Get Seats Guide for Ford Mustang 2 Door Sixth Generation (2015-2023)

SITTING IN THE CORRECT

POSITION

WARNINGS

It is extremely dangerous to ride in

the cargo area inside or outside the

vehicle. In a collision, people riding in

these areas are more likely to be seriously

injured or killed. Do not allow people to ride

in any area of the vehicle that is not fitted

with seats and seatbelts. Be sure that

everyone in your vehicle is in a seat and is

using a seatbelt properly.

Ensure that all parts of passengers

are inside the vehicle when in motion.

Do not recline the seatback too far

as this can cause the occupant to

slide under the seatbelt, resulting in

serious injury in the event of a collision.

Sitting improperly, out of position or

with the seatback reclined too far,

can result in serious injury or death

in the event of a collision. Always sit

upright against your seatback, with your

feet on the floor.

Do not place objects higher than the

seatback to reduce the risk of serious

injury in the event of a collision or

during heavy braking.

E68595

When you use them properly, the seat,

head restraint, seatbelt and air bags will

provide optimum protection in the event

of a collision.

We recommend that you follow these

guidelines:

• Sit in an upright position with the base

of your spine as far back as possible.

• Do not recline the seatback more than

30 degrees.

• Adjust the head restraint so that the

top of it is level with the top of your

head and as far forward as possible.

Make sure that you remain

comfortable.

• Keep sufficient distance between

yourself and the steering wheel. We

recommend a minimum of 25 cm

between your breastbone and the air

bag cover.

• Hold the steering wheel with your arms

slightly bent.

• Bend your legs slightly so that you can

press the pedals fully.

• Position the shoulder strap of the

seatbelt over the center of your

shoulder and position the lap strap

tightly across your hips.

Mustang (CZG) Australia, Vehicles Built From: 07-08-2017, JR3J 19A321 ZAB enAUS, Edition date: 201709, Second Printing

Seats

Make sure that your driving position is

comfortable and that you can maintain full

control of your vehicle.

HEAD RESTRAINTS

WARNINGS

Fully adjust the head restraint before

you sit in or operate your vehicle. This

will help minimize the risk of neck

injury in the event of a crash. Do not adjust

the head restraint when your vehicle is

moving.

Do not remove the head restraint

from an occupied seat.

Note: Adjust the head restraint so that the

top of it is level with the top of your head.

Front Seat Head Restraints

E138642

The head restraints consist of:

An energy absorbing head

restraint.

Two steel stems.B

Guide sleeve adjust and release

button.

Guide sleeve unlock and remove

button.

Adjusting the Head Restraint

Raising the Head Restraint

Pull the head restraint up.

Lowering the Head Restraint

1. Press and hold button C.

2. Push the head restraint down.

Removing the Head Restraint

1. Pull the head restraint up until it

reaches its highest position.

2. Press and hold buttons C and D.

3. Pull the head restraint up.

Installing the Head Restraint

Align the steel stems into the guide sleeves

and push the head restraint down until in

locks.

Front Seat Non-Adjustable Head

Restraints

E174407

The non-adjustable head restraints consist

of a trimmed foam covering over the upper

structure of the seat backrest.

Properly adjust the seat backrest to an

upright driving or riding position, so that

the head restraint is positioned as close as

possible to the back of your head.

Mustang (CZG) Australia, Vehicles Built From: 07-08-2017, JR3J 19A321 ZAB enAUS, Edition date: 201709, Second Printing

Seats

Tilting Head Restraints

The front seat head restraints tilt for extra

comfort.

E144727

1. Adjust the seat backrest to an upright

driving or riding position.

2. Pivot the head restraint forward toward

your head to the desired position.

After the head restraint reaches the

forward-most tilt position, pivoting it

forward again will then release it to the

rearward, untilted position.

MANUAL SEATS

WARNING

Rock the seat backward and forward

after releasing the lever to make sure

that it is fully engaged.

The manual front seats may consist of:

E174553

A bar to move the seat backward

and forward.

A lever to adjust the height of the

seat.

A lever to adjust the angle of the

seatback.

POWER SEATS (If Equipped)

WARNINGS

Do not adjust the driver seat or

seatback when your vehicle is

moving. Adjusting your seatback

while your vehicle is in motion may cause

loss of control of your vehicle.

Mustang (CZG) Australia, Vehicles Built From: 07-08-2017, JR3J 19A321 ZAB enAUS, Edition date: 201709, Second Printing

Seats

WARNINGS

Reclining the seatback can cause an

occupant to slide under the seat’s

seatbelt, resulting in severe personal

injuries in the event of a crash.

E187770

The power seat control is located on the

outboard side of the seat. Move the control

in the direction of the arrows to raise or

lower the seat cushion or to move the seat

forward, backward, up or down.

Power Lumbar (If Equipped)

The power lumbar control is located on

the side of the driver seat.

E187771

Press one side of the control to increase

lower back firmness. Press the other side

of the control to decrease lower back

firmness.

MEMORY FUNCTION (If Equipped)

WARNINGS

Before activating the memory seat,

make sure that the area immediately

surrounding the seat is clear of

obstructions and that all occupants are

clear of moving parts.

Do not use the memory function

when your vehicle is moving.

This feature automatically recalls the

position of the following features:

• Driver seat.

• Power mirrors.

The memory control is on the driver door.

E142554

Saving a PreSet Position

1. Switch the ignition on.

2. Adjust the memory features to your

desired position.

3. Press and hold the desired preset

button until you hear a single tone.

You can save up to three preset memory

positions. You can save a memory preset

at any time.

Mustang (CZG) Australia, Vehicles Built From: 07-08-2017, JR3J 19A321 ZAB enAUS, Edition date: 201709, Second Printing

Seats

Recalling a PreSet Position

Press and release the preset button

associated with your desired driving

position. The memory features move to

the position stored for that preset.

Note: You can only recall a preset memory

position when you switch the ignition off, or

when the transmission is in park (P) or

neutral (N) if the ignition is on and the

vehicle is not moving.

You can also recall a preset memory

position by:

• Pressing the unlock button on your

intelligent access key fob if it is linked

to a preset position.

• Unlocking the intelligent driver door

handle if a linked key fob is present.

Note: Using a linked key fob to recall your

memory position when the ignition is off

moves the seat to the easy entry position.

Note: Pressing any seat or mirror

adjustment control, or any memory button

during a memory recall, cancels the

operation.

Seat recall movement also stops if you

drive your vehicle.

Linking a PreSet Position to your

Remote Control or Intelligent

Access Key Fob

Your vehicle can save the preset memory

positions for up to three remote controls

or intelligent access (IA) keys.

1. With the ignition on, move the memory

features to the desired positions.

2. Press and hold the desired preset

button for about five seconds. A tone

sounds after about two seconds.

Continue holding until you hear a

second tone.

3. Within three seconds, press the lock

button on the remote control you are

linking.

To unlink a remote control, follow the

same procedure – except in step 3, press

the unlock button on the remote control.

Note: If more than one linked remote

control or intelligent access key is in range,

the memory function moves to the settings

of the first key stored.

REAR SEATS

WARNINGS

When folding the seat backrest

down, take care not to get your

fingers caught in the mechanism.

Make sure that the seats and the

seat backrests are secure and fully

locked in their catches.

Accessing the Rear Seats

E207088

Use the seatback release to fold the back

of the front seat forward for rear seat

access. The release handle is on the upper

back of the front seat. The seatback has

memory and locks automatically in the

original position.

Mustang (CZG) Australia, Vehicles Built From: 07-08-2017, JR3J 19A321 ZAB enAUS, Edition date: 201709, Second Printing

Seats

Second Row Split-Folding Rear

Seat

E175611

To lower the seatback(s):

1. Pull the strap to release the seatback.

2. Fold the seatback down.

Returning the Seatbacks to the Upright

Position

When raising the seatback(s), push the

top of the seatback rearward and make

sure you hear the seat latch into place. Pull

down on the seatback to make sure that

it has locked into position.

CLIMATE CONTROLLED SEATS

Heated Seats

WARNING

People who are unable to feel pain

to their skin because of advanced

age, chronic illness, diabetes, spinal

cord injury, medication, alcohol use,

exhaustion or other physical conditions,

must use caution when using the heated

seat. The heated seat may cause burns

even at low temperatures, especially if

used for long periods of time. Do not place

anything on the seat that may block the

heat, such as a blanket or cushion. This can

cause the heated seat to overheat. Do not

puncture the seat with pins, needles or

other pointed objects. This damages the

heating element and can cause the heated

seat to overheat. An overheated seat may

cause serious personal injury.

Note: Do not do the following:

• Place heavy objects on the seat.

• Operate the seat heater if water or any

other liquid spills on the seat. Allow the

seat to dry thoroughly.

• Operate the heated seats unless the

engine is running. Doing so can cause

the battery to lose charge.

E146322

Press the heated seat symbol to cycle

through the various heat settings and off.

More indicator lights indicate warmer

settings.

Mustang (CZG) Australia, Vehicles Built From: 07-08-2017, JR3J 19A321 ZAB enAUS, Edition date: 201709, Second Printing

Seats

Cooled Seats

The cooled seats only function when the

engine is running.

E146309

Press the cooled seat symbol to cycle

through the various cool settings and off.

More indicator lights indicate cooler

settings.

If the engine falls below 350 RPM while

the cooled seats are on, the feature turns

itself off. You will need to reactivate it.

Mustang (CZG) Australia, Vehicles Built From: 07-08-2017, JR3J 19A321 ZAB enAUS, Edition date: 201709, Second Printing

Seats

Seats for Your Ford Mustang 2 Door Sixth Generation (2015-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals