Get Garage Door Opener -> Programming the Garage Door Opener Guide for Ford Edge SUV Third Generation (2024-2026)

This equipment complies with FCC

radiation exposure limits set forth for an

uncontrolled environment. End Users must

follow the specific operating instructions

for satisfying RF exposure compliance. This

transmitter must be at least 8 in (20 cm)

from the user and must not be co-located

or operating in conjunction with any other

antenna or transmitter.

PROGRAMMING THE GARAGE

DOOR OPENER

To clear all stored codes in the garage door

opener in your vehicle, use the clear

function. To override one button, use the

reprogram function.

Note: Make sure that the garage door and

security device are free from obstruction

when you are programming. Do not program

the system with the vehicle in the garage.

Clearing the Garage Door Opener

E188213

To clear all stored codes in the garage door

opener in the vehicle:

1. Press and hold the outer two function

buttons simultaneously for

approximately 10 seconds until the

indicator above the buttons flashes

rapidly.

2. When the indicator flashes, release the

buttons.

Note: This clears all stored codes. You

cannot erase individual buttons.

Note: You can program a maximum of

three devices. To change or replace any of

the three devices after they have been

initially programmed, you must either clear

all codes, or reprogram each individual

button.

Note: We recommend that upon the sale

or lease termination of your vehicle, you

erase the programmed function buttons for

security reasons.

Reprogramming the Garage Door

Opener

If a button on your garage door opener has

already been programmed, you can

override it. To program a device to a

previously trained button:

1. Press and hold the desired button for

approximately 20 seconds until the

indicator begins to flash.

2. Without releasing the button, proceed

to Step 3 of Programming the

Garage Door Opener to your

Handheld Transmitter.

Programming the Garage Door

Opener to your Handheld

Transmitter

Note: The programming steps below

assume you are programming a HomeLink

that was not previously programmed. If your

HomeLink was previously programmed, you

may need to clear or reprogram your

HomeLink buttons.

Note: Put a new battery in the handheld

transmitter. This allows for quicker training

and accurate transmission of the

radio-frequency signal.

Note: Make sure that the garage door and

security device are free from obstruction

when you are programming. Do not program

the system with the vehicle in the garage.

146

2024 Edge (CDQ) Canada/United States of America, enUSA, Edition date: 202306, DOM

Garage Door Opener (If Equipped)

E188213

To program your in-vehicle HomeLink

function button with your handheld

transmitter:

1. With your vehicle parked outside of the

garage, switch your vehicle on, but do

not start your vehicle.

2. Press and release one of the three

HomeLink function buttons that you

would like to program.

Note: The indicator should begin to flash.

If the indicator does not flash, press and

hold the function button for 20 seconds until

the indicator begins to flash.

3. Hold your handheld garage door

transmitter 1–3 in (2–8 cm) away from

the HomeLink button you want to

program.

4. Press and hold the handheld

transmitter button you want to

program while watching the indicator

on HomeLink. Continue to hold the

handheld button until the HomeLink

indicator flashes rapidly or is

continuously on.

Note: You may need to use a different

method if you live in Canada or have

difficulties programming your gate operator

or garage door opener.

5. Press and hold the HomeLink button

you programmed for two seconds, then

release. You may need to do this twice

to activate the door.

Note: If the indicator stays on, the

programming is complete.

Note: If the HomeLink indicator flashes

rapidly, repeat Step 5.

Note: If your device still does not operate,

you must program your garage door.

6. To program additional buttons, repeat

Steps 1–4.

Note: Make sure you keep the original

remote control transmitter for use in other

vehicles as well as for future system

programming.

Programming the Garage Door

Opener to your Garage Door

Opener Motor

Note: Make sure that the garage door and

security device are free from obstruction

when you are programming. Do not program

the system with the vehicle in the garage.

E142659

1. Press the learn button on the garage

door opener motor and then you have

30 seconds to complete the next two

steps.

2. Return to your vehicle.

147

2024 Edge (CDQ) Canada/United States of America, enUSA, Edition date: 202306, DOM

Garage Door Opener (If Equipped)

E188212

3. Press and hold one of the three

HomeLink function buttons you want

to program for two seconds, then

release.

4. Repeat Step 3. Depending on your

brand of garage door opener, you may

need to repeat this sequence a third

time.

Additional assistance can be found online

at www.homelink.com/Ford or by calling

the toll-free help line at 1-800-355-3515.

Programming the Garage Door

Opener to your Gate Opener Motor

Gate Operator / Canadian

Programming

Canadian radio-frequency laws require

transmitter signals to time-out (or quit)

after several seconds of transmission –

which may not be long enough for

HomeLink to pick up the signal during

programming. Similar to this Canadian law,

some U.S. gate operators are designed to

time-out in the same manner.

Note: If programming a garage door opener

or gate operator, it is advised that you

unplug the device during the cycling process

to prevent possible overheating.

1. Press and release your handheld

transmitter, every two seconds, until

the HomeLink indicator flashes rapidly

or is continuously on.

2. Release the handheld transmitter

button.

3. Press and hold the HomeLink function

button you want to program for two

seconds, then release. You may need

to do this twice to activate the door.

Note: If the indicator stays on, the

programming is complete.

Note: If the HomeLink indicator flashes

rapidly, repeat Step 3.

4. To program additional buttons, repeat

Steps 1–4.

Additional assistance can be found online

at www.homelink.com/Ford or by calling

the toll-free help line at 1-800-355-3515.

GARAGE DOOR OPENER

ADDITIONAL ASSISTANCE

Video Setup Instructions

Universal Garage Door Opener: HomeLink

for Genie Intellicode 2

Universal Garage Door Opener Homelink for

Genie Intellicode

Additional assistance can be found online

at www.homelink.com/Ford or by calling

the toll-free help line at 1-800-355-3515.

148

2024 Edge (CDQ) Canada/United States of America, enUSA, Edition date: 202306, DOM

Garage Door Opener (If Equipped)

Garage Door Opener -> Programming the Garage Door Opener for Your Ford Edge SUV Third Generation (2024-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals