Get Security -> Anti-Theft Alarm Guide for Ford Focus 4 Door Third generation(2010-2017)

Security

The intelligent access key functions as a

PASSIVE ANTI-THEFT

SYSTEM

Note: The system is not compatible with

non-Ford aftermarket remote start systems.

Use of these systems may result in engine

starting problems and a loss of security

protection.

programmed key that operates the driver

door lock and turns on the intelligent

access with push button start system, as

well as a remote control.

If your intelligent access keys are lost or

stolen and you do not have an extra coded

key, you need to have your vehicle towed

to an authorized dealer. You need to erase

the key codes from your vehicle and

program new coded keys.

Note: Metallic objects, electronic devices

or a second coded key on the same key

chain may result in vehicle starting

Store a spare intelligent access key away

from your vehicle in a safe place. Contact

an authorized dealer to purchase

problems, especially if they are too close to

the key when starting your vehicle. Prevent

these objects from touching the coded key

when starting your vehicle. If your vehicle

fails to start, switch the ignition off, move

all objects on the key chain away from the

key and start your vehicle.

additional spare or replacement keys.

Programming a Spare Integrated

Keyhead Transmitter

You can program your own integrated

keyhead transmitter or standard

SecuriLock coded keys to your vehicle. This

procedure will program both the vehicle

immobilizer keycode and the remote entry

portion of the remote control to your

vehicle.

Note: Do not leave a duplicate coded key

in your vehicle. Always take your keys and

lock all doors when leaving your vehicle.

SecuriLock

The system helps prevent the engine from

starting unless you use a coded key

Only use integrated keyhead transmitters

programmed to your vehicle. A message

may appear in the information display.

or standard SecuriLock keys.

You must have two previously

If your vehicle fails to start, the system may

have a fault. Contact an authorized dealer.

A message may appear in the information

display.

programmed coded keys and the new

unprogrammed key readily accessible.

Contact an authorized dealer to have the

spare key programmed if two previously

programmed keys are not available.

Automatic Arming

Make sure that the ignition is switched off

before beginning this procedure. Carry out

all steps within 30 seconds of starting the

sequence. Stop and wait for at least one

minute before starting again if you carry

out any steps out of sequence.

Note: You can program a maximum of eight

coded keys to your vehicle. All eight can be

integrated keyhead transmitters.

The system arms when you switch the

ignition off.

Automatic Disarming

The system disarms when you switch the

ignition on with a coded key.

Replacement Keys

Note: Your vehicle comes with two keys.

Read and understand the entire procedure

before you begin.

Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing

Security

1. Insert the first previously programmed

Programming a Spare Intelligent

Access Key

coded key into the ignition.

2. Switch the ignition from off to on. Keep

the ignition on for at least 3 seconds,

but no more than 10 seconds.

You must have two previously

programmed coded keys and the new

unprogrammed key readily accessible.

Contact an authorized dealer to have the

spare key programmed if two previously

programmed keys are not available.

3. Switch the ignition off and remove the

first coded key from the ignition.

4. After at least 3 seconds but within 10

seconds of switching the ignition off,

insert the second previously coded key

into the ignition.

5. Switch the ignition from off to on. Keep

the ignition on for at least 3 seconds,

but no more than 10 seconds.

6. Switch the ignition off and remove the

second previously programmed coded

key from the ignition.

Make sure that the ignition is switched off

before beginning this procedure. Make sure

that you close all the doors before

beginning and that they remain closed

throughout the procedure. Carry out all

steps within 30 seconds of starting the

sequence. Stop and wait for at least one

minute before starting again if you carry

out any steps out of sequence.

Note: You can program a maximum of eight

7. After at least 3 seconds but within 10

seconds of switching the ignition off

and removing the previously

intelligent access keys to your vehicle.

Read and understand the entire procedure

before you begin.

programmed coded key, insert the new

unprogrammed key into the ignition.

8. Switch the ignition from off to on. Keep

the ignition on for at least six seconds.

9. Remove the newly programmed coded

key from the ignition.

If you have successfully programmed the

coded key, it will start your vehicle and

operate the remote entry system.

If programming was unsuccessful, wait 10

seconds and repeat Steps 1 through 8. If

programming remains unsuccessful, have

your vehicle checked by an authorized

dealer.

Wait 20 seconds and repeat Steps 1

through 9 to program an additional key.

E184385

1. Open the floor console storage

compartment lid.

2. Remove the tray.

Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing

Security

If programming was unsuccessful, wait 10

seconds and repeat Steps 1 through 12. If

programming remains unsuccessful, have

your vehicle checked by an authorized

dealer.

ANTI-THEFT ALARM

The system will warn you of an

unauthorized entry to your vehicle. It will

be triggered if any door, the luggage

compartment or the hood is opened

without using the key, remote control or

keyless entry keypad.

The direction indicators will flash and the

horn will sound if unauthorized entry is

attempted while the alarm is armed.

E184386

3. Place the first programmed intelligent

access key flat on the symbol at the

bottom of the floor console storage

compartment.

Take all remote controls to an authorized

dealer if there is any potential alarm

problem with your vehicle.

4. Press the push button ignition switch.

5. Wait five seconds and then press the

Arming the Alarm

The alarm is ready to arm when there is

not a key in your vehicle. Electronically lock

your vehicle to arm the alarm.

push button ignition switch again.

6. Remove the intelligent access key.

7. Within 10 seconds, place a second

programmed intelligent access key flat

on the symbol.

Disarming the Alarm

8. Press the push button ignition switch.

Disarm the alarm by any of the following

9. Wait five seconds and then press the

actions:

push button ignition switch again.

•

Unlock the doors or luggage

compartment with the remote control

or keyless entry keypad.

10. Remove the intelligent access key.

11.

Within 10 seconds, place the

unprogrammed intelligent access key

flat on the symbol.

•

Switch your vehicle on or start your

vehicle.

12. Press the push button ignition switch.

Use a key in the driver door to unlock

your vehicle, then switch your vehicle

on within 12 seconds.

Programming is now complete. Check that

the remote control functions operate and

your vehicle starts with the new intelligent

access key.

Note: Pressing the panic button on the

remote control will stop the horn and signal

indicators, but will not disarm the system.

Focus (CDH) Canada/United States of America, HM5J 19A321 AA enUSA, Edition date: 201608, First Printing

Security -> Anti-Theft Alarm for Your Ford Focus 4 Door Third generation(2010-2017)

Related Topics

Security

Steering Wheel