Get Multimedia Guide for Fiat 500 C 2 Door Second Generation (2021-2025)

MULTIMEDIA

TIPS, CONTROLS AND GENERAL

INFORMATION................................174

This chapter describes the main

functions of the Uconnect™ Radio,

Uconnect™ 5" LIVE, Uconnect™ 5"

Nav LIVE, Uconnect™ 7” HD LIVE and

Uconnect™ 7” HD NAV LIVE

infotainment systems that can be fitted

on the vehicle.

USB SOURCE.................................175

UCONNECT™ RADIO.....................176

UCONNECT™ 5 RADIO LIVE/ NAV

LIVE ................................................183

UCONNECT™ 7 HD LIVE/ NAV

LIVE ................................................196

MOPAR® CONNECT......................211

OFFICIAL TYPE APPROVALS .........212

173

Anti-theft protection

After the 3 available attempts to enter

the code, the system displays

TIPS, CONTROLS

AND GENERAL

INFORMATION

The system is equipped with an

anti-theft protection system based on

the exchange of information with the

electronic control unit (Body Computer)

on the vehicle.

This guarantees maximum safety and

prevents the secret code from being

entered after the power supply has

been disconnected.

If the check has a positive outcome, the

system will start to operate, whereas if

the comparison codes are not the

same or if the electronic control unit

(Body Computer) is replaced, the

system will ask the user to enter the

secret code according to the procedure

described in the paragraph below.

“Incorrect Code. Radio locked. Wait for

30 minutes”. After the text has

disappeared it is possible to start the

code entering procedure again.

Vehicle radio passport

This document certifies ownership of

the system. The vehicle radio passport

shows the system model, serial number

and secret code.

WARNING Keep the vehicle radio

passport in a safe place so that you

can give the information to the relevant

authorities if the system is stolen.

In case of loss of the car radio

passport, contact the Fiat Dealership,

taking an ID document and the car

ownership documents.

Road safety

Learn how to use the various system

functions before setting off.

Read the instructions for the system

carefully before setting off.

Reception conditions

Reception conditions change

constantly while driving. Reception may

be interfered with by the presence of

mountains, buildings or bridges,

especially when you are far away from

the broadcaster.

IMPORTANT The volume may be

increased when receiving traffic

bulletins.

Entering the secret code

Important notes

Care and maintenance

When the system is switched on, if the

code is requested, the display will

show “Please enter Anti-Theft Code”

followed by the screen showing a

keypad to enter the secret code.

The secret code is made up of four

digits from 0 to 9.

If an incorrect code is entered, the

system displays “Incorrect Code” to

notify the user of the need to enter the

correct code.

In the event of an anomaly, the system

should only be checked and repaired at

a Fiat Dealership.

If the temperature is particularly low, the

display may take a while to reach

optimum brightness.

If the car is stopped for a while and the

external temperature is very high, the

system may go into “thermal

protection” mode, suspending

operation until the temperature in the

passenger compartment returns to

acceptable levels.

Observe the following precautions to

ensure the system is fully operational:

the display is sensitive to scratching,

liquids and detergents. Avoid hitting

the display with pointed or hard objects

that could damage its surface. Do not

press on the display when cleaning it.

never use alcohol, petrols and

derivatives to clean the display lens.

Prevent any liquid from entering the

system: this could damage it beyond

repair.

174

Look at the screen only and when it is

necessary and safe. If you need to look

at the screen for a long time, pull over

to a safe place so as not to be

USB SOURCE

To activate the USB mode, insert the

corresponding device into the USB port

on the central tunnel in the car.

IMPORTANT NOTE After using a USB

recharging socket, disconnect the

device (smartphone), always removing

the cable from the vehicle socket first,

never from the device. Cables left flying

or connected incorrectly could

distracted while driving.

Immediately stop using the system in

the event of a fault. Otherwise the

system might be damaged. Contact a

Fiat Dealership as soon as possible

to have the system repaired.

compromise correct recharging and/or

the USB socket condition.

NOTE The USB port handles data

transmission from the Pen Drive/

Smartphone, etc. and slow recharging

of an external device, which is not

guaranteed as it depends on the device

type/brand.

175

UCONNECT™ RADIO

.

CONTROLS ON FRONT PANEL

F0S0619

141

176

FRONT CONTROL PANEL SUMMARY TABLE

Button

Functions

Mode

Ignition

Short button press

Switching off

Volume adjustment

Turning the knob clockwise/anticlockwise

Volume activation/deactivation (Mute/Pause)

Short button press

Exit the selection/return to previous screen

Short button press

Scrolling the list or tuning to a radio station or select

previous/next track

Turning the knob clockwise/anticlockwise

BROWSE

ENTER

Confirmation of the option displayed

Display mode selection (Radio, Media Player)

Access to the sound setting and adjustment functions

Access to the Settings menu

Short button press

Long button press

Short button press

INFO

AUDIO

MENU

MEDIA

RADIO

USB source selection

Access to the Radio mode

Store current radio station

1-2-3-4-5-6

A-B-C

Stored radio station recall

Selection of the group of radio presets or selection of the

desired letter in each list

Short button press

Long button press

Search for previous radio station or selection of USB

previous track

Scan of lower frequencies until released/Fast rewind of USB

track

177

Button

Functions

Mode

Search for next radio station or selection of USB next track

Short button press

Long button press

Scan of higher frequencies until released/Fast forward of

USB track

Shuffle of USB tracks

USB loop

Short button press

178

CONTROLS ON THE STEERING WHEEL

(where provided)

The controls for the main system functions are present on the steering wheel to make control easier.

The activation of the function selected is controlled, in some cases, by how long the button is pressed (short or long press) as

described in the table below.

F0S0620

142

179

Button

Interaction (pressure/rotation)

Deactivate/reactivate the microphone during a phone conversation

Activation/deactivation of the USB source Pause

Activation/deactivation of the radio source Mute function

Short press: volume increase/decrease in single steps

+/–

Long press: volume continuous increase/decrease until released

Short press (Radio mode): selection of next/previous station

Long press (Radio mode): scan higher/lower frequencies until released

Short press (USB mode): selection of previous/next track

Long press (USB mode): fast forward/rewind until released

SRC

select available audio sources: Radio or USB

180

SWITCHING THE SYSTEM

ON/OFF

FM station list

Previous/next radio station fast

search

Press the BROWSE ENTER button/

knob to display the complete list of the

FM stations that can be received.

The system is switched on/off by

pressing the button/knob.

Turn the button/knob clockwise to

increase the radio volume or

anticlockwise to decrease it.

Hold down the

or

button to

start the fast search: when the button is

released, the first tunable radio is

played.

AM/FM radio station storage

The preset stations are available in all

system modes and are selected by

touching one of the presetting buttons

1-2-3-4-5-6 on the front panel.

If you are tuned to a radio station that

you wish to store, hold down the button

on the display which corresponds to

the desired preset until an acoustic

confirmation signal is emitted.

MEDIA MODE

RADIO (TUNER) MODE

This paragraph describes the ways of

interacting with USB operation.

The system is equipped with the

following tuners: AM, FM.

Audio source selection

Radio mode selection

Press the MEDIA button to select the

USB audio source.

Press the RADIO button on the front

panel to activate radio mode.

Change track (next/previous)

Selecting a frequency band

Briefly press the

BROWSE ENTER button/knob

clockwise to play the next song. Briefly

button or turn the

AM/FM radio station selection

The different tuning modes can be

selected by pressing the RADIO button

on the front panel.

To search for the desired radio station,

press the

or

buttons, use

press the

button or turn the

the wheel on the steering wheel

BROWSE ENTER button/knob

anticlockwise to return to the beginning

of the song, or return to the beginning

of the previous song if the current song

has been playing for less than 3

seconds.

Displayed information

controls

or, alternatively, turn the

"BROWSE/ENTER" knob.

After the desired radio station is

selected on the display, the following

information is shown (INFO mode

activated):

In the upper part: the preset station,

the time and the other active radio

settings are highlighted (e.g.: TA).

In the central part: the name of the

current station, the frequency and

the radio text information (if any) are

highlighted.

Previous/next radio station search

Briefly press the

or use the wheel on the steering wheel

controls : when the button is

or

button

Fast forward/rewind through tracks

released, the previous or next radio

station is displayed.

Press and hold down the

to fast forward the selected track or

keep the button pressed to fast

rewind the track.

button

181

Track selection (browse)

Shuffle

Radio Off Delay: lets you keep the

system on for a preset time after

turning the ignition key to the STOP

position.

Use this function to scroll through and

select the tracks on the active device.

The choices available depend on the

device connected.

Press the

on USB in a random order.

Press again to deactivate the function.

button to play the tracks

Audio mode

Repeat

For example, on a USB device, you can

also use the BROWSE ENTER

button/knob to scroll through the list of

artists, genres and albums available

on the device, depending on the

information available in the tracks.

Within each alphabetical list, the A-B-C

button on the front panel allows the

user to skip to the desired letter in the

list.

Press the BROWSE ENTER button to

activate this function on the source

being played.

Turn the BROWSE ENTER button/knob

to select the desired category and

then press the button/knob to confirm

the selection.

To access the "Audio" settings menu

briefly press the AUDIO button on

the front panel.

Press the

function. The corresponding icon is

displayed.

button to activate this

The menu includes the following items:

Press again to deactivate the function.

NOTE The Uconnect™ system may

not support some USB keys: in this

case, it will not automatically switch

from “Radio” mode to “Media” mode. If

the device used does not play, verify

its compatibility by selecting Media

mode: a dedicated message will

appear on the Uconnect™ system

display.

TREBLE: adjustment of high tones;

MID: adjustment of mid tones;

BASS: adjustment of bass tones;

BALANCE: balancing of left/right

speakers;

SVC: speed adjustment according

to vehicle speed;

LOUDNESS: audio improvement at

low volume;

SETTINGS

Press the MENU button on the front

panel to display the "Settings" menu.

NOTE The menu items displayed can

vary according to the versions.

Press the

function.

button to cancel the

Track information display

The menu includes the following items:

System Settings: Language,

Restore Default Values, System Power

Off, Volume Limited at Power On,

Auto-On Radio.

Press the INFO button to select the

information displayed while playing

(Artist, Album, Genre, Name, Folder,

File name).

Press the

button to exit the screen.

Radio Menu: Browse FM Station

List, Traffic Announcement (TA),

Regional, Alternative Frequency (AF).

182

Uconnect™ 5 Radio LIVE/ NAV LIVE

.

Controls on front panel

F0S0621

143

183

Front control panel summary table

Button

Functions

Mode

Ignition

Short button press

Switching off

Volume adjustment

Left/right rotation of knob

Short button press

Volume activation/deactivation (Mute/Pause)

Display on/off

Short button press

Exit the selection/return to previous screen

Settings

Scrolling the list or tuning to a radio station

Confirmation of the option displayed

Left/right rotation of knob

Short button press

BROWSE ENTER

Access to the additional functions, e.g.: Time display, Compass

(where provided), External temperature, Radio Media and

Uconnect™ LIVE services, where present.

APPS

Short button press

PHONE

Phone data display

TRIP

(Uconnect™ 5" LIVE

versions)

Access to the Trip menu

NAV

(Uconnect™ 5" Nav

LIVE versions)

Access to the Navigation menu

Short button press

MEDIA

RADIO

Short button press

Source selection: USB, Bluetooth®

Access to the Radio mode

184

Controls on the steering wheel

The controls for the main system functions are present on the steering wheel to make control easier. The activation of the

function selected is controlled, in some cases, by how long the button is pressed (short or long press) as described in the table

below.

F0S0622

144

185

Controls on steering wheel summary table

Text

Interaction (pressure/rotation)

Acceptance of incoming call;

Acceptance of the second incoming phone call and putting the active phone call on hold;

Last 10 calls list on the instrument panel (with call browsing active and phone paired only)

Rejection of incoming call;

Ending of call in progress;

Exit the display on the instrument panel of the last calls (only with call browsing active)

Deactivation/reactivation of the microphone during a phone conversation;

Activation/deactivation of the USB, Bluetooth® source Pause;

Activation/deactivation of radio Mute function

Short press: volume increase/decrease in single steps;

+/-

Long press: volume continuous increase/decrease until released

Activation of voice recognition;

Interruption of the voice message in order to give a new voice command;

Interruption of voice recognition

Short press (Radio mode): selection of next/previous station

Long press (Radio mode): scan higher/lower frequencies until released

Short press (USB, Bluetooth® mode): selection of previous/next track

Long press (USB, Bluetooth® mode): fast forward/rewind until released

Short press (phone mode): selection of next/previous call (only with call browsing active)

186

Switching the system

on/off

Audio menu

NOTE The keyboard is not available for

languages not supported by the system

which feature special characters (e.g.

Greek). In these cases this function will

be limited.

NOTE The Uconnect™ system may

not support some USB keys: in this

case, it will not automatically switch

from “Radio” mode to “Media” mode. If

the device used does not play, verify

its compatibility by selecting Media

mode: a dedicated message will

appear on the Uconnect™ system

display.

The following adjustments can be

carried out using the “Audio” menu:

The system is switched on/off by

pressing the (ON/OFF) button/knob.

“Equaliser” (where provided);

Turn the button/knob clockwise to

increase the radio volume or

anticlockwise to decrease it.

“Balance” (left/right audio balance

adjustment);

“Speed/Volume” (speed-dependent

automatic volume control);

Radio mode

“Loudness” (where provided);

“Auto-On Radio”;

After the desired radio station is

selected, the following information is

shown on the display:

At the top: the list of radio stations

stored (preset) is displayed; the station

currently playing is highlighted.

In the middle: display of the name of

the current radio station and the

buttons for selecting the previous or

next radio station.

“Radio Off Delay”.

To exit the “Audio” menu, press the

Done button.

/

Bluetooth® source

Media mode

Pairing a Bluetooth® audio device

Audio source selection

To pair a Bluetooth® audio device,

proceed as follows:

activate the Bluetooth® function on

the device;

press the MEDIA button on the front

panel;

Press the "Source" button to select the

desired audio source among those

available: USB or Bluetooth®.

Applications used on portable devices

may be not compatible with the

Uconnect™ system.

At the bottom: display of the following

buttons:

“Browse”: list of the radio stations

available;

if the “Media” source is active, press

the “Source” button;

“AM/FM”, “AM/DAB”, “FM/DAB”:

selection of the desired frequency band

(button reconfigurable according to

the band selected: AM, FM or DAB);

Track selection (Browse)

With Media mode active, briefly press

select the Bluetooth® Media

source;

buttons

previous/next track or keep buttons

pressed to fast rewind/

forward the track.

/

to play the

press the “Add Device” button;

“Tune”: manual radio station tuning

(not available for DAB radio)

/

search for Uconnect™ on the Blu-

etooth® audio device (during the pair-

ing stage a screen is displayed showing

the progress of the operation);

“Info”: additional information on the

source being listened to;

“Audio”: access to the “Audio

Settings” screen.

187

when requested by the audio

device, enter the PIN code shown on

the system display or confirm on the

device the PIN displayed;

Phone mode

press the PHONE button on the

front panel;

Phone mode activation

if no phone is paired with the system

yet, the display shows a dedicated

screen;

Press the PHONE button on the front

panel to activate the Phone mode.

Use the buttons on the display to:

if the pairing procedure is completed

successfully, a screen is displayed.

Answer “Yes” to the question to pair the

Bluetooth® audio device as favourite

(the device will have priority over all

other devices to be paired subse-

quently). If “No” is selected, the priority

is determined according to the order of

connection. The last device connected

will have the highest priority;

an audio device can also be paired

by pressing the PHONE button on

the front panel and by selecting

“Settings” or, from the “Settings” menu,

selecting “Phone/Bluetooth”.

IMPORTANT If the Bluetooth® con-

nection between mobile phone and

system is lost, consult the mobile

phone handbook.

NOTE When modifying the name-

device in the Bluetooth® settings of

the phone (where provided), the Radio

may change the track being played if

the device is connected via USB after

the Bluetooth® connection.

select “Yes” to start the pairing

procedure, then search for the

Uconnect™ device on the mobile

phone (if "No" is selected, the Phone

main screen is displayed);

dial the phone number (using the

graphic keypad on the display);

display and call the contacts in the

mobile phone phonebook;

display and call contacts from the

registers of previous calls;

when prompted by the mobile

phone, use its keypad to enter the PIN

code shown on the system display

or confirm on the mobile phone the PIN

displayed;

pair up to 10 phones/audio device

to make access and connection easier

and quicker;

transfer calls from the system to the

mobile phone and vice versa and

deactivate the microphone audio for

private conversations.

The mobile phone audio is transmitted

through the vehicle’s audio system;

the system automatically mutes the

radio when the Phone function is used.

NOTE To consult the list of mobile

phones and supported functions, visit

the www.driveuconnect.eu website

from the “Phone” screen you can

always pair a mobile phone by pressing

the “Settings” button: press the “Add

Device” button and proceed as

described above;

during the pairing stage a screen is

displayed showing the progress of

the operation;

when the pairing procedure is

completed successfully, a screen is

displayed: answer “Yes” to the question

to pair the mobile phone as favourite

(the mobile phone will have priority over

all other mobile phones to be paired

subsequently). If no other devices are

paired, the system will consider the first

associated device as favourite.

Pairing a mobile phone

To pair the mobile phone, proceed as

follows:

activate the Bluetooth® function on

the mobile phone;

188

NOTE After updating the phone

software, for proper operation, it is

recommended to remove the phone

from the list of devices linked to the

radio, delete the previous system

pairing also from the list of Bluetooth®

devices on the phone and make a new

pairing.

When a text message is received, the

display will show a screen where the

options “Listen”, “Call” or “Ignore” can

be selected.

You can access the SMS message list

received by the cell by pressing the

I will be late.

Stuck in traffic.

Start without me.

Where are you?

Are you there yet?

I need directions.

I'm lost.

graphic

button (the list shows

a maximum of 60 received messages).

NOTE On some mobile phones, to

make the SMS voice reading function

available, the SMS notification option

on the phone must be enabled; this

option is usually available on the phone,

in the Bluetooth® connections menu

for a device registered as Uconnect™.

After enabling this function on the

Making a phone call

See you later.

I will be 5 (or 10, 15, 20, 25, 30, 45,

60)* minutes late.

The operations described below can

only be accessed if supported by

the mobile phone in use.

For all functions available, refer to the

mobile phone owner's handbook.

A call can be made by:

See you in 5 (or 10, 15, 20, 25, 30,

45, 60)* minutes.

* Only use the numbers listed,

otherwise the system will not take the

message.

NOTE See the dedicated section for

details on how to send a text message

using the voice commands.

selecting the

icon (mobile

mobile phone, it must be disconnected

and reconnected with the Uconnect™

system in order to make it effective.

phone phonebook);

selecting “Recent Calls”;

selecting the icon;

SMS message options

APPS Mode

pressing the “Redial” button.

Default text messages are stored in the

system memory and can be sent to

answer a received message or as

a new message:

Press the APPS button on the front

panel to display the following operating

settings:

Text message reader

The system can read the messages

received by the mobile phone.

To use this function the mobile phone

must support the SMS exchange

function through Bluetooth®.

Where operation is not supported by

the phone, the relative graphic

Yes.

External temperature

Clock

No.

Okay.

Compass (NAV versions only)

I can't talk right now.

Call me.

Trip (for versions/markets, where

provided)

button is deactivated (goes grey).

Uconnect™ LIVE

I'll call you later.

I'm on my way.

Thanks.

189

Uconnect™ LIVE

Services

First access to the car

Settings of the Uconnect™ services

that can be managed through the

radio

Once you have launched the

Press the APPS button to access a

radio menu which shows all the

application functions of the system,

such as: Trip computer (where

Uconnect™LIVE App and entered

your details, you have to pair the Blu-

etooth® with your smartphone and the

radio, as described in the "Pairing a

mobile phone" paragraph, to access

the Uconnect™ LIVE services in your

car.

The list of supported mobile phones is

available on www.driveuconnect.eu.

When pairing is complete, the

connected services can be accessed

by pressing the Uconnect™ LIVE icon

on the radio.

When the activation process is

complete, a message will inform the

user. If a personal profile is necessary

for the services, your accounts can

be connected through the Uconnect™

LIVE App, or in your personal area on

www.driveuconnect.eu.

You can access the the "Settings"

section from the Uconnect™ LIVE

radio menu by pressing the

icon. In

this section the user can check the

system options and change them

according to their preferences.

provided), Settings, Compass (for

versions/markets, where provided),

Uconnect™ LIVE applications.

If there is a Uconnect™ LIVE icon, the

system is set up for the connected

services and allows the applications to

be used directly from the radio, for a

more efficient and advanced use of the

vehicle. The application functions are

present according to the vehicle

configuration and to the market.

To use the Uconnect™LIVE services,

you must:

Systems updating

If an update is available for the

Uconnect™ LIVE system while you

are using the Uconnect™ services,

you will be informed with a message on

the radio screen.

The update requires downloading the

new version of the Uconnect™ LIVE

services management software. It is

done using the data connection of the

paired smartphone. The amount of

traffic generated will be communicated

to the user.

Download the Uconnect™ LIVE

App from the "Apple Store" or "Google

play" on your compatible smartphone,

making sure that the data connection is

enabled.

User not connected

THE Uconnect™ LIVE APP

If the user does not pair the phone with

Bluetooth®, when the Uconnect™

LIVE button is pressed, the radio menu

shows disabled icons, except for eco-

:Drive™.

Further information about the

eco:Drive™ functions is available in

the dedicated paragraph.

The Uconnect™ LIVE App must be

installed on your smartphone to access

the connected services on the car.

This can be used to manage your

profile and customise your

Uconnect™ LIVE experience.

The App can be downloaded from "App

Store" or "Google Play".

Use the Uconnect™ LIVE App to

register on www.driveuconnect.eu

or on the www.fiat.it website.

Start the Uconnect™ LIVE App on

the smartphone and enter your details.

For further information about the

services available in your market, visit

the www.driveuconnect.eu website.

190

For safety reasons, the App cannot be

accessed when the phone is paired

with the radio.

Personal details (e-mail and password)

are required to access the Uconnect™

LIVE radio services, therefore your

personal account is protected and can

only be accessed by the real user.

eco:Drive™

Once sufficient data are available, the

indices will have 5 colours depending

on the evaluation: dark green (very

good), light green, yellow, orange and

red (very bad).

"Current trip index" refers to the entire

value calculated in real time based

on the average of the described

indices.

It represents eco-friendliness of the

driving style: from 0 (low) to 100 (high).

In the event of extended inactivity the

display will show the average of the

indices up to that moment (“Average

index”) then the indices will be coloured

again in real time as soon as the car is

restarted.

To check the data average for the

previous trip (the “trip” starts when the

ignition key is turned to the MAR

position and stops when it is turned to

STOP), select the “Previous Route”

button.

The eco:Drive™ application allows you

to display your driving behaviour in

real time, in order to help you reach a

more efficient driving style as far as

consumption and emissions are

concerned.

In addition, the data can be saved on a

USB flash drive, and the data analysis

can be made on your personal

computer thanks to the eco:Drive™

desktop application, available on

www.fiat.it or www.driveuconnect.eu.

Driving style is evaluated by means

of four indices which monitor the

following parameters:

Connected services that can be

accessed on the vehicle

The Uconnect™ LIVE services

available in the radio menu may change

depending on the market.

The eco:Drive™ and my:Car

applications were developed to improve

the customer's driving experience,

therefore they are available in all

markets where the Uconnect™ LIVE

services can be accessed.

Acceleration

Deceleration

Transmission

Speed

For further information visit the

www.driveuconnect.eu website.

If the navigation system is installed in

the radio, accessing the Uconnect™

LIVE services enables use of the

TomTom LIVE services. Further

information about the LIVE functions is

available in the dedicated chapter.

eco:Drive™ display

Press the eco:Drive™ button to

interact with the function.

The details of the previous trip can also

be displayed by pressing the "Details"

button to show trip duration (time

and mileage) and average speed.

A screen will be displayed on the radio,

showing the 4 indices described above.

These indices are grey until the system

has enough data to evaluate the driving

style.

191

Recording and transferring trip data

NOTES When the USB memory stick is

full, the warning messages are shown

on the radio display.

When the eco:Drive™ data are not

transferred to USB memory stick for a

long time, the internal memory of the

Uconnect™ LIVE system may be

exhausted. Follow the instructions given

by the messages on the radio display.

Settings

Press the

button on the front panel

The trip data can be stored in the

system memory and transferred using a

suitably configured USB memory stick

or by Uconnect™ LIVE App. This

allows you to display the history of the

collected data, showing the complete

analysis of the trip data and of your

driving style.

Further information is available at

www.driveuconnect.eu.

WARNING Do not remove the USB

memory stick nor unpair the

to display the main “Settings” menu.

NOTE The menu items displayed vary

according to the versions.

The menu includes the following items:

Display;

Units;

Voice commands;

Clock & Date;

my:Car

my:Car allows you to keep the

condition of your car always under

control.

my:Car can detect malfunction in real

time and inform the user about the

expiry of the servicing interval. Press

the "my:Car" button to interact with the

application.

The display will show a screen with the

"care:Index" section, which provides

all the detailed information about the

status of the car. Press the "Active

warnings" button (if present) to show

the details of the vehicle's faults which

caused a warning light to switch on.

The status of the car can be viewed on

both the website

Lights (where provided);

Doors & Locks;

Engine Off Options;

Audio;

smartphone and the Uconnect™ LIVE

App before the system has

downloaded the data, otherwise it

could be lost.

Phone / Bluetooth®;

Setup SiriusXM (where provided);

Radio Setup;

During the transfer of data to the

devices, messages may appear on the

radio display to guide the user correctly

through the operation; follow these

instructions. These messages are only

displayed with the ignition key at STOP

and when a delay in the system

switching off is set. The data are

automatically transferred to the devices

when the engine is switched off.

Transferred data will be deleted from

the system memory in this manner. You

can choose to store the trip data or

not, by pressing the "Settings" button

and by setting the storage activation

and the USB or Cloud transfer mode.

Restore settings;

Clear Personal Data.

Navigation (Uconnect™

5" Nav LIVE only)

Planning a route

IMPORTANT In the interest of safety

and to reduce distractions while you are

driving, you should always plan a route

before you start driving.

Press the “Nav” button to show the

navigation map on the display.

www.driveuconnect.eu and using the

Uconnect™ LIVE app.

To plan a route, do the following:

192

tap the screen to open the Main

menu;

NOTE: The navigation system volume

can only be adjusted during navigation

when the system provides voice

indications.

NOTE: the use of a memory stick is

recommended, while the use of mass

storage devices, such as mobile

phones or multimedia players, is not

recommended.

tap "Navigate to" or "Drive to";

tap “Address”. You can change the

country or state setting by tapping

the flag before you select a city;

Updating the map

To prepare a USB device, proceed as

follows:

Two modes for downloading a map

update are available:

enter the town or city name, or the

postcode. Towns with similar names

are shown in the list while you type;

Select “Navigation updates” in the

“Settings” menu. You are asked

whether you wish to prepare a USB

device for downloading updates.

Most recent maps guarantee: if a

new map is available for your system

within 90 days of initial use, you can

download it once free of charge.

enter the street name. Streets with

similar names are shown in the list while

you type. When the correct street

name appears in the list, tap the name

to select the destination;

Select Yes.

Map update: you can purchase a

new version of the map installed on the

system.

To check availability or purchase a map,

make sure that you have prepared a

USB device and installed TomTom

HOME on your computer.

Insert the USB device.

NOTE If the system continues to ask

you to insert the USB device, check

that the device meets the requirements

indicated previously, then retry.

The system starts to prepare the USB

device.

When the USB device is ready, the

following message is displayed.

Remove the USB device and connect it

to the computer. The new map can

now be downloaded to the USB

device.

enter the house number, then tap

“Done”;

if in the Advanced settings menu the

“Show location preview” option is

active, your position is shown on the

map. Tap “Select” to continue or tap

“Back” to enter another address;

Preparing a USB device

To update the map, use a USB device

that meets the following requirements.

when the new route is shown, tap

“Done”. For more information about the

route, tap on “Details”. To change

your route, for example, to travel via a

particular location or to select a new

destination, tap “Change route”;

You are guided to your destination,

using spoken instructions and

Ideally, the USB device should be

empty.

The USB device must have at least

8 GB of memory free.

TomTom HOME installation

To install TomTom HOME and create a

MyTomTom account, proceed as

follows:

The USB device must use a FAT-32

file system.

The USB device must not be

blocked and must allow files to be

saved.

on-screen directions.

193

Download and install the TomTom

HOME application on the computer. On

the computer, access tomtom.com/

getstarted. Select “Download TomTom

HOME”, then follow the instructions

provided.

NOTE If the most recent map is already

installed on the system, the update is

not proposed.

Select the map that you wish to

download, then select “Update and

install”.

The map is downloaded and copied to

your USB device.

Select “Done” when the process is

complete.

NOTE Don’t disconnect the USB device

from the computer while map

downloading and copying is in

progress.

The map can now be installed on the

system.

Keep the device inserted. Before

updating the map, the system indicates

that this process may take several

minutes. Select “OK”.

NOTE Do not remove the USB device

and do not disconnect the system’s

power supply before the update is

complete. The system cannot be used

until the update is completed correctly.

If the update is interrupted, the system

update is started again.

Connect the USB device prepared

with the computer. TomTom HOME

is started automatically.

Select “Enter” in the top right corner

of TomTom HOME.

Once the map has been updated, the

following message is displayed.

Select “Create account” and enter

the required details to create a

MyTomTom account. A MyTomTom

account is required to receive map

updates.

After creating the account, you will be

asked if you want to connect the

Uconnect™ system to your account.

The prepared USB device represents

your Uconnect™ system.

Click on “Close”.

The new map is now available on the

system.

Installing the map

Troubleshooting

After downloading a map to your USB

device, it can be installed on your

system.

IMPORTANT The map update MUST

be made with the vehicle engine

running and may require more than 30

minutes.

IMPORTANT Do not disconnect the

USB device during the map installation

process, otherwise installation will be

interrupted.

The following problems may occur

during the update:

The map on the USB device is not

valid. In this case, download the map to

the USB device again, using TomTom

HOME. It may be necessary to prepare

the USB device again.

Select “Connect device” and then

select “Close”.

A map can now be downloaded to the

USB device.

The version of the map on the USB

device is the same as or is a previous

version of the one already on the

system. In this case, download the map

to the USB device again, using

Downloading a map

Connect the USB device to the

computer.

If a map update is available for the

system, this update is included in the

list of updates available.

Insert the USB device containing the

new map in the Uconnect™ system.

The system detects a new map on

the USB device.

TomTom HOME. It may be necessary to

prepare the USB device again.

Select “Start”.

194

Voice commands

Show SMS

Radio

3D vision

Clear route

NOTE For languages not supported by

the system, voice controls are not

available. To use the voice commands,

press the button on the steering

wheel (”Voice” button) and say out loud

the command you want to activate.

Add Favourite

Repeat instruction

The following voice commands can be

given after pressing the button on

the steering wheel:

Tune to XXX FM

Tune to XXX AM

Global

Tune to Radio XXX

Tune to DAB channel

The following voice commands can be

given after pressing the button on

the steering wheel:

Media

The following voice commands can be

given after pressing the button on

the steering wheel:

Help

Cancel

Repeat

Play song...

Voice Prompts

Play album…

Play artist…

Play genre…

Play playlist…

Play podcast…

Play audiobook…

Select the source

View

Phone

The following voice commands can be

given after pressing the button on

the steering wheel and saying "Go

to telephone":

Call

Dial

Re-dial

Navigation (Uconnect™ 5" Nav LIVE

only)

Call back

Recent calls

Calls made

Missed calls

Calls received

PhoneBook

Search

The following voice commands can be

given after pressing the button on

the steering wheel:

Drive Home

2D view

195

Uconnect™ 7 HD LIVE/ NAV LIVE

.

Controls on front panel

F0S0623

145

196

Front control panel summary table

Button

Functions

Mode

Short button press

Ignition

Switching off

Volume adjustment

Short button press

Left/right rotation of knob

Volume activation/deactivation (Mute/Pause)

Display on/off

Short button press

Exit the selection/return to previous screen

Short button press

BACK

Scrolling the list or tuning to a radio station

Media source track change

Radio station change if in tuner mode

Left/right rotation of knob

SCROLL TUNE

Confirmation of the option displayed

Display the list of stations if in Radio mode

Scroll the contents of the sources if in Media mode

Open the browsing list if in Radio or Media mode

Short button press

197

Summary table of display buttons

Button

Functions

Mode

Radio

Media

Phone

Access to the Radio mode

Press button

Source selection: USB, Bluetooth®

Phone data display

Access the additional functions (e.g. Compass display, Uconnect™

LIVE services)

Uconnect™

Press button

Access to the navigation function

Access the settings menu

Access to the Trip menu

Press button

Nav(*)

Settings

Trip

(*) Uconnect™ 7" HD Nav LIVE versions only

198

Controls on the steering wheel

The controls for the main system functions are present on the steering wheel to make control easier. The activation of the

function selected is controlled, in some cases, by how long the button is pressed (short or long press) as described in the table

below.

F0S0622

146

199

Controls on steering wheel summary table

Buttons

Interaction

Acceptance of incoming call

Acceptance of the second incoming call and putting the active call on hold

Last 10 calls list on the instrument panel (with call browsing active and phone paired only)

Activation of voice recognition

Interruption of the voice message in order to give a new voice command

Interruption of voice recognition

Long press: interaction with Siri, Apple CarPlay and Android Auto

Rejection of incoming call

Ending of call in progress

Exit the display on the instrument panel of the last calls (only with call browsing active)

Short press (Radio mode): selection of next/previous station

Long press (Radio mode): scan higher/lower frequencies until released

Short press (USB, Bluetooth® mode): selection of previous/next track

Long press (USB, Bluetooth® mode): fast forward/rewind until released

Short press (phone mode): selection of next/previous call (only with call browsing active)

Short press: volume increase/decrease in single steps

+/-

Long press: volume continuous increase/decrease until released

200

Switching the system

on/off

“Map": navigation map view

(Uconnect™ 7" HD Nav LIVE

versions only).

At the bottom: display of the following

buttons:

Media mode

Press the "Media" button to select the

desired audio source among those

available: USB, Bluetooth®.

IMPORTANT NOTE Applications used

on portable devices may be not

compatible with the Uconnect™

system

After Media mode is selected, the

following information is shown on the

display:

The system is switched on/off by

pressing the button/knob.

Turn the button/knob clockwise to

increase the radio volume or

anticlockwise to decrease it. The

electronic volume adjustment control

rotates continuously (360°) in both

directions, without stop positions.

“Browse": list of the radio stations

available;

/

: select previous/next

radio station;

“Tune”: manual radio station tuning;

“Audio”: access to the “Audio

Settings” screen.

Radio mode

At the top: information on the track

being played and the following graphic

buttons:

After the desired radio station is

selected, the following information is

shown on the display:

At the top: the list of radio stations

stored (preset) is displayed; the station

currently playing is highlighted.

In the middle: display of the name of

the current radio station and the

buttons for selecting the previous or

next radio station.

On the left: display of the "AM", "FM”,

“DAB” buttons for selecting the desired

frequency band (reconfigurable button

depending on the selected band:

AM, FM or DAB);

Audio menu

“Repeat”: to repeat the track being

played;

To access the "Audio" menu press the

"Audio" button located at the bottom of

the display.

The following adjustments can be

carried out using the “Audio” menu:

“Shuffle”: to play the tracks in

random order.

In the middle: information on the track

being played.

On the left: display of the following

buttons:

“Balance & Fader" (left/right and

front/rear audio balance adjustment);

“Equaliser” (where provided);

Selected device or audio source;

“Speed Adj Volume” (speed-

dependent automatic volume control);

“Select Source”: select the required

audio source.

On the right: display of the following

buttons:

“Loudness” (where provided);

“AutoPlay”;

On the right: display of the following

buttons:

“Auto-On Radio”.

“Info”: additional information on the

track being played;

“Info”: additional information on the

source being listened to;

“Tracks”: list of available tracks.

201

“Map”: navigation map view

(Uconnect™ 7" HD Nav LIVE

versions only).

At the bottom: information on the

track being played and the following

graphic buttons:

NOTE The Uconnect™ system may

not support some USB keys: in this

case, it will not automatically switch

from “Radio” mode to “Media” mode. If

the device used does not play, verify

its compatibility by selecting Media

mode: a dedicated message will

appear on the Uconnect™ system

display.

when requested by the audio

device, enter the PIN code shown on

the system display or confirm on the

device the PIN displayed;

if the pairing procedure is completed

successfully, a screen is displayed.

Answer "Yes" to the question to pair the

Bluetooth® audio device as favourite

(the device will have priority over all

other devices to be paired subse-

quently). If "No" is selected, the priority

is determined according to the order of

connection. The last device connected

will have the highest priority;

an audio device can also be paired

by pressing the "Phone" graphic button

on the display and by selecting

"Settings" or selecting "Phone/

Bluetooth®” from the "Settings"

menu.

IMPORTANT If the Bluetooth® con-

nection between mobile phone and

system is lost, consult the mobile

phone handbook.

NOTE When modifying the name-

device in the Bluetooth® settings of

the phone (where provided), the Radio

may change the track being played if

the device is connected via USB after

the Bluetooth® connection.

Active device or audio source;

/

: select previous/next

track;

Bluetooth® SOURCE

: pause track being played;

This mode is activated by pairing a Blu-

etooth® device containing music

tracks with the system.

“Audio”: access to the “Audio

Settings” screen.

Track selection

PAIRING A Bluetooth® AUDIO

DEVICE

Use this function to scroll through and

select the tracks on the active device.

The choices available depend on the

device connected. For example, on

a USB device, you can also use the

SCROLL TUNE button/knob to scroll

through the list of artists, genres and

albums available on the device,

depending on the information available

in the tracks.

Turn the SCROLL TUNE button/knob to

select the desired category and then

press the button/knob to confirm the

selection.

NOTE The indexing time of a USB

device can vary according to the media

inserted (in some cases it can take a

few minutes).

To pair a Bluetooth® audio device,

proceed as follows:

activate the Bluetooth® function on

the device;

press the “Media” button on the

display;

press the "Select Source" button;

select the Bluetooth® Media

source;

press the "Add device" button;

search for “Uconnect” on the Blu-

etooth® audio device (during pairing, a

screen showing the progress is dis-

played);

202

After updating the phone software, for

proper operation, it is recommended to

remove the phone from the list of

devices linked to the radio, delete the

previous system pairing also from

the list of Bluetooth® devices on the

phone and make a new pairing.

PHONE MODE

The pairing procedure for a mobile

phone is described below: always

consult the handbook for the mobile

phone in any case.

To pair the mobile phone, proceed as

follows:

PHONE MODE ACTIVATION

Press the “Phone” button on the

display to activate the Phone mode.

NOTE To consult the list of mobile

phones and supported functions, visit

the www.driveuconnect.eu website.

Use the buttons on the display to:

activate the Bluetooth® function on

the mobile phone;

press the “Phone” button on the

display;

USB SOURCE

To activate the USB mode, insert the

corresponding device into the USB port

on the central console.

If a USB device is inserted with the

system on, it will start playing the tracks

found on the device.

dial the phone number (using the

graphic keypad on the display);

if no phone is paired with the system

yet, the display shows a dedicated

screen;

display and call the contacts in the

mobile phone phonebook;

display and call contacts from the

registers of previous calls;

access “Settings” and type “Add

device” to start the pairing procedure,

then search for the Uconnect™ device

on the mobile phone;

TRIP COMPUTER

pair up to 10 phones/audio device

to make access and connection easier

and quicker;

Press the "Trip" button on the display to

view the car's trip information.

This function is composed of the

“Instant info” items (“Range” and

“Current fuel consumption”) and the

two separate trips called “Trip A” and

“Trip B” for monitoring the vehicle's

"complete journey" in a reciprocally

independent manner.

Both functions can be reset (reset -

start of a new journey): to reset the

desired "Trip" hold down the "Trip A" or

"Trip B" buttons.

when prompted by the mobile

phone, use its keypad to enter the PIN

code shown on the system display

or confirm on the mobile phone the PIN

displayed;

transfer calls from the system to the

mobile phone and vice versa and

deactivate the microphone audio for

private conversations.

The mobile phone audio is transmitted

through the vehicle’s audio system;

the system automatically mutes the

radio when the Phone function is used.

during the pairing stage a screen is

displayed showing the progress of

the operation;

PAIRING A MOBILE PHONE

IMPORTANT Only perform this

operation with the vehicle stationary

and in safe conditions; this function is

deactivated when the vehicle is moving.

203

when the pairing procedure is

completed successfully, a screen is

displayed: answer "Yes" to the question

to pair the mobile phone as favourite

(the mobile phone will have priority over

all other mobile phones to be paired

subsequently). If no other devices are

paired, the system will consider the first

associated device as favourite.

NOTE After updating the phone

software, for proper operation, it is

recommended to remove the phone

from the list of devices linked to the

radio, delete the previous system

pairing also from the list of Bluetooth®

devices on the phone and make a new

pairing.

FAVOURITES

NOTE On some mobile phones, to

make the SMS voice reading function

available, the SMS notification option

on the phone must be enabled; this

option is usually available on the phone,

in the Bluetooth® connections menu

for a device registered as Uconnect™.

After enabling this function on the

You can add a number or a contact (if

already in Contacts) to the favourite

list during a call by pressing one of the

five "Empty" graphic buttons on the

upper part of the display. The favourites

can also be managed by using the

Phone Book options.

mobile phone, it must be disconnected

and reconnected with the Uconnect™

system in order to make it effective.

TEXT MESSAGE READER

The system can read the messages

received by the mobile phone.

To use this function the mobile phone

must support the SMS exchange

function through Bluetooth®.

If this function is not supported by the

phone, the corresponding "Text" button

is deactivated (greyed out). When a

text message is received, the display

will show a screen where the options

"Read", "View", "Call" or "Ignore" can

be selected.

Press the "Text" graphic button to

access the list of text messages

received by the mobile phone (the list

displays a maximum of 60 messages

received).

SMS MESSAGE OPTIONS

Default SMS messages are stored in

the system memory and can be sent to

answer a received message or as a

new message.

Yes.

MAKING A PHONE CALL

No.

The operations described below can

only be accessed if supported by

the mobile phone in use. For all

functions available, refer to the mobile

phone owner's handbook.

Okay.

I can't talk right now.

Call me.

I'll call you later.

I'm on my way.

Thanks.

A call can be made by:

selecting "Phonebook";

selecting "Recent";

selecting "Dial";

I will be late.

Stuck in traffic.

Start without me.

Where are you?

Are you there yet?

I need directions.

I'm lost.

204

See you later.

APPS MODE

First access to the car

I will be delayed by 5 (or 10, 15, 20,

25, 30, 45, 60) minutes (*).

Press the “Uconnect” button on the

display to access the radio menu

containing all the system application

operations.

Once you have launched the

Uconnect™ LIVE App and entered

your details, you have to pair the Blu-

etooth® with your smartphone and the

radio, as described in the "Pairing a

mobile phone" chapter, to access the

Uconnect™ LIVE services in your

vehicle.

See you in 5 (or 10, 15, 20, 25, 30,

45, 60) minutes (*).

(*) Only use the numbers listed,

otherwise the system will not take the

message.

The menu includes the following items:

"Uconnect™ LIVE";

"Media";

When pairing is complete, the

connected services can be accessed

by pressing the Uconnect™ LIVE icon

on the radio.

Before you can use the connected

services, you must first do the Blu-

etooth® pairing, then complete the

activation procedure by following the

instructions that appear in the Ucon-

nect™ LIVE app.

DO NOT DISTURB FUNCTION

“Phone";

“Settings”;

"Radio";

By pressing the "Do not disturb"

graphic button the user will not receive

notifications in case of incoming calls

or text messages. The user can reply

with a default or customised message

by means of the settings.

"Trip".

Uconnect™ LIVE

SERVICES

Press the Uconnect™ button to

access the Uconnect™ LIVE

applications.

The services available depend on the

car configuration and the market.

To use the Uconnect™LIVE services,

you need to download the

Uconnect™LIVE app from Google

Play or Apple Store and register using

the app or on www.driveuconnect.eu.

SIRI EYES FREE

(available only with iPhone 4S and

subsequent versions and compatible

iOS versions)

Uconnect™ LIVE services setup

using the radio

You can access the the "Settings"

section from the Uconnect™ LIVE

After having paired the Siri enabled

device to Uconnect™, hold the

button on the steering wheel

pressed and then release it.

After the double beep, you can start

interacting with Siri, to listen to music,

get directions, read text messages

and more.

radio menu by pressing the

icon. In

this section the user can check the

system options and change them

according to their preferences.

System updates

If an update for the Uconnect™ LIVE

system is available while the

Uconnect™ LIVE services are being

used, the user will be informed with

a message on the radio screen.

205

201)

Display of the eco:Drive™

my:Car

Press the eco:Drive™ button to

interact with the function.

202)

Connected services that can be

accessed on the vehicle

my:Car allows you to keep the

condition of your car always under

control.

my:Car can detect malfunction in real

time and inform the user about the

expiry of the servicing interval. Press

the "my:Car" button to interact with the

application.

The display will show a screen with the

"care:Index" section, which provides

all the detailed information about the

status of the vehicle. Press the "Active

warnings" button to show (if present)

the details of the vehicle's faults which

caused a warning light to switch on.

A screen will appear on the radio

showing 4 indices: Acceleration,

Deceleration, Speed and Gear. These

indices are grey until the system has

enough data to evaluate the driving

style.

Once sufficient data are available, the

indices will have 5 colours depending

on the evaluation: dark green (very

good), light green, yellow, orange and

red (very bad).

In the event of extended inactivity, the

display will show the average of the

indices up to that moment (“Avg index”)

then the indices will be coloured again

in real time as soon as the car is

restarted.

The eco:Drive™ and my:Car

applications were developed to improve

the customer's driving experience,

therefore they are available in all

markets where the Uconnect™ LIVE

services can be accessed.

If the navigation system is installed in

the radio, accessing the Uconnect™

LIVE services enables use of the "Live"

services.

eco:Drive™

The eco:Drive™ application allows you

to display your driving behaviour in

real time, in order to help you reach a

more efficient driving style as far as

consumption and emissions are

concerned.

In addition, the data can be saved on a

USB flash drive, and the data analysis

can be made on your personal

computer thanks to the eco:Drive™

desktop application, available on

www.driveuconnect.eu.

Apple CarPlay and

Android Auto

(for versions/markets, where provided)

The Apple CarPlay and Android Auto

applications allow you to use your

smartphone in the car safely and

intuitively.

To enable them, just connect a

compatible smartphone via the USB

port and the phone's contents will

be automatically shown on the

Uconnect™ system display.

Recording and transferring trip data

The trip data can be stored in the

system memory and transferred using a

suitably configured USB memory stick

or by Uconnect™ LIVE App.

This allows you to display the history of

the collected data, showing the

complete analysis of the trip data and

of your driving style.

Driving style is assessed by means of

four indices, which monitor the

following parameters: acceleration,

deceleration, gear shift, speed.

Further information is available at

www.driveuconnect.eu.

206

To check the compatibility of your

smartphone, see the indications on the

websites: https://www.android.com/

intl/it_it/auto/ and http://

www.apple.com/it/ios/carplay/.

If the smartphone is connected

correctly to the car via the USB port,

the Apple CarPlay or Android Auto icon

will be displayed in place of the

button in the main menu.

Before using Apple CarPlay, enable Siri

from Settings > General > Siri on the

smartphone.

To use Apple CarPlay, the smartphone

must be connected to the car with a

USB cable.

NOTE Enabling Apple CarPlay/Android

Auto or some functions could require

interaction on the smartphone. If

necessary, complete the step on your

device (smartphone).

If the system's "Nav" mode is already

on, when a device is connected to

the vehicle with a navigation session in

progress, a warning pop-up will appear

on the Uconnect™ system display.

The pop-up allows the user to choose

between using the system navigation

and using navigation controlled by

the smartphone.

The user can choose to change their

selection at any time by accessing the

navigation system that they want to use

and setting a new destination.

Android Auto – app configuration

Interaction

Before use, download the Android Auto

application to your smartphone from

Google Play Store.

The application is compatible with

Android 5.0 (Lollipop) and later

versions.

To use Android Auto, the smartphone

must be connected to the car with a

USB cable.

On the first connection, you will have to

perform the setup procedure that

appears on the smartphone. You can

only perform this procedure with the

vehicle stationary.

After the setup procedure, on

connecting your smartphone to the

car's USB port, the application will run

automatically on the Uconnect™

system.

You can interact with Apple CarPlay

and Android Auto using the steering

wheel controls (long press of the

button), using the SCROLL TUNE

button/knob to select and confirm

or using the Uconnect™ system

touchscreen.

Setting “AutoShow smartphone

display on connection"

Through the Uconnect™ system

settings, the user can decide to view

the smartphone screen on the

Uconnect™ system display as soon

as the smartphone is connected via the

USB port. When this function is set,

each time a connection is made via

USB, the Apple CarPlay or Android

Auto apps will run automatically on the

radio screen.

The "AutoShow smartphone display

on connection" item can be found in

the "Display" submenu.

The function is enabled by default.

NOTES

Navigation

Apple CarPlay – app configuration

With the Apple CarPlay and Android

Auto applications, the user can choose

to use the navigation system on their

smartphone.

Apple CarPlay is compatible with the

iPhone 5 or more recent models, with

the iOS 7.1 operating system or later

versions.

Bluetooth® is disabled while Apple

CarPlay is being used

207

Bluetooth® remains on while

Units;

Select the "My places" button to

create a collection of useful or preferred

addresses. The following items are

always available in "My places": “Home”

and “Recent destinations”.

Android Auto is being used

Voice commands;

Time and Date;

The data connection will depend on

the tariff plan of the smarphone

Safety / Driving Assistance (for

versions/markets, where provided);

This information may be subject to

changes that depend on the

smartphone's operating system.

Select the "Parking" button to

search for car parks.

Lights;

Doors & Locks;

Engine Off Options;

Audio;

Select the "Weather" or "Speed

Camera Warning" button to receive

information on the weather or warnings

about speed camera locations.

NOTE The "Weather" and "Speed

Camera Warnings" functions are only

active if TomTom Services are activated.

Otherwise, the button will appear

greyed out (and the function will not be

available).

Exiting from the Apple CarPlay and

Android Auto apps

With the CarPlay app enabled, you can

still access the contents of the

Phone;

Radio Setup;

Restore default settings;

Clear personal data.

Uconnect™ system by using the

controls available and viewable on its

display. To return to the Uconnect™

system contents with the Android Auto

app enabled, select the last item on

the Android Auto system bar and select

“Back to Uconnect".

To end the Apple CarPlay or Android

Auto session, physically disconnect the

smartphone from the USB port.

NAVIGATION (Uconnect™

7" HD Nav LIVE only)

Press the "Nav" button to show the

navigation map on the display.

NOTE: The navigation system volume

can only be adjusted during navigation

when the system provides voice

indications.

Select the "Petrol Station" button to

search for petrol stations.

Select the "TomTom Services"

button to view the activation state of

the following services (subscription

needed): “Traffic”, “Speed cameras”,

“Weather”, “Online search”.

SETTINGS

Press the “Settings” button on the

display to show the main “Settings”

menu.

Navigation main menu

Select this button to open the

"Settings" menu;

In the navigation view, tap the "Main

menu" button to open the menu:

NOTE

Select the "Search" button to search

for an address, a place or a point of

interest, then plan a route to the

location.

The menu items displayed vary

according to the versions.

The menu includes the following items:

Language;

Display;

Select the "Current trip" button to

delete or edit the planned route.

208

Select this graphic button to

open the "Help" menu. The

"Help" menu contains

Select this button to

The updates can be downloaded from

the maps.mopar.eu website and

installed directly on the navigator in

your car. All updates are free of charge

for 3 years from the start of the

warranty on the car. The navigation

system can also be updated at the Fiat

Dealership (the dealer may charge for

updating the navigation system).

increase/decrease the screen

brightness and display the

map in brighter/darker

colours. When driving at night

or in unlit tunnels, watching

the screen is more

information about the

Uconnect™ system, for

example the map version, the

serial number of the device

and the legal notices.

comfortable and less

distracting for the driver if the

map uses darker colours.

Tip: the device will

automatically switch between

day and night view depending

on the time of day. To

deactivate this function, select

“Appearance” in the

“Settings” menu and deselect

the option "Switch to night

colours" when it is dark.

Select this button to return to

the navigation view.

VOICE COMMANDS

Select this button to

NOTE For languages not supported by

the system, voice controls are not

available.

To use the voice commands, press the

button on the steering wheel and say

out loud the command you want to

activate.

activate/deactivate voice

instructions. Select off to no

longer hear voice instructions.

You will still receive

information such as traffic

information and warning

sounds. Tip: you can

deactivate the warning

sounds by selecting

Global

Map update

The following voice commands can be

given after pressing the button on

the steering wheel:

“Settings”, then “Sounds and

warnings”.

To ensure optimal performance, the

navigation system must be updated

periodically. For this, the Mopar® Map

Care service offers a new map update

every three months.

Help

Cancel

Repeat

Voice Prompts

Phone

The following voice commands can be

given after pressing the button on

the steering wheel:

Call...

209

Dial...

Play podcast…

Play audiobook…

Select the source...

View...

Re-dial

WARNING

Call back

Recent calls

Calls made

Missed calls

Calls received

PhoneBook

Search...

201) Do not carry out other operations

during installation and wait for its

completion, in order not to affect correct

operation of the radio.

Navigation (Uconnect™ 7" HD Nav

LIVE only)

202) Where provided, the my:Car™ app is

not intended to replace the vehicle Owner

Handbook.

The following voice commands can be

given after pressing the button on

the steering wheel:

Find "POI"

Show SMS

Send a text message to...

Show messages

Navigate to “address”

Go to "city name" centre

Navigate to an address

Drive towards a town centre

Navigate home

Radio

The following voice commands can be

given after pressing the button on

the steering wheel:

Go via home

Clear route

Tune to FM "frequency"

Tune to AM "frequency"

Tune to "radio name" FM

Add current position to “My Places”

Display “My Places”

Navigate through a saved location

Recent Destinations

Stop at a recent destination

Increase zoom

Media

The following voice commands can be

given after pressing the button on

the steering wheel:

Zoom out

Play song...

Play album…

Play artist…

Play genre…

Play playlist…

2D view

3D view

Report Speed Camera

Report risk area

210

IMPORTANT Vehicle position tracing

remains active for the assistance

services, where provided, in the event

of accident or vehicle theft, but is not

visible to the customer.

If you receive a text message indicating

that your request was not successful,

you must be aware that the vehicle will

continue to be visible to the registered

customer.

If you have any problems during

activation, consult the FAQ on the

www.driveuconnect.eu portal, contact

the Fiat Dealership or contact Customer

Care.

MOPAR® CONNECT

(where provided)

These services let you keep your

vehicle under control at all times and

receive assistance in the event of

accident, theft or breakdown.

To have these services, install the

Mopar® Connect Device on your

vehicle from the country (list available

on the www.driveuconnect.eu website)

and request activation by following the

instructions received at the email

address given when your vehicle was

handed over to you.

To use the connected services, you

must download the Uconnect™ LIVE

App or access the

www.driveuconnect.eu portal.

You can find all the details about the

services in the Mopar® Connect sec-

tion of the www.driveuconnect.eu por-

tal.

PRIVACY MODE activation

procedure

Proceed as follows:

take note of the total odometer

reading;

make sure that the instrument panel

is off;

Send the following text message to

+393424112613: “PRIVACY

<VEHICLE_CHASSIS_NUM>

<TOTAL_MILEAGE_KM>” (e.g.:

PRIVACY ZFA3340000P123456

12532). You can find the chassis

number in the registration document;

before starting the engine, wait

to receive the text message confirming

that Privacy mode has been activated

and indicating when it expires.

PRIVACY MODE

Privacy mode lets you disable the “Find

car”, “Notify Area” and “Notify Speed”

services, which allow registered

customers to locate their cars, for a

fixed time.

When you have received the

confirmation, you can start your trip in

the knowledge that the vehicle will

not be traced until the indicated expiry

time. If it expires while you are still

travelling, Privacy mode will be

extended until you turn off the engine

(instrument panel off).

211

OFFICIAL TYPE

APPROVALS

All radio equipment supplied with the

vehicle complies with the 2014/53/EU

directive. For further information visit the

websites www.mopar.eu/owner or

http://aftersales.fiat.com/elum/

212

Oil change? The experts recommend PETRONAS Selenia

The engine of your car is factory ﬁlled with PETRONAS Selenia. This is an engine oil range which

satisﬁes the most advanced international speciﬁcations. Its superior technical characteristics allow

PETRONAS Selenia to guarantee the highest performance and protection of your engine.

The PETRONAS Selenia range includes a number of technologically advanced products:

PETRONAS Selenia K Power

Fully synthetic lubricant developed for American design

petrol engines.

PETRONAS Selenia Multipower Gas

Fully synthetic lubricant for petrol engines supplied with methane

or LPG. Protection against valve wear.

PETRONAS Selenia WR Forward

Fully synthetic Low SAPS lubricant for Euro 6 diesel

engines. High fuel economy.

PETRONAS Selenia Multipower C3

Synthetic lubricant for petrol and diesel engines. Fuel economy

characteristics.

PETRONAS Selenia Digitek Pure Energy

Fully synthetic lubricant for petrol engines. High fuel

economy characteristics.

The range also includes Selenia K, Selenia 20K, Selenia Turbo Diesel, Selenia Sport,

Selenia Sport Power, Selenia Racing, Selenia WR, Selenia WR Pure Energy.

For further information on PETRONAS Selenia products visit the web site www.pli-petronas.com

MAINTAIN YOUR VEHICLE IN

TIP TOP CONDITIONS WITH

Mopar Vehicle Protection offers a series of service contracts that are designed to give all our customers the

pleasure of driving their vehicle without any hitch's and concerns.

Our product portfolio consists of a wide and flexible range of extended warranty and maintenance plans

endorsed by FCA. Each with a series of different coverage tiers, in terms of durability and mileage, built to

accommodate you’re driving needs.

Service contracts are made by experts that know every part of your vehicle, and commit themselves

to maintain it in tip top conditions. Our knowledge and passion is tailored around designing

products that promises all our drivers “worry-free driving”.

Only with Mopar Vehicle Protection you are ensured that all service operations are performed

by highly qualified and specialized technicians in authorized FCA repair facilities, using the right tools,

equipment and only original parts, all over Europe.

Check which Service Contract plans are available on your market today and choose the

Service Contract that suits your driving habits best.

Ask your local dealer for further information.

Multimedia for Your Fiat 500 C 2 Door Second Generation (2021-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals