Get AUDIO and TELEMATICS Guide for DS 5 4 Door First Generation (2011-2018)

Audio and telematics

Emergency or assistance call

Localised Emergency call

In an emergency, press this

button for more than 2 seconds.

Flashing of the green LED and

a voice message confirm that

the call has been made to the

"Localised Emergency Call"*

centre.

If an impact is detected by the airbag

control unit, and independently of

the deployment of any airbags, an

emergency call is made automatically.

Pressing this button again immediately cancels

the call.

The green LED goes off.

Pressing this button (at any time) for more than

8 seconds cancels the call.

If you benefit from the DS Connect

BOX offer with the SOS and assistance

pack included, you also have

available additional services in your

MyCITROËN personal space,

via the CITROËN Internet website in

your country, accessible on

The green LED remains on (without flashing)

when communication is established.

It goes off at the end of the call.

This call is dealt with by the "Localised

Emergency Call", which receives locating

information from the vehicle and can send a

detailed alert to the appropriate emergency

services.

In countries in which a centre is not

operational, or when the locating service

has been expressly declined, the call is dealt

with directly by the emergency services (112)

without the vehicle location.

* These services are subject to conditions and

availability.

Consult a CITROËN dealer.

283

Audio and Telematics

Localised Assistance call

Press this button for more than

2 seconds to request assistance

if the vehicle breaks down.

A voice message confirms that

the call has been started*.

Operation of the system

When the ignition is switched

If you purchased your vehicle outside

on, the green LED comes on for

3 seconds indicating that the

system is operating correctly.

the CITROËN dealer network, we

invite you to have a dealer check the

configuration of these services and, if

desired, modified to suit your wishes.

In a multi-lingual country, configuration

is possible in the official national

language of your choice.

Pressing this button again immediately cancels

the request.

The cancellation is confirmed by a voice

message.

If the orange LED flashes: there

is a system fault.

If the orange LED is on continuously: the

backup battery must be replaced.

In either case, contact a CITROËN dealer.

For technical reasons, particularly

to improve the quality of Telematic

services to customers, the

manufacturer reserves the right to

carry out updates to the vehicle's on-

board telematic system.

* These services are subject to conditions and

availability.

Consult a CITROËN dealer.

285

Audio and Telematics

7-inch touch screen tablet

g PS satellite navigation - Multimedia audio - Bluetooth^®telephone

Contents

286

First steps

Steering mounted controls

288

Menus

289

Navigation

Navigation - Guidance

Trafﬁc

290

298

302

Radio Media

Radio

304

310

DAB (Digital Audio Broadcasting) radio

312

314

318

326

327

330

332

340

Media

Settings

Internet

Internet browser

MirrorLink^®

Telephone

Frequently asked questions

As a safety measure, the driver should only carry out operations

which require prolonged attention while the vehicle is stationary.

The display of the energy economy mode message signals

that the system is about to go into standby. Refer to the Energy

economy (mode) section.

The system is protected in such a way that it will only operate in

your vehicle.

First steps

Use the buttons below the touch screen tablet

for access to the menus, then press the virtual

buttons in the touch screen tablet.

Each menu is displayed in one or two pages

(primary page and secondary page).

In very hot conditions, the system may

go into stand-by (screen and sound

completely off) for a minimum period of

5 minutes.

Primary page

Secondary page

287

Audio and Telematics

Short-cuts: using the virtual buttons in the

upper band of the touch screen tablet, it is

possible to go directly to the selection of audio

source, the list of stations (or titles, depending

on the source).

The screen is of the "resistive" type, it

is necessary to press firmly, particularly

for "flick" gestures (scrolling through a

list, moving the map...). A simple wipe

will not be enough. Pressing with more

than one finger is not recognised.

The screen can be used when wearing

gloves. This technology allows use at

all temperatures.

With the engine running, press to

mute the sound.

With the ignition off, press to switch

the system on.

Selecting the audio source (depending on

version):

To clean the screen, use a soft

non-abrasive cloth (spectacles cloth)

without any additional product.

Do not use pointed objects on the

screen.

-

"FM" / "AM" / "DAB"* stations.

"USB" memory stick.

Volume adjustment (each source

is independent, including traffic

announcements (TA) and navigation

instructions).

CD player (located in front panel).

Jukebox*, after first copying audio files to

the internal memory of the system.

Telephone connected by Bluetooth* and

using Bluetooth* audio streaming.

Media player connected to the auxiliary

socket (jack, cable not supplied).

Do not touch the screen with wet

hands.

-

In very hot conditions, the volume may

be limited to protect the system. The

return to normal takes place when

the temperature in the passenger

compartment drops.

AM and DAB are not available on Hybrid

vehicles.

* Depending on equipment.

Steering mounted controls

Media: change the multimedia

source.

Telephone: call.

Radio: display the list of stations.

Media: display the list of tracks.

Radio, press and hold: update the list

of stations received.

Call in progress: access to the

telephone menu (end call, secret

mode, hands-free mode).

Telephone, press and hold: reject an

incoming call, end a call; when there

is no call in progress, access to the

telephone menu.

MirrorLink^®, press and hold:

start voice recognition on your

smartphone via the system.

Increase volume.

Decrease volume.

Radio, rotate: automatic search for

the previous / next station.

Media, rotate: previous / next track.

Press: confirm a selection.

289

Audio and Telematics

Menus

navigation

Settings

Radio Media

(Depending on equipment)

Select radio, the different music sources and

view photos.

Set the sounds and brightness for the

instruments and controls.

Enter navigation settings and choose a

destination.

Internet

Telephone

driving

(Depending on equipment)

Connect a telephone by Bluetooth^®.

Access the trip computer, activate, deactivate

or enter settings for certain vehicle functions.

Connect using the "Internet browser".

Operate certain applications on your

smartphone via "MirrorLink".

Navigation

Level 1

Level 2

Level 3

navigation

Route settings

1

291

Audio and Telematics

Level 1

Level 2

Level 3

c omments

Display recent destinations

Enter destination

Fastest

Shortest

Time/distance

Ecological

Tolls

Choose the navigation criteria.

The map displays the route chosen according to

these criteria.

c alculatory criteria

Ferries

navigation

Traffic

Settings

navigation

Strict-Close

Show route on map

Confirm

Display the map and start navigation.

Save the options.

Save current location

Stop navigation

Save the current address.

Delete the navigation information.

Choose the volume for voice and announcement

of street names.

Voice synthesis

diversion

Detour from your initial route by a determined

distance.

Display in text mode.

Zoom in.

Zoom out.

navigation

Display in full screen mode.

Use the arrows to move the map.

Switch to 2D map.

Level 1

Level 2

Level 3

Address

Enter destination

1

2

3

4

5

6

7

8

9

10 11

For managing contacts and

their addresses, refer to the

"Telephone" section.

navigation

c ontacts

12 13 14 15

To use the telephone functions,

refer to the "Telephone" section.

293

Audio and Telematics

Level 1

Level 2

Level 3

c omments

Curr. location

7

8

Points of Interest

Town centre

Save

Address settings.

9

Address

2

Save the current address.

Add a waypoint to the route.

Press to calculate the route.

10

11

Add waypoint

Navigate to

Addresses

View

12

13

14

15

navigation

Secondary page

Enter destination

1

c ontacts

Navigate to

Search for contact

Call

Select a contact then calculate the route.

Display the map and zoom to view the roads.

3

4

From map

Itinerary

Create, add or delete a waypoint or view the

itinerary.

5

6

Stop

Delete navigation information.

Press to calculate the route.

navigate to

Level 1

Level 2

Level 3

1

navigation

Search for a point of interest

16 17 18 19

Point of interest displayed on the map

20

21

22

295

Audio and Telematics

Level 1

Level 2

All POIs

Level 3

c omments

16

17

18

19

navigation

Secondary page

Search for POI

List of categories available.

After choosing the category, select the points of

interest.

g arage

dining/hotels

Personal

Search

1

Save the settings.

Select all

delete

20

21

22

navigation

Secondary page

Show POIs

Choose the display settings for POIs.

Save the options.

Import POIs

c onfirm

Level 1

Level 2

Level 3

diversion

Traffic messages

1

Map settings

23 24 25 26

Map settings

navigation

27

28

29

Settings

27

28

29

Settings

30 31 32 33

Moving

between

the two

menus.

Settings

30 31 32 33

297

Audio and Telematics

Level 1

Level 2

Level 3

c omments

On the route

23

24

25

Around vehicle

near destination

navigation

Settings for the choice of messages and the

filter radius.

Secondary page

Traffic messages

1

Detour over a distance

detour

Finish

26

Recalculate route

Save your selections.

Flat view north heading

Flat view vehicle heading

Perspective view

Orientation

Maps

27

28

29

navigation

Secondary page

Map settings

Choose the display and orientation of the map.

1

"Day" map colour

"Night" map colour

Automatic day/night

Aspect

c onfirm

Save the settings.

Route settings

Voice

30

31

32

33

navigation

Secondary page

Settings

Enter settings and choose the volume for the

voice and announcement of street names.

Alert!

1

Traffic options

c onfirm

Save your selections.

Navigation - Guidance

choosing a new destination

Towards a new destination

Press on navigation to display the

primary page.

Select "Save" to save the address

entered as a contact entry.

The system allows up to 200 entries.

To delete navigation information, press

"Settings".

10

Press on the secondary page.

Press "Stop navigation".

1

Select "navigate to".

Select "Enter destination".

To resume navigation press "Settings".

Press "Resume navigation".

Choose the navigation criteria:

"Fastest" or "Shortest" or "Time/

distance" or "Ecological".

Select "Address".

2

Select the "c ountry:" from the

list offered, then in the same

way the "c ity:" or its post

code, the "Road:", the "n°:".

Confirm each time.

Choose the restriction criteria:

"Include tollroads", "Include

ferries", "Traffic", "Strict", "c lose".

Select "c onfirm".

Or

Press "Show route on map" to start

navigation.

299

Audio and Telematics

Towards a recent destination

Towards a contact

Press on navigation to display the

primary page.

Select a destination from

the contacts in the list

offered.

To be able to use navigation "towards

a contact in the directory", it is first

necessary to enter the address for your

contact.

Press on the secondary page.

Select "navigate to".

1

Press on navigation to display the

primary page.

Select "Enter destination".

Select the criteria then "c onfirm" to

start navigation.

Press on the secondary page.

1

Select an address from

the list offered.

Select "Enter destination".

Select "navigate to".

Select "c ontacts".

3

Select the criteria then "c onfirm" or

press "Show route on map" to start

navigation.

Towards g PS coordinates

Towards a point on the map

Towards points of interest (POI)

Press on navigation to display the

primary page.

Press on navigation to display the

primary page.

Points of Interest (POI) are listed in different

categories.

Press on the secondary page.

Press on navigation to display the

primary page.

1

Select "Enter destination".

Press on the secondary page.

1

Select "Address".

Select "From map".

Select "Search for POI".

2

4

Enter the "Longitude:"

then the "Latitude:".

Zooming in on the map shows points with

Select "All POIs"

information.

16

A long press on a point opens its content.

Or

Select "navigate to".

"g arage",

17

Select the criteria then "c onfirm" or

press "Show route on map" to start

navigation.

Or

"dining/hotels",

18

301

Audio and Telematics

Or

An annual mapping update allows new

points of interest to be presented to

you.

You can also update the Risk areas /

Danger areas every month.

The detailed procedure is available on:

"Personal",

19

Select a category from the

list offered.

Select "Search".

Select a point of interest

from the list offered.

Select "navigate to".

Trafﬁc

Hazard zone / danger zone

alert settings

Traffic information

display of messages

Press on navigation to display the

primary page.

This series of alerts and displays is

only available if Risk Areas have first

been downloaded and installed on the

system.

Press on the secondary page.

1

Select "Traffic messages".

Select "Settings".

Set the:

23

24

25

Select "Alarm!".

"On the route",

"Around",

32

It is then possible to activate Risk Areas alerts

then:

-

"Audible warning"

"Alert only when navigating"

"Alert only for overspeed"

"Display speed limits"

Timing: the choice of timing allows the

time before giving a Risk Area alert to be

defined.

"near destination", filters to fine-

tune the list of messages.

Press again to remove the filter.

Select "c onfirm".

303

Audio and Telematics

Setting ﬁlters

Receiving TA messages

Select the message from

the list offered.

Press on navigation to display the

primary page.

Press on navigation to display the

primary page.

Press on the secondary page.

Select the magnifying glasses to

have vocal information.

1

Select "Settings".

Select "Voice".

TMC (Traffic Message Channel)

messages on GPS-Navigation contain

traffic information transmitted in real

time.

Select "Info options".

33

31

Select:

Activate / Deactivate "Traffic

(TA)".

-

"Warn of new messages",

"Speak messages".

The TA (Traffic Announcement)

function gives priority to TA alert

messages. To operate, this function

needs good reception of a radio station

transmitting this type of message.

When a traffic report is transmitted,

the current audio source is interrupted

automatically to play the TA message.

Normal playback of the audio source

resumes at the end of the transmission

of the message.

Then enter the filter radius.

Select "c onfirm".

We recommend a filter radius of:

-

12 miles (20 km) in urban areas,

30 miles (50 km) on motorways.

Radio Media

Level 1

Level 2

List of FM stations

1

2

3

4

Preset

305

Audio and Telematics

Level 1

Level 2

c omments

Radio Media

List of FM stations

Press on a radio station to select it.

List

FM Radio

dAB Radio

AM Radio

Jukebox

cd

Radio Media

Source

Select change of source.

USB

3

MirrorLink

iPod

Bluetooth

AUX

Radio Media

Preset

Press an empty location to Preset it.

2

Level 1

Level 2

Level 3

List of FM stations

1

5

6

7

Media

Photos

8

9

10 11

c opy to Jukebox

Manage Jukebox

12

13

14

15 16 17 18

307

Audio and Telematics

Level 1

Level 2

Preset

Level 3

c omments

Press a radio station to select it.

Update the list of stations received.

Enter the desired radio frequency.

Save the settings.

5

6

7

Radio Media

Update list

Frequency

c onfirm

Secondary page

Radio list

1

Home screen

Rotate

Display the selected photo in the home page.

Rotate the photo 90°.

8

9

Select all the photos in the list.

Press again to deselect.

Radio Media

Secondary page

Photos

Select all

10

Previous photo.

Pause / Play.

Next photo.

Display the photos in sequence, full screen.

The system supports the following image

formats: .gif, .jpg, .bmp, .png.

11 Slideshow

Full screen

Display the selected photo full-screen.

Choose a selection mode.

Sort by folder

12

Sort by album

13

Select all

14

Radio Media

Secondary page

Manage Jukebox

c opy

Copy files to the Jukebox.

Create folder

Rename

Delete

15

16

17

18

1

Choose the desired function.

Save the settings.

Magnifying glass

Select all

Confirm

Level 1

Level 2

Level 3

1

Media

Settings

19

20

21

Settings

19

20

21

20

309

Audio and Telematics

Level 1

Level 2

Level 3

c omments

Radio Media

Secondary page

Media list

Presentation of the last media used.

1

Random (all tracks):

Media

Random (current album):

Choose the play settings.

19

Settings

Loop:

Aux. amplification

RDS options

Radio Media

Secondary page

Settings

DAB/FM options

Display Radio Text

Radio

Activate or deactivate the settings.

20

21

1

Settings

Digital radio slideshow

display

Traffic announcements (TA)

News - Weather

Announcements

Settings

Activate or deactivate the settings.

Save the settings.

Sport - Programm info

Flash - Unforeseen

events

c onfirm

Radio

Selecting a station

changing a radio frequency

Press on Radio Media to display the

primary page.

Press on Radio Media to display the

primary page.

Select "Preset".

2

3

Or

Select a preset radio station

in the list.

Press on Radio Media to display the

primary page.

If necessary, select change of

source.

By automatic frequency search

Press on the secondary page.

Select "FM Radio".

1

3

Press 3 or 4 to move the cursor for an

automatic search down or up for a radio

frequency.

Select "List" in the primary page.

Or

"AM Radio".

THEn

Select "Radio list" in the secondary

page.

Select change source.

Radio reception may be affected by

the use of electrical equipment not

approved by CITROËN, such as a USB

charger connected to the 12 V socket.

The exterior environment (hills,

buildings, tunnel, car park, below

ground...) may prevent reception,

even in RDS station tracking mode.

This phenomenon is normal in the

propagation of radio waves and is in no

way indicative of a fault with the audio

system.

Select a radio station from

the list offered.

3

Select "FM Radio".

Select "Update list" to refresh the

list.

Or

"AM Radio".

OR

Press Radio Media to display the

primary page.

311

Audio and Telematics

Preset a station

Activate/ deactivate RdS

OR

Select a radio station or frequency (refer to the

corresponding section).

Press on Radio Media to display the

primary page.

Press on Radio Media to display the

primary page.

Press on "Preset".

Press on the secondary page.

5

1

Press on the secondary page.

Select "Settings".

1

Select a number in the list to preset the

previously chosen radio station.

A long press on a number presets (memorises)

the station.

Press on Frequency.

Select "Radio".

7

20

Activate/deactivate "RdS

options".

Or

THEn

A press on this button presets all of

the stations one after the other.

Enter the frequency in full

(e.g.: 92.10 MHz) using the keypad

then "c onfirm".

4

RDS, if activated, allows you to continue

listening to the same station by automatic

retuning to alternative frequencies.

However, in certain conditions, coverage

of an RDS station may not be assured

throughout the entire country as radio

stations do not cover 100 % of the

Recall pre-set stations

Press on Radio Media to display the

primary page.

c hanging radio station

Pressing the name of the current radio station

brings up a list.

To change radio station press the name of the

desired station.

Select "Save".

territory. This explains the loss of

reception of the station during a journey.

2

DAB (Digital Audio Broadcasting) radio

Short-cut: access to the choice of audio

Display of the name of the

current station.

source and the list of stations (or titles,

depending on the source).

Select the radio station.

Any thumbnail broadcast by

the station.

Manage the Jukebox.

Display current action.

Display the name and

number of the multiplex

service being used.

Display of "Radiotext" for

the current station.

Previous "Multiplex".

Previous radio station.

Next "Multiplex".

Next radio station.

Preset stations, buttons 1

to 15.

Short press: select the

preset radio station.

Long press: preset a radio

station.

Select the audio source.

Display the "DAB" band.

Secondary page.

Display of options:

If the "DAB" radio station being listened to is not

available on "FM", the "DAB FM" option is greyed out.

if active but not available, the display will be greyed out,

if active and available, the display will be blank.

Journaline^®is a text-based information service designed for digital radio systems.

It provides text-based information structured around topics and sub-topics.

This service is available from the "LIST OF DAB STATIONS" page.

313

Audio and Telematics

digital radio

dAB / FM auto tracking

Digital radio provides higher quality

"DAB" does not cover 100% of the

territory.

If "DAB / FM auto tracking" is activated,

there is a difference of a few seconds

when the system switches to "FM"

analogue radio with sometimes a

variation in volume.

When the digital signal is restored,

the system automatically changes back

to "DAB".

reception and also the graphical display

of current information on the radio

station being listened to. Select "List" in

the primary page.

The range of multiplexes available is

displayed in alphabetical order.

When the digital radio signal is poor,

"DAB / FM auto tracking" allows you to

continue listening to the same station,

by automatically switching to the

corresponding "FM" analogue station

(if there is one).

Press on Radio Media to display the

primary page.

Press on Radio Media to display the

primary page.

If the "DAB" station being listened to

is not available on "FM" ("dAB/FM"

option greyed out), or "DAB / FM auto

tracking" is not activated, the sound

will cut out while the digital signal is too

weak.

Select change of source.

Select "dAB Radio".

Press on the secondary page.

3

1

Select "Settings".

Select "List" in the primary page.

Select "RAdIO".

20

or

Select "Radio list" in the secondary

page.

Select "digital/FM auto

tracking" then "c onfirm".

Select the radio station from the list offered.

Media

USB player

Auxiliary socket (AUX)

Selection of source

Press on Media to display the

primary page.

Select change of source.

3

Insert the USB memory stick into the USB port

or connect the USB device to the USB port

using a suitable cable (not supplied).

Connect the portable device (MP3 player…) to

the auxiliary Jack socket using an audio cable

(not supplied).

The system builds playlists (in temporary

memory), an operation which can take from

a few seconds to several minutes at the first

connection.

Reduce the number of non-music files and the

number of folders to reduce the waiting time.

The playlists are updated every time the

ignition is switched off or connection of a USB

memory stick. The lists are memorised: if they

are not modified, the subsequent loading time

will be shorter.

First adjust the volume of your portable device

(to a high level). Then adjust the volume of your

audio system.

Display and management of the controls are

via the portable device.

Choose the source.

The steering mounted SRc (source)

button can be used to go to the next

media source, available if the source

is active.

cd player

Insert the CD in the player.

Press OK to confirm the selection.

315

Audio and Telematics

Information and advice

The audio equipment will only play audio

files with ".wma, .aac, .flac, .ogg and .mp3"

file extensions and with a bit rate of between

32 Kbps and 320 Kbps.

It also supports VBR (Variable Bit Rate) mode.

No other type of file (.mp4, ...) can be played.

"wma" files must be of the standard

wma 9 type.

In order to be able to play a recorded CDR or

CDRW, when recording it is preferable to select

the ISO 9660 level 1, 2 or Joliet standard.

If the disc is recorded in another format it may

not be played correctly.

It is recommended that the same recording

standard is always used for an individual disc,

with as low a speed as possible (4x maximum)

for optimum sound quality.

Use only USB memory sticks formatted FAT 32

(28-bit file allocation table).

The system does not support the

simultaneous connection of two

identical devices (two memory sticks,

two Apple^®

players) but it is possible

The sampling rates supported are 11, 22, 44

and 48 KHz.

to connect one memory stick and one

Apple^®player at the same time.

In the particular case of a multi-session CD, the

Joliet standard is recommended.

It is recommended that the USB cable

for the portable device is used.

It is advisable to restrict file names to

20 characters, without using of special

characters (e.g.: " " ? ; ù) to avoid any playing

and displaying problems.

The system supports USB mass

storage devices, BlackBerry^®devices

or Apple^®players via USB ports. The

adaptor cable not supplied.

Control of the peripheral device is with

the audio system controls.

Other peripherals, not recognised on

connection, must be connected to the

auxiliary socket using a Jack cable (not

supplied).

Bluetooth^®audio streaming connecting Apple^®players

Streaming allows audio files on your telephone

to be played through the vehicle's speakers.

The classifications available are those

of the portable device connected

(artists / albums / genres / playlists /

audiobooks / podcasts).

The default classification used is by

artist. To modify the classification used,

return to the first level of the menu

then select the desired classification

(playlists for example) and confirm

to go down through the menu to the

desired track.

Connect the telephone: see the "Telephone"

section, then "Bluetooth".

Choose the "Audio" or "All" profile.

If play does not start automatically, it may be

necessary to start the audio playback from the

telephone.

Control is from the peripheral device or by

Play starts automatically.

using the audio system buttons.

Connect the Apple^®player to the USB port

using a suitable cable (not supplied).

Control is via the audio system.

The version of software in the audio system

may not be compatible with the generation of

your Apple^®player.

Once connected in streaming mode,

the telephone is considered to be a

media source.

It is recommended that you activate

"Repeat" on the Bluetooth peripheral.

317

Audio and Telematics

Managing the Jukebox

Connect the device (MP3 player...) to the USB

port or auxiliary Jack socket using a suitable

audio cable.

Select the magnifying glass to enter

the folder or album and select audio

file by audio file.

Select "c onfirm" then "c opy".

When no audio file is copied to the

system, which has a capacity of 8 GB,

all of the Jukebox function symbols are

greyed and are not available.

Select "new folder" to create a

folder structure in the Jukebox.

15

Select "Media list".

Or

Select "Keep structure" to retain the structure

from the device.

Select copy "c opy Jukebox".

While copying the system returns to the

primary page; you can go back to the copy view

at any time by selecting this button.

Select "Sort by folder".

12

Or

"Sort by album".

13

Settings

Level 1

Level 2

Level 3

Audio settings

3

4

5

6

7

3

4

5

6

7

Audio settings

1

2

3

4

5

6

7

319

Audio and Telematics

Level 1

Level 2

Ambience

Level 3

c omments

Choose the sound ambience.

3

4

Balance

Sound distribution using the Arkamys^®system.

Set the volume or activate the link to vehicle

speed.

Sound effects

Ringtones

5

6

7

Settings

Audio settings

Set the telephone ringtone and volume.

Set the volume and voice for speaking street

names.

Voice

c onfirm

Save your settings.

Settings

Function that turns off the display.

Pressing the screen reactivates it.

2

Turn off screen

Level 1

Level 2

Units

1

Factory settings

8

9

10

c onfiguration

Adjust date and time

8

9

10

display screen

321

Audio and Telematics

Level 1

Level 2

c omments

Set the units used to display distance, fuel

consumption and temperature.

Units

8

9

Settings

Select the desired data in the list then press

Delete.

delete data

Factory settings

c onfirm

Secondary page

System Settings

1

Return to factory settings.

Save the settings.

10

Settings

Secondary page

Time/date

c onfirm

Set the date and time then confirm.

1

Activate automatic text scrolling

Activate animations

c onfirm

Settings

Secondary page

Screen settings

Activate or deactivate the setting then confirm.

Level 1

Level 2

c hoice of language

1

c onfiguration

c alculator

c alendar

323

Audio and Telematics

Level 1

Level 2

c omments

Settings

Secondary page

Languages

c onfirm

Select the language then confirm.

1

Settings

Secondary page

c alculator

Select the calculator.

Settings

Secondary page

c alendar

Select the calendar.

1

Audio settings

Press Settings to display the primary

page.

On-board audio: Arkamys^©Sound

Staging optimises sound distribution in

the the passenger compartment.

The distribution (or spatialisation using

the Arkamys^®system) of sound is an

audio process that allows the audio

quality to be adapted to the number of

passengers in the vehicle.

Select "Audio settings".

Available only with the 6-speaker

configuration.

Select "Ambience"

"Balance"

3

4

5

6

The audio settings (Ambience, Bass,

Treble and Loudness) are different

and independent for each sound

source.

Or

The settings for F-R balance and

L-R balance are common to all

sources.

"Sound effects"

"Ringtones"

-

"Ambience" (choice of 6 musical

ambiences)

-

"Bass"

"Treble"

"Loudness" (Activate/Deactivate)

"Balance" ("driver", "All

passengers", "Front only")

"Audible response from touch screen"

"Volume linked to vehicle

speed:" (Activate/Deactivate)

Or

"Voice".

-

7

325

Audio and Telematics

Modifying system settings

Press on Settings to display the

Press on "Settings" to display the

primary page.

Press on the secondary page.

1

Select "System Settings".

Select "Screen settings".

Select "Time/date" to change the

time zone, synchronisation with GPS,

the time and its format, then the date.

Select "Units" to change the units

of distance, fuel consumption and

temperature.

Activate or deactivate "Activate

automatic text scrolling" and

"Activate animations".

Select "Languages" to change

language.

8

Select "delete data" to delete the

list of recent destinations, personal

9

Select "c alculator" to display a

calculator.

points of interest, contacts in the list.

Select "c alendar" to display a

Choose the item then select "delete".

calendar.

Select "Factory settings" to return

to the original settings.

10

Internet

Level 1

Level 2

Level 3

1

327

Audio and Telematics

Internet browser

Press on Internet to display the

primary page.

Press on "Internet browser" to

displays the browser's home page;

first connect your smartphone by

Bluetooth, option "Internet", see the

"Telephone" section.

Authentication for Internet browsing via

a smartphone is done using the Dial-Up

Networking (DUN) standard.

Some smartphones of the latest

generation do not support this

standard.

Level 1

Level 2

Level 3

Bluetooth (devices)

1

2

3

4

5

Usage monitor

Internet

Wi-Fi network connection

6

7

8

9

10 11

329

Audio and Telematics

Level 1

Level 2

Search

Level 3

c omments

Start the search for a device to connect.

2

3

Start or end the Bluetooth connection to the

selected device.

Internet

c onnect / disconnect

Update

Secondary page

Import contacts from the selected telephone to

save them in the audio system.

1

4

5

Bluetooth

c onnection

delete

Delete the selected telephone.

Save the settings.

c onfirm

Internet

Reset

Secondary page

Transfer rate

Reset the usage monitor, them confirm.

c onfirm

All

Display all Wi-Fi networks.

6

7

Secure

Display secure Wi-Fi networks.

Memorise the selected Wi-Fi network(s).

Add a new Wi-Fi network.

Internet

Stored

8

Secondary page

WiFi connection

1

Add

9

Activate / deactivate

c onnect

Activate or deactivate a Wi-Fi network.

10

11

Select a Wi-Fi network found by the system and

connect to it.

MirrorLink^®

331

Audio and Telematics

Press "MirrorLink^®" to start

the application in the system.

MirrorLink^®smartphone

connection

Please note:

-

if your mobile is supported, to make

it "MirrorLink^®" compatible, some

phone manufacturers nevertheless

invite you to first download a

dedicated application.

As a safety measure and because it

requires sustained attention by the

driver, using a smartphone when

driving is prohibited.

All operations must be done with the

vehicle stationary.

Start the application on the

smartphone.

-

iPhone^®is not supported yet; an

Apple^®application, "CarPlay^®", is

being developed.

During the procedure, a page

showing the conditions for use is

displayed.

Accept to start and end the

connection.

The synchronisation of a personal

smartphone allows applications on a

smartphone that are adapted to the

MirrorLink^®technology to be displayed

in the vehicle's screen.

As a safety measure, applications

can only be viewed with the vehicle

stationary; display is interrupted once

the vehicle is moving.

The "Audio source" and "Telephone"

functions remain available in the margin of the

MirrorLink^®display.

The principles and standards are

constantly evolving; for information

on supported smartphones, go to the

CITROËN website for your country.

Select MyCITROËN if present.

Go to the home page to return to the

"MirrorLink^®" display.

When connecting a smartphone to

the system, it is recommended that

Bluetooth^®be started on the smartphone

Voice recognition

and

a USB cable is connected. The

smartphone charges when

connected by a USB cable.

Press the end of the lighting control stalk to

start voice recognition of your smartphone via

the system.

Voice recognition requires a compatible

telephone connected to the vehicle by

Bluetooth.

From the system, press "Internet" to

display the primary page.

Telephone

Level 1

Level 2

c all log

Level 3

4

5

6

7

12

13

c ontacts

1

2

3

8

9

10 11

14 15 16 17 18

333

Audio and Telematics

Level 1

Level 2

All calls

Level 3

c omments

4

5

6

7

Incoming calls

Outgoing calls

c ontacts

Telephone

c all log

After making choices, start the call.

2

View

12

13

Magnifying glass

Create

c all

Addresses

8

9

New

14

15

16

17

18

Modify

Delete

View

Telephone

c ontacts

Delete all

Search for contact

Confirm

After making choices, start the call.

3

navigate to

Search for contact

c all

10

11

Level 1

Level 2

Level 3

Bluetooth (devices)

1

19 20 21 22

devices detected

Telephone connection

Telephone Options

23 24 25 26

335

Audio and Telematics

Level 1

Level 2

Search

Level 3

c omments

Start the search for another peripheral device to

connect.

19

20

Telephone

connection

Start or stop the Bluetooth connection to the

selected peripheral device.

c onnect disconnect

Update

Secondary page

Import the contacts from the selected telephone

to store them in the audio system.

1

21

22

Bluetooth

c onnection

delete

Delete the selected telephone.

Save the settings.

c onfirm

Telephone

connection

Telephone

Secondary page

devices detected

Audio streaming

Start the search for peripheral devices.

Search for

devices

Internet

Cut the microphone temporarily so that the

contact cannot hear your conversation with a

passenger.

Put on hold

23

Import the contacts from the selected telephone

to save then in the audio system.

Telephone

connection

Update

24

25

1

Ringtones

Choose the telephone ringtone and volume.

Secondary page

Contact records used and free, percentage of

storage space used by internal contacts and

Bluetooth contacts.

Telephone options

Memory info.

c onfirm

26

Save the settings.

Pairing a Bluetooth^®

telephone

Procedure from the system

For reasons of safety and because they

require prolonged attention on the part

of the driver, the operations for pairing

the Bluetooth mobile telephone to the

hands-free system of the audio system

must be carried out with the vehicle

stationary.

Activate the telephone's Bluetooth function

and ensure that it is "visible to all" (telephone

configuration).

Select the name of the

desired peripheral from the

list and "c onfirm".

Press on Telephone to display the

primary page.

Enter a code of at least 4 figures for

the connection then "c onfirm".

Procedure (short) from the

telephone

Press on the secondary page.

Enter this same code in the telephone then

accept the connection.

1

In the Bluetooth menu of your device, select the

system name in the list of devices detected.

Select "Bluetooth connection".

Select Search.

The list of telephones detected is

displayed.

The system offers to connect the telephone:

-

in "Telephone" (hands-free kit, telephone

only),

Enter a code of at least 4 figures in the device

and confirm.

in "Audio streaming" (streaming: wireless

playing of audio files from the telephone),

in "Internet" (internet browsing, only if your

telephone is compatible with the "DUN"

Dial-Up Networking Bluetooth standard).

Enter this same code in the system,

select "OK" and confirm.

19

Select one or more profiles and confirm.

If the telephone is not detected, it is

recommended that you switch the Bluetooth

function on your telephone off and then on again.

337

Audio and Telematics

connecting a Bluetooth^®

peripheral device

Automatic reconnection

On switching on the ignition, the telephone

connected when the ignition was last switched

off is automatically reconnected, if this

connection mode had been activated during the

pairing procedure.

The services available depend on

the network, the SIM card and the

compatibility of the Bluetooth telephone

used. Check the telephone manual and

with your network provider for details of

the services available to you.

Depending on the type of telephone,

the system will ask you to accept or not

the transfer of your contacts.

If not, select "Update".

The connection is confirmed by the display of a

message and the name of the telephone.

Manual connection

On return to the vehicle, if the last telephone

connected is present again, it is reconnected

automatically and within around 30 seconds

after switching on the ignition the pairing is

done without any action on your part, with

(Bluetooth activated).

To modify the automatic connection mode,

select the telephone in the list then select the

desired profile.

The ability of the system to connect

with only one profile depends on the

telephone. The two profiles may both

connect by default.

Press on Telephone to display the

primary page.

Press on the secondary page.

1

Visit

(compatibility, additional help, ...).

Select "Bluetooth" to display the list

of paired peripherals.

The recognised telephone

appears in the list.

Select the peripheral to connect.

Press on "Search".

19

Depending on your telephone, you may be

asked to accept automatic connection every

time the ignition is switched on.

The connection is confirmed by the display of a

message and the name of the telephone.

Managing paired

telephones

Receiving a call

Making a call

An incoming call is announced by a ring and a

superimposed display in the screen.

Using the telephone is not

recommended while driving.

Park the vehicle.

Make the call using the steering

mounted controls.

This function allows the connection or

disconnection of a peripheral device as

well as the deletion of a pairing.

Make a short press on the steering

mounted TEL button to accept an

incoming call.

Press on Telephone to display the

primary page.

Make a long press

c alling a new number

Press on the secondary page.

Press on Telephone to display the

primary page.

1

on the steering mounted TEL button

to reject the call.

Select "Bluetooth" to display the list

of paired peripheral devices.

Enter the phone number using the

digital keypad.

Press "c all" to start the call.

Or

Select the peripheral in the list.

Select "Search for devices"

19

Select "End call".

c alling a contact

Press on Telephone to display the

primary page.

Or

"c onnect / disconnect" to start or

end the Bluetooth connection with

the selected device.

20

Or make a long press

Or

on the steering mounted TEL button.

"delete" to delete the pairing.

22

339

Audio and Telematics

Managing contacts / entries

Select "c ontacts".

Press on Telephone to display the

Select "directory information"

primary page.

for the number of entries used,

available, ...

3

18

Select the desired contact from the list offered.

Select "c ontacts".

3

Select "c all".

Select "Add contact".

9

c alling a recently used number

Select "c reate" to add a new contact.

14

Press on Telephone to display the

primary page.

Or

"Modify" to edit the selected contact.

Select "c all log".

15

2

Or

Select the desired contact from the list offered.

"delete" to delete the selected

contact.

16

It is always possible to make a call

directly from the telephone; park the

vehicle first as a safety measure.

Or

"delete all" to delete all information

for the selected contact.

17

Frequently asked questions

The following table groups together the answers to the most frequently asked questions concerning your audio system.

navigation

QUESTIOn

AnSWER

SOLUTIOn

The route calculation is

not successful.

The route settings may conflict with the current location (exclusion

of toll roads on a toll motorway).

Check the route settings in the "Navigation"

menu.

The POIs do not appear.

The POIs have not been selected.

Select the POIs in the list of POIs.

The Hazard zone audible

warning does not work.

The audible warning is not active.

Activate audible warnings in the "Navigation"

menu.

The system does not

The guidance criteria do not take account of TMC messages.

Select the "Traffic info" function in the list of route

suggest a detour around

an incident on the route.

settings.

I receive a Accident-prone Other than guidance, the system announces all Hazard zones

Zoom in on the map to view the exact position of the

Accident-prone area. Select "On the route" to no

longer receive alerts other than navigation instructions

or to reduce the time for the announcement.

area alert which is not on

positioned in a cone located in front of the vehicle. It may provide

an alert for a Hazard zone located on nearby or parallel roads.

my route.

341

Audio and Telematics

QUESTIOn

AnSWER

SOLUTIOn

Certain traffic jams along

the route are not indicated receive the traffic information.

in real time.

On starting, it is several minutes before the system begins to

Wait until the traffic information is being received

correctly (display of the traffic information icons

on the map).

The filters are too restrictive.

Modify the "Geographic filter" settings.

In certain countries, only major routes (motorways...) are listed for

the traffic information.

This phenomenon is normal. The system is

dependent on the traffic information available.

The altitude is not

displayed.

On starting, the initialisation of the GPS may take up to 3 minutes to Wait until the system has started up completely

receive more than 4 satellites correctly.

so that there is GPS coverage by at least

4 satellites.

Depending on the geographical environment (tunnel...) or the

weather, the conditions of reception of the GPS signal may vary.

This phenomenon is normal. The system

is dependent on the GPS signal reception

conditions.

Radio

QUESTIOn

AnSWER

SOLUTIOn

The quality of reception of The vehicle is too far from the transmitter used by the station

Activate the "RDS" function by means of the

short-cut menu to enable the system to check

whether there is a more powerful transmitter in

the geographical area.

the radio station listened

to gradually deteriorates

or the stored stations do

not function (no sound,

87.5 Mhz is displayed...).

listened to or there is no transmitter in the geographical area

through which the vehicle is travelling.

The environment (hills, buildings, tunnels, basement car parks...)

block reception, including in RDS mode.

This phenomenon is normal and does not

indicate a fault with the audio system.

The aerial is absent or has been damaged (for example when going Have the aerial checked by a CITROËN dealer.

through a car wash or into an underground car park).

I cannot find some radio

stations in the list of

stations received.

The station is not received or its name has changed in the list.

Some radio stations send other information in place of their name

(the title of the song for example).

The system interprets this information as the name of the station.

The name of the radio

station changes.

343

Audio and Telematics

Media

QUESTIOn

AnSWER

SOLUTIOn

Playback of my USB

memory stick starts only

after a very long wait

(around 2 to 3 minutes).

Some files supplied with the memory stick may greatly slow down

access to reading the memory stick (multiplication by 10 of the

catalogue time).

Delete the files supplied with the memory stick

and limit the number of sub-folders in the file

structure on the memory stick.

When I connect my iPhone When the iPhone connects automatically as a telephone, it forces

Disconnect and reconnect to the USB port

as a telephone and to

the USB port at the same

time, I am unable to play

the music files.

the streaming function. The streaming function takes the place

of the USB function which is then not useable, there is a period

without sound of the track being played with Apple^®players.

(the USB function takes priority over streaming).

The CD is ejected

automatically or is not

played by the player.

The CD is inserted upside down, is unplayable, does not contain any audio

data or contains an audio format which the player cannot play.

-

Check that the CD is inserted in the player the

right way up.

Check the condition of the CD: the CD cannot

be played if it is too damaged.

Check the content in the case of a recorded

CD: refer to the advice in the "AUDIO" section.

The audio system's CD player does not play

DVDs.

Some recorded CDs will not be played by

the audio system because they are not of the

correct quality.

The CD has been recorded in a format that is not compatible with the player (udf, ...).

The CD is protected by an anti-pirating protection system which is

not recognised by the audio system.

There is a long waiting

When a new medium is inserted, the system reads a certain

This phenomenon is normal.

period following the insertion amount of data (directory, title, artist, etc.). This may take from a few

of a CD or connection of a

USB memory stick.

seconds to a few minutes.

QUESTIOn

AnSWER

SOLUTIOn

The CD player sound is

poor.

The CD used is scratched or of poor quality.

Insert good quality CDs and store them in

suitable conditions.

The audio equipment settings (bass, treble, ambiences) are

unsuitable.

Set the treble or bass level to 0, without selecting

an ambience.

Some characters in the

media information are not

displayed correctly while

playing.

The audio system does not display some types of characters.

Use standard characters to name tracks and

folders.

Playing of streaming files

does not start.

The peripheral device connected does not support automatic play.

The Bluetooth profile does not allow the transfer of this information.

Start the playback from the device.

The names of tracks and

the track length are not

displayed on the screen

when streaming audio.

345

Audio and Telematics

Settings

QUESTIOn

AnSWER

SOLUTIOn

In changing the setting

of treble and bass the

equalizer setting is

deselected.

The selection of an equalizer setting imposes the balance settings.

Modifying one without the other is not possible.

Modify the balance or equalizer settings to obtain

the desired musical ambience.

In changing the equalizer

setting, treble and bass

return to zero.

When changing the

balance settings, the

distribution setting is

deselected.

The selection of a distribution setting imposes the balance settings. Modify the balance or distribution settings to

Modifying one without the other is not possible. obtain the desired musical ambience.

When changing an

distribution setting,

the balance setting is

deselected.

QUESTIOn

AnSWER

SOLUTIOn

There is a difference in

sound quality between the Treble, Equalizer and Loudness can be adapted to the different

different audio sources.

For optimum sound quality, the audio settings for Volume, Bass,

Check that the audio settings for (Volume, Bass,

Treble, Equalizer, Loudness) are adapted to the

sources listened to. It is advisable to set the

Audio functions (Bass, Treble, Fr-Re balance,

Le-Ri balance) to the middle position, select the

"Linear", musical ambience and set the loudness

correction to the "Active" position in CD mode or

to the "Inactive" position in radio mode.

sound sources, which may result in audible differences when

changing source.

With the engine off, the

When the engine is switched off, the system's operating time

Start the vehicle's engine to increase the battery

charge.

system switches off after a depends on the state of charge of the battery.

few minutes of use. The switch-off is normal: the system switches to economy mode

and switches off to prevent discharging of the vehicle's battery.

347

Audio and Telematics

Telephone

QUESTIOn

AnSWER

SOLUTIOn

I cannot connect my

Bluetooth telephone.

The telephone's Bluetooth function may be switched off or the

telephone may not be visible.

-

Check that your telephone's Bluetooth

function is switched on.

Check in the telephone settings that it is

"visible to all".

The Bluetooth telephone is not compatible with the system.

The volume depends both on the system and on the telephone.

You can check the compatibility of your

telephone at

The volume of the

telephone connected

in Bluetooth mode is

inaudible.

Increase the volume of the audio system, to

maximum if required, and increase the volume of

the telephone if necessary.

The ambient noise level has an influence on the quality of

telephone communication.

Reduce the ambient noise level (close the

windows, reduce the booster fan speed, slow

down, ...).

Some contacts are

duplicated in the list.

The options for synchronizing contacts are synchronizing the

contacts on the SIM card, the contacts on the telephone, or both.

When both synchronizations are selected, some contacts may be

duplicated.

Select "Display SIM card contacts" or "Display

telephone contacts".

Contacts are not shown in Some telephones offer display options. Depending on the settings

alphabetical order. chosen, contacts can be transferred in a specific order.

Modify the display setting in the telephone

directory.

The system does not receive The Bluetooth mode does not permit sending SMS text messages

SMS text messages. to the system.

349

Audio and Telematics

Audio system / Bluetooth^®

Contents

350

First steps

Steering mounted controls

Menus

351

352

Audio

353

Using the telephone

Audio settings

Screen menu map(s)

360

368

369

Frequently asked questions

371

As a safety measure, the driver must only carry out operations

The system is coded in such a way that it will only operate in

your vehicle.

which require prolonged attention while the vehicle is stationary.

When the engine is switched off and to prevent discharging of

the battery, the audio system may switch off after a few minutes.

First steps

Confirmation or display of contextual

menu.

Manual step by step search up /

down for radio frequencies.

Select previous / next MP3 folder.

Select previous / next folder / genre /

artist / playlist in the USB device.

Navigation in a list.

Automatic search up / down for radio

frequencies.

Select previous / next CD, USB,

streaming track.

On / Off.

Display the list of stations received,

CD/MP3 tracks or folders.

Long press: managing the

classification of MP3/WMA files /

update the list of stations received.

Navigation in a list.

Abandon the current operation.

Up one level (menu or folder).

Volume adjustment.

TA (Traffic Announcement) function

On / Off.

Long press: access to type of

information.

Select screen display between modes:

Full screen: Audio (or telephone if call

in progress) /

In a window: Audio (or telephone

if call in progress) - Time or Trip

computer.

Audio settings:

audio ambiences, treble, bass,

loudness, distribution, left/right

balance, front/rear fader, automatic

volume.

Access to main menu.

Long press: black screen (DARK).

Select preset radio station.

Long press: store a station.

Select source:

Selection of AM / FM wavebands.

Radio, CD, AUX, USB, Streaming.

Accept an incoming call.

351

Audio and Telematics

Steering mounted controls

Media: change the multimedia

source.

Telephone: call.

Call in progress: access to the

telephone menu (end call, secret

mode, hands-free mode).

Telephone, press and hold: reject an

incoming call, end a call; when there

is no call in progress, access to the

telephone menu.

Radio: display the list of stations.

Media: display the list of tracks.

Radio, press and hold: update the list

of stations received.

Increase volume.

Decrease volume.

Radio, rotate: automatic search for

the previous / next station.

Media, rotate: previous / next track.

Press: confirm a selection.

Menus

Screen c

"Multimedia": Media parameters,

Radio parameters.

For a detailed global view of the menus

available, refer to the "Screen menu

map" section.

"Telephone": Call, Directory

management, Telephone

management, Hang up.

"Bluetooth connection":

Connections management, Search

for a device.

"Personalisation-configuration":

Define the vehicle parameters,

Choice of language, Display

configuration, Choice of units, Date

and time adjustment.

353

Audio and Telematics

Audio

Radio

A long press on LIST builds or

updates the list of stations; audio

reception is cut momentarily.

Selecting a station

The exterior environment (hills, buildings,

tunnel, car park, below ground...) may

prevent reception, even in RDS station

tracking mode. This phenomenon is

normal in the propagation of radio waves

and is in no way indicative of a fault with

the audio system.

Press SOURc E or SRc several

times in succession and select radio.

Press BAnd to select a waveband.

Press LIST to display the list of

stations received in alphabetical

order.

Select the desired radio station and

confirm by pressing OK.

A press changes to the next or

previous letter (e.g. A, B, D, F, G,

J, K, ...).

RdS

Receiving TA messages

Receiving InFO messages

RDS, if displayed, enables you to continue

The TA (Traffic Announcement)

function gives priority to TA alert

The INFO function gives priority to

TA alert messages. To be active, this

function needs good reception of a

radio station that transmits this type

of message. When a message is

transmitted, the current audio source

(Radio, CD, USB, ...) is interrupted

automatically to receive the INFO

message. Normal play resumes at the

end of the message transmission.

listening to the same station by automatic

retuning to alternative frequencies.

However, in certain conditions, coverage

of an RDS station may not be assured

throughout the country as radio stations

do not cover 100 % of the territory. This

explains the loss of reception of the station

during a journey.

messages. To operate, this function

needs good reception of a radio station

transmitting this type of message.

When a traffic report is transmitted,

the current audio source (Radio, CD,

USB, ...) is interrupted automatically to

play the TA message. Normal playback

of the audio source resumes at the end

of the transmission of the message.

When the radio is displayed on the

screen, press OK to display the

contextual menu.

Press TA In FO to activate or

deactivate the reception of traffic

messages.

Make a long press on TA In FO to

display the list of categories.

Select "RdS" and confirm to save.

"RdS" is displayed in the screen.

Select or deselect categories to

activate or deactivate the reception of

the corresponding messages.

355

Audio and Telematics

display RAdIO TEXT

Audio cd

Playing a cd

Radio text is information transmitted by

the radio station related to the current

programme or song.

Insert 12 cm diameter circular compact

discs only.

Some anti-pirating systems, on original

discs or CDs copied using a personal

recorder, may cause faults which are no

reflection on the quality of the original

player.

Screen c

With the radio displayed on the

screen, press OK to display the

contextual menu.

Without pressing the EJEc T button,

insert a CD in the player, play begins

automatically.

Select "RadioText (TXT) display"

and confirm OK to save.

To play a disc which has already

been inserted, press the SOURc E

or SRc button several times in

succession and select "cd ".

Press LIST to display the list of

tracks on the CD.

Press one of the buttons to select a

track on the CD.

Press and hold one of the buttons for

fast forward or backward.

cd , USB

Information and advice

The audio system will only play files with

extension ".mp3" or ".wma" and a compression

rate that is constant or variable between

32 Kbps and 320 Kbps.

In order to be able to play a recorded CDR or

CDRW, when recording it is preferable to select

standards ISO 9660 level 1.2 or Joliet.

If the disc is recorded in another format, it may

not be played correctly.

It is recommended that the same recording

standard is always used for an individual disc,

with as low a speed as possible (4x maximum)

for optimum sound quality.

In the particular case of a multi-session CD,

the Joliet standard is recommended.

It is advisable to restrict file names to

20 characters without using special characters

(e.g. " ? ; ù) to avoid any playing or displaying

problems.

The playlists accepted are types .m3u and .pls.

The number of files is limited to 5 000 in

500 directories on a maximum of 8 levels.

Use only USB memory sticks formatted FAT32

(File Allocation Table).

On a single disc, the CD player can

read up to 255 MP3 files spread

over 8 directory levels. However, it

is recommended that this be kept to

2 levels so as to limit the time taken to

access and play the CD.

Do not connect a hard disk or USB

device other than audio players to the

USB port. This may cause damage to

your installation.

During play, the folder structure is not

observed.

357

Audio and Telematics

cd , USB

To play a disc or memory stick which

has already been inserted, press

SOURc E or SRc several times in

succession and select "cd " or "USB".

Select a track or a folder.

Playing a compilation

Insert an MP3 compilation in the CD

player or connect a memory stick to the

USB port, directly or via an extension

lead.

Press one of the buttons to select the

next or previous track.

Up a level in the menu.

Skip a track.

The system creates playlists (temporary

memory) the creation time for which can take

from a few seconds to several minutes.

The playlists are updated every time the

ignition is switched off or a USB memory stick

is connected.

Play starts automatically after a period which

depends on the capacity of the USB memory

stick.

Press one of the buttons to select the

next or previous folder in the order

chosen.

Press and hold one of the buttons for

fast forwards or backwards.

Press LIST to display the menu of

folders in the compilation.

At a first connection, the order suggested is

by folder. When connecting again, the order

previously chosen is retained.

Select a line in the list.

USB memory stick - File

sorting

USB players

Make a long press on LIST or press

MEnU, select "Multimedia", then

"Media parameters" and finally

"c hoice of track listing" to display

the different types of sorting.

If the portable player is not recognised by the

USB port, connect it to the auxiliary Jack socket.

The Apple^®player must be updated regularly

for the best connection.

The playlists are those defined in the Apple^®

player.

Having selected the desired sorting

("By folders", "By artists", "By

genres", "By playlists") press OK.

Then confirm OK to save the

modifications.

The audio files on a Mass Storage portable

player* can be heard through the vehicle's

speakers by connecting it to the USB port

(cable not supplied).

The Apple^®player must be generation 5 or

later.

-

By folders: all folders containing

audio files recognised on the

peripheral device, in alphabetical

order without following the folder

structure.

Management of the device is via the

audio system controls.

-

By artists: all of the artist names

defined in the ID3 Tags, in

alphabetical order.

-

By genres: all of the genres

defined in the ID3 Tags.

By playlists: if playlists have

been saved.

* Check your player's manual.

359

Audio and Telematics

Auxiliary socket (AUX)

Streaming - Playing audio

files via Bluetooth

Press the SOURc E or SRc button

several times in succession and

select "AUX".

depending on the compatibility of the phone

Streaming allows music files on a telephone to

be heard via the vehicle's speakers.

The telephone must support the appropriate

Bluetooth profiles (Profiles A2DP / AVRCP).

First adjust the volume on your portable device.

Then adjust the volume of the audio

system.

Pair/connect the telephone: see the

"USING THE TELEPHONE" section.

The auxiliary Jack socket permits the

connection of a portable non-mass storage

device or an Apple^®player if not recognised by

the USB port.

The display and management of controls is on

the portable device.

Activate the streaming source by

pressing SOURc E or SRc. Control

of playback is via the audio system.

The contextual information can be

displayed in the screen.

Do not connect a device to the USB

port and to the auxiliary Jack socket at

the same time.

Connect the portable device to the auxiliary

Jack socket using a suitable cable (not

supplied).

In certain cases, playing of the

audio files must be initiated from the

telephone.

The audio quality depends on the quality of the

transmission from the telephone.

Using the telephone

Pairing a telephone

First connection

Play mode

Select "Multimedia" and confirm.

The services offered depend on the network,

the SIM card and the compatibility of the

Bluetooth telephone used.

Consult your telephone's manual and your

operator to find out which services are

available to you.

The play modes available are:

-

Normal: the tracks are played

in order, depending on the

classification of the selected files.

Random: the tracks in an album

or folder are played in a random

order.

Random all: all of the tracks saved

in the media are played in random

order.

Select "Media parameters" and

confirm.

As a safety measure and because they

require prolonged attention on the part

of the driver, the operations for pairing

of the Bluetooth mobile telephone with

the Bluetooth hands-free system of

your audio system must be carried out

with the vehicle stationary and the

ignition on.

Repeat: the tracks played are only

those from the current album or

folder.

Select "Read mode" and confirm.

Visit

information (compatibility, additional

help, ...).

Press OK for access to the

contextual menu.

or

Press MEnU.

Activate the telephone's Bluetooth function

and ensure that it is "visible to all" (refer to the

telephone user guide).

Select the desired play mode and

confirm OK to save the modifications.

Press MEnU.

361

Audio and Telematics

Streaming - Playing audio

files via Bluetooth

Select "Bluetooth connection" and

confirm.

A virtual keypad is displayed on the

screen: enter a code with at least

4 digits and conform with OK.

Pair/connect the telephone then listen: see the

AUDIO section.

A message is displayed on the screen of the

telephone: enter the same code and confirm.

Select "Search for a device".

If pairing fails, try again; the number of attempts is not limited.

Accept the connection to the telephone.

A message appears in the screen to confirm

the result of the connection.

A window is displayed "Search in progress…".

Pairing can also be initiated from the

telephone by searching for detected

Bluetooth devices.

Select the telephone to be connected

from the list. Only one telephone can

be connected at a time.

The directory and the calls list can be

accessed after the synchronisation

period (if the telephone is compatible).

Automatic connection must be

configured in the telephone to allow

the connection each time the vehicle is

started.

In some cases, the reference number of the

telephone or the Bluetooth address may appear

instead of the name of the telephone.

Managing connections

Indicates that a device is connected.

Then select and confirm:

The telephone connection automatically

includes hands free operation and

audio streaming.

The ability of the system to connect

to just one profile depends on the

telephone. Both profiles may connect

by default.

-

"c onnect telephone" /

"disconnect telephone":

to connect / disconnect the

telephone or the hands-free

connection only.

Indicates connection of the audio

steaming profile.

-

"c onnect media player" /

"disconnect media player":

to connect / disconnect only

streaming.

"c onnect telephone +

media player" / "disconnect

telephone + media player":

to connect / disconnect the

telephone (hands-free and

streaming).

Press MEnU.

Indicates connection of the hands-

free profile.

Select "Bluetooth connection" and

confirm.

Select a telephone and confirm.

-

"delete connection": to delete

the pairing.

Select "c onnections management"

and confirm. The list of paired

telephones is displayed.

363

Audio and Telematics

Making a call - dialling

To display the "TELEPHOnE" menu:

Select numbers one at a time using

-

Make along press on SOURc E

or SRc.

the 7 and 8 buttons and confirm.

-

Or, press OK to display the

contextual menu. Select "c all"

and confirm.

-

Or, press MEnU, select

"Telephone" and confirm. Select

"c all" and confirm.

Correction allows numbers to be deleted one

at a time.

Select "dial" to enter a number and

Select OK and confirm to start the

confirm.

call.

Making a call - Recently

called numbers*

Making a call - From the

directory of contacts

To display the "TELEPHOnE" menu:

Select the number and confirm to

start the call.

To display the "TELEPHOnE" menu:

-

Make a long press on SRc /TEL.

Or, press the dial to display the

contextual menu. Select "c all"

and confirm.

-

Make a long press on SRc /TEL.

Or, press the dial to display the

contextual menu. Select "c all"

and confirm.

-

Or, press MEnU, select

-

Or, press MEnU, select

"Telephone" and confirm.

Select "c all" and confirm.

"Telephone" and confirm. Select

"c all" and confirm.

The calls list includes calls sent and

received in the vehicle using the

connected telephone.

Select "c alls list" and confirm.

Select "directory" and confirm.

It is possible to make a call directly

from the telephone; park the vehicle

first as a safety measure.

* Depending on the compatibility of the telephone.

365

Audio and Telematics

Receiving a call

Managing calls

Select a contact then confirm.

Home

An incoming call is announced by a ring and

a superimposed display in the multifunction

screen.

During a call, press OK to display the

contextual menu.

Business

Mobile

"YES" to accept the call is selected

by default.

Hang up

(depending on the information

Press OK to accept the call.

Select "nO" and confirm to reject

the call.

or

In the contextual menu, select "Hang

up" to end the call.

available in the contact

records of the telephone

connected).

Press one of these buttons to accept

the call.

Select the number and confirm.

A long press on ESc or on TEL,

SOURc E or SRc also rejects an

incoming call.

A long press on one of these buttons

also ends the call.

Secret - Mute

c ombined mode

Interactive voice response

(to leave the vehicle without ending the call)

(so that the caller cannot hear)

From the contextual menu, select

"dTMF tones" and confirm to use

the digital keypad to navigate in the

interactive voice response menu.

In the contextual menu:

-

select "Telephone mode" to

transfer the call to the telephone.

deselect "Telephone mode" to

transfer the call to the vehicle.

-

In the contextual menu:

-

select "Micro OFF" to switch off

the microphone.

-

deselect "Micro OFF" to switch

the microphone on.

In certain cases, the combined mode has to

activated from the telephone.

c onsultation call

If the contact has been cut off, when you

reconnect on returning to the vehicle,

the Bluetooth connection will be restored

automatically (depending on the compatibility of

the telephone).

From the contextual menu, select

"Switch" and conform to return to a

call left on hold.

367

Audio and Telematics

AUDIO and TELEMATICS for Your DS 5 4 Door First Generation (2011-2018)

Related Topics

Popular Owner Manuals

Latest Owner Manuals