacturer's service

schedule.

For a few seconds after the ignition is switched

on, the spanner flashes to indicate that

the service must be carried out as soon as

possible.

Example: the service is overdue by 300 miles.

When the ignition is switched on, the instrument

panel screen indicates:

Example: 500 miles (900 km) remain before

the next service is due.

For a few seconds after the ignition is switched

on, the instrument panel screen indicates:

For BlueHDi Diesel versions, the

spanner may also come on early,

according to the level of deterioration

of the engine oil, which depends on the

driving conditions in which the vehicle

is used.

After the message disappears, the spanner

remains on alongside the mileage recorder as

a reminder that a service must be carried out

soon.

The spanner remains on alongside the

mileage recorder to indicate that a service is

overdue.

With BlueHDi Diesel versions, the

Service warning lamp also comes on

when the ignition is switched on.

35

Monitoring

Retrieving the service

information

Resetting the service indicator

You can access the service information at any

time.

If you have to disconnect the battery

following this operation, lock the vehicle

and wait at least five minutes for the

reset to be registered.

F

Press the trip distance recorder zero reset

button.

The service information is displayed for a

few seconds, then disappears.

After each service, the service indicator must

be reset to zero.

If you have carried out the service on your

vehicle yourself:

F

switch off the ignition,

press and hold the trip distance recorder

zero reset button,

F

switch on the ignition; the distance recorder

display begins a countdown,

when the display indicates "=0", release

the button; the spanner disappears.

Engine oil level

indicator*

On versions fitted with an electric oil level

indicator, the state of the engine oil level is

displayed in the instrument panel for a few

seconds, after the servicing information.

Oil level correct

Oil level indicator fault

The level read will only be correct if

the vehicle is on level ground and the

engine has been off for more than

30 minutes.

This is signalled by the display of the message "Oil

level measurement invalid" in the instrument panel.

Contact a CITROËN dealer or a qualified

workshop.

In the event of a fault with the electric indicator,

the oil level is no longer monitored.

If the system is faulty, you must check the

engine oil level using the manual dipstick

located under the bonnet.

For more information on checking the levels,

refer to the corresponding section.

Oil level incorrect

This is indicated by the display of the message

"Oil level incorrect" in the instrument panel

screen, accompanied by the service warning

lamp and an audible signal.

If the low oil level is confirmed by a check using

the dipstick, the level must be topped up to

avoid damage to the engine.

For more information on checking the levels,

refer to the corresponding section.

* Depending on version.

37

Monitoring

distance recorders

Lighting dimmer

The total and trip distances are displayed for thirty seconds when the ignition is switched off, when

the driver's door is opened and when the vehicle is locked or unlocked.

This allows manual adjustment of the

brightness of the instruments and controls

when driving at night.

Total distance recorder

Trip distance recorder

It measures the total distance travelled by the

vehicle since its first registration.

It measures the distance travelled since it was

reset to zero by the driver.

When the lighting is on:

F

press this button to adjust the brightness of

the instruments and controls,

F

With the ignition on, press the button until

zeros appear.

F

when the level of brightness required is

reached, release this button.

When travelling abroad, you may

have to change the units of distance:

the display of road speed must be in

the official units (miles or km) for the

country. The change of units is done via

the screen configuration menu, with the

vehicle stationary.

The setting is memorised when switching off

the ignition.

Pressing this button does not have any

effect when the exterior lighting is off.

Clock

Black panel (comfortable

night display) with the

touch screen

F

With the exterior lighting on,

press this button to activate the

function.

The analogue clock does not have an

adjustment button.

F

Press this button again or press the

instrument panel lighting dimmer button to

deactivate the function.

To set the time, refer to the section relating to

the screen (audio system) configuration menu.

The clock is synchronised with the screen time;

once the the setting has been confirmed in the

screen, the hands will turn to synchronise with

the screen, as well as every time the ignition is

switched on.

This allows some of the instrument panel

displays, as well as the touch screen, to be

switched off when driving at night, so as to

reduce visual fatigue for the driver.

The essential driving information, such as

the vehicle speed, warning lamps, the gear

engaged for an automatic gearbox, cruise

control or speed limiter, remains displayed in

the instrument panel.

Touch screen

You can return to the current display

at any time by by pressing the blank

screen or one of the menu buttons.

In automatic illumination of headlamps

mode, the "Black panel" function is

automatically deactivated once the

ambient light reaches an adequate

level.

39

Monitoring

Monochrome screen C

displays in the screen

controls

Main menu

F

Press the "MENU" button for access to the

main menu:

-

"Multimedia",

"Telephone",

"Bluetooth connection",

"Personalisation-configuration",

Press the "7" or "8" button to select the

menu required, then confirm by pressing

the "OK" button.

Depending on the context, it displays:

From the control panel of your Audio system,

press:

-

time,

date,

F

button A to chooses between the display

of audio information in full screen or the

shared display of the audio source and the

time,

ambient temperature (this flashes if there is

a risk of ice),

-

visual parking sensor information,

current audio source,

telephone or Bluetooth system information,

settings menus for the screen and the

vehicle equipment.

F

the "MENU" button for access to the main

menu,

the "5" or "6" buttons to scroll through the

items in the screen,

the "7" or "8" buttons to change a setting

value,

the "OK" button to confirm,

or

the "Back" button to abandon the

operation in progress.

"Multimedia" menu

"Bluetooth

"Personalisation-

configuration"

menu

connection" menu

With the audio system switched on, this

menu allows you to activate or deactivate the

functions associated with use of the radio

(RDS, DAB / FM auto tracking, RadioText

(TXT) display) or to choose the media play

mode (Normal, Random, Random all, Repeat).

For more information on the "Multimedia"

application, see the "Audio and telematics"

section.

Wit the audio system on, this menu allows a

Bluetooth device (telephone, media player)

to be connected or disconnected and the

connection mode to be defined (hands-free,

playing audio files).

For more information on the "Bluetooth

connection" application, see the "Audio and

telematics" section.

This menu gives access to the following

functions:

-

"Define the vehicle parameters",

"Choice of language",

"Display configuration",

"Telephone" menu

Deﬁne the vehicle parameters

This menu allows you to activate or deactivate

the following equipment, classified in different

categories:

With the audio system switched on, this menu

allows you to make a call or view the various

telephone directories.

For more information on the "Telephone"

application, see the "Audio and telematics"

section.

-

"Access to the vehicle" (see the "Access"

section):

● "Plip action" (Selective unlocking of the

driver's door),

● "Unlocking boot only" (Selective

unlocking of the boot).

41

Monitoring

-

"Driving assistance":

F

Press the "7" or "8" buttons to set the

● "Parking brake automatic" (Automatic

electric parking brake; see the "Driving"

section),

value required (15, 30 or 60 seconds), then

press the "OK" button to confirm.

● "Rear wipe in reverse gear" (Rear

wiper coupled to reverse gear; see the

"Visibility" section),

For example: setting of the duration of the

"follow-me-home" lighting

● "Speeds memorised" (Memorising

speeds; see the "Driving" section).

"Vehicle lighting" (see the "Visibility"

section):

● "Directional headlamps" (Main /

additional directional lighting),

"Interior lighting" (see the "Visibility"

section):

F

Press the "7" or "8" buttons, to select the

"Define the vehicle parameters" menu,

then the "OK" button.

-

F

Press the "5" or "6" buttons, then the

"OK" button to select the "OK" box and

confirm or press the "Back" button to

cancel.

● "Follow-me-home headlamps"

(Automatic operation of headlamps after

switching off the ignition),

● "Welcome lighting" (Exterior welcome

lighting),

F

Press the "5" or "6" buttons to select

the "Interior lighting" line, then the

"OK" button; then follow the same

procedure to select the "Follow-me-home

headlamps" line.

● "Mood lighting" (Mood lighting).

choice of language

The analogue clock, located in the

dashboard, is synchronised with the

time in the screen. It is set after the

time is adjusted using the configuration

menu and every time the ignition is

switched on.

Once this menu has been selected, you can

choose the language used by the display from

a pre-defined list.

Adjusting the date and time

F

Press the "7" or "8" button to display

the "Display configuration" menu, then

press "OK".

Press the "5" or "6" button to select the

"Date and time adjustment" button, then

press "OK".

Press the "7" or "8" button to select

the setting to modify. Confirm by

pressing "OK", then modify the setting and

confirm again to save the modification.

Adjust the settings one by one, confirming

with the "OK" button.

Display conﬁguration

This menu gives access to the following

settings:

F

-

"Choice of units",

"Date and time adjustment",

"Display parameters",

"Brightness".

Press the "5" or "6" button, then the "OK"

button to select the "OK" box and confirm

or the "Back" button to cancel.

As a safety measure, configuration of

the multifunction screen by the driver

must only be done when stationary.

43

Monitoring

Touch screen

Associated with the navigation system, this

screen gives access to:

General operation

-

menus for adjusting settings for vehicle

functions and systems,

Recommendations

Its use is possible at all temperatures and when

wearing gloves.

Do not use pointed objects on the touch

screen.

Do not touch the touch screen with wet hands.

Uses a soft clean cloth to clean the touch

screen.

Principles

Press the virtual buttons in the touch screen.

Each menu is displayed over one or two pages

(primary page and secondary page).

-

audio and display settings menus,

audio system and telephone controls and

the display of associated information.

the controls for the navigation system

and Internet services and the display of

associated information.

-

Use the "Options" button to go to the

secondary page.

It also allows the display of:

-

the ambient temperature (a blue snowflake

appears if there is a risk of ice),

the trip computer,

visual parking sensor information,

the image from the reversing camera.

After a few moments with no action on

the secondary page, the primary page

is displayed automatically.

-

Use this button for access to

additional information and to the

settings for certain functions.

For versions equipped with a navigation

system in the touch screen, refer to the

supplement in the handbook pack.

As a safety measure, the driver

should only carry out operations

that require close attention with the

vehicle stationary.

Use this button to confirm.

Use this button to quit the current

display and return to the primary

page.

Some functions are not accessible

when driving.

Menus

Press one of the buttons on the control panel

for direct access to a particular menu.

driving

Allows settings to be adjusted for

certain vehicle functions.

See the corresponding section.

Navigation.

See the "Audio and telematics"

section.

Radio Media.

See the "Audio and telematics"

section.

Telephone.

Settings.

1. Volume.

See the "Audio and telematics"

section.

Allows configuration of the display

and the system.

Language, units, date and time,

colour schemes, ...

2. On / Off.

3. Black panel (comfortable night driving

display).

4. Change audio source.

5. Access to audio settings.

See the "Audio and telematics" section.

connected services.

The connected services are

accessible via Bluetooth, Wi-Fi,

MirrorLink™ or CarPlay^®connections.

See the "Audio and telematics"

section.

45

Monitoring

"driving" menu

The systems with settings that can be adjusted are detailed in the table below.

Button

corresponding function

Speed settings

comments

Memorisation of speeds for use with the speed limiter or cruise control.

vehicle settings

Access to other functions with settings that can be adjusted:

-

Automatic parking brake (Automatic electric parking brake; see the "Driving" section),

Automatic rear wiper in reverse (Activation of rear wiper coupled to reverse gear; see the

"Visibility" section).

-

Guide-me-home lighting (Automatic guide me home lighting; see the "Visibility" section),

Welcome lighting (Exterior welcome lighting; see the "Visibility" section),

Mood lighting (Mood lighting; see the "Visibility" section),

Adaptive lighting (Main / additional directional lighting; see the "Visibility" section).

Driver plip action (Selective unlocking of the driver's door; see the "Access" section),

Unlocking boot (Selective unlocking of the boot; see the "Access" section).

Stop & Start

Deactivation of the function.

Function deactivated = indicator lamp on (orange).

Trip computer

System that gives you information on the current journey (range, fuel consumption…).

Instrument panel screen

-

The current information tab with:

● the range,

Trip reset

● the current fuel consumption,

● the Stop & Start time counter.

-

Trip "1" with:

● the average speed,

● the average fuel consumption

for the first trip.

F

When the desired trip is displayed, press

for more than two seconds on the end of

the wiper control stalk.

Trips "1" and "2" are independent but their use

is identical.

For example, trip "1" can be used for daily

figures, and trip "2" for monthly figures.

Trip "2" with:

● the average speed,

● the average fuel consumption

for the second trip.

Information display

F

Press the button on the end of the wiper

control stalk to display the various tabs in

succession.

-

Radio or media.

Satellite navigation.

47

Monitoring

Touch screen

display of information

Trip reset

F

Select the "driving" menu.

The trip computer information is displayed in

the primary page of the menu.

F

Press one of the buttons to display the

desired tab.

The current instantaneous fuel consumption tab with:

F

When the desired trip is

-

the range,

the current fuel consumption,

the Stop & Start time counter.

displayed, press the reset button

or press and hold the end of the

wiper control stalk.

1. "Instantaneous".

2. "Trip 1".

3. "Trip 2".

4. "00.0 / Reset".

The trip "1" tab with:

Trips "1" and "2" are independent but their use

is identical.

For example, trip "1" can be used for daily

figures, and trip "2" for monthly figures.

-

the average speed,

the average fuel consumption,

for the first trip.

The trip "2" tab with:

-

the average speed,

the average fuel consumption,

for the second trip.

Trip computer, a few definitions…

Range

current fuel consumption

Average speed

(miles or km)

(mpg or l/100 km or km/l)

(mph or km/h)

This indicates the distance which

can still be travelled with the fuel

remaining in the tank in relation

to the average fuel consumption

over the last few miles

This is the average fuel consumption

during the last few seconds.

This is the average speed calculated

since the last trip computer zero

reset (ignition on).

(kilometres) travelled.

Stop & Start time

counter

This function is only displayed from

20 mph (30 km/h).

(minutes / seconds or hours /

minutes)

This value may vary following a change

in the style of driving or the relief,

resulting in a significant change in the

current fuel consumption.

If your vehicle is fitted with Stop & Start,

a time counter calculates the time spent in

STOP mode during a journey.

It resets to zero every time the ignition is

switched on.

Average fuel

consumption

(mpg or l/100 km or km/l)

This is the average fuel

consumption since the last trip

computer zero reset.

When the range falls below 20 miles (30 km),

dashes are displayed. After filling with at least

5 litres of fuel, the range is recalculated and is

displayed when it exceeds 60 miles (100 km).

If dashes are displayed continuously

while driving in place of the digits,

contact a CITROËN dealer or

a qualified workshop.

49

Monitoring

Instruments and controls for Your Citroen Ds5 SUV First Generation (2011-2018)

Related Topics

Popular Owner Manuals

Latest Owner Manuals