Get Locks and Security -> SECURICODE KEYLESS ENTRY SYSTEM Guide for Ford Explorer SUV Fifth Generation (2005-2011)

Locks and Security

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)

You can use the keyless entry

keypad to:

• lock or unlock the doors without

using a key.

• open the liftgate window.

• activate or deactivate the

autolock feature.

The keypad can be operated with

the factory set 5–digit entry code;

this code is located on the owner’s

wallet card in the glove box, is

marked on the computer module,

and is available from your

authorized dealer. You can also

create your own 5–digit personal

entry code. In the event the wallet card is lost, the factory set code

cannot be reprogrammed.

When pressing the controls on the keypad, press the middle of the

controls to ensure a good activation.

Programming a personal entry code

Up to three personal entry codes may be programmed to the vehicle. To

create your own personal entry code:

1. Enter the factory set code.

2. Within five seconds press the 1 • 2 on the keypad.

3. Enter your personal 5-digit code. Each number must be entered

within five seconds of each other.

4. Press 1 • 2, 3 • 4 or 5 • 6 to indicate which of the three personal

entry code positions you wish to use.

5. The doors will again lock then unlock to confirm that your personal

key code has been programmed to the module.

Tips:

• Do not set a code that uses five of the same number.

• Do not use five numbers in sequential order.

• The factory set code will work even if you have set your own personal

code.

161

2010 Explorer (exp)

Owners Guide, 2nd Printing

USA (fus)

Locks and Security

• If you program a code to a position that already contains a set code,

the previously-set code will be erased.

Erasing personal code

1. Enter the factory set 5–digit code.

2. Within five seconds, press the 1 • 2 on the keypad and release.

3. Press and hold the 1 • 2 for two seconds. This must be done within

five seconds of completing Step 2.

All personal codes are now erased and only the factory set 5–digit code

will work.

Anti-scan feature

If the wrong code has been entered seven times (35 consecutive button

presses), the keypad will go into an anti-scan mode. This mode disables

the keypad for one minute and the keypad lamp will flash.

The anti-scan feature will turn off after:

• one minute of keypad inactivity.

• pressing the

control on the remote entry transmitter.

• the ignition is turned to the on position.

Unlocking and locking the doors, liftgate and liftgate window using

keyless entry

To unlock the driver’s door, enter the factory set 5-digit code or one

of the vehicle’s personal codes. Each number must be pressed within five

seconds of each other. The interior lamps will illuminate.

To unlock all doors and liftgate, press the 3 • 4 control within five

seconds.

To open the liftgate window, press the 5 • 6 control within five

seconds.

To lock all doors, liftgate and liftgate window, press the 7 • 8 and

the 9 • 0 at the same time. Note: The driver’s door must be closed. You

do not need to enter the keypad code first.

SECURILOCKா PASSIVE ANTI-THEFT SYSTEM

SecuriLock௡ passive anti-theft system is an engine immobilization

system. This system is designed to help prevent the engine from being

started unless a coded key programmed to your vehicle is used. The

use of the wrong type of coded key may lead to a “no-start” condition.

162

2010 Explorer (exp)

Owners Guide, 2nd Printing

USA (fus)

Locks and Security -> SECURICODE KEYLESS ENTRY SYSTEM for Your Ford Explorer SUV Fifth Generation (2005-2011)

Related Topics

Locks and Security