2024-2026 Ford Edge SUV Exterior Lighting User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Exterior Lighting for Your Ford Edge SUV Third Generation (2024-2026)

EXTERIOR LIGHTING
CONTROL
E322426
Lamps off.A
Parking lamps on.B
Headlamps on.C
Autolamps on.D
Rotate the control to make a selection.
HEADLAMPS
USING THE HIGH BEAM
HEADLAMPS
E339577
E67019
Push the lever away from you to
switch the high beam on.
Push the lever away from you again or pull
the lever toward you to switch the high
beam off.
Slightly pull the lever toward you and
release it to flash the headlamps.
SWITCHING HEADLAMP EXIT
DELAY ON AND OFF
To switch headlamp exit delay on, pull the
turn signal lever toward you after switching
your vehicle off.
To switch headlamp exit delay off, pull the
turn signal lever toward you again or switch
your vehicle on.
Note: The headlamps turn off after three
minutes with any door open or 30 seconds
after the last door closes.
HEADLAMP INDICATORS
Lamps On
E71341
Illuminates when you switch the
low beam headlamps or the
parking lamps on.
Headlamp High Beam
E67019
Illuminates when you switch the
high beam headlamps on.
96
2024 Edge (CDQ) Canada/United States of America, enUSA, Edition date: 202306, DOM
Exterior Lighting
HEADLAMPS –
TROUBLESHOOTING
HEADLAMPS – FREQUENTLY
ASKED QUESTIONS
Why is there condensation in the
headlamps?
• Headlamps have vents to
accommodate normal changes in air
pressure. Condensation can be a
natural by-product of this design.
When moist air enters the lamp
assembly through the vents, there is a
possibility that condensation can occur
when the temperature is cold. When
normal condensation occurs, a fine
mist can form on the interior of the
lens. The fine mist eventually clears
and exits through the vents during
normal operation.
How much condensation is
acceptable?
• The presence of a fine mist, for
example no streaks, drip marks or large
droplets. A fine mist covers less than
50% of the lens.
How long does it take for the
acceptable condensation to clear?
• Clearing time can take as long as 48
hours under dry weather conditions.
How much condensation is
unacceptable?
• A water puddle inside the lamp.
Streaks, drip marks or large droplets
present on the interior of the lens.
What should I do if unacceptable
condensation is present?
• Have your vehicle checked as soon as
possible.
Why do my headlamps turn off
when I have them switched on
when I switch my vehicle off?
• The battery saver turns the headlamps
off after a short period of time after you
switch your vehicle off.
AUTOLAMPS
WHAT ARE AUTOLAMPS
WARNING: The system does not
relieve you of your responsibility to drive
with due care and attention. You may
need to override the system if it does not
turn the headlamps on in low visibility
conditions, for example daytime fog.
Autolamps turn the headlamps on in low
light situations or when the windshield
wipers operate.
AUTOLAMP SETTINGS
1. Using the instrument cluster controls
on the steering wheel, select Settings.
2. Select Vehicle.
3. Select Lighting.
4. Select Autolamp Delay.
5. Select a setting and press the OK
button.
97
2024 Edge (CDQ) Canada/United States of America, enUSA, Edition date: 202306, DOM
Exterior Lighting
EXTERIOR LAMPS
USING THE TURN SIGNAL LAMPS
E162681
E67018
Push the lever up or down to
switch the turn signal lamps on.
Set the lever to the middle position to
switch the turn signal lamps off.
Note: Tap the lever up or down to make the
turn signal lamps flash three times.
Turn Signal Lamp Indicator
E67018
It flashes when you switch the
turn signal lamps on.
Note: An increase in the rate of flashing
warns of a failed turn signal lamp.
SWITCHING THE DAYTIME
RUNNING LAMPS ON AND OFF -
VEHICLES WITH: CONFIGURABLE
DAYTIME RUNNING LAMPS
WARNING: The daytime running
lamps system does not activate the rear
lamps and may not provide adequate
lighting during low visibility driving
conditions. Make sure you switch the
headlamps on, as appropriate, during all
low visibility conditions. Failure to do so
may result in a crash.
1. Using the instrument cluster controls
on the steering wheel, select Settings.
2. Select Vehicle.
3. Select Lighting.
4. Switch Daytime Running Lights on or
off.
The daytime running lamps turn on when
all of the following occur:
• You switch the system on.
• You switch your vehicle on.
• The transmission is not in park (P) for
vehicles with automatic transmissions
or you release the parking brake for
vehicles with manual transmissions.
• The lighting control is in the autolamps
position.
• The headlamps are off.
Note: Other lighting control positions do
not turn on the daytime running lamps.
98
2024 Edge (CDQ) Canada/United States of America, enUSA, Edition date: 202306, DOM
Exterior Lighting
SWITCHING THE DAYTIME
RUNNING LAMPS ON AND OFF -
VEHICLES WITH: DAYTIME
RUNNING LAMPS (DRL)
WARNING: The daytime running
lamps system does not activate the rear
lamps and may not provide adequate
lighting during low visibility driving
conditions. Make sure you switch the
headlamps on, as appropriate, during all
low visibility conditions. Failure to do so
may result in a crash.
Daytime running lamps are always on
unless you switch on the headlamps or
your vehicle is in park (P).
USING THE FRONT FOG LAMPS (If
Equipped)
To switch the lamps on or off:
1. Set the lighting control to the parking
lamps, headlamps or autolamps
position.
Note: When the lighting control is in the
autolamps position, you cannot switch the
fog lamps on unless the low beam
headlamps are on.
2.
Press the button on the
lighting control to switch the front fog
lamps on or off.
Note: Only switch the front fog lamps on
during reduced visibility.
Note: The brightness of the daytime running
lamps may decrease when the front fog
lamps are switched on.
Note: The front fog lamps lights switch off
automatically when high beams are
activated.
Front Fog Lamps Indicator
It illuminates when you switch
the front fog lamps on.
AUTOMATIC HIGH BEAM
CONTROL
HOW DOES AUTOMATIC HIGH
BEAM CONTROL WORK
Automatic high beam control turns the
high beams on if it is dark enough and no
other traffic is present. If it detects an
approaching vehicle’s headlamps or tail
lamps, or street lighting ahead, the system
turns the high beams off.
A camera sensor, centrally mounted
behind the windshield of your vehicle,
continuously monitors conditions to turn
the high beams on and off.
99
2024 Edge (CDQ) Canada/United States of America, enUSA, Edition date: 202306, DOM
Exterior Lighting
E327596
Without automatic high beam
control.
A
With automatic high beam
control.
B
AUTOMATIC HIGH BEAM
CONTROL PRECAUTIONS
WARNING: The system does not
relieve you of your responsibility to drive
with due care and attention. You may
need to override the system if it does not
turn the high beams on or off.
WARNING: The system may not
switch the high beams off if the lights of
oncoming vehicles are hidden by
obstacles, for example guard rails.
WARNING: You may need to
override the system when approaching
other road users.
WARNING: In situations with poor
visibility, such as fog, heavy rain or other
inclement weather, you may need to
override or completely switch off the
system.
AUTOMATIC HIGH BEAM
CONTROL REQUIREMENTS
The system turns the high beams on if all
of the following occur:
• You switch the system on.
• You set the lighting control to the
autolamps position.
• The ambient light level is low enough
that you require high beams.
• There is no traffic in front of your
vehicle.
• The vehicle speed is greater than
approximately 32 mph (52 km/h).
AUTOMATIC HIGH BEAM
CONTROL LIMITATIONS
The system turns the high beams off if any
of the following occur:
• You switch the system off.
• You set the lighting control to any
position except autolamps.
• The ambient light level is high enough
that you do not require high beams.
• The system detects an approaching
vehicle's headlamps or a leading
vehicle's tail lamps.
100
2024 Edge (CDQ) Canada/United States of America, enUSA, Edition date: 202306, DOM
Exterior Lighting
• The system detects severe rain, snow
or fog.
• The system detects street lighting.
• The camera has reduced visibility.
• The vehicle speed falls below
approximately 27 mph (44 km/h).
Note: The deactivation speed may be lower
on curves.
SWITCHING AUTOMATIC HIGH
BEAM CONTROL ON AND OFF
1. Using the instrument cluster controls
on the steering wheel, select Settings.
2. Select Vehicle.
3. Select Lighting.
4. Switch Auto High Beam on or off.
AUTOMATIC HIGH BEAM
CONTROL INDICATORS
E146105
Illuminates to confirm when the
system is ready to assist.
OVERRIDING AUTOMATIC HIGH
BEAM CONTROL
E162679
Push the lever away from you to switch
the high beam on.
Push the lever away from you again to
switch the high beam off.
Push the lever away from you for a third
time to switch automatic high beam
control back on.
AUTOMATIC HIGH BEAM CONTROL – TROUBLESHOOTING
AUTOMATIC HIGH BEAM CONTROL – INFORMATION MESSAGES
DetailsMessage
The camera has reduced visibility. Clean the windshield. If
the message continues to appear, have your vehicle checked
as soon as possible.
Front Camera Low Visib-
ility Clean Screen
The camera has malfunctioned. Wait a short period of time
for the camera to cool down. If the message continues to
appear, have your vehicle checked as soon as possible.
Front Camera Tempor-
arily Not Available
The camera has malfunctioned. Have your vehicle checked
as soon as possible.
Front Camera Malfunc-
tion Service Required
101
2024 Edge (CDQ) Canada/United States of America, enUSA, Edition date: 202306, DOM
Exterior Lighting

Related Topics

Exterior Lighting Control Headlamps Automatic High Beam Control

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot