Driver Controls for Your Ford Focus 4 Door Second Generation (2004-2010)

Driver Controls  
MULTI-FUNCTION LEVER  
Windshield wiper: Move the lever  
down for a single wipe.  
For intermittent operation, move  
control up one position and adjust  
the rotary control to the desired  
speed.  
For normal operation, move control  
up two positions.  
For high speed operation, move control up three positions.  
Mist function: To mist, push and  
release the windshield washer  
control quickly. The wipers will  
cycle two or three times to clear the  
windshield.  
Windshield washer: To activate  
the windshield washer, push the  
windshield washer control. Release  
control to stop washer fluid spray. The wipers will provide three wipes  
after the wash is turned off.  
Note: Do not operate the washer when the washer reservoir is empty.  
This may cause the washer pump to overheat. Check the washer fluid  
level frequently. Do not operate the wipers when the windshield is dry.  
This may scratch the glass, damage the wiper blades and cause the wiper  
motor to burn out. Before operating the wiper on a dry windshield,  
always use the windshield washer. In freezing weather, be sure the wiper  
blades are not frozen to the windshield before operating the wipers.  
Rear window wiper/washer  
(if equipped)  
Wiper  
Pull the lever towards you for  
intermittent wiping.  
Washer  
Pull the lever further to operate the  
washer.  
45  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
TILT AND TELESCOPE STEERING COLUMN (IF EQUIPPED)  
Pull the locking lever down to adjust  
and telescope the steering column  
position. Return the lever to its  
original position to secure the  
wheel.  
The telescope function is adjusted  
by moving the wheel toward the  
driver to telescope out and toward  
the instrument panel to telescope  
in. Always place both hands  
opposite each other to adjust.  
Never adjust the steering wheel when the vehicle is moving.  
OVERHEAD CONSOLE (IF EQUIPPED)  
The appearance of your vehicle’s overhead console will vary according to  
your option package.  
Storage compartment  
Press the latch to open the storage  
compartment.  
46  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
Installing a garage door opener (if equipped)  
The storage compartment can be converted to accommodate a variety of  
aftermarket garage door openers:  
Place the VELCROhook onto  
the side of the aftermarket  
transmitter opposite of the  
button.  
Place the transmitter into storage  
compartment, button down.  
Place the provided height  
adaptors onto the back of the  
door as needed.  
Close the door.  
Press the depression in the door  
to activate the transmitter.  
AUXILIARY POWER POINT (12VDC)  
Power outlet is designed for accessory plugs only. Do not insert  
any other object in the power outlet as this will damage the  
outlet and blow the fuse. Do not hang any type of accessory or  
accessory bracket from the plug. Improper use of the power  
outlet can cause damage not covered by your warranty.  
The auxiliary power point is located  
on the instrument panel.  
Do not use the power point for  
operating the cigarette lighter  
element (if equipped).  
To prevent the fuse from being  
blown, do not use the power point  
over the vehicle capacity of 12  
VDC/180W.  
47  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
To prevent the battery from being discharged, do not use the power  
point longer than necessary when the engine is not running.  
Always keep the power point caps closed when not being used.  
Cigar lighter (if equipped)  
Do not plug optional electrical accessories into the cigarette lighter  
socket.  
Do not hold the lighter in with your hand while it is heating, this will  
damage the lighter element and socket. The lighter will be released from  
its heating position when it is ready to be used.  
Improper use of the lighter can cause damage not covered by your  
warranty.  
POWER WINDOWS (IF EQUIPPED)  
Do not leave children unattended in the vehicle and do not let  
children play with the power windows. They may seriously injure  
themselves.  
When closing the power windows, you should verify they are free  
of obstructions and ensure that children and/or pets are not in  
the proximity of the window openings.  
Press and hold the bottom part of  
the rocker switch to open the  
window. Press and hold the top part  
of the rocker switch to close the  
window.  
One touch down: Allows the  
driver’s window to open fully  
without holding the control down.  
Press the driver window control completely down then release. Press  
again to stop.  
48  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
Window lock  
The window lock feature allows only  
the driver and front passenger to  
operate the power windows.  
To lock out all the rear window  
controls slide the control to the left.  
Slide the control to the right to  
restore the window controls.  
EXTERIOR MIRRORS  
Power side view mirrors (if equipped)  
To adjust your mirrors:  
1. Rotate the control clockwise to  
adjust the right mirror and rotate  
the control counterclockwise to  
adjust the left mirror.  
2. Move the control in the direction  
you wish to tilt the mirror.  
3. Return to the center position to  
lock mirrors in place.  
Heated mirrors (if equipped)  
Both mirrors are heated  
automatically to remove ice, mist  
and fog when the rear window  
defrost is activated.  
Do not remove ice from the  
mirrors with a scraper or  
attempt to readjust the mirror  
glass if it is frozen in place.  
These actions could cause  
damage to the glass and mirrors.  
49  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
SPEED CONTROL (IF EQUIPPED)  
With speed control set, you can maintain a set speed without keeping  
your foot on the accelerator pedal.  
Do not use the speed control in heavy traffic or on roads that  
are winding, slippery or unpaved.  
Setting speed control  
The controls for using your speed  
control are located on the steering  
wheel for your convenience.  
1. Press the ON control and release  
it.  
2. Accelerate to the desired speed.  
3. Press the SET ACCEL control  
and release it.  
4. Take your foot off the accelerator  
pedal.  
5. The indicator light on the  
instrument cluster will turn on.  
Note:  
Vehicle speed may vary momentarily when driving up and down a  
steep hill.  
If the vehicle speed increases above the set speed on a downhill, you  
may want to apply the brakes to reduce the speed.  
If the vehicle speed decreases more than 10 mph (16 km/h) below  
your set speed on an uphill, your speed control will disengage.  
50  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
Disengaging speed control  
To disengage the speed control:  
Depress the brake pedal or  
Depress the clutch pedal (if equipped).  
Disengaging the speed control will not erase previous set speed.  
Resuming a set speed  
Press the RES (resume) control and  
release it. This will automatically  
return the vehicle to the previously  
set speed.  
Increasing speed while using speed control  
There are two ways to set a higher  
speed:  
Press and hold the SET ACCEL  
control until you get to the  
desired speed, then release the  
control. You can also use the SET  
ACCEL control to operate the  
Tap-Up function. Press and  
release this control to increase  
the vehicle set speed in small  
amounts by 1 mph (1.6 km/h).  
Use the accelerator pedal to get to the desired speed. When the  
vehicle reaches that speed, press and release the SET ACCEL control.  
51  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
Reducing speed while using speed control  
There are two ways to reduce a set  
speed:  
Press and hold the COAST  
control until you get to the  
desired speed, then release the  
control. You can also use the  
COAST control to operate the  
Tap-Down function. Press and  
release this control to decrease  
the vehicle set speed in small  
amounts by 1 mph (1.6 km/h).  
Depress the brake pedal until the  
desired vehicle speed is reached,  
press the SET ACCEL control.  
Turning off speed control  
Press the speed control OFF  
control.  
Note: When you turn off the speed  
control or the ignition, your speed  
control set speed memory is erased.  
52  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
STEERING WHEEL CONTROLS (IF EQUIPPED)  
Remote audio steering column controls (if equipped)  
The remote audio steering column controls may be used to select radio  
or CD mode. The following functions can be carried out using the remote  
control.  
Volume: Pull VOL + towards the  
steering wheel to increase the  
volume.  
Pull VOL - towards the steering  
wheel to decrease the volume.  
SEEK:  
Move the SEEK control  
towards the steering wheel to  
advance to the next preset radio  
station or the next CD track.  
Move the SEEK control  
towards the instrument panel to seek to the next preset radio station  
down the frequency band or the previous CD track.  
Move and hold the SEEK control towards the steering wheel to  
advance to the next radio station.  
Move and hold the SEEK control towards the instrument panel to  
advance to the next radio station down the frequency band.  
MODE: Press to toggle through AM/FM1/FM2/CD modes. Press in all  
modes to abort a traffic message during broadcasting.  
MOON ROOF (SUNROOF) (IF EQUIPPED)  
You can move the glass panel of the moon roof back to open or tilt up to  
ventilate the vehicle.  
Before operating the moon roof you should verify that it is free  
of obstructions and ensure that children and/or pets are not in  
the proximity of moon roof opening.  
Do not let children play with the moon roof or leave children  
unattended in the vehicle. They may seriously hurt themselves.  
53  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
To open the moon roof:  
The moon roof is equipped with an  
automatic, one-touch, express  
opening and closing feature. To stop  
motion at any time during the  
one-touch operation, press the  
control a second time.  
To open the moon roof, press and  
release the rear portion of the  
moon roof control to open.  
To close:  
To close, press and release the front portion of the control.  
Bounce back:  
When an obstacle has been detected in the moon roof opening as the  
moon roof is closing, the moon roof will automatically open and stop at a  
prescribed position.  
Bounce back override:  
To override bounce back, press and hold the front portion of the control.  
For example: Bounce back can be used to overcome the resistance of ice  
on the moon roof or seals.  
To vent:  
To tilt the moon roof into the vent position (when the glass panel is  
closed), press and hold the front portion of the control.  
To close the moon roof from the vent position, press and hold the rear  
portion of the control until the glass panel stops moving.  
Before operating the moonroof you should verify that it is free of  
obstructions and ensure that children and/or pets are not in the  
proximity of moon roof opening.  
Do not let children play with the moon roof or leave children  
unattended in the vehicle. They may seriously hurt themselves.  
Relearning function: In case the moon roof does not close properly  
anymore, follow this relearning procedure.  
Tilt the moon roof into the vent position as far as possible. Release the  
switch.  
54  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
Press and hold the same switch again for 30 seconds until you see the  
moon roof move.  
Release the switch and immediately press and hold it again. The moon  
roof will close, open fully and then close again. Do not release the  
switch before the moon roof has reached the closed position for the  
second time.  
Safety mode: If the system detects a malfunction, it enters a safety  
mode. The moon roof will move about 0.5 seconds at a time and then  
stop again. Press the switch repeatedly until the moon roof is closed.  
Have the system checked by your authorized dealer immediately.  
REMOTE LUGGAGE COMPARTMENT RELEASE (IF EQUIPPED)  
To open the luggage compartment,  
press the control on the instrument  
panel located to the left of the  
cluster.  
The control does not function if the  
vehicle is traveling faster then 4  
mph (7 km/h).  
POSITIVE RETENTION FLOOR MAT  
Do not install additional floor mats on top of the factory installed  
floor mats as they may interfere with the accelerator or the  
brake pedals.  
Position the floor mat so that the  
eyelet is over the pointed end of the  
retention post and rotate forward to  
lock in. Make sure that the mat does  
not interfere with the operation of  
the accelerator, brake pedal or  
clutch pedal (if equipped). To  
remove the floor mat, reverse the  
installation procedure.  
55  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
LUGGAGE COVER  
Models with rear hatch  
Detach the lifting straps on the  
liftgate. Release the cover at the  
sides and pull it out horizontally  
without tilting it.  
Install in reverse order. Make sure  
the cover is properly aligned when  
inserting it.  
Wagon  
Pull out the roller cover and secure  
the retaining points. The cover can  
be removed completely by pressing  
inward on both ends of the support.  
To reduce the risk of injury,  
the luggage cover must be  
properly attached to the mounting  
clips.  
Do not place any objects on the cargo area cover. They may  
obstruct your vision or strike occupants of the vehicle in the  
case of a sudden stop or collision.  
The cover may cause injury in a sudden stop or accident if it is  
not securely installed.  
56  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
LIFTGATE (WAGON ONLY)  
You can open and close the liftgate from outside of the vehicle.  
To open the liftgate, unlock the  
wagon (with the power door locks  
or the remote entry transmitter)  
and push the button next to the  
license plate.  
To close the liftgate, grab the pull  
handle (if equipped) and pull the  
liftgate down. If the tailgate  
doesn’t close due to a load, do  
not use the pull handle to tie the  
liftgate down.  
To lock the liftgate, use the power door locks, or the remote entry  
transmitter to lock the wagon.  
Do not leave the liftgate open while driving. Doing so could cause serious  
damage to the liftgate and its components as well as allowing carbon  
monoxide to enter the vehicle.  
Make sure that the liftgate door is closed to prevent exhaust  
fumes from being drawn into the vehicle. This will also prevent  
passengers and cargo from falling out. If you must drive with the  
liftgate door open, keep the vents open so outside air comes into the  
vehicle.  
57  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)  
Driver Controls  
LUGGAGE RACK (IF EQUIPPED)  
The maximum recommended load is  
220 lbs (100 kg) on the luggage  
rack structure. The load must be  
placed directly on the dealer  
installed cross-bars (if equipped)  
and luggage rack. The vehicle’s roof  
panel is not designed to carry a  
load.  
When loading the luggage rack, it is recommended to evenly distribute  
the load, as well as maintain a low center of gravity. Ensure that the load  
is securely fastened.  
Your fuel economy will decrease when you drive with items on the  
luggage rack. When the rack is loaded, check the tightness of the rear  
adjusting thumbwheel before driving and at each refueling stop.  
Loaded vehicles, with a higher center of gravity, may handle  
differently than unloaded vehicles. Extra precautions, such as  
slower speeds and increased stopping distance, should be taken when  
driving a heavily loaded vehicle.  
58  
2007 Focus (foc)  
Owners Guide (post-2002-fmt)  
USA (fus)