Get Parking Aids Guide for Ford Edge SUV Second Generation (2015-2023)

PRINCIPLE OF OPERATION

WARNINGS

To help avoid personal injury, always

use caution when in reverse (R) and

when using the sensing system.

The system may not detect objects

with surfaces that absorb reflection.

Always drive with due care and

attention. Failure to take care may result

in a crash.

Traffic control systems, inclement

weather, air brakes, external motors

and fans may affect the correct

operation of the sensing system.This may

cause reduced performance or false alerts.

The system may not detect small or

moving objects, particularly those

close to the ground.

Note: If your vehicle is equipped with

MyKey™, the sensing system cannot be

turned off when a MyKey™ is present. See

Principle of Operation (page 57).

Note: Keep the sensors, located on the

bumper or fascia, free from snow, ice and

large accumulations of dirt. If the sensors

are covered, the system’s accuracy can be

affected. Do not clean the sensors with

sharp objects.

Note: If your vehicle sustains damage to

the bumper or fascia, leaving it misaligned

or bent, the sensing zone may be altered

causing inaccurate measurement of

obstacles or false alerts.

Note: Certain add-on devices installed

around the bumper or fascia may create

false alerts. For example, large trailer

hitches, bike or surfboard racks, license plate

brackets, bumper covers or any other device

that may block the normal detection zone

of the system. Remove the add-on device

to prevent false alerts.

Note: When a trailer is connected to your

vehicle, the rear parking aid may detect the

trailer and therefore provide an alert. Disable

the rear parking aid when a trailer is

connected to prevent the alert.

The sensing system warns the driver of

obstacles within a certain range of your

vehicle. The system turns on automatically

whenever you switch the ignition on.

The system can be switched off through

the information display menu or from the

pop-up message that appears once you

shift the transmission into reverse (R). See

General Information (page 102).

If a fault is present in the system, a warning

message appears in the information

display. See General Information (page

102).

REAR PARKING AID (If Equipped)

The rear sensors are only active when the

transmission is in reverse (R). As your

vehicle moves closer to the obstacle, the

rate of the audible warning increases.

When the obstacle is less than 12 in

(30 cm) away, the warning sounds

continuously. If the system detects a

stationary or receding object farther than

12 in (30 cm) from the corners of the

bumper, the tone sounds for only three

seconds. Once the system detects an

object approaching, the warning sounds

again.

190

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

E130178

Coverage area of up to 6 ft (1.8 m) from

the rear bumper. There may be decreased

coverage area at the outer corners of the

bumper.

The system detects certain objects while

the transmission is in reverse (R) :

• Your vehicle is moving toward a

stationary object at a speed of 3 mph

(5 km/h) or less.

• Your vehicle is not moving, but a

moving object is approaching the rear

of your vehicle at a speed of 3 mph

(5 km/h) or less.

• Your vehicle is moving at a speed of

less than 3 mph (5 km/h) and a moving

object is approaching the rear of your

vehicle at a speed of less than 3 mph

(5 km/h).

The system provides audio warnings only

when your vehicle is moving or when your

vehicle is stationary and the detected

obstacle is less than 12 in (30 cm) away

from the bumper.

Obstacle Distance Indicator (If

Equipped)

The system provides obstacle distance

indication through the information display.

The distance indicator displays when the

transmission is in reverse (R).

The indicator displays:

• As the distance to the obstacle

decreases the indicator blocks

illuminate and move towards the

vehicle icon.

• If there is no obstacle detected, the

distance indicator blocks are grayed

out.

FRONT PARKING AID (If Equipped)

The front sensors are active when the

transmission is in any position other than

park (P) and your vehicle is traveling at low

speed.

E187330

Coverage area of up to 28 in (70 cm) from

the front bumper. The coverage area

decreases at the outer corners.

When your vehicle approaches an object,

a warning tone sounds. When your vehicle

moves closer to an object, the warning

tone repeat rate increases. The warning

tone sounds continuously when an object

is 12 in (30 cm) or less from the front

bumper.

191

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

You can switch the system off through the

information display menu or from the

pop-up message that appears once you

shift the transmission into reverse (R). See

General Information (page 102). If your

vehicle has a parking aid button, you can

switch the system off by pressing the

button.

Obstacle Distance Indicator (If

Equipped)

The system provides obstacle distance

indication through the information display.

The indicator displays:

• As the distance to the obstacle

decreases the indicator blocks

illuminate and move towards the

vehicle icon.

• If there is no obstacle detected, the

distance indicator blocks are grayed

out.

If the transmission is in reverse (R), the

front sensing system provides audio

warnings when your vehicle is moving and

the detected obstacle is moving towards

your vehicle. Once the vehicle is stationary,

the audio warning will be stopped after 2

seconds. Visual indication is always

present in reverse (R).

If the transmission is in drive (D) or any

other forward gear (for example, low (L),

sport (S) or any forward gear in a manual

transmission), the front sensing system

provides audio and visual warnings when

your vehicle is moving below a speed of

5 mph (8 km/h) and an obstacle is located

inside the detection area. Once the vehicle

is stationary, the audio warning will be

stopped after 2 seconds and the visual

indication stops after 4 seconds. If the

obstacles detected are within 12 in

(30 cm), the visual indication remains on.

If the transmission is in neutral (N), the

system provides visual indication only

when your vehicle is moving at 5 mph

(8 km/h) or below and an obstacle is

located inside the detection area. Once

your vehicle is stationary, the visual

indication will stop after 4 seconds.

SIDE SENSING SYSTEM (If

Equipped)

The side sensing system uses the front and

rear side sensors to detect and map

obstacles within the vehicle's driving path,

located near the sides of your vehicle. The

side sensors are active when the

transmission is in any position other than

park (P).

Note: Obstacles that enter the side

detection area without being detected and

mapped by the front or rear side sensors will

not be detected.

E187810

Coverage area is up to 24 in (60 cm) from

the sides of your vehicle.

When the system detects an object close

to the side of your vehicle, an audible

warning sounds. As your vehicle moves

closer to obstacles within the driving path

of your vehicle, the rate of the audible

warning increases.

192

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

Obstacle Distance Indicator (If

Equipped)

E190459

The system provides obstacle distance

indication through the information display.

As the distance to the obstacle decreases,

the indicator blocks illuminate and move

toward the vehicle icon. If there is no

obstacle detected, the distance indicator

blocks show greyed out.

When you shift to reverse (R), the side

sensing system provides audible warnings

when your vehicle is moving and obstacles

are detected within 24 in (60 cm) and are

inside the driving path of your vehicle.

When you stop your vehicle the audible

warning stops after two seconds.

Note: Visual distance indication remains

on when the transmission is in reverse (R).

When you shift to drive (D) or any other

forward gear, for example, low (L), sport

(S) or any forward gear in manual

transmission, the side sensing system

provides audible and visual distance

warnings when your vehicle is moving

below a speed of 5 mph (8 km/h) and

obstacles are detected within 24 in

(60 cm) and are inside the driving path of

your vehicle. Once your vehicle reaches a

standstill condition, the audible warning

stops after two seconds and visual

indication stops after four seconds.

If the transmission is in neutral (N), the side

sensing system provides visual distance

indication only when your vehicle is moving

below a speed of 5 mph (8 km/h) and

there is a front or rear parking aid obstacle

detected, and the side obstacle is within

24 in (60 cm) from the side of your vehicle.

When you stop your vehicle the visual

distance indication stops after four

seconds.

If the side sensing system is not available,

the side distance indicator blocks do not

appear.

The side sensing system is not available

under the following condition:

• If you switch the traction control

system off.

The side sensing system may not be

available until you have driven

approximately the length of your vehicle

in order for the system to reinitialize if:

• You switch the ignition on, off and back

on.

• Your vehicle remains stationary for over

two minutes.

• The anti-lock brake system is

activated.

• The traction control system is

activated.

• When the steering wheel angle

information is not available, the side

sensing system is not available. The

vehicle must be driven at least 492 ft

(150 m) above 19 mph (30 km/h) to

recover the steering wheel angle

information.

193

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

ACTIVE PARK ASSIST (If Equipped)

Parallel Parking, Perpendicular

Parking, Parallel Park Out Assist

WARNINGS

You must remain in your vehicle

when the system turns on. At all

times, you are responsible for

controlling your vehicle, supervising the

system and intervening, if required. Failure

to take care may result in the loss of

control of your vehicle, serious personal

injury or death.

The sensors may not detect objects

in heavy rain or other conditions that

cause interference.

Active park assist does not apply the

brakes under any circumstances.

The system is designed to aid the

driver. It is not intended to replace

your attention and judgment. You are

still responsible to drive with due care and

attention.

Note: The Blind Spot Information System

does not detect traffic alongside or behind

your vehicle during an Active Park Assist

maneuver.

The system detects an available parallel

or perpendicular parking space and

automatically steers your vehicle into the

space (hands-free) while you control the

accelerator, gearshift and brakes. The

system visually and audibly guides you to

park your vehicle.

If you are uncomfortable with the proximity

to any vehicle or object, you may choose

to override the system by grabbing the

steering wheel or by pressing the button.

Parallel Park Out Assist automatically

steers your vehicle out of a parallel parking

space (hands-free) while you control the

accelerator, gearshift and brakes. The

system visually and audibly guides you to

enter traffic.

The system may not correctly operate in

any of the following conditions:

• You use a spare tire or a tire

significantly worn more than the other

tires.

• One or more tires are improperly

inflated.

• You try to park on a tight curve.

• Something passes between the front

bumper and the parking space. For

example, a pedestrian or cyclist.

• The edge of the neighboring parked

vehicle is high off the ground. For

example, a bus, tow truck or flatbed

truck.

• The weather conditions are poor. For

example, during heavy rain, snow or

fog.

Note: Keep the sensors on the bumper or

fascia free from snow, ice and large

accumulations of dirt. Covered sensors can

affect the system's accuracy. Do not clean

the sensors with sharp objects.

Note: The sensors may not detect objects

with surfaces that absorb ultrasonic waves

or cause ultrasonic interference. For

example, motorcycle exhaust, truck air

brakes or horns.

Note: Following a change in tire size, the

system must recalibrate and operation may

be impaired for a short time.

194

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

Do not use the system if:

• You have attached a foreign object

close to the sensors on the front or rear

of your vehicle. For example, a bike rack

or trailer.

• You attach an overhanging object to

the roof. For example, a surfboard.

• A foreign object damages or obstructs

the front or rear bumper or side

sensors.

• The correct tire size is not in use on your

vehicle. For example, a mini-spare tire.

Using Active Park Assist - Parallel

Parking

E146186

Press the Active Park Assist

button once to search for a

parallel parking space.

When driving at a speed less than 22 mph

(35 km/h), the system automatically scans

both sides of your vehicle for an available

parking space. The system displays a

message and a corresponding graphic to

indicate it is searching for a parking space.

Use the direction indicator to select

searching either to the left-hand side or

right-hand side of your vehicle.

Note: If the direction indicators are not

used, the system defaults to the passenger

side of your vehicle.

E130107

Note: You can also switch the system on

after you have already driven partially or

completely past a parking space. Press the

Active Park Assist button and the system

informs you if you have recently passed a

suitable parking space.

When the system finds a suitable space,

it displays a message and a tone sounds.

Stop your vehicle and follow the

instructions on the screen. If your vehicle

is moving very slowly, you may need to pull

forward a short distance before the system

is ready to park.

Note: You must observe that the space the

system selects remains clear of obstructions

at all times during the maneuver.

Note: Drive your vehicle within 5 ft (1.5 m)

and as parallel as possible to the other

vehicles while passing a parking space.

Note: The system always offers the last

parking space it detects. For example, if your

vehicle detects multiple spaces while you

are driving, it offers the last one.

Note: If driven above approximately 22 mph

(35 km/h), the system shows a message to

alert you to reduce your vehicle speed.

195

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

Automatically Steering into a Parking

Space

Note: If your vehicle speed exceeds

approximately 6 mph (10 km/h) or you

interrupt the maneuver, the system switches

off and you need to take full control of your

vehicle.

When you shift the transmission into

reverse (R), with your hands off the

steering wheel and nothing obstructing its

movement, your vehicle steers itself into

the space (hands-free). The system

displays instructions to move your vehicle

backward and forward in the space.

E130108

When you believe your vehicle is properly

parked, or you hear a solid tone

accompanied by a display message, bring

your vehicle to a complete stop.

When the Active Park Assist maneuver is

complete, the system displays a message

and a tone sounds.

Note: You are responsible for checking your

parked vehicle and making any necessary

corrections before leaving your vehicle.

Using Active Park Assist -

Perpendicular Parking

E146186

Press the Active Park Assist

button twice to search for a

perpendicular parking space.

When driving at a speed less than 19 mph

(30 km/h), the system displays a message

and a corresponding graphic to indicate it

is searching for a parking space. Use the

direction indicator to select searching

either to the left-hand side or right-hand

side of your vehicle.

Note: If you do not make a selection, the

system defaults to the passenger side.

E186193

196

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

When the system finds a suitable space,

it displays a message and a tone sounds.

Stop your vehicle and follow the

instructions on the screen. If your vehicle

is moving very slowly, you may need to pull

forward a short distance before the system

is ready to park.

Note: You must observe that the space the

system selects remains clear of obstructions

at all times during the maneuver.

Note: You should drive your vehicle within

5 ft (1.5 m) and as perpendicular as possible

to the other vehicles while passing a parking

space.

Note: The system always offers the last

detected parking space. For example, if your

vehicle detects multiple spaces while you

are driving, it offers the last one.

Note: If driven above approximately 19 mph

(30 km/h), the system shows a message to

alert you to reduce your vehicle speed.

Automatically Steering into a Parking

Space

Note: If your vehicle speed exceeds

approximately 6 mph (10 km/h) or you

interrupt the maneuver, the system switches

off and you need to take full control of your

vehicle.

E186191

When you shift the transmission into

reverse (R), with your hands off the wheel

and nothing obstructing its movement,

your vehicle steers itself into the space.

The system displays instructions to move

your vehicle backward and forward in the

space.

When you believe your vehicle is properly

parked, or you hear a solid tone

accompanied by a display message, bring

your vehicle to a complete stop.

When the Active Park Assist maneuver is

complete, the system displays a message

and a tone sounds.

Note: You are responsible for checking your

parked vehicle and making any necessary

corrections before leaving your vehicle.

Using Active Park Assist - Parallel Park

Out Assist

E146186

Press the Active Park Assist

button once while your vehicle

is at rest in a parallel parking

space to use Parallel Park Out Assist.

The system displays a message instructing

you to select a side. Use the direction

indicator to select which side of your

vehicle you want to exit the parking space.

197

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

E188012

The system determines the clearance to

the front and rear of your vehicle and

automatically steers your vehicle out of a

parallel parking space (hands-free) while

you control the accelerator, gearshift and

brakes. The system visually and audibly

guides you to enter traffic.

After the system directs your vehicle past

the adjacent vehicle or object, it guides you

to take control of the steering to complete

the exit out of the parking space.

Note: If the clearance in front of your

vehicle allows easy departure, the Parallel

Park Out Assist feature may not be

available.

Note: You are responsible for controlling

your vehicle and making sure the path is

clear prior to pulling into traffic.

Note: Do not use this system to assist in

exiting perpendicular parking spaces.

Damages to your vehicle may occur.

Note: If your vehicle speed exceeds

approximately 3 mph (5 km/h) or you

interrupt the maneuver, the system switches

off and you need to take full control of your

vehicle.

Deactivating the Active Park

Assist Feature

You can manually deactivate the system

by:

• Pressing the Active Park Assist button

during an active maneuver.

• Grabbing the steering wheel during an

active maneuver.

• Driving above approximately 22 mph

(35 km/h) for 30 seconds while

searching for a parking space.

• Driving above approximately 6 mph

(10 km/h) during an active maneuver.

• Switching the traction control system

off.

Certain vehicle conditions may also

deactivate the system, for example:

• The traction control system activates.

• There is an anti-lock brake system

activation or failure.

If a problem occurs with the system, a

warning message displays accompanied

by a tone. Occasional system messages

may occur in normal operation. For

recurring or frequent system faults, contact

an authorized dealer.

198

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

Troubleshooting the System

Possible CauseSymptom

You may have the traction control system switched off.

The system does not look for a

space.

The transmission is in reverse (R). Your vehicle must

be moving forward to be able to detect a parking space.

The sensors may be covered. For example, snow, ice

or dirt buildup. Covered sensors can affect how the

system functions.

The system does not offer a

parking space.

There is not enough room in the parking space for your

vehicle to safely park.

There is not enough space for the parking maneuver on

the opposite side of the parking space.

The parking space is more than 5 ft (1.5 m) or less than

16 in (0.4 m) away.

Your vehicle speed is greater than 22 mph (35 km/h)

for parallel parking, or greater than 19 mph (30 km/h)

for perpendicular parking.

You recently disconnected or replaced the battery. After

a battery disconnect, you must drive your vehicle on a

straight road for a short period of time.

Your vehicle is rolling in the opposite direction of the

current transmission position. For example, rolling

forward when in reverse (R).

The system does not position

the vehicle correctly.

An irregular curb along the parking space prevents the

system from aligning your vehicle properly.

Improperly parked vehicles or objects are boarding the

space.

Your vehicle is too far past the parking space. The

system performs best when you drive the same

distance past the parking space.

You have incorrectly installed or maintained the tires.

For example, not inflated correctly, improper size, or of

different sizes.

A repair or alteration changes the detection capabilities.

199

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

Possible CauseSymptom

A parked vehicle has a high attachment. For example,

a salt sprayer, snowplow or moving truck bed.

The parking space length or position of parked objects

changes after your vehicle passes the space.

The temperature around your vehicle quickly changes.

For example, driving from a heated garage into the cold,

or after leaving a car wash.

REAR VIEW CAMERA

WARNINGS

The rear view camera system is a

reverse aid supplement device that

still requires the driver to use it in

conjunction with the interior and exterior

mirrors for maximum coverage.

Objects that are close to either

corner of the bumper or under the

bumper, might not be seen on the

screen due to the limited coverage of the

camera system.

Reverse your vehicle as slow as

possible, higher speeds may limit

your reaction time to stop your

vehicle.

Use caution when the rear cargo door

is ajar. If the rear cargo door is ajar,

the camera will be out of position

and the video image may be incorrect. All

guidelines disappear when the rear cargo

door is ajar. Some vehicles may not come

equipped with guidelines.

Use caution when turning camera

features on or off when the

transmission is not in park (P). Make

sure your vehicle is not moving.

The rear view camera system provides a

video image of the area behind your

vehicle.

During operation, lines appear in the

display which represent your vehicle’s path

and proximity to objects behind your

vehicle.

E142435

The camera is located on the rear cargo

door.

Using the Rear View Camera

System

The rear view camera system displays

what is behind your vehicle when you place

the transmission in reverse (R).

Note: The reverse sensing system is not

effective at speeds above 3 mph (5 km/h)

and may not detect certain angular or

moving objects.

200

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

The system uses three types of guides to

help you see what is behind your vehicle:

• Active guidelines: Show the intended

path of your vehicle when reversing.

• Fixed guidelines: Show the actual path

your vehicle is moving in while reversing

in a straight line. This can be helpful

when backing into a parking space or

aligning your vehicle with another

object behind you.

• Centerline: Helps align the center of

your vehicle with an object (for

example, a trailer).

Note: If the transmission is in reverse (R)

and the rear cargo door is open, no rear view

camera features will display.

Note: When towing, the camera only sees

what you are towing. This might not provide

adequate coverage as it usually provides in

normal operation and some objects might

not be seen. In some vehicles, the guidelines

may disappear when you connect the trailer

tow connector.

The camera may not operate correctly

under the following conditions:

• Nighttime or dark areas if one or both

reverse lamps are not operating.

• Mud, water or debris obstructs the

camera's view. Clean the lens with a

soft, lint-free cloth and non-abrasive

cleaner.

• The rear of your vehicle is hit or

damaged, causing the camera to

become misaligned.

Camera System Settings

You can access the rear view camera

system settings through the display screen.

See General Information (page 102).

Camera Guidelines

Note: Active guidelines are only available

when the transmission is in reverse (R).

A B C D

E142436

Active guidelinesA

CenterlineB

Fixed guideline: Green zoneC

Fixed guideline: Yellow zoneD

Fixed guideline: Red zoneE

Rear bumperF

Active guidelines are only shown with fixed

guidelines. To use active guidelines, turn

the steering wheel to point the guidelines

toward an intended path. If you change the

steering wheel position while reversing,

your vehicle might deviate from the original

intended path.

201

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

The fixed and active guidelines fade in and

out depending on the steering wheel

position. The active guidelines do not

display when the steering wheel position

is straight.

Always use caution while reversing.

Objects in the red zone are closest to your

vehicle and objects in the green zone are

farther away. Objects are getting closer to

your vehicle as they move from the green

zone to the yellow or red zones. Use the

side view mirrors and rear view mirror to

get better coverage on both sides and rear

of the vehicle.

Obstacle Distance Indicator (If

Equipped)

E190459

The system will provide an image of your

vehicle and the sensor zones. The zones

will highlight green, yellow and red when

the parking aid sensors detect an object in

the coverage area.

Manual Zoom

WARNING

When manual zoom is on, the full

area behind your vehicle may not

show. Be aware of your surroundings

when using the manual zoom feature.

Note: Manual zoom is only available when

the transmission is in reverse (R).

Note: When you enable manual zoom, only

the centerline is shown.

Selectable settings for this feature are

Zoom in (+) and Zoom out (-). Press the

symbol in the camera screen to change the

view. The default setting is Zoom OFF.

This allows you to get a closer view of an

object behind your vehicle. The zoomed

image keeps the bumper in the image to

provide a reference. The zoom is only

active while the transmission is in reverse

(R).

Rear Camera Delay

Selectable settings for this feature are ON

and OFF. The default setting for the rear

camera delay is OFF.

When shifting the transmission out of

reverse (R) and into any gear other than

park (P), the camera image remains in the

display until:

• Your vehicle speed sufficiently

increases.

• You shift your vehicle into park (P)

(automatic transmission).

• You apply the parking brake (manual

transmission).

202

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

180 DEGREE CAMERA (If Equipped)

WARNINGS

The camera system is a supplement

system that still requires the driver

to use it in conjunction with looking

out the windows, and checking the interior

and exterior mirrors for maximum

coverage.

You may not see objects that are

close to either corner of the bumper

or under the bumper due to the

limited coverage of the camera system.

Use caution when turning camera

features ON or OFF while out of park

(P). Make sure your vehicle is not

moving.

E188845

The front view camera is located in the

grille.

The front view camera provides a video

image of the area in front of your vehicle.

Note: The area displayed on the screen may

vary according to your vehicle's orientation

or road condition.

Note: The front view camera will switch off

if your vehicle speed exceeds 6 mph

(10 km/h). You will have to switch the

system back on by using the camera system

button once below the speed threshold.

Note: Additional camera information can

be found in the rear view camera section.

See Rear View Camera (page 200).

Using the 180 degree camera

system

The 180 degree camera system consists

of front and rear cameras. The system:

• Allows you to see what is directly in

front or behind your vehicle.

• Provides cross traffic view in front and

behind your vehicle.

• Provides visibility during parking

maneuvers.

E188847

The camera system button is

located on the audio unit and

allows you to toggle through

different camera views.

Note: The camera system may not operate

correctly if mud, water or debris obstructs

the camera's view. You can clean the lens

with a soft, lint-free cloth and non-abrasive

cleaner or by using your front or rear washer.

See Wipers and Washers (page 81).

Camera Views

Press the camera button to toggle

between different views.

• Normal Front View: Provides an

image of what is directly in front your

vehicle when your vehicle is in neutral

(N) or drive (D).

• Expanded Front View: Provides an

expanded 180 degree image of what

is directly in front your vehicle when

your vehicle is in neutral (N) or drive

(D).

203

Edge (CDQ) Canada/United States of America, enUSA, Edition date: 201706, First Printing

Parking Aids

Parking Aids for Your Ford Edge SUV Second Generation (2015-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals