Get Multimedia Guide for Fiat 600 SUV Second Generation (2023-2026)

MULTIMEDIA

This section describes the main

functions of the Uconnect™

10.25"/10.25" NAV infotainment

systems installed on the car.

TIPS, CONTROLS AND

GENERAL INFO ......................... 278

Uconnect™ 10.25"/10.25"

NAV ......................................... 281

CONNECTED SERVICES -

UCONNECT SERVICES .............. 314

RECORDING EVENT DATA ......... 318

SOFTWARE UPDATE ................. 321

REGISTERED TRADEMARKS ...... 322

RADIO FREQUENCY

IDENTIFICATION (RFID)............... 322

OFFICIAL TYPE APPROVALS ...... 323

277

clean with a damp cloth (microfibre if

possible). If necessary, you can use a

delicate mild soap and water solution,

then dry with a soft, dry cloth. Do not

apply pressure on the display lens

do not use alcohol, petrol and

derived products to clean the

display lens and make sure that the

Uconnect™ 10.25"/10.25" NAV

system is switched off during cleaning

prevent any liquid from entering the

system: this could damage it beyond

repair

do not touch the touch screen with

wet hands

Warnings

In the event of an anomaly, the system

must only be checked and repaired by

a Fiat Dealership.

a fault. Otherwise the system might be

damaged. Contact a Fiat Dealership as

soon as possible to have the system

repaired.

TIPS, CONTROLS

AND GENERAL INFO

TIPS

Road safety

MULTIMEDIA DEVICES:

SUPPORTED AUDIO

FILES AND FORMATS

For the USB source the system can

play files with the following extensions

and formats:

Learn how to use the various system

functions before setting off.

Read the instructions for the system

carefully before starting to drive.

345) 346) 347) 348)

Reception conditions

.MP3 (32 – 320Kbps)

.WAV (8/16 bit, 8-48 kHz)

Reception conditions change

constantly while driving. Reception may

be interfered with by the presence

of mountains, buildings or bridges,

especially when you are far away from

the broadcaster.

.AAC (8 – 96KHz) mono and stereo

.M4A (8 – 96KHz) mono and stereo

.MP4 (8 – 96KHz) mono and stereo

For all sources, the system can also

play the following Playlist formats:

.M3U

WARNING The volume may be

increased when receiving traffic

bulletins.

.WPL

If the temperature is particularly low,

the display may take a while to reach

optimum brightness.

For devices that support the MTP

(Media Transfer Protocol), the system

can play back all file and playlist

extensions and formats supported by

the device itself.

NOTE The DAB frequency can be used

in countries where digital transmission

technology is available. The device

will tuned to any frequency if the DAB

button is pressed in a country where

the service is not provided.

If the car is stopped for a while and

the external temperature is very high,

the system may go into "thermal

protection" mode, suspending

operation until the radio temperature

returns to acceptable levels.

NOTE It makes no difference whether

the suffixes are written in capital or

small letters.

Care and maintenance

158) 159)

NOTE It is recommended to load only

unprotected music files, with supported

extensions. If the external audio device

has other formats (e.g. .exe, .cab,

.inf, etc.) problems might arise during

playing of tracks.

Look at the screen only and when it

is necessary and safe. If you need to

look at the screen for a long time, pull

over to a safe place so as not to be

distracted while driving. Immediately

stop using the system in the event of

Observe the following precautions to

ensure the system is fully operational:

avoid hitting the display lens with

pointed or hard objects that could

damage its surface

278

WARNING Some multimedia playing

devices may not be compatible with

the Uconnect™ 10.25"/10.25" NAV

system.

ANTI-THEFT

PROTECTION

The presence of big buildings (or similar

obstacles) may sometimes interfere

with the GPS signal reception.

The system is equipped with an

anti-theft protection system based on

the exchange of information with the

electronic control unit (Body Computer)

on the vehicle.

AUDIO SYSTEM

(according to version)

Only use devices (e.g. USB flash drives)

from safe sources on the car. Devices

from unknown sources could contain

software infected by viruses which,

if installed on the car, could increase

the vulnerability of the car's electric/

electronic systems to hacking.

This guarantees maximum security and

prevents the system from being used

on other cars in the event of theft. In

case of need, contact a Fiat Dealership.

GPS RECEPTION (Global

Positioning System)

The GPS is a satellite system which

provides worldwide information

about time and position. The GPS

is exclusively controlled by the

government of the United States of

America, the only body responsible for

the availability and accuracy of this

system.

EXTERNAL AUDIO

SOURCES

Other electronic devices (e.g. PDA,

etc.) can be used on the car.

334

F6S0117

The vehicle can be equipped with one

of the following audio systems.

Basic

Some of them may cause

electromagnetic interference however.

Disconnect these devices if the system

performance worsens

(1) 2 front tweeters (19 mm diameter)

(2) 2 front mid-woofers (160 mm

diameter)

NOTE The system supports only FAT32

and EX FAT formatted USB devices.

The system does not support devices

with a capacity higher than 64 GB.

NOTE The system does not support

USB hubs connected to the USB port

of the car. Connect your multimedia

device directly to the USB port, using

the specific connection cable for the

device if necessary.

The operation of this navigation system

can be influenced by any change made

to the availability and precision of the

GPS or by specific environmental

conditions.

Medium

(1) 2 front tweeters (19 mm diameter)

(2) 2 front mid-woofers (160 mm

diameter)

When navigation is started for the first

time, the system may require several

minutes to determine the GPS position

and display the current position on the

map. Afterwards the position will be

found much more quickly (usually a few

seconds are needed).

(3) 2 rear full-range speakers (130 mm

diameter)

Premium Sound System

(1) 2 front tweeters (19 mm diameter)

(2) 2 front mid-woofers (160 mm

diameter)

279

(3) 2 rear full-range speakers (130 mm

diameter)

WARNING

(4) 1 subwoofer (160 mm diameter)

(5) 1 center-fill speaker (80 mm

diameter).

158) Only clean the front panel and the

display with a soft, clean, dry, antistatic

cloth. Cleaning and polishing products

may damage the surface. Do not use

alcohol or similar products to clean the

control panel or the display.

A 12-channel amplifier in the load

compartment.

159) Do not use the display as a base for

supports with suction pads or adhesives

for external navigators or smartphones or

similar devices.

IMPORTANT

345) Follow the safety rules here below:

otherwise serious injuries may occur to

the occupants or the system may be

damaged. For safety reasons, always stop

the vehicle before performing operations

that require sustained attention. Some

functions are not accessible while driving.

346) ff the volume is too loud this can

be dangerous. Adjust the volume so that

you can still hear background noises (e.g.

horns, ambulances, police vehicles, etc.)

347) Always follow the highway code

of the country in which you are driving,

and concentrate on the road. Always

drive safely with your hands on the

steering wheel. Only use the Uconnect™

10.25"/10.25" NAV system functions

when you are sure that it is safe to do

so. The customer is liable for all risks

associated with using the functions and

applications of the car. Failure to follow

these rules may cause serious accidents

and/or death.

348) For safety reasons, always stop the

vehicle before performing operations

that require sustained attention. Some

functions are not accessible while driving

280

Uconnect™ 10.25"/10.25" NAV

DISPLAY

335

F6S0118

1. External temperature, climate system settings - 2. Pages - 3. Bluetooth® status, mobile phone signal status, geolocation and

data transfer status - 4. Popup - 5. Customizable areas

281

charge level of the connected

smartphone

system connection status

(Bluetooth®, Wi-Fi, mobile telephone

network)

Restore the sound by pressing one of

the two volume buttons.

:

This system gives access to the

following elements:

Time and exterior temperature.

Heating/air conditioning system

controls and reminders of settings.

Settings for driving aid functions,

comfort and safety functions, audio

equipment and digital instrument panel.

Settings of functions specific to

electric vehicles.

Display of visual manoeuvring aid

functions.

Audio equipment and telephone

controls with display of associated

information.

Incoming call (short press): accept

the call Call in progress (short press):

hang up.

Incoming call (long press): refuse the

incoming call.

Out of call (short press): access the

call log of the telephone connected via

Bluetooth®.

Mirror Screen® connected (short

press): access the projected view of

the telephone application of your Mirror

Screen® equipment.

time

quick access to the Mirror Screen®

functions (associated with a connected

smartphone)

STEERING-MOUNTED

CONTROLS

Connected services and display of

associated information.

/

Radio: automatic search for the

previous/next station (in the list of

radio stations sorted by name or by

frequencies).

Media: previous/next track,

movement in the lists.

Navigation system controls and

display of associated information

(depending on equipment).

Voice recognition (depending on

equipment).

336

JJ000425

Phone: browse the telephone's call

log.

Short press: validation of a selection.

Out of selection, display the lists.

UPPER BANNER

Voice Assistant:

Short press, system voice

Certain information is displayed

permanently in the upper banner of the

touch screen:

commands (depending on equipment).

Long press, voice commands of

the smartphone connected using

Bluetooth® or Mirror Screen® (Apple

CarPlay/Android Auto) via the system.

Increase volume.

outside temperature from the

vehicle's sensors (associated with a

blue symbol if there is a risk of ice)

temperature setting reminder for the

air conditioning

Decrease volume. A long press

mute the sound.

282

on Energy economy mode, refer to the

"Practical information" paragraph.

QUICK ACCESS

FIRST STEPS

WARNING The AM radio selection

mode may be not available on all

vehicles.

350)

338

F6S0207

IMPORTANT

337

JJ000539

The system starts when the ignition

is switched on. With the ignition

off, a press on the button (1)

fig. 338 turns the system on. With

the engine running, a press on the

button mutes the sound. A long

press launches standby mode: the

sound cuts off, the screens go off and

the clock is displayed on the central

screen. Volume control: rotate the

knob.

Under the Uconnect™ 10.25"/10.25"

NAV system two buttons fig.4 are

available for a quick access to:

(1) Home

349) For safety reasons and because

they require sustained attention by the

driver, the following operations must be

carried out with the vehicle stationary and

the ignition on: pairing the smartphone

with the system via Bluetooth®, using

the smartphone, connecting to Mirror

Screen® functions (Apple CarPlay or

Android Auto), changing the system

settings and configuration.

350) Navigation is a driving aid. It cannot

replace the driver. All guidance instructions

should be carefully checked by the user.

By using the navigation, you accept

the following terms and conditions:

automotive/?388448#

(2) Advanced Driving Assistance

System settings (i.e. Speed Limiter,

Cruise Control, Adaptive Cruise

Control, etc.)

GPS NAVIGATION-

APPLICATIONS-

MULTIMEDIA AUDIO

SYSTEM- BLUETOOTH®

TELEPHONE

INFORMATION

This system gives access to the

following elements:

NOTE The functions and settings

described vary according to the version

and configuration of the vehicle, and

according to the country of sale.

349)

audio equipment and telephone

controls with display of associated

information

connected services and display of

associated information

navigation system controls

NOTE A dedicated message is

displayed when the system is about to

go into standby. For more information

283

voice recognition

time and exterior temperature

heating/air conditioning system

controls and reminders of settings

settings for driving aid functions,

comfort and safety functions, audio

equipment and digital instrument panel

settings for functions specific to the

Electric vehicles

display of visual manoeuvring aid

functions

340

F6S0120

341

F6S0121

video tutorials via QR codes (e.g.

screen management, driving aids, voice

recognition).

PRINCIPLES

Use the HOME

Touch buttons

button to display

Display/hide the context menu.

the last used home page, a second

press displays the first home page.

Scroll through the home pages, by

sliding your finger on the screen to the

right or to the left.

Return to the previous page.

NOTIFICATIONS

To change the status of a function,

press the description for the

corresponding line (change confirmed

by the slider moving to the right/left:

function activated/ deactivated).

Swipe down from the upper edge of

the touch screen fig. 339, to access

the notifications centre and display a

list of quick settings: Guest, Privacy,

Brightness, My Devices, Wi-Fi, fig. 340

PRINCIPLE OF

MOVEMENT IN THE

SYSTEM:

Access additional information on

the function.

depending on the pages displayed

on the screen, scroll through the text

or the menu (on the left side of the

screen) by sliding your finger, as with a

smartphone.

Access to a function's settings.

Add/delete shortcuts.

PROFILES

Press the

"Settings" application

Page browsing

In the list, select the "Profile" tab.

The screen display presents a "Guest"

profile built into the system and allows

To browse between pages swipe on

the screen toward right/left. Dots (1)

fig. 341 show that more than one page

is available.

339

F6S0119

284

for the creation and personalisation of

several new profiles associated or not

with mobile devices.

Creation of a new profile allows you to

personalise:

name

A shortcut is a link to a favourite

contact, a favourite radio stations,

climate settings, etc.

The "Guest" profile has a default

display with the possibility of adding

to it and/or returning it to its initial

configuration.

avatar

privacy settings

Tap on a shortcut to open the related

app.

The benefit of creating a new profile is

that you can personalize:

the language, the units, the Privacy

Settings

SHORTCUT CREATION

Custom shortcuts can be created by

the user. To do so:

This profile is built into the system and

cannot be deleted.

go to the desired destination (i.e. list

of destinations in the navigation app,

contacts list, climate settings, etc.)

swipe the screen from left to right or

viceversa to open the shortcut page

push and hold an empty space

for shortcuts or the shortcut to be

substituted. The shortcut page will

disappear

Each profile created can be associated

with a mobile device of your choice

connected via Bluetooth®; the

Bluetooth® function of the mobile

device must first be activated. This

association allows the system to detect

your presence in the vehicle when it

starts and to propose the activation of

your personalised profile.

the screen configuration, the

appearance, the My shortcuts

(depending on equipment)

the audio settings, the favourite radio

stations

the lighting, the interior ambiance

some driving aids, the list of favourites

To edit and delete a profile press on

the graphic button

select the desired destination by

tapping on it.

If a profile is not connected to the

mobile device, the last profile used will

be highlighted.

SHORTCUTS

Swipe on the screen from left to right

or viceversa to open the shortcuts,

fig. 343

Select (+) "Create Profile", fig. 342 to

follow the procedure.

343

F6S0130

342

F6S0122

285

not indicate any malfunction of the

system.

POP-UPS

STORING A RADIO STATION

PRESET

Select a station.

Press the

"Media" application

In the list, select the "Player" tab.

Storing takes place via a short or

long press on one of the

buttons,

or a long press on an existing favourite

radio station, which will be replaced.

345

F6S0123

344

F6S0131

Press the

button to return to the

Press or perform an automatic

search for radio stations.

Or

previous page.

In alternative:

Select "Stations"

Scroll the list for searching the

desired station

In case of notifications (e.g. incoming

calls, messages, etc.) a pop-up, (1)

fig. 344 could appear on the screen.

Press

the button

Enter the frequency values using the

virtual keypad.

Press the

MEDIA

CHANGING SOURCE

Select

add a station as a preset

Press the

"Media" application

Press "Media" to return to the

STATIONS

Using the "Media" application.

A list of stations is available by

pressing the "Stations" tab.

Press the

button to change source

(radio, audio streaming via a USB

socket, Bluetooth® or Mirror Screen®).

SELECTING A RADIO STATION

Press

"Mute" to

activate/deactivate the sound.

NOTE Radio reception may be affected

by the use of electrical equipment not

approved by the Brand, such as a

charger with USB socket connected

to the 12 V socket. The exterior

environment (hills, buildings, tunnels,

basement car parks, etc.) may block

reception, including in RDS mode.

This phenomenon is normal in the

propagation of radio waves and does

Press the

"Media" application

Press the

"Media" application

In the list, select the "Player" tab

fig. 345.

In the list, select the "Stations" tab.

The search is carried out automatically.

Using the steering-mounted controls,

press the button . The search is

carried out automatically.

ACTIVATING RADIO STATION

TRACKING

The system changes frequency

automatically to obtain better reception.

286

If several devices are connected, press

the button to select one.

Press the

"Media" application

In the list, select the "Settings" tab.

Activate "Radio Station Tracking".

The lighting of the slider confirms that

the function is activated.

CHANGING THE RADIO

WAVEBAND

Once the device is connected,

browsing through the files is possible

by pressing the "Playlist" or "Library"

button.

Press the

In the list, select the "Player" tab

Press the button to change the

"Media" application

346

F6S0124

waveband between FM, AM (where

provided), DAB (where provided),

according to the country of sale.

ACTIVATING TRAFFIC

The lighting of the slider confirms that

the function is activated.

AUDIO STREAMING

The streaming function allows you

to listen to the audio stream coming

from the smartphone(s) connected via

Bluetooth®, USB (iPod® type) or Mirror

Screen®.

ANNOUNCEMENTS AND NEWS

ANNOUNCEMENTS

347

F6S0125

This function gives priority to listening

to "Traffic announcements" and "News

announcements" alert messages.

To be active, this function needs

good reception of a radio station that

transmits this type of message.

While traffic information is being

broadcast, the current radio station is

automatically interrupted so that the

message can be heard. Normal radio

listening resumes as soon as the

message is finished.

Short press

next track. Long press: fast forward/

rewind in a track.

go to the previous/

First adjust the volume on the portable

device (to a high level). Then adjust the

volume of the system.

Press

list of selected titles.

repeat the current title or the

If playback does not start, it may be

necessary to start the audio playback

from the smartphone. Control is from

the portable device or by using the

system's touch buttons.

Press

random track playback.

Sound deactivation/

reactivation

NOTE Once connected in streaming

mode, the smartphone is considered to

be a media source.

Press the

"Media" application

In the list, select the "Settings" tab.

Activate "Traffic Announcement (TA)"

and "News Announcement" fig. 346

PLAYING A TRACK

Press the

"Media" application

287

PLAYING A VIDEO

Sound Settings fig. 349

Ambiance sound (sound adapted

to environmental noise), Equalizer

(bass and treble adaptation)

Radio Settings.

To avoid reading and display problems,

we recommend choosing file names

less than 20 characters long that do

not contain any special characters (e.g.

" ? . ; ù).

Volume Settings.

Use only USB memory sticks in FAT32

format (File Allocation Table).

NOTE We recommend using the

original USB cable for the portable

device.

CONNECTIVITY

CONNECTING A WIRED DEVICE BY

USB

The USB connection of a portable

device allows it to be recharged. It

makes its authorised media content

available to the system (Media content

of iPod® type).

348

F6S0132

press the

if several devices are connected,

press the button to select one

"Media" application

349

F6S0126

once the device is connected,

browsing through the files is possible

by pressing the "Playlist" or "Library"

button

INFORMATION AND ADVICE

The system supports USB Mass

Storage devices or Apple devices via

the USB sockets. The adapter cable is

not supplied.

A single USB socket allows the Mirror

Screen connection (Apple CarPlay

or Android Auto) for compatible

connected portable devices and to use

certain applications from the device on

the touch screen.

press

/

to play pause the video

to reverse the video

CONFIGURING SOUND AND RADIO

SETTINGS

Sound settings can be accessed in 2

different ways.

Using the Media application:

Devices are managed using the audio

system controls.

The system will only play audio files

with ".wma, .aac, .flac, .ogg, .mp3"

file extensions, at bit rates between 32

Kbps and 320 Kbps.

The portable device is in charging

mode when connected with the USB

cable.

Press the

"Media" application

NOTE It is recommended that you use

the original USB cables of your devices,

preferably with a minimal cable length

to ensure optimum performance.

160)

In the list, select the "Updates" tab.

Or using the Updates application:

Press the "Updates" button.

It also supports VBR (Variable Bit Rate)

mode.

No other file types (".mp4", etc.) can be

read. ".wma" files must be of the WMA

9 standard. The supported sampling

rates are 32, 44 and 48 KHz.

It is possible to configure:

288

on the device. For example: validations

of the pairing codes

PAIRING PROCEDURE FROM THE

SYSTEM

the vehicle is started once the user

profile has been selected. Automatic

reconnection is put on hold as soon

as the "My Devices" menu is opened.

This is to allow the system to make its

Bluetooth® visible for the connection of

a new device.

Bluetooth® CONNECTION

The Bluetooth® connection of a

portable device to the vehicle's system

provides access to its contents and

"Media" broadcasts. It also enables the

Phone function to be activated.

The connection can be initiated either

from the portable device's Bluetooth®

menu or from the vehicle's system,

which requires opening the "My

Devices" menu for the first connection.

NOTE In some cases, you may need to

unlock your device as well as check

authorization when synchronizing

contacts and recent calls.

Press the

In the list, select the "Connectivity"

tab.

"Settings" application.

The system is disconnected when the

driver’s door is opened and the ignition

is switched off.

Select "CONNECT DEVICE" fig. 350

Selecting "Connect device" it's possible

to connect a phone, access to the last

calls, contacts and use the dialpad to

start a call

If no phone is connected, while

accessing to a phone function the

system shows the following screen

fig. 351

NOTE Some features may not be

supported by your device. For

information on the partial or full

compatibility of device models or

smartphones, please connect to the

Brand’s national website.

Pairing procedure from a device

From the Bluetooth® menu on your

portable device, select the system’s

name from the list of detected devices.

350

F6S0127

Select the name of the portable

351

F6S0128

device you want to connect from the

list of known devices (if the device has

already been connected to the system)

or the list of detected devices (if the

device has never been connected to

the system or previously deleted from

the system).

AUTOMATIC RECONNECTION

The system allows automatic

reconnection of devices already

connected and detected when a user

profile is selected.

WARNING In order to make your

system’s Bluetooth® visible, first open

the "My Devices" menu on the system.

The priority reconnected devices are

those which have been linked to the

selected user profile or, failing this, the

last connected devices

Continue the first connection

procedure proposed by the system and

NOTE A portable device already

connected to the system will be able

to reconnect automatically when

289

WI-FI CONNECTION

using a Mirror Screen® wireless

connection is not possible. In this case,

favour a Mirror Screen® connection

using the USB socket.

Select "My Devices" to display the list

of paired devices.

Press the

"Settings" button

Press "DELETE".

Confirm by pressing "YES".

DEVICE MANAGEMENT

NOTE Some devices that have just

been deleted from the system request

a connection, refuse this request.

For each device already connected to

the system using a wireless connection

(Bluetooth® or wireless Mirror

Screen® connection), it is possible

to determine a preferred connection

mode (depending on the functions the

device can support).

352

F6S0129

WARNING

The system has an external Wi-Fi

connection mode for performing

system updates.

160) To protect the system, do not use a

USB hub.

It is therefore possible to determine

whether the device should be

connected using a wireless Bluetooth®

connection or a wireless Mirror

Screen® connection each time the

system is started once the profile is

chosen.

161) To protect your system, only

networks with a sufficient level of security

are allowed to connect. WPA2 encryption

level, equivalent to a domestic level, is

required.

Press the "Connectivity" application.

In the list, select the "My Device" tab.

Select "Wi-Fi".

Activate/Deactivate "Wi-Fi". The

system starts a search for nearby

Wi-Fi networks. This may take a few

seconds.

USB PORTS

FRONT USB PORTS

Press the

"Settings" application

In the list, select the "Connectivity".

Select "My Devices" to display the list

of paired devices.

The car is equipped with USB-A

(charge only) (1) fig. 353 and USB-C

(data and charge) (2) fig. 353 sockets

for charging the connected device and

playing multimedia content through the

Uconnect™ 10.25"/10.25" NAV

system.

Select the Wi-Fi network to connect

to and enter its password.

161)

Press the

button to manage the

connection of a device.

Choose a connection type then

confirm this choice by pressing

"APPLY".

WARNING Any network already

connected to the system will reconnect

automatically as soon as it is detected

by the system and after having

Refer to the "Multimedia" section

NOTE The sockets must always be

kept clean and dry.

DELETING A DEVICE

previously activated the Wi-Fi function.

Press the "Settings" application.

In the list, select the "Connectivity".

WARNING The Wi-Fi connection of the

system to a device already connected

290

NOTE The sockets must always be

kept clean and dry.

Connect the smartphone to the system

using the USB socket compatible with

Mirror Screen.

MIRROR SCREEN

APPLE CARPLAY SMARTPHONE

CONNECTION

Apple CarPlay is automatically

launched a few seconds after the USB

connection has been established. In

some cases, it may be necessary to

unlock your device.

The smartphone charges when

connected by the USB cable.

NOTE It is recommended that you use

devices’ original USB cables, preferably

with a minimal cable length to ensure

optimum performance.

353

JJ000491

The car can be equipped with an USB-

C (charge only) socket for charging the

connected device.

The wireless connection of a Apple

CarPlay device can be initiated from the

"My Devices" menu.

NOTE The sockets must always be

kept clean and dry.

REAR USB PORT

355

F6S0133

Connecting only one Apple CarPlay

smartphone can be carried out either

by USB cable or using a wireless

connection.

First activate the smartphone’s

Bluetooth® function.

(where provided)

Press the

In the list, select the "Connectivity"

tab.

"Settings" button.

To check the compatibility of

your smartphone, refer to the

indications on the websites:

Select "My Devices" to display the

device to be connected to Apple

CarPlay.

NOTE First activate the CarPlay

function on your Apple smartphone.

Refer to the Apple website in case of

a connection failure of the device to

assess the device’s compatibility with

this function. If the problem persists,

delete all traces of connections on the

smartphone and on the system before

making a new connection.

If the device has already been

connected to the system via

Bluetooth®, select the device settings

from the list of known devices and

choose Apple CarPlay as the wireless

connection mode.

354

JJ000494

The car can be equipped with an

USB-C (charge only) socket fig. 354 for

charging the connected device.

If the device has never been connected

to the system before, it will have to

291

connections on the smartphone and

on the system before making a new

connection.

connection mode. If the device has

never been connected to the system

before, it will have to be paired; refer

to the "Bluetooth® connection"

paragraph. The system detects if

the smartphone is compatible with

Android Auto and offers to connect

to it following the pairing process.

Subsequent automatic connection of

the smartphone requires activation of

the Bluetooth® on your device.

As soon as the connection is

be paired; refer to the "Bluetooth®

connection" section.

The system detects if the smartphone

is compatible with Apple CarPlay and

offers to connect to it following the

pairing process. Subsequent automatic

connection of the smartphone requires

activation of the Bluetooth® on your

device.

Connect the smartphone to the

system using the USB socket

compatible with Mirror Screen®.

Android Auto is automatically

launched a few seconds after the USB

connection has been established.

A validation procedure on the

smartphone has to be followed for

the first connection, with the vehicle

stationary.

As soon as the connection is

established, press the

button to

display the "Apple CarPlay" interface.

Press and hold the steering-mounted

established, press the

button to

display the "Android Auto" interface.

Press and hold the steering-mounted

The smartphone charges when

connected by the USB cable.

NOTE It is recommended that you use

devices’ official USB cables, preferably

with a minimal cable length to ensure

optimum performance.

control button

, say "Siri" to initiate

the smartphone voice commands.

ANDROID AUTO SMARTPHONE

CONNECTION

Connecting only one Android Auto

smartphone can be carried out either

by USB cable or using a wireless

connection.

control button

, say "OK Google"

to initiate the smartphone voice

commands.

PHONE

The wireless connection of a Android

Auto device can be initiated from the

"My Devices" menu.

NOTE To consult the list of supported

phones and supported features contact

Customer Service at the number

listed in the Warranty Booklet or visit

RECEIVING A CALL

An incoming call is announced by

a ring and a display overlaid on the

screen.

To check the compatibility of

your smartphone, refer to the

indications on the websites:

First activate the smartphone’s

Bluetooth® function.

Press the

In the list, select the "Connectivity"

tab.

"Settings" button.

NOTE Install the "Android Auto"

application on the smartphone via "Play

Store". The "Android Auto" function

requires a compatible smartphone.

Refer to the Android Auto website

in case of a connection failure of

the device to assess the device’s

compatibility with this function. If the

problem persists, delete all traces of

Select "My Devices" to display the

device to be connected to Android

Auto. If the device has already

been connected to the system via

Bluetooth®, select the device settings

from the list of known devices and

choose Android Auto as the wireless

Accepting the call:

briefly press the

button on the

steering-mounted controls to accept an

incoming call

292

Select the desired contact in the

displayed list.

Call the contact by selecting one of

the contact's phone numbers pressing

the button.

VOICE COMMANDS

First steps

(depending on equipment)

or press the

Ending the call:

press and hold for at least 2 seconds

touch screen button

The voice recognition language is in

line with the language chosen and

previously configured in the system.

The system supports two languages

for cases where the area in which the

vehicle is travelling is not covered by

the cellular network.

the telephone button on the

steering mounted controls to refuse the

call

ORGANISING THE CONTACT LIST

or press the

button.

Press the

touch screen

Press the

"Phone" application

In the list, select the "Settings" tab to

display the telephone-related settings.

Choose to list the contacts starting

with their first or last name.

CONNECTING TWO PHONES

NOTE The system allows two phones

to be connected simultaneously: 2

via Bluetooth® connection or 1 via

Bluetooth® connection and 1 via Mirror

Screen® connection. Display and

content priority is given to the last

phone used.

button on the touch

screen to send an automatic message

indicating that you are driving.

MAKING A CALL

These languages, referred to as on-

board languages, are downloaded into

the system.

351)

MAKING A CALL USING THE

NUMERIC KEYPAD

If the chosen language has not been

downloaded, a message on the

screen appears as soon as the cellular

network is not connected for the first

time and offers to download it. To

use this new language in all areas,

download it beforehand (ignition on

without starting the engine) via the

Wi-Fi network. Apply the download

procedure displayed on the screen.

Downloading this new language

removes the least used on-board

language

Press the

"Phone" application.

In the list, select the "Keypad" tab

then dial the number.

Press the

button to make the call.

To change the priority of the phone:

MAKING A CALL USING THE LIST

OF RECENT CALLS

Press the "Phone" application.

Press the button to change the

priority of the phone.

Press the "Phone" application. In

the list, select the "Calls" tab.

Or briefly press the telephone button

on the steering mounted controls.

Select one of the last calls in the list,

and make the call.

IMPORTANT

INFORMATION - USING

THE SYSTEM

351) Using the telephone is strongly

discouraged while driving. Park the vehicle.

352) It is always possible to make a call

directly from the telephone; as a safety

measure, first park the vehicle.

352)

When voice commands are activated,

say your command after the audible

signal.

CALLING A CONTACT

Press the "Phone" application.

In the list, select the "Contacts" tab.

293

For commands in several stages,

interaction takes place with the system

to complete the initial request.

sunroof (depending on equipment)

to avoid any external interference,

and switch the ventilation off. Before

speaking the voice commands, ask the

other passengers not to speak.

Voice command example for air

conditioning:

telephone by Bluetooth®", and the

voice session will be closed.

Voice command example for the

weather:

Some commands self-validate after 7

seconds. If the system has not taken

your command into account, it will

indicate this by a voice message and

an on-screen display. If the command

has been accepted by the system, a

visual feedback appears on the display.

"Do I need a raincoat"

"How is the weather tonight"

"What is today's humidity level"

Activating voice commands with

"Hey Fiat"

"Raise the fan speed"

"Turn on air conditioning"

"I'm too hot"

Voice command example for radio and

media:

OPENING VOICE RECOGNITION

Voice commands can be used on any

screen page, provided there are no

other sources which take priority in use

(reverse, emergency or assistance call,

telephone call, other smartphone voice

recognition already launched).

"I want to listen to <singer name>"

"Switch to radio"

"Tune to 88.5"

NOTE Media voice commands are only

available with a USB connection.

Voice command example for

navigation:

The voice recognition can be activated

356

F6S0097

by pressing the button

located on

"Navigate home"

the steering wheel or on the touch

screen or by saying "Hey Fiat".

"Navigate me to Gabrielle's house"

"Search for public parking nearby"

NOTE Depending on the country, give

destination (address) instructions in the

language configured for the system.

Voice command example for

telephone:

In the menu fig. 356 it is possible to

activate/deactivate voice recognition by

saying "Hey Fiat".

To ensure that voice commands are

always recognised by the system,

please follow these recommendations:

use natural language in a normal

tone without breaking up words or

raising your voice. After opening

voice recognition with the button on

the steering wheel or the touch screen

button, always wait for the "beep"

(sound signal) before speaking. For

optimal operation, it is recommended

that you close the windows and the

You can allow the re-use of voice

data to improve the voice recognition

service, fig. 356.

WIDGET

"Call Matthew's mobile"

"Call" <phone number>

"Call Jonathan"

From the home page, press the button

to access the applications wall.

NOTE From any page, press the touch

screen with three or more fingers to

display the applications wall.

NOTE If there is no telephone

connected by Bluetooth®, a voice

message announces: "Connect a

294

Press an app to open it in fullscreen

mode, fig. 357.

The "Statistics" page fig. 358 shows

the energy consumption (light blue)/

recharged (green) in the last 30, 60 and

180 minutes and since the last start.

Mirror Screen®: access the

projected view of Apple CarPlay

or Android Auto. Smartphone not

connected: access the menu allowing

you to connect a smartphone.

Navigation (depending on

equipment): enter navigation settings

and choose a destination. Use services

available in real time, depending on

equipment.

Telephone: access the menu

allowing you to connect a telephone.

Telephone connected: access the call

log, contacts and telephone settings.

Two connected telephones: access the

contents of the priority telephone with

the possibility of changing the priority of

the telephone.

357

F6S0134

ADAS: Advanced Driving

358

F6S0135

Assistance System settings (i.e. Cruise

Control, Adaptive Cruise Control,

Speed Limiter, etc.).

The "Energy Flow" page fig. 359 shows

the energy fluxes from the high-voltage

battery to the electric motor and

regeneration:

Climate: access to on-screen

climate controls.

Help (where provided): access

Date/time: access to date and time

settings.

Electric motor (1): in light blue if

power is requested from the high

voltage battery (traction), in green when

the vehicle decelerates or brakes and

the high-voltage battery is recharged

(regeneration). Same colours are used

to highlight the high-voltage battery (2)

and the front wheels (3) in the same

conditions.

the handbook through QR code

available on the display.

"ENERGY" WIDGET

(where provided)

The "Energy" widget shows the

following information:

Energy (Electric versions): shows

the statistics of usage of the high-

voltage battery.

Hey Fiat (depending on equipment):

use the system Voice Assistant or the

smartphone Voice Assistant via the

system.

Energy Flow: energy fluxes from

the high voltage battery to the electric

motor and regeneration

Statistics: energy consumption/

recharged

High-voltage battery (2): the

Settings: main settings for the audio

system, touch screen and digital

instrument panel.

highvoltage battery charge level is

indicated by set of 8 green bars. The

more coloured bars there are, the

greater the battery charge state.

Charging: to set the time for the

scheduled charging

Media: select an audio source or

radio station.

295

359

F6S0136

The "Charging" page fig. 360 shows

the time set for the scheduled

charging. The time can be set through

the FIAT® app. Once the time is set

and the recharging cable is connected

to the charging port, the scheduled

charging feature must be activated

through the FIAT® app or pushing the

button next to the charging port.

360

F6S0137

296

NAVIGATION

NAVIGATION HOME SCREEN

(depending on equipment)

361

F6S0138

297

NOTE Using the graphic keypad is only

allowed when the car is stationary in

some countries. If an attempt is made

to enter text (e.g. an address) with the

car in motion or if driving is resumed

without having completed engagement,

a specific warning message will appear

on the display and the operation will be

ended. You can also drive more safely

by using voice commands to control

navigation.

353) 354) 355)

You can use map view in the same way

as you might look at a traditional paper

map. You can move around the map

using gestures, and zoom using the

zoom buttons.

Important: Everything on the map is

interactive including the route and the

map symbols. Try selecting something

and see what it does.

362

F6S0139

PERSONAL INFORMATION &

PRIVACY

By pressing on the graphic button

You can find your destination by

selecting it on the map, by choosing

a saved destination (e.g. "Home" or

"Work") or by searching for an address

using the "Search" button in the main

menu.

“Learn more” it’s possible to visualize

on the display the detailed information

related to:

At the first startup of the navigation

system or after a change of profile

and/ or system language, a request of

saving information sent by TomTom

on the Uconnect™ system is shown

fig. 362 . Some services/option

provided by the navigation system

need the activation of the "Save journey

history on your device" function.

Activate the function “Save journey

history on your device”, sliding the

graphic cursor (1) fig. 362 to the right

to activate the function and then press

on the graphic button “OK”.

“General”

"TomTom Services"

“Other uses of your data”

“Journey history”

After selecting the destination, a route

is planned and displayed on the "Map

View" screen. On the right-hand side

of the display is the route bar, which

provides an additional indication of

events along the route, such as

accidents and speed cameras. The

arrival time and remaining distance are

also available.

Press on the graphic button (1) fig. 363

on the right side of the display to show

the information.

You can choose to view the route via a

3D image in the "Guidance view".

NOTE The navigation system volume

can be adjusted during navigation

when the system provides voice

indications or using the "Volume

adjustment" function "Audio settings"

menu.

363

F6S0140

298

MAIN MENU

Select "Settings" to enter the vehicle

type and to personalise the display,

voice instructions, map options, trip

planning, sounds and alerts, and

system information.

matching addresses and POIs are

shown.

Press the

"Navigation" application

2: Destination entry box. Enter here

through the graphic keyboard the

destination (address, city or country)

3: Type of search.By default, the

whole of the current map is searched.

Once you have used search, the last

search type you selected is used.

Select this button to change the type of

search

to display the navigation home screen

fig. 361.

Press the

menu of the various options.

Press "Search" to enter an

button to display the main

NOTE Regular connection to a Wi-

Fi terminal automatically updates the

map.

address, name or certain points of

interest.

The mapping update can also be

carried out via a cellular network,

depending on version, depending on

country of sale, depending on the level

of equipment of the vehicle, as well as

the subscription to connected services

and options.

Select

"Go home" using an

address previously saved in "Add

home".

4: Cancel search button. Select this

button to return to the map view or

guidance view

Select

"Go to work" using an

address previously saved in "My

places".

5: Keypad switch button. Select this

button to switch between a keypad

with letters and numbers, and a keypad

with numbers and symbols.

NAVIGATION MAP VIEW

Select

"Recent destinations"

Push the "Navigation"

graphic

to display the latest destinations

searched.

button to show the navigation map on

the display

DESTINATION RESEARCH

To search a destination, press the

graphic button “Search” on the

navigation map.

6: Confirmation button. Select this

button to confirm the destination data

entered.

Select

"Current trip" (if navigation

is ongoing) to open another menu and

perform various actions on the current

route planned.

Select

"My places" for quick

ATTENTION in the interest of safety

and to avoid distractions while driving,

you must always plan the route before

you start driving.

access to saved places as well as

favourite destinations.

Select

preferred routes

"My trips" to display the

On the screen, fig. 364 are shown

the following graphic buttons:

1: Back button. Select this button to

return to the previous screen.

2: Search input box. Enter your

search term here. As you type,

Select

"Weather" (present when

navigation is connected and when no

trip guidance ongoing) to display the

daily and hourly weather forecast for 5

days around the vehicle and for chosen

cities.

299

3: Destination address.

1

4

4: Drive button. Click on this button

to choose your route and go to the

guidance view. The shading of this

button also represents the time left

to choose another route. If you get to

this screen and do not choose another

route, the first route will automatically

be chosen after few seconds.

5: Current location.

1

2

3

6

5

366

F6S0144

364

F6S0141

6: Route details panel. This panel gives

you, for the chosen route:

The arrival time

To hide the keayboard press (7)

fig. 365

The distance

Any delay on the route (such as

traffic jams, roadworks) that affect your

arrival time

Drive

2

Icons that represent specific

features of the route, such as tolls, or

motorway, or tunnels, that may affect

your journey.

367

F6S0143

7

It’s possible to choose any one of the

three routes shown. As you do this, the

route is highlighted on the map.

Route selection

365

F6S0142

When a destination is chosen and the

graphic button (2) fig. 367 is pressed,

the route selection screen appears

fig. 368

NAVIGATION STARTING

3

4

When you have chosen a destination, it

appears on the display (1) fig. 366

Pressing on the destination will

7

mins slower

From here, you can select your

preferred route from the three options

that are given to you.

1

Drive

be possible to show the related

9

mins slower

information (address and expected time

of arrival) and start the navigation (by

pressing the graphic button (2) fig. 367

1: Destination

5

6

2: Your route. If more than one route

is available, all the possible routes are

shown. The fastest route is highlighted.

2

368

F6S0145

300

an arrival information panel at the top,

and a bar with symbols underneath It

is possible to hide the route bar in the

guidance view, see Settings.

The guidance view

The guidance view is the default view

for your TomTom Navigation.

(2): graphic button “Navigation map”.

Push this graphic button to change the

visualization of the navigation map.

(3): graphic button activation/

The guidance view is shown when

you have selected a route form the

route selection screen. You see your

current location and details along your

route, including 3D buildings in some

cities. The guidance view is normally in

3D direction up. Use the switch view

button (5) fig. 369 to change between

3D direction up, 2D direction up, and

2D north up.

deactivation navigation vocal

4: End route button. Use this button to

cancel your route.

instructions. Press the graphic button

to activate/deactivate the instructions

provided by the vocal assistant during

the navigation.

5: Mute button. Select this button to

choose between audio instructions,

warning only or no sound.

6: Switch view button. Select the

switch view button to change between

the 3D direction up, 2D direction up,

and 2D north up.

Search

CA Italy

7: The Options button. Click on this

button to go to the route options panel,

where you can modify and get an

overview of your current route

Dynamic range mapping

2

3D

!

3

1

CA Italy

3D

!

1

3

2

6

Dynamic range mapping visualises the

vehicles realtime range on the Route

bar (3), as well as the nearest charging

station/fuel station.

370

F6S0147

End

Navigation Map centering

7

4

5

To re-center the navigation map in the

middle of the screen press the graphic

button "Re-centre", fig. 371

The driver will be prompted to search

for a charging station if battery is

running low or for a fuel station if fuel is

running low.

369

F6S0146

1: Next instruction. This gives details of

your next junction, the name of the next

road, and the distance to the junction

or manoeuvre.

Map graphic settings

On the lower zone the following graphic

buttons are shown fig. 370

Re-centre

2: Current location. This symbol shows

your current location. Select it to add

it to My Places or search near your

current location.

(1): graphic button “Options”. Press

the button to show the Navigation

options.

Re-centre

3: Route bar. The route bar is shown

when you have planned a route. It has

371

F6S0148

301

the Destination entry box (2) fig. 364

and press the Confirmation button.

Add a Point Of Interest as a stop on

the route

Navigation stop/resume

To stop the navigation press the

graphic button “End” on the display

and confirm by pressing the “OK”

button on the screen.

Restaurants

Add Stop

When a route is selected, press on the

route to open the side menu shown in

fig. 372

To not confirm and resume the

navigation press “Resume”.

By checking the message “Don’t show

this message again” the message

won’t be shown the next times a

navigation in cancelled.

ROUTE PLANNING VIA POI (Point

Of Interest)

This function allows to reach or add

to the route one or more Points of

Interest, choosing from the list shown

on the display.

Press one of the quick buttons (1) or

the

POI.

button to search for the desired

373

F6S0150

ROUTE PLANNING ON THE MAP

To plan a route through the map, open

the map and do a long press on the

destination you want to select.

To switch from list to map view, press

on the screen.

ADD STOP

1

Change Route

Show Instructions

End

Points Of Interest (POI) categories

On the screen are shown the following

Points of Interest (POI) categories:

Parking

Charging stations (where provided)

Restaurants

Bar

RECENT DESTINATIONS

To plan a route to a recent destination,

proceed as following:

372

F6S0149

Press the graphic button (1) fig. 374:

on the screen will be shown the list of

the last destinations

Select the desired destination:

pressing on it the navigation will start

Once the desired POI is selected, on

the screen will be shown the details

(fig. 373).

Hotel/Motels

Hospitals

Press “Add Stop”.

Tourist attractions

Commercial centres

Cash dispensers

Airports

Car dealers

Pharmacies

Use a Point Of Interest as a

destination

Type the name or category of POI in

302

The function allows to select the

following option (shown on the right

side of the display), fig. 376:

1

My Places

Add Home

“Show Alternatives”: allows to search

for an alternative for the selected route

“Avoid Part of Route”: allows to avoid

part of the selected route

Add Work

Recent destinations

Current Location

Add

BRITISH ENGLISH

Change Route

Show Alternatives

377

F6S0154

374

F6S0151

Avoid Part of Route

Reorder Stops

Current Location

City

Country

Zip Code

Geographical coordinates

NOTE By pressing on the graphic

button “Edit list”, placed on the lower

part of the display, it’s possible

to modify the list of the recent

destinations.

CHANGING DESTINATION

During the navigation touch the route.

On the side menu select “Change

Route”fig. 375

Adding of a POI to “My Places”

Proceed as follows:

376

F6S0153

FAVOURITES (My Places)

Select the category of the desired

POI: the POI will be shown on the

screen, fig. 378

Through the menu “My places” it’s

possible to select one of the following

options,fig. 377

Select “Add to My Places”

“Add Home”: adds to “My places” list

the home address

“Add Work”: adds to “My places” list

the working place address

“Recent destinations”: adds to “My

places” list the recent destinations

“Current Location”: adds to “My

places” list the current location address

NOTE Selecting “More” it’s possible to

visualize on the screen the information

related to the selected POI (i.e. name,

city, address, phone number - where

available, web address - where

available, email – where available).

ADD STOP

Change Route

Show Instructions

End

1

375

F6S0152

303

route isn't planned, the map shows car

parks near your current location.

To see a list of car parks near your

destination, click on the search bar at

the top of the screen.

To find a charging station, type

“Electric Vehicle Charging Station” in

the Search input box (2)fig. 364 or

select the “Electric Vehicle Charging

Station” POI from the POI list. The list

with the charging stations found is

shown fig. 380 and it can be displayed

on the map by clicking on the icon

.

Shopping Centres

Add to My Places

More

AAA AAAA

Drive

You can select a car park from the list

to locate it on the map.

Tip: You can scroll down the list of

results using the scroll bar on the right

side of the screen.

378

F6S0155

If you want to change how the search

is done, select the button to the right of

the search box. You can then change

where the search is carried out, for

example, to search near you or the

whole map.

CAR PARK SEARCH

Electric Vehicle Char.

Important: in the interest of safety and

to avoid distractions while driving, you

must always plan the route before you

start driving.

2: Select a car park from the map or

the list. A pop-up menu opens on the

map showing the name of the car park.

To plan a route to your chosen car

park, select the “Drive” button.

A route is planned and then guidance

to your destination begins. As soon as

you start driving, the guidance view is

shown automatically.

To find a car park, do the following:

1: Select the POI “Parking” symbol.

The map opens showing the locations

of car parks fig. 379

380

F6S0157

If a route is planned, the map shows

charging stations near your destination.

If a route isn't planned, the map shows

charging stations near your current

location.

P

Parking

FINDING A PUBLIC CHARGING

STATION

(Electric versions)

It’s possible to change the screen to

show a list of charging stations by

pressing the button (1).

It’s possible to select a charging station

from the list to find it on the map.

Tip: It’s possible to scroll down the list

of results using the scroll bar on the

right side of the screen.

WARNING In the interest of safety and

to avoid being distracted while you are

driving, you should always plan a route

before you start driving.

379

F6S0156

If a route is planned, the map shows

car parks near your destination. If a

304

is shown an alert that suggests to the

driver to stop for a recharge, fig. 382.

Press the graphic button “Search” to

search for a recharge station or the

graphic button “Cancel” to cancel the

search.

Select a charging station from the

map or list, (1) fig. 381. A pop-up menu

opens on the map showing the name

of the charging station

To plan a route towards the selected

charging station, select the "Drive”

button. A route is planned and then

guidance to your destination begins. As

soon as you start driving, the guidance

view is shown automatically

Rivoli

Charging connectors

Grugliasco

Domestic plug

Industrial Blue

Industrial Red

Type 2 Mennekes

Type 3

Recharging needed to reach your destination. Find

a

charging station along the route? Search

Recharging needed to

383

F6S0160

reach your destination.

Find a charging

station?

Search

Cancel

FINDING A PETROL STATION

Torino

WARNING In the interest of safety and

to avoid distractions while driving, you

must always plan the route before you

start driving.

Electric Vehicle Charging Station

bluetorino Torino Via Nichelino

Bruino

600

m

Via Nichelino, 10135 Torino

Blangiotto

Regular - 22 kW

Orbassano

Rivalta di Torino Via Savona

9.8 km

Via Savona, 10040 Rivalta di Torino

Slow - 11 kW

382

F6S0159

1

CHARGING CONNECTOR

(Electric versions)

To find a petrol station, do the

following:

Select "Settings" and then "Vehicle

Profile" in the Main Menu, then select

"Charging connectors", fig. 383.

It’s possible to choose the correct

charging connector to be used when

searching for a charging station. The

charging connector supplied with the

car is already selected.

1: Select “Petrol Station” POI symbol.

The map opens showing the locations

of petrol stations. You will also see the

fuel price, if the navigation is connected

and if available.

381

F6S0158

Tip:It’s possible add a charging station

as a stop on your route by using the

popup menu. The charging stations

that are set as a stop on your route

have a blue icon.

If a route is planned, the map shows

petrol stations along your route. If

a route isn't planned, the map shows

petrol stations near your current

location.

Recharge to reach the destination

If the vehicle high-voltage battery

is almost discharged it may not be

possible to reach the destination.

In this case on the screen is shown a

dedicated message: on the right side

To see a list of petrol stations near your

destination, click on the search bar at

the top of the screen.

You can select a petrol station from the

list to locate it on the map.

305

Tip: It’s possible to scroll down the list

of results using the scroll bar on the

right side of the screen.

In this Map & Display menu it is also

possible to activate/deactivate the

autonomy radius view on the map,

that shows the reachable distance

depending on the fuel amount or

high-voltage battery charge level.

The view show also the nearest fuel

station/charging station.

If you want to change how the search

is done, select the button to the right of

the search box. You can then change

where the search is carried out, for

example, to search near you or the

whole map.

Routing

2: Select a petrol station from the map

or the list. A pop-up menu opens on

the map showing the name of the

petrol station.

It allows to select the preferred

route type (assorted, fast, short or

Eco-friendly), the kind of road to avoid

(toll roads, unpaved, motorways, etc.)

and the rerouting options (automatic,

manual, never reroute, etc.).

384

F6S0161

Map & display

It allows to select the downloaded

maps and choose the contents shown

on the screen:

To plan a route to your chosen petrol

station, select the “Drive” button.

A route is planned and then guidance

to your destination begins. As soon as

you start driving, the guidance view is

shown automatically.

Preferred route types:

Downloaded maps: for choosing

which map to show on the screen

Day & night colours: for choosing the

colours of the display (day/night/ switch

automatically)

Show on map: for choosing the

contents shown on the map, like POI,

3D buildings, junction details, etc.

Arrival info: for choosing the details of

the destination (arrival time, remaining

distance, etc.)

Fastest route: the fastest route

to your destination. Your route is

constantly checked taking into account

the traffic conditions.

Shortest route: the shortest route to

your destination. This may take much

longer than the fastest route

Most eco-friendly route: the most

fuel-efficient route

Rerouting options:

Tip: You can add a petrol station as a

stop on your route by using the pop-up

menu. A petrol station that is a stop on

your route has a blue icon.

SETTINGS

The “Settings” menu,fig. 384 allows to

define the following settings:

Map & display”

Routing”

“Alerts & sounds”

“Vehicle profile”

“Other”

Side bar: for choosing the

Automatic. Always take the fastest

route - the fastest route will always be

chosen for you.

Manual. Ask me so I can choose -

you will be asked if you want to take

the faster route. You can manually

select the faster route or you can select

the route by steering towards it.

information shown on the side bar

(parkings, charging stations, rest areas,

etc.)

Zoom & orientation: for choosing

the type of dynamic zoom during the

navigation (at instruction, based on

road type, no auto zoom, etc.)

306

your navigation system, including:

Software version

Installed map

Never. Don't reroute me – your

device will not find faster routes for you

Alerts & sounds

Legal information.

THE ROUTE BAR

The route bar is shown when you

have planned a route. It has an arrival

information panel at the top, and a bar

with symbols underneath

It allows to define what kind of acoustic

information are given during the

navigation (street names and numbers,

traffic guidance, road signs, etc.) and

what kind of alerts are given (visual,

visual and sound, etc.).

Vehicle profile

(Electric vehicles)

WARNING the remaining distance

shown by the route bar depends on the

overall length of the route.

It allows to set the type of charging

connector installed on the vehicle to

find the right charging station during

the navigation.

Other

It allows to set the privacy options and

read about the copyright and legal

information.

385

F6S0162

Privacy settings:

Record trip history: select this setting

to choose if your trip history stays in

the navigation system.

The arrival information panel shows the

following information:

The estimated time that you will

arrive at your destination.

The length of time to drive to the

destination from your current location

The bar uses symbols to show the

following information:

Predict frequent destinations: select

this setting to choose if your navigation

system suggests frequent destinations

when you are planning a route.

Frequent destinations: select this

to see a list of your stored frequent

destinations. You can then choose

which ones you want the navigation

system to forget.

The stops on your route.

The next petrol stations that are

directly on your route (depending on

navigation settings)

About

This screen gives you information about

307

Traffic incidents

Speed cameras (where this service is

available)

Receive alerts that signal fixed

camera zones

Availability

Brand

Address information, opening hours,

payment method

Receive updated alerts, sent by a

unique community of drivers in Europe

Community input, share and report

real time Speedcams on your road

ahead. Avaibility depends on country

legislation.

You can choose the information

you see on your route through the

navigation settings.

Online search address and Points

Of Interests (POI)

The symbols are in the order that they

occur on your route.

Millions of useful Points Of Interest

(POI) globally can be searched:

Search by a nearby address, zip

code or a destination

Online traffic

The total time delay due to traffic jams,

weather, and other incidents on your

route, is shown above the symbols.

The bottom of the route bar represents

your current location and shows the

distance to the next item, such as a

traffic incident or petrol station, on your

route.

Data is updated every 30 seconds. It

guarantees access to the most up-to-

date and accurate traffic information to

help drivers arrive at their destinations

faster, more safely and more reliably,

regardless of their location.

The database is updated in real time.

Off street parking

The feature shows parking lot locations

nearby, along the route or near the

destination, including:

The navigation system regularly

receives information about the

changing traffic conditions. If traffic

jams, heavy rain, snow or other

incidents are found on your current

route, the navigation will offer to re-plan

your route and avoid any delays.

Charging station finder and real

time availability

Real-time availability

Opening hours

Available services

Prices

Local weather

TomTom SERVICES

(where provided)

Depending on country, TomTom offers

a selection of services that helps the

driver during the route planning and

driving.

Drivers have access to daily and hourly

weather information at their fingertips,

including:

Fuel prices

Five-day weather forecasts for towns

and cities

Daily high and low temperatures,

wind speed direction and amount of

precipitation

Search and display fuel stations on

the road or on the entire map. The

information shown includes prices,

location, brand and opening hours.

TomTom Alert Service and

Speedcams

(Electric versions)

The function finds available locations

and make informed decisions about

when and where to charge. The system

will prompt automatically with a list

of charging stations compatible to

your car. For each charging station is

shown:

Over-The-Air map updates

The vehicle’s map of the region in

which you drive is continually updated

through a seamless over the air

connection.

The service warns drivers about what’s

coming ahead, reducing stress and

increasing safety.

308

to navigate to one of the destinations

by saying “Hey Fiat, navigate to”

This ensures the system is always up-

to- date and responsive for the best

navigation experience.

For optimal operation, it is

recommended that you close the

windows and the sunroof (depending

on equipment) to avoid any external

interference, and switch the ventilation

off. Before speaking the voice

commands, ask the other passengers

not to speak.

followed by one of the destinations

shown on the screen (e.g.: “Hey Fiat,

navigate to petrol station nearby”.

The command will be confirmed by a

popup and the navigation will start. If

available, it’s possible to call the phone

number associated to the destination

by touching the symbol (2) fig. 386.

Drivers receive the most up-to-date

information available automatically,

eliminating manual map updates.

Access to additional information

regarding the connected navigation

services

Voice command example for

navigation:

"Navigate home"

"Navigate me to Gabrielle's house"

"Search for public parking nearby"

NOTE Depending on the country, give

destination (address) instructions in the

language configured for the system.

For example, by saying “Search for a

nearby petrol station”, the navigation

system will show the following screen,

fig. 386

IMPORTANT

353) Death or serious injury could result

from failure or partial failure to follow

these warnings and instructions. Failure

to properly set up, use, and care for this

device can increase the risk of serious

injury or death, or damage to the device.

354) It is your responsibility to use best

judgment, due care and attention when

using this device. Don't allow interaction

with this device to distract you while

driving. Minimise the time spent looking at

the device screen while driving. You are

responsible for observing laws that limit

or prohibit the use of mobile phones or

other electronic devices, for example, the

requirement to use hands-free options for

making calls when driving. Always obey

applicable laws and road signs, especially

those relating to your vehicle’s dimensions,

weight and payload type. TomTom does

not guarantee the error-free operation of

this device nor the accuracy of route

suggestions provided and shall not be

liable for any penalties arising from your

stellantis-connected-nav/

NAVIGATION WITH VOICE

COMMANDS

The voice recognition can be activated

by pressing the button

located on

the steering wheel or on the touch

screen or by saying "Hey Fiat". Then

say the command.

NOTE To ensure that voice commands

are always recognized by the system,

please follow these recommendations:

use natural language in a normal

tone without breaking up words or

raising your voice. After opening voice

recognition with the button on the

steering wheel or the touch screen

button, always wait for the "beep"

(sound signal) before speaking.

386

F6S0163

Touch the symbol (1) fig. 386 to

navigate directly to the selected

destination. In alternative, it’s possible

309

Profiles: edit/create a profile

Customisation: ambient lighting,

sound ambiance, screen animations

Connectivity: pair new device,

connect to Wi-Fi, privacy settings

System settings: general settings

regarding language, units, etc.

Screen brightness

(see the meaning of the "Privacy" icons

in the "Privacy Settings" paragraph).

Press to edit an existing Profile.

Press "+ Create a new profile" to create

a new Profile.

failure to comply with applicable laws and

regulations.

355) Devices without a truck or camper

map installed will not provide appropriate

routes for oversized/ commercial

vehicles. If your vehicle is subject to

weight, dimension, speed, route, or

other restrictions on a public road then

you must only use a device that has a

truck or camper map installed. Your

vehicle specifications must be entered

accurately on the device. Use this device

as a navigation aid only. Do not follow

navigation instructions which may put you

or other road users in danger. TomTom

accepts no liability for damages resulting

from your failure to observe this notice.

CUSTOMISATION

It's possible to customize:

the screen colour:

select "Screen colour"

Audio settings

Vehicle settings: internal/external

lighting, vehicle access, safety, etc.

Updates: check for existing system

updates and start updating

browse through the available

colour palettes and chose one by

pressing on it

a "tick" sign

selection

press on

confirms the

PROFILE

Each profile created can be associated

with a mobile device of your choice

connected via Bluetooth®; the

Bluetooth® function of the mobile

device must first be activated. This

association allows the system to detect

your presence in the vehicle when it

starts and to propose the activation of

your personalised profile.

to return to

"Customisation" menu

the ambient lighting (where provided):

select "Interior colour"

SETTINGS

The "Settings" widget, fig. 387 allows

to define the main system settings.

browse through the available

interior lights colours and chose

one by pressing on it

the preview on the screen

confirms the selection

NOTE Depending of the conditions of

the vehicle, it may occur that in some

specific cases the privacy settings

previously linked to a profile could not

be loaded. Please always check the

"geolocation and data transfer status"

icon screened in the upper banner of

the Uconnect™ 10.25"/10.25" NAV

(see (3) fig. 335) when changing profile

and at the end of each profile creation

press on

"Customisation" menu

the sound ambience

the visual welcome and goodbye

animations

the screen transition animations

CONNECTIVITY

It is possible to manage:

My Device: pair a new device (see

"Connectivity" section)

to return to

387

F6S0122

Select a page on the left side to define

settings regarding:

310

Wi-Fi: connect to a near Wi-Fi

network

Privacy: define the privacy settings

for sharing data and location

SYSTEM

It is possible to configure:

the language

the date and time

the unit of distance and consumption

(kWh/100 miles - miles, mi/kWh - miles,

km/kWh - km)

Press the back arrow to return to the

previous page.

Press the "Time Settings" line then

set the time.

Radio settings:

FM radio list order: alphabetical/

by frequency

Radio station tracking for

searching the best frequency

Traffic announcements settings

and type of announcements

allowed

Press "OK" to confirm.

Press the "Date" line then set the

date.

Press "OK" to confirm.

Select the Time Format (12h/24h).

Select the Date Format.

NOTE The system does not

automatically change between winter

and summer time (depending on the

country of sale).

Volume settings:

Volume of the voice speech

Volume of telephone ringtone

and voice volume

Volume of acoustic notifications

from the system

Volume of navigation

the temperature unit (Fahrenheit,

Celsius)

It is also possible to reset the system

configuration and view the system

version.

BRIGHTNESS

Slide the cursor to increase/decrease

the brightness.

information (where provided)

VOICE ASSISTANT (HEY FIAT)

It is possible to configure:

The activation of the Voice Assistant

via the wake-up word "Hey Fiat"

The authorization to share with the

Voice Assistant service provider the

personal data stored in the system to

improve the Voice Assistant

VEHICLE

Selecting the language

Select "Language" to change the

language.

Press the desired language.

Press the back arrow to return to the

previous page.

Slide the slider to increase/decrease

the brightness or switch off the

Ambient lighting (where provided).

AUDIO

It is possible to configure:

Sound settings:

Ambiance sound

Setting the date and time

Select "Date and Time" to modify

the date and time. "Automatic Date

and Time" is activated by default, so

that the setting is made automatically

according to your geolocation.

To adjust manually, deactivate

"Automatic Date and Time".

Press the "Select Time Zone" field

then define a time zone.

Equaliser: increase/decrease

Treble, Mid and Bass acoustic

level

Balance: change the sound

balance right/left/front/back by

sliding the central dot

It is possible to configure:

Vehicle lighting:

Welcome light at the door

opening: enabling/disabling and

duration

Cornering light

enabling/disabling

Reset: reset audio settings to

factory settings

311

Automatic Main Beam enabling/

disabling

Vehicle access:

PERSONALISATION

Door unlock only on driver side:

enabling/disabling

Boot opening on doors unlock:

enabling/disabling

Safety settings:

Rear wiper in reverse gear:

enabling/disabling

388

F6S0164

Diagnostic: starts a diagnostic

process to shows the vehicle

status (i.e. presence of faults)

Tyre Pressure Setup: shows

for each tyre if it’s inflated at the

correct pressure

389

F6S0165

The ADAS available are (depending on

the vehicle):

Attention Alert

Lane Keeping Assist

Advance Lane Keep Assist

Traffic Sign Recognition

Close Obstacles Detection

Advanced Parking Assist

Blind Spot Alert

Press and hold the screen for at least

3 seconds from one of the system's

home pages or press the

application.

In the list, select the "Customisation"

tab

Press the "Displays" field. A page

divided into 2 parts is displayed

fig. 389.

Press the "HOME" button at any time

to leave this page.

PERSONALISING THE SCREEN

"Settings"

Volume of navigation

information (where provided)

UPDATES

It is possible to allow automatic Over

The Air updates and start an update

already downloaded but not installed

(refer to "Software updates" section).

Automatic Braking System

i

Selecting

on a service will bring up

a page with a brief description of it.

Selecting the shortcut to the related

settings is added in the “Quick buttons”

section

ADVANCED DRIVER

ASSISTANCE SYSTEMS

(ADAS)

Press the pencil icon

in the

"Customise Touchscreen" part.

A representation of the organisation

of the different home page (HOME)

Widgets is displayed.

The Advanced Driver Assistance

Systems (ADAS) groups different

driving aid systems that play an

important role in safety. On the screen

fig. 388 you can scroll through the

drop-down menu in “Functions”

section to activate/deactivate ADAS.

NOTE A Widget is a reduced window

of an application or a service.

312

press one of the "+" buttons on the

screen.

Select the desired Widget.

Press the back arrow to return to the

previous page and confirm pressing

"SAVE".

ADDING A WIDGET

(see (3) fig. 335) when changing profile

and at the end of each profile creation.

"Sharing Data and Location":

this mode allows the vehicle to

externally transmit all the personal

data needed for each valid available

connected service

To add a Widget, press

"Add

Widget" on the left of the screen or

press one of the "+" buttons on the

screen.

Select the desired Widget.

Press the back arrow

DELETING A WIDGET

To move a Widget to the bin, press and

to return to

the previous page and confirm pressing

"SAVE".

NOTE The personal data required to

use the connected services is sent to

the providers of these services.

"Sharing Data": this mode

allows the vehicle to externally transmit

all the data needed for each valid

available connected service, with the

exception of vehicle location data (e.g.

GPS coordinates).

hold it, then drag it to the bin

.

ORGANISING THE WIDGETS ON A

HOME PAGE (HOME)

To move a Widget, press and hold it,

then drag it to the desired location.

ADDING A PAGE

To add a page, press

the left of the screen.

Press the back arrow

the previous page.

DELETING A WIDGET

To move a Widget to the bin, press and

PRIVACY SETTINGS

The "Privacy Settings" management

is associated with each profile. This

function is used with a "Guest" profile

configured by default in "Private Mode"

or a profile to be created in the system,

with or without connection with a

mobile device.

"Page" on

to return to

NOTE Some connected services may

not function without the vehicle location

data.

For each profile (even "Guest"), the

last privacy mode saved value will be

restored.

NOTE This mode will not be applied

to the emergency call function or to

specific services to which the user

has consented under the terms of

commercial contracts (e.g. Connected

alarm).

hold it, then drag it to the bin

PERSONALISING THE

INSTRUMENT PANEL

.

During the Profile creation, if there is

no connection with a mobile device,

the mode value will be set to"Private

Mode".

Press the pencil icon

in the

"Customise Driver Information" section.

The modification of the organisation of

the different Widget is displayed on the

instrument panel in real time.

NOTE Depending of the conditions of

the vehicle, it may occur that in some

specific cases the privacy settings

previously linked to a profile could not

be loaded. Please always check the

"geolocation and data transfer status"

icon screened in the upper banner of

the Uconnect™ 10.25"/10.25" NAV

"Private Mode": this mode

does not allow the vehicle to transmit

personal data outside the vehicle.

NOTE Connected services will only

perform local processing inside the

vehicle with limited functions.

NOTE A Widget is a reduced window

of an application or a service.

ADDING A WIDGET

NOTE This mode will not be applied

to the emergency call function or to

specific services with given user's

To add a Widget, press "Add

Widget" on the left of the screen or

313

consent on business contracts

once the country is selected. Slide a

finger on the touch screen from top to

bottom to display all the notifications.

The selection of a country is

necessary to use the available internet

applications.

CONNECTED

SERVICES -

UCONNECT

SERVICES

(Connected alarm). When the vehicle

is in professional use or in use under

specific contracts subscribed (connect

fleet, public delegation…), some

privacy modes won't be available to

the user depending on services data

sharing needs.

(where provided)

Press the "Settings" application.

In the list, select the "Connected

Services" tab.

356)

Uconnect Services connected services

enrich the experience of use of the car

by connecting it to the network.

The services (where provided) allow

you to receive timely assistance in

case of need and emergency, to obtain

information about the status of your

car, its location, control it remotely and

to improve the navigation experience

(where provided) thanks to real-time

updates

NOTE Professional purposes If

the vehicle is used for professional

purposes or under the terms of

specific contracts (e.g. corporate fleet,

government assignment), some privacy

modes will not be available for the user

on the screen, depending on the data

sharing needs of the services.

Choose the country.

The first time you use it, via a

connected mobile device, the system

links to your profile. The connected

mobile device serves as an access key

to saved personal information.

First activate the mobile device’s

Bluetooth® function.

To change the mode, swipe down from

the upper edge of the touch screen, to

display all the quick settings.

Select the desired application,

authentication will be requested if

necessary. This authentication will be

saved for future uses via the mobile

device connected to the current profile.

An authentication will be requested at

each use if the mobile device is not

connected to the current profile or if the

Guest profile is used

You can access the Uconnect Services

through the dedicated FIAT® app

for smartphones or smartwatches,

a web portal, or the Uconnect™

10.25"/10.25" NAV system of your car.

The availability of services requires a

Uconnect Services contract.

Press the button

and select the

chosen mode. The mode is highlighted.

Or,

Press the "Settings" application.

In the list, select the "Connectivity"

tab.

Select "Privacy Settings".

Choose the mode

INTERNET PORTAL

During the first use, upon acquisition of

the vehicle, the user is invited to select

the country of residence for the use of

the Internet portal. If the country is not

selected, the notification is stored in

the notification centre and disappears

Read more about the Uconnect

Services – applicability, availability,

compatibility, packages and

specifications – on the Fiat website.

GENERAL DISCLAIMER

Personal data & privacy

With the use of the "Guest" profile,

an identification will be requested for

each use.

The Manufacturer collects,

processes and uses the personal data

of the car in accordance with legal

314

requirements. Read more about the

general conditions of service and data

protection policies on the Fiat official

website.

When using the services, customers

shall keep their passwords secret for

strictly personal use and not to disclose

them to third parties.

"eCall (SOS)" and "Assistance

call" (see "In an emergency"

section): Customer Care and

Roadside Assistance.

The Customer is solely responsible

for using the services in the car, even

if by other people, and shall inform all

users and occupants of the car about

the services and the functions and

limits of the system.

"Vehicle Health Report":

SERVICES

information on the status and

condition of the car, notifying

potential maintenance needs

to the customer via periodic

e-mails. This service is provided

on condition that the Customer

has previously provided the

Stellantis network with a valid

e-mail address.

WARNING Some of the services listed

below may not be available if the car

is left with the motor off for more than

20 days. Start the motor to reactivate

these services.

Operating prerequisites

To use some of the Uconnect

NOTE The date and time shown on the

Uconnect™ 10.25"/10.25" NAV

system display must match the actual

date and time, even after disconnecting

the battery. Adjust it from the

"Settings" menu of the Uconnect™

10.25"/10.25" NAV system. Any

discrepancy between the date and time

on the display and the actual date and

time may be due to a malfunction in the

Connected Services.

Services, you need to register on

the dedicated portal which can be

accessed from the official Fiat website,

and activate and login to your devices.

Uconnect Services are not available

in all markets and is subject to

limitations depending on Uconnect™

10.25"/10.25" NAV system type,

location and duration of the services.

The full operation of the Uconnect

Services, including the Assistance

call, is subject to mobile network and

GPS geolocation coverage, without

which the proper provision of services

is not guaranteed. Coverage may not

be guaranteed in places such as

tunnels, garages, multistorey car parks,

mountains.

My eCharge (Electric versions):

is a service that allows you to find,

use and pay for charging at public

charging stations and keep track of

your charging history via FIAT® app.

The service also allows you to manage

recharges with your private wallbox

charging station directly from your

smartphone.

According on the equipment of the car

and of the country, different services

may be available for different durations.

For further information about your car,

go to the personal page on the official

Fiat website.

My Car:vehicle status monitoring

service:

"Vehicle Information": informs

the customer on real-time vehicle

status related to fuel level, battery

level, odometer, etc. Logging in

the FIAT® app and Web Portal,

it's possible see the Vehicle

Information updated at the last

time the engine was switched

off. Moreover, when a fault is

Some of the packages made available

to the customer are:

In case of mobile network overload

or problems related to the power

supply of the car (e.g. low battery), the

services may not be available.

My Assistant:Customer care and

safety alert service, which includes:

315

detected, a specific warning

lamp/ alert is sent through push

notification on FIAT® app and

smartwatch.

"In-Vehicle Alerts": possibility

to receive messages and/ or

notifications related to the

provision of services and

reminder messages about the

execution of service and/or recall

campaigns on Uconnect™

10.25"/10.25" NAV system

display. You can contact the

Manufacturer Customer Service

for further information regarding

the messages received.

programming functions are compatible

with those of the car itself, as otherwise

charging might not take place.

"At-Home Digital Assistant": it allows

voice assistant systems to be to use

as additional touchpoint to perform

available Uconnect™ 10.25"/10.25"

NAV features enhancing the

Navigation includes: "POI Search":

it allows customers with Navigation

systems to find the latest database for

local businesses, Points Of Interest and

much more, using the most up-to-date

information. POI search is also available

on FIAT® app by leveraging Google's

maps and Points Of Interest. The full

details (telephone number and address)

as well as the email address/website

of the place can also be shown. "Live

weather, speedcams and traffic": real-

time traffic flow, incidents, road closure

information is provided with graphical

representation. Speed camera location

is provided based on the customer's

location, as well as local weather

information including severe weather

alerts delivered within the navigation

systems. Live traffic, weather and

speed camera are available on the

Uconnect™ 10.25"/10.25" NAV.

"Parking Finder": displays a real-time

indicator of available parking spots

and rates (availability depending

ownership and the connected services

experience. A voice activated digital

assistant allows the user to perform

vehicle remote operations, access

vehicle info, search for POI and much

more. At-Home Digital Assistant

requires connectivity and active

connected services subscription for full

functionality (remote operations/ status/

etc).

"Vehicle Finder": it allows the user to

visualize on smartphone, smartwatch

and website, the vehicle position and

shows the distance between user

position (device's position) and vehicle

position. In addition the user may also

launch a pedestrian navigation on

Google Maps / Apple Maps from user

position to vehicle one. From Vehicle

Finder function the customer is able to

launch Remote Light, to find the vehicle

in case of crowded parking or low

visibility.

My Remote: this can be used to

manage remote operations (switching

on lights, door lock/unlock, find

vehicle, etc.) from the FIAT® app or

smartwatch. My Remote includes:

"E-Control" services: they allow to

manage, remotely, all the functions

related to the of the high-voltage

battery charging, such as immediate

charging, charging programming and

climate schedule. When a high-voltage

battery charge session is planned

using the Uconnect™ 10.25"/10.25"

NAV system display of the car, via

the FIAT® app or smartwatch, and

charging is taking place using devices/

charging points which have their own

planning solutions, make sure that the

on Country). The address of the

parking and the itinerary to reach the

destination can be displayed.

"Fuel Finder" (Hybrid versions):

shows the stations located near the

route directly on the Uconnect™

10.25"/10.25" NAV system. The fuel

prices are also shown (availability

depending on the Country). It's

My Navigation: connected

navigation service (subject to availability

according to version/market). My

316

possible to display the details of the

service station and the route to reach

the destination.

"Charging station Finder" (Electric

versions): display a real-time indicator

of available public charging station

located near the route.

Can be displayed the address, the

itinerary to reach the destination and

additional information directly on the

Uconnect™ 10.25"/10.25" NAV

system

"Map update Over The Air": the

navigation system will recognize the

home area of the user and will keep the

local map updated automatically, with

no need for customer input. When on a

trip outside the user’s home location,

the Uconnect™ 10.25"/10.25" NAV

will update the passing and destination

regions automatically. Maps are

updated up to once per month.

"On Street Parking": helps customers

to find a parking place "on the street"

(not a payment parking, which is

covered by the Parking Finder feature).

When searching an address or POI,

it indicates on the Uconnect™

10.25"/10.25" NAV a level of

the steering wheel and your eyes from

road. Functions that can be managed

are, for instance: the choice of own

profile, airconditioning settings, radio,

telephone, etc. This Service allows

the customer to use a language that

is more natural and easy. To activate

the Natural Speech Voice Recognition

WARNING The icon at the top of the

Uconnect™ 10.25" NAV display

indicates that the geolocation function

is active (ON). When geolocation is on,

the car position is tracked to enable

the functions that require it. When

geolocation is off, the car position

is only tracked by the navigation,

safety, insurance and driver assistance

systems (where provided). See the

Uconnect™ 10.25" NAV system

"Settings" chapter to deactivate the

function.

press the button

wheel.

on the steering

My Fleet Manager (where

provided): allows business customers

to manage company fleets with

maximum efficiency and safety. The

data from the vehicles are collected

and shown via the dedicated web

portal for fleet management to improve

efficiency, reduce costs, prevent risks

and guarantee the safety both for

vehicles and drivers.

DEACTIVATION OF GEOLOCATION

MODE

(only for Uconnect™ 10.25" NAV)

If you wish to deactivate geolocation

mode, simply do so from the

WARNING If the "default settings

are restored", turn off the engine

(ignition device to STOP) and wait a

few minutes before restarting it (ignition

device to ENGINE). The incorrect

performance of the operation and the

short period of time passed between

turning off the engine and turning

it back on may cause the Privacy

settings to not be maintained. In this

case, repeat the operation, extending

the wait time between turning off the

engine and turning it back on.

Uconnect™ 10.25" NAV system

(see the "Settings" menu of the

Uconnect™ 10.25" NAV system for

more details).

UPDATING THE SYSTEM

Uconnect Services and the

Uconnect™ 10.25" NAV system

application software are updated

remotely in order to provide the

customer with newer software

probability of success to find a free

parking slot.

"Natural Speech Voice Recognition":

lets you control various functions inside

your car without leaving your hands off

When geolocation mode is deactivated

some of the services on mobile apps

and web that use the location of the

car will not be available.

317

versions that include new features or

enhancements/enrichments of features

already offered.

DEACTIVATING

RECORDING EVENT

DATA

UCONNECT SERVICES

If you sell your car on which the

Uconnect Services are still active, you

will be responsible for logging off your

profile from the services on the page on

the official Fiat website, by contacting

the Customer Care or by going to a

Fiat Dealership

Electronic control units are installed

in your vehicle. These control units

process data received from the

vehicle's sensors, for example, or data

they generate themselves or exchange

with each other.

Updates are made at the

Manufacturer's discretion.

The availability of updates can be

checked via Settings>Updates,fig. 390

Some of these control units are

required for the correct operation of

your vehicle, some others assist you

while driving (driving or manoeuvring

aids), while others provide comfort or

infotainment functions.

You will also be responsible for

informing the new owner of any

services which have not yet expired

associated with a new Uconnect

Services account.

The following contains general

information about how data is

IMPORTANT

390

F6S0166

processed within the vehicle. You will

find additional information about the

specific data which is downloaded,

stored and transmitted to third

parties and what it is used for in your

vehicle under the keyword "Data

protection". This information is directly

associated with the references for the

functions in question contained in the

corresponding vehicle handbook, or in

the general terms and conditions of

sale.

356) Always follow the highway code

of the country in which you are driving,

and concentrate on the road. Always

drive safely with your hands on the

steering wheel. Only use the Uconnect™

10.25"/10.25" NAV system functions

when you are sure that it is safe to do

so. The customer is liable for all risks

associated with using the functions and

applications of the car. Failure to follow

these rules may cause serious accidents

and/or death.

Some system updates will be

managed automatically, others will be

communicated to the Customer by

showing messages on the display of

the Uconnect™ 10.25" NAV, allowing

the customer to confirm or postpone

the update itself.

The customer will be notified by the U

connect™ 10.25" NAV system if the

system is unavailable.

To read more about services, features,

specifications, availability and any

updates please always refer to the

content included in the official Fiat

website.

This information is also available online.

VEHICLE OPERATING DATA

The control units process the data

used for the operation of the vehicle.

This data includes, for example:

318

Information about the state of the

vehicle (e.g. speed, travel time, lateral

acceleration, wheel rotation rate,

fastened seat belts display).

Environmental conditions (e.g.

temperature, rain sensor, distance

sensor).

For Electric vehicles, the traction

battery charge level and the estimated

driving range.

The Manufacturer's liability may also

be engaged. The Manufacturer may

also use the operating data taken from

the vehicle for product recalls. This

data may also be used to check the

customer's warranty and any claims

made under warranty.

In particular circumstances (e.g. if the

vehicle has detected a malfunction), it

may be necessary to record data which

would otherwise simply not be stored.

When taking your vehicle in for

servicing (e.g. repairs, maintenance),

the stored operating data may be read

along with the vehicle's identification

number and used if necessary.

The personnel working for the

As a general rule, this data is

Any malfunctions stored in the vehicle

may be reset by an after-sales service

company during servicing or repair

work, or at your request.

COMFORT AND INFOTAINMENT

FUNCTIONS

Comfort settings and personalised

settings may be saved in the vehicle

and modified or reinitialised at any time.

Depending on the vehicle's equipment

level, this may include:

temporary, is not stored for longer than

one operating cycle and is only used

within the vehicle itself. The control

units often record this data (including

the vehicle's key). This function allows

either the temporary or permanent

storage of information about the

state of the vehicle, stresses on

components, servicing requirements,

as well as events and technical errors.

Depending on the vehicle's equipment

level, the data stored is as follows:

Operating state of system

components (e.g. filling level, tyre

pressures, battery charge status).

Faults and malfunctions in important

system components (e.g. lamps,

brakes).

System reactions in specific driving

situations (e.g. deployment of an

airbag, triggering of stability control and

braking systems).

servicing network (e.g. garages,

manufacturers) or third parties (e.g.

roadside assistance agents) may read

the vehicle's data.

This also applies to work carried out

under warranty and quality assurance

measures.

Seat and steering wheel position

settings.

Chassis and air conditioning settings.

Personalised settings such as the

interior lighting.

You can enter your own data into

the functions of your vehicle's audio

and telematic system, as part of the

selected functionalities.

This data is generally read via the

OBD (On-Board Diagnostics) port

fitted by law to the vehicle. It is used

to report on the technical state of

the vehicle or its components and

facilitates the diagnosis of malfunctions,

in compliance with warranty obligations

and for quality improvement. This

data, in particular the information

relating to stress on components,

technical events, operator errors and

other malfunctions, is sent to the

Manufacturer, if necessary, along with

the vehicle's identification number.

Depending on the vehicle's equipment

level, this may include:

Multimedia data such as music,

videos or photos to be read by an

integrated multimedia system.

Information about events which have

damaged the vehicle.

319

and other general information about the

vehicle. For more information, please

refer to the user instructions for the

vehicle or the audio and telematics

system.

Address book data to be used with

an integrated hands-free system or

with an integrated navigation system.

Entered destinations

Data regarding the use of online

services.

This data for the comfort and

infotainment functions may be stored

locally in the vehicle or saved to a

device that you have connected to the

vehicle (e.g. smartphone, USB memory

stick or MP3 player). Data that you

have entered yourself may be deleted

at any time.

EXCLUSIVE SERVICES

As regards the Manufacturer's online

services, the corresponding functions

are described by the Manufacturer

in an appropriate medium (e.g.

handbook, Manufacturer's website)

and the information about data

protection is provided.

Integrating a smartphone allows

you to use its applications, such as

a navigation app or music player.

No other integration between the

smartphone and the vehicle is possible,

in particular active access to vehicle

data. How the data is processed

subsequently is determined by the

supplier of the application being used.

The ability to change settings depends

on the application in question and on

the operating system installed on your

smartphone.

Personal data may be used for online

services.

The exchange of data for this purpose

takes place over a secure connection,

using for example the Manufacturer's

dedicated computer systems. The

collection, processing and use of

personal data for the development

of services are carried out solely on

the basis of a legal authorisation,

for example in the case of a legal

emergency call system or a contractual

agreement or else under a consent

agreement.

This data may also be transmitted

outside the vehicle at your request,

particularly when using online services

in line with the settings that you have

selected.

SMARTPHONE INTEGRATION (E.G.

ANDROID AUTO® OR APPLE

CARPLAY

If your vehicle is equipped accordingly,

you can connect your smartphone or

another mobile device to the vehicle in

order to operate it using the vehicle's

integrated controls. Images and

sounds from the smartphone can be

transmitted through the audio and

telematics system.

ONLINE SERVICES

If your vehicle is connected to a

wireless network, data can be

exchanged between your vehicle and

other systems.

You can activate or deactivate the

services and functions (some may

be chargeable) and, in some cases,

the vehicle's entire connection to the

wireless network. This does not include

the statutory functions and services

such as the emergency or assistance

call system.

Connection to a wireless network is

made possible via a transmitter located

in your vehicle or a mobile device that

you have provided (e.g. smartphone).

The online services can be used via

this wireless connection. These include

online services and applications (apps)

provided to you by the Manufacturer or

other suppliers.

Specific information is simultaneously

sent to your smartphone. Depending

on the type of integration, this includes

data such as location, day/night mode

THIRD-PARTY SERVICES

If you use online services provided

by other (third-party) suppliers,

these services are subject to the

320

responsibility, the data protection and

the terms and conditions of use of the

supplier in question. The Manufacturer

often has no influence over the content

exchanged in this regard.

mobile network. Large updates are

downloaded only via the Wi-Fi network.

The availability of an update is notified

on the Info Display at the end of a trip

with an option of immediate installation

or postponement of installation.

For this, a secure radio network

connection between the vehicle and

the device management server will be

established when ignition is switched

on and a mobile network is available.

Depending on the equipment of the

vehicle, connection configuration must

be set to "Connected vehicle" to allow

the establishment of the radio network

connection.

Please therefore ensure that you

are aware of the nature, extent and

purpose of the collection and use of

personal data as part of the third

party services provided by the service

provider in question.

The installation time is variable and can

take several minutes with a maximum

of about 30 minutes. A notification will

give an estimate of the duration and a

description of the update.

Irrespective of a valid connected

service subscription, remote product

security or product safety related

device management and software and

firmware updates will be performed

when the processing is necessary for

the compliance with a legal obligation

to which the manufacturer is subject

(e.g. applicable product liability

law, emergency call regulation) or

when the processing is necessary

in order to protect the vital interests

of the respective vehicle users and

passengers.

Update information is available through

the "Settings" application.

SOFTWARE UPDATE

The Infotainment system can download

and install selected software updates

over a wireless connection.

press the

"Settings" application

in the list, select the "Updates" tab

press the button . It allows you to

change the authorisation for automatic

downloading of updates via an external

Wi-Fi network.

NOTE The availability of these over the

air vehicle software updates varies

by vehicle and country. Find more

information on our website.

REMOTE DEVICE MANAGEMENT

AND REMOTE SOFTWARE AND

FIRMWARE UPDATES

As an integral part of the service related

to the performance of subscribed

connected service contracts,

necessary device management and

necessary software and firmware

updates related to the software and

firmware for the named connected

service will be performed remotely,

in particular by using over the air

technology.

357)

162)

NOTE Steps for downloading and

installing updates may vary by vehicle.

For safety reasons and because it

requires sustained attention by the

driver, the installation must be carried

out with the ignition on without starting

the engine. The installation cannot be

carried out in the following cases:

engine running

The establishment of a secure radio

network connection and the related

remote updates are not affected by

privacy settings and will be performed

in principal after an initiation by the

vehicle user following a respective

notification.

emergency call in progress

insufficient vehicle battery charge

The system is able to notify receipt of

an update as soon as it is connected

to an exterior Wi-Fi network or a

321

charging the vehicle's high voltage

battery

Velcro Companies

Velcro® is a registered trademark of

Velcro Companies.

REGISTERED

TRADEMARKS

NOTE During the installation process,

the vehicle may not be operational.

If the update has failed, seek the

assistance of a Fiat Dealership.

Apple Inc.

Apple CarPlay is a trademark of Apple

Inc.

RADIO FREQUENCY

IDENTIFICATION

(RFID)

App Store and iTunes Store are

trademarks of Apple Inc.

NOTE The use of this service is not

charged by the Contractor. On the

other hand, the use of the WI-FI and/

or cellular networks of your smartphone

can generate additional fees if your

data plan is exceeded. These possible

costs are reflected in the bill of your

telephone operator.

RFID technology is used in some

vehicles for functions such as tyre

pressure monitoring and immobiliser.

It is also used in connection with

conveniences such as radio remote

controls for door locking / unlocking

and starting. RFID technology in Fiat

vehicles does not use or record

personal information or link with any

other Fiat system containing personal

information.

iPhone, iPod, iPod touch, iPod nano,

iPad and Siri are trademarks of Apple

Inc.

All the other trademarks belong to their

respective owners.

Use of the Made for Apple badge

means that an accessory has been

designed to connect specifically to

the Apple product(s) identified in the

badge and has been certified by the

developer to meet Apple performance

standards. Apple is not responsible

for the operation of this device or its

compliance with safety and regulatory

standards.

IMPORTANT

357) For safety reasons and because it

requires sustained attention by the driver,

the installation must be carried out with

the ignition on without starting the engine.

The installation cannot be carried out

in the following cases: engine running,

emergency call in progress, insufficient

conventional battery level, when charging

high-voltage battery (electric vehicles).

Bluetooth SIG, Inc.

Bluetooth® is a registered trademark of

Bluetooth SIG, Inc.

DivX, LLC

DivX® and DivX Certified® are

registered trademarks of DivX, LLC.

Google Inc.

Android™ and Google Play™ Store are

trademarks of Google LLC.

WARNING

162) After a software update, wait for

about 20 minutes before restarting the

engine to allow the update to complete.

322

OFFICIAL TYPE

APPROVALS

All radio equipment provided with

the car complies with Directive

2014/53/EU, UA.RED.TR, the French

SAR Decree Law of 15/11/2019 and

the UKCA (UK Conformity Assessed)

Certification in force in the United

Kingdom.

For further information visit the

websites

For more information about

certifications and open

source lists available for in-car

components use the following link:

Radio frequency

devices

All radio frequency devices comply with

the regulations in force in the countries

in which they are sold.

For further information visit the

websites

323

Multimedia for Your Fiat 600 SUV Second Generation (2023-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals