Get Keys and Remote Controls -> Remote Control Guide for Ford Fiesta 4 Door Sixth Generation (2009-2016)

Keys and Remote Controls

Intelligent Access(If Equipped)

GENERAL INFORMATION ON

RADIO FREQUENCIES

The system uses a radio frequency signal

to communicate with your vehicle and

authorize your vehicle to unlock when one

of the following conditions are met:

This device complies with Part 15 of the

FCC Rules and with Industry Canada

license-exempt RSS standard(s).

Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) This device

must accept any interference received,

including interference that may cause

undesired operation.

•

You activate the front exterior door

handle switch.

You press the luggage compartment

button.

You press a button on the transmitter.

If excessive radio frequency interference

is present in the area or if the transmitter

battery is low, you may need to

Note: Changes or modifications not

expressively approved by the party

responsible for compliance could void the

user's authority to operate the equipment.

The term IC before the radio certification

number only signifies that Industry Canada

technical specifications were met.

mechanically unlock your door. You can

use the mechanical key blade in your

intelligent access key to open the driver

door in this situation. See Remote

Control (page 42).

The typical operating range for your

transmitter is approximately 33 feet (10

meters). Vehicles with the remote start

feature will have a greater range. One of

the following could cause a decrease in

operating range:

REMOTE CONTROL

Integrated Keyhead Transmitter(If

Equipped)

•

Weather conditions.

Nearby radio towers.

Structures around the vehicle.

Other vehicles parked next to your

vehicle.

The radio frequency used by your remote

control can also be used by other short

distance radio transmissions, for example

amateur radios, medical equipment,

wireless headphones, remote controls and

alarm systems. If the frequencies are

jammed, you will not be able to use your

remote control. You can lock and unlock

the doors with the key.

E142585

Use the key blade to start your vehicle and

unlock or lock the driver door from outside

your vehicle. The transmitter portion

functions as the remote control.

Note: Make sure to lock your vehicle before

leaving it unattended.

Note: If you are in range, the remote control

will operate if you press any button

unintentionally.

Fiesta (CCT), enUSA, Second Printing

Keys and Remote Controls

Reprogramming the Unlocking

Function

Note: When you press the unlock button

either all the doors are unlocked or only the

driver’s door and the liftgate are unlocked.

Pressing the unlock button again unlocks

all the doors.

E162601

You can reprogram the unlocking function

using the remote control so that only the

driver's door is unlocked. This will enable

two-stage unlocking.

Note: Your vehicle’s keys came with a

security label that provides important

vehicle key cut information. Keep the label

in a safe place for future reference.

Press and hold the unlock and lock buttons

on the remote control simultaneously for

at least four seconds with the ignition off.

The direction indicators will flash twice to

confirm the change.

Intelligent Access Transmitter(If

Equipped)

Your intelligent access keys operate the

power locks. The key must be in your

vehicle to activate the push button start

system.

To return to the original unlocking function,

repeat the process.

Replacing the Battery

The intelligent access key also contains a

removable mechanical key blade that you

can use to unlock the driver door.

Note: Refer to local regulations when

disposing of transmitter batteries.

Note: Do not wipe off any grease on the

battery terminals or on the back surface of

the circuit board.

Note: Replacing the battery will not delete

the transmitter from the vehicle. The

transmitter should operate normally.

The remote control uses one coin-type

three-volt lithium battery CR2032 or

equivalent.

E87964

Note: Your vehicle’s back-up keys came

with a security tag that provides important

vehicle key cut information. Keep the tag in

a safe place for future reference.

Fiesta (CCT), enUSA, Second Printing

Keys and Remote Controls

Vehicles Without Intelligent Access

E126281

E126152

Note: Do not touch the battery contacts or

the printed circuit board with the

screwdriver.

1. Insert a screwdriver into the recess on

the back of the key and remove the key

blade.

3. Carefully pry out the battery with the

screwdriver.

4. Install a new battery (3V CR 2032) with

the + facing upward.

5. Assemble the two halves of the remote

control.

6. Install the key blade.

Integrated Keyhead Transmitter

E126153

2. Release the retaining clips with the

screwdriver and separate the two

halves of the remote control.

E138619

1. Twist a thin coin in the slot of the

transmitter near the key ring to remove

the battery cover.

2. Remove the old battery.

Fiesta (CCT), enUSA, Second Printing

Keys and Remote Controls

E138620

3. Insert the new battery. Refer to the

instructions inside the transmitter for

the correct orientation of the battery.

Press the battery down to make sure

it is fully in the housing.

E105362

3. Twist the screwdriver in the position

shown to start separating the two

halves of the remote control.

4. Snap the battery cover back onto the

transmitter.

Intelligent Access Transmitter

E119190

4. Twist the screwdriver in the position

shown to separate the two halves of

the remote control.

E87964

1. Press and hold the buttons on the

edges to release the cover. Carefully

remove the cover.

2. Remove the key blade.

E125860

Fiesta (CCT), enUSA, Second Printing

Keys and Remote Controls -> Remote Control for Your Ford Fiesta 4 Door Sixth Generation (2009-2016)

Related Topics

Popular Owner Manuals

Latest Owner Manuals