2023-2026 Honda Civic 4 Door Driving -> When Driving User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driving -> When Driving for Your Honda Civic 4 Door Eleventh Generation (2023-2026)

When Driving  
Starting the Engine  
1. Make sure the parking brake is applied.  
u The parking brake and brake system  
indicator (red) comes on for 30 seconds  
when you pull up the electric parking  
brake switch.  
1Starting the Engine  
Keep your foot firmly on the brake pedal when  
starting the engine.  
Theengineishardertostartincoldweatherandinthinner  
air found at altitudes above 8,000 feet (2,400 meters).  
When starting the engine in cold weather, turn off all  
electrical accessories such as the lights, climate  
control system, and rear defogger in order to reduce  
battery drain.  
Electric Parking Brake Switch  
Brake Pedal  
Continuously variable transmission models  
2. Check that the transmission is in (P, then  
depress the brake pedal.  
If you live in a region where winter is extremely cold,  
an engine block heater will improve starting and  
warming of the engine. Consult a dealer for details.  
u Although it is possible to start the vehicle  
If the exhaust system sounds abnormal or you can  
smell exhaust gas inside the vehicle, have your vehicle  
checked by a dealer. There may be a problem with  
the engine or exhaust system.  
in (N, it is safer to start it in (P  
.
Bring the keyless remote close to the ENGINE  
START/STOP button if the battery in the keyless  
remote is weak.  
2 If the Keyless Remote Battery is Weak  
P. 781  
Manual transmission models  
Clutch Pedal  
2. Check that the shift lever is in (N. Then  
depress the brake pedal with your right  
foot, and the clutch pedal with your left  
foot.  
The engine may not start if the keyless remote is  
subjected to strong radio waves.  
Do not hold the ENGINE START/STOP button to  
start the engine.  
If the engine does not start, wait at least 30 seconds  
before starting the engine again.  
u The clutch pedal must be fully depressed  
to start the engine.  
Brake Pedal  
Continued  
491  
uuWhen DrivinguStarting the Engine  
All models  
1Starting the Engine  
3. Press the ENGINE START/STOP button  
without depressing the accelerator pedal.  
The immobilizer system protects your vehicle from  
theft. If an improperly coded device is used, the  
engine's fuel system is disabled.  
2 Immobilizer System P. 195  
492  
uuWhen DrivinguStarting the Engine  
1Remote Engine Start*  
Remote Engine Start*  
■
You can remotely start the engine using the keyless remote.  
3
WARNING  
Carbon monoxide gas is toxic and can  
rapidly accumulate in closed or even partly  
enclosed areas.  
■
To start the engine  
Press the  
the  
button, then press and hold  
button.  
LED: Blinks when any  
button is pressed.  
u Some exterior lights flash once.  
Breathing it can cause unconsciousness and  
even kill you.  
Never use the remote engine starter with  
the vehicle parked in a garage or other  
areas with limited ventilation.  
If the engine starts successfully, some exterior  
lights flash six times.  
The remote engine start may violate local laws.  
Before using the remote engine start, check your  
local laws.  
If there are buildings and obstacles between your  
vehicle and the remote, the range will be reduced.  
This distance may vary by external electrical  
interference.  
If the engine does not start, exterior lights will  
not flash.  
u Go within the range, and try again.  
* Not available on all models  
Continued  
493  
uuWhen DrivinguStarting the Engine  
1Remote Engine Start*  
When started remotely, the engine automatically shuts off after 10 minutes of idling  
and/or the brake pedal and ENGINE START/STOP button have not been pressed  
simultaneously.  
The engine may not start by the remote engine start  
if:  
•
You have disabled a remote engine start setting  
using the driver information interface* or audio/  
information screen*.  
To extend the run time for another 10 minutes during the first run, press the  
button, then press and hold the  
button.  
u Some exterior lights flash six times if a 10-minute extension request was  
transmitted successfully.  
2 Settings P. 138  
2 Customized Features P. 390  
The power mode is not in VEHICLE OFF.  
•
•
•
The transmission is in a position other than (P  
The hood is open, or any door or the hatch is  
unlocked.  
.
•
You have already used the remote twice to start  
the engine.  
•
•
•
•
•
•
Another registered keyless remote is in the vehicle.  
There is any antenna failure.  
The door is unlocked with the built-in key.  
The engine oil pressure is low.  
The engine coolant temperature is extremely high.  
The security system alarm is not set.  
* Not available on all models  
494  
uuWhen DrivinguStarting the Engine  
1Remote Engine Start*  
The engine may stop while it is running if:  
■
To stop the engine  
Press and hold the  
second.  
button for one  
•
You do not start the vehicle within 10 minutes of  
starting the engine with the keyless remote.  
The engine is stopped by using the keyless remote.  
The security system alarm is not set.  
The door is unlocked with the built-in key.  
The hood is open, or any door, or the hatch is  
unlocked.  
•
•
•
•
•
•
•
•
•
You press the shift lever release button.  
The engine coolant temperature is extremely high.  
The battery is low.  
If the engine stops successfully, the exterior  
lights flash once.  
The engine oil pressure is low.  
The malfunction indicator lamp comes on if there is  
a problem with the emissions control systems.  
While the engine is running, the vehicle will  
automatically precondition inside the vehicle.  
When it is warm outside:  
When the remote is out of the keyless access  
system range, the exterior lights will not flash.  
The engine will not stop.  
•
The climate control system is activated in  
recirculation mode.  
When it is cold outside:  
•
The defroster is activated at a moderately warm  
u Go within the range, and try again.  
temperature.  
•
The rear defogger, heated door mirrors*, front seat  
heaters* and heated steering wheel* are activated.  
2 Rear Defogger/Heated Door Mirror*  
Button P. 216  
2 Front Seat Heaters* P. 247  
2 Heated Steering Wheel* P. 246  
* Not available on all models  
Continued  
495  
uuWhen DrivinguStarting the Engine  
1Starting to Drive  
Starting to Drive  
■
Manual transmission models with Auto Idle Stop  
Engine Restart Function  
Continuously variable transmission models  
When the engine was started using the  
button on the keyless remote  
If the engine stalls, fully depress the clutch pedal  
within three seconds. The engine may automatically  
restart under certain conditions. Otherwise, follow  
the standard procedure.  
1. Depress and hold the brake pedal, then press the ENGINE START/STOP button.  
When the engine was started in any case  
2. Keeping your right foot on the brake pedal, put the transmission into (D. Select  
(R when reversing.  
2 Starting the Engine P. 491  
3. With the parking brake applied, release the brake pedal and gently depress the  
accelerator pedal.  
When the engine was started using the  
on the keyless remote  
button  
u Make sure the parking brake and brake system indicator (red) goes off.  
2 Parking Brake P. 655  
The engine stops when the transmission is taken out  
of (P before the ENGINE START/STOP button is  
pressed. Follow step 1 when starting to drive.  
■
Hill start assist system  
You can also release the parking brake by pressing  
the electric parking brake switch while depressing the  
brake pedal.  
Hill start assist keeps the brake engaged briefly to help prevent the vehicle from  
rolling on inclines as you move your foot from the brake pedal to the accelerator.  
When facing downhill, you can start your vehicle  
more smoothly by manually releasing it with the  
electric parking brake switch than by releasing it with  
the accelerator pedal.  
Continuously variable transmission models  
Put the transmission into (D  
(S*, or (L* when facing uphill, or (R when facing  
downhill, then release the brake pedal.  
,
1Hill start assist system  
Manual transmission models  
Hill start assist may not prevent the vehicle from  
rolling downhill on a very steep or slippery slope, and  
will not operate on small inclines.  
Depress the clutch pedal, and shift to one of the forward gears when facing uphill,  
or (R when facing downhill, then release the brake pedal.  
Hill start assist is not a replacement for the parking  
brake.  
Hill start assist will operate even when VSA® is  
switched off.  
* Not available on all models  
496  
uuWhen DrivinguStarting the Engine  
1Stopping the Engine  
Stopping the Engine  
■
You can turn the engine off when the vehicle is completely stopped.  
The power mode will automatically turn to VEHICLE  
OFF about 20 minutes after the following conditions  
have been met:  
Continuously variable transmission models  
•
A door has been opened, such as when leaving the  
vehicle.  
The driver's seat belt is not fastened.  
1. Put the transmission into (P.  
2. Press the ENGINE START/STOP button.  
•
Manual transmission models  
Continuously variable transmission models  
The transmission is in (P  
Manual transmission models  
•
.
• If the transmission is in (N, press the ENGINE START/STOP button.  
• If the transmission is in any gear other than (N, depress the clutch pedal, then  
press the ENGINE START/STOP button.  
•
The vehicle is completely stopped.  
497  
uuWhen DrivinguPrecautions While Driving  
Precautions While Driving  
1Precautions While Driving  
In Rain  
■
Avoid driving in deep water and on flooded roads. This can damage the engine or  
driveline, or cause electrical component failure.  
Continuously variable transmission models  
NOTICE  
Do not operate the shift lever while pressing the  
accelerator pedal. You could damage the  
transmission.  
Other Precautions  
■
If there is a strong impact with something under the vehicle, stop in a safe location.  
Check the underside of the vehicle for damage or any fluid leaks.  
NOTICE  
If you repeatedly turn the steering wheel at an  
extremely low speed, or hold the steering wheel in  
the full left or right position for a while, the electric  
power steering (EPS) system heats up. The system  
goes into a protective mode, and limits its  
performance. The steering wheel becomes harder  
and harder to operate. Once the system cools down,  
the EPS system is restored.  
Repeated operation under these conditions can  
eventually damage the system.  
If the power mode is set to ACCESSORY while  
driving, the engine will shut down and all steering  
and brake power assist functions will stop, making it  
difficult to control the vehicle.  
Do not select (N while driving as you will lose engine  
braking (and acceleration) performance.  
During the first 600 miles (1,000 km) of operation,  
avoid sudden acceleration or full throttle operation so  
as not to damage the engine or powertrain.  
498  
uuWhen DrivinguPrecautions While Driving  
1Precautions While Driving  
Avoid hard braking for the first 200 miles (300 km)  
after purchasing your new vehicle or replacing the  
brake pads or rotors, to allow for proper break-in.  
Models with Auto Idle Stop  
NOTICE  
The following can damage the under spoiler:  
•
•
•
•
Parking the vehicle by a parking block  
Parallel parking along the road shoulder  
Driving towards the bottom of a hill  
Driving up or down to a different surface level  
(such as a road shoulder)  
•
•
Driving on a rutted or bumpy road  
Driving on a road with potholes  
Models without Auto Idle Stop  
NOTICE  
The following can damage the under spoiler, under  
covers, front bumper, rear diffuser, and side sill:  
•
•
•
•
Parking the vehicle by a parking block  
Parallel parking along the road shoulder  
Driving towards the bottom of a hill  
Driving up or down to a different surface level  
(such as a road shoulder)  
•
•
•
Driving on a rutted or bumpy road  
Driving on a road with potholes.  
Driving over speed bump.  
499  
uuWhen DrivinguContinuously Variable Transmission*  
Continuously Variable Transmission*  
Creeping  
■
When the engine runs at higher idle speeds, the creeping force increases.  
Keep the brake pedal firmly depressed when stopped.  
Kickdown  
■
Quickly depressing the accelerator pedal while driving uphill may cause the  
transmission to drop to a lower ratio, unexpectedly increasing vehicle speed.  
Depress the accelerator pedal carefully, especially on slippery roads and curves.  
* Not available on all models  
500  
uuWhen DrivinguShifting  
Continuously variable transmission models without paddle shifter  
Shifting  
1Shifting  
You cannot change the power mode from ON to  
VEHICLE OFF unless the shift position is in (P  
Change the shift position in accordance with your driving needs.  
.
■
Shift positions  
The vehicle may move very slightly even in (N while  
the engine is cold.  
Park  
Depress the brake pedal firmly and, when necessary,  
apply the parking brake.  
Used when parking or starting the  
engine  
Reverse  
Used when reversing  
Neutral  
Transmission is not locked  
Drive  
Used for normal driving  
Drive (S)  
Used:  
●
For better acceleration  
To increase engine braking  
When going up or down hills  
●
●
Release Button  
Low  
●
Used to further increase engine braking  
Used when going up or down hills  
●
Continued  
501  
uuWhen DrivinguShifting  
1Shift Operation  
Shift Operation  
■
NOTICE  
When you change the shift position from (D to (R  
and vice versa, come to a complete stop and keep the  
brake pedal depressed.  
Operating the shift lever before the vehicle has come  
to a complete standstill can damage the transmission.  
Use the shift position indicator to check the lever  
position before pulling away.  
Shift Position Indicator  
Tachometer Red Zone  
(Transmission System Indicator)  
If the transmission system indicator blinks when  
driving, in any shift position, there is a problem with  
the transmission.  
Depress the brake pedal and press the shift lever release  
button to shift.  
Avoid sudden acceleration and have the transmission  
checked by a dealer as soon as possible.  
Shift without pressing the shift lever release button.  
Press the shift lever release button and shift.  
The fuel supply may be cut off if you drive at engine  
speeds in or over the tachometer red zone (engine  
speed limit). If this happens, you may experience a  
slight jolt.  
It may not be possible to operate the shift lever if the  
brake pedal is applied while the shift lever release  
button is held down.  
Depress the brake pedal first.  
When shifting positions in extremely low  
temperatures (-22°F/-30°C), there may be a short  
delay before the shift position is displayed. Always  
confirm you are in the correct shift position before  
driving.  
502  
uuWhen DrivinguShifting  
Continuously variable transmission models with paddle shifter  
Shifting  
Change the shift position in accordance with your driving needs.  
1Shifting  
You cannot change the power mode from ON to  
VEHICLE OFF unless the shift position is in (P  
■
Shift positions  
.
The vehicle may move very slightly even in (N while  
the engine is cold.  
Park  
Depress the brake pedal firmly and, when necessary,  
apply the parking brake.  
Used when parking or starting the  
engine  
Reverse  
Used when reversing  
Neutral  
Transmission is not locked  
Drive  
Used:  
●
For normal driving  
When temporarily driving in the  
●
7-speed manual shift mode  
When driving in the 7-speed  
●
manual shift mode (when driving  
in SPORT mode)  
Release Button  
Continued  
503  
uuWhen DrivinguShifting  
1Shift Operation  
Shift Operation  
■
NOTICE  
When you change the shift position from (D to (R  
and vice versa, come to a complete stop and keep the  
brake pedal depressed.  
Models with A-type meter  
Models with B-type meter  
Tachometer Red Zone  
Operating the shift lever before the vehicle has come  
to a complete standstill can damage the transmission.  
Use the shift position indicator to check the lever  
position before pulling away.  
M (7-Speed Manual Shift Mode)  
Indicator/Shift Indicator  
If the transmission system indicator blinks when  
driving, in any shift position, there is a problem with  
the transmission.  
Shift Position Indicator  
Avoid sudden acceleration and have the transmission  
checked by a dealer as soon as possible.  
(Transmission System Indicator)  
The fuel supply may be cut off if you drive at engine  
speeds in or over the tachometer red zone (engine  
speed limit). If this happens, you may experience a  
slight jolt.  
Press the shift lever release button and shift.  
Depress the brake pedal and press the shift lever release  
button to shift.  
It may not be possible to operate the shift lever if the  
brake pedal is applied while the shift lever release  
button is held down.  
Shift without pressing the shift lever release button.  
Depress the brake pedal first.  
When shifting positions in extremely low  
temperatures (-22°F/-30°C), there may be a short  
delay before the shift position is displayed. Always  
confirm you are in the correct shift position before  
driving.  
504  
uuWhen DrivinguShifting  
17-Speed Manual Shift Mode  
7-Speed Manual Shift Mode  
■
In the 7-speed manual shift mode, the transmission  
shifts up or down by operating either paddle shifter  
under the following conditions:  
Use the paddle shifters to change between 1st and 7th speeds without releasing  
your hands from the steering wheel. The transmission switches to the 7-speed  
manual shift mode when you pull a paddle shifter while driving. This mode is useful  
when engine braking is needed.  
Shift Up: The engine speed reaches the lowest  
threshold of the higher speed position.  
Shift Down: The engine speed reaches the highest  
threshold of the lower speed position.  
■
When the transmission is in (D:  
The shift mode goes into the 7-speed manual shift mode temporarily, and the  
number is displayed in the shift indicator.  
When the engine speed reaches near the tachometer  
red zone, the transmission shifts up automatically.  
When the engine speed reaches the lowest threshold  
of the selected speed position, the transmission shifts  
down automatically.  
The 7-speed manual shift mode is canceled automatically if you drive at constant  
speed or accelerate, and the number in the shift indicator goes off.  
You can cancel this mode by pulling the (+ paddle shifter for a few seconds.  
The 7-speed manual shift mode is especially useful when reducing the vehicle speed  
temporarily before making a turn.  
Operating the paddle shifters on slippery surfaces  
may cause the tires to lock up. In this case, the 7-  
speed manual shift mode is canceled and goes back  
to the normal (D driving mode.  
■
When the transmission is in (D with SPORT mode:  
The shift mode goes into the 7-speed manual shift mode. The M indicator and the  
speed number are displayed in the shift indicator. As the vehicle speed slows down,  
the transmission automatically shifts down accordingly. When the vehicle comes to  
a stop, it automatically shifts down into 1st.  
If the vehicle speed increases and the engine speed reaches near the tachometer red  
zone, the transmission automatically shifts up.  
You can only pull away in 1st speed.  
When canceling the 7-speed manual shift mode, use the DRIVE MODE switch to  
select other than SPORT mode or pull the (+ paddle shifter for a few seconds.  
When the 7-speed manual shift mode is canceled, the M indicator and shift  
indicator will turn off.  
Continued  
505  
uuWhen DrivinguShifting  
17-Speed Manual Shift Mode Operation  
7-Speed Manual Shift Mode Operation  
■
Each paddle shift operation makes a single speed  
change.  
To change continuously, release the paddle shifter  
before pulling it again for the next speed.  
(- Paddle Shifter  
(Shift down)  
(+ Paddle Shifter  
(Shift up)  
The shift indicator blinks when you cannot shift up or  
down. It indicates that your vehicle speed is not in its  
allowable shifting range.  
Slightly accelerate to shift up and decelerate to shift  
down while the indicator is blinking.  
Downshifting when pulling  
the (- paddle shifter  
(Changes to lower speed  
number)  
Upshifting when pulling  
the (+ paddle shifter  
(Changes to higher speed  
number)  
506  
uuWhen DrivinguShifting  
Manual transmission models  
Shifting  
1Shift Lever Operation  
Shift Lever Operation  
■
Fully depress the clutch pedal to operate the shift lever and change gears, then  
slowly release the pedal.  
NOTICE  
Do not shift to (R before the vehicle comes to a  
complete stop.  
Shifting to (R before stopping can damage the  
transmission.  
Depress the clutch pedal, and pause for a few seconds before shifting into (R, or  
shift into one of the forward gears for a moment. This stops the gears so they do not  
“grind.”  
NOTICE  
Before downshifting, make sure the engine will not  
go into the tachometer red zone. Should this occur, it  
can severely damage your engine.  
When you are not shifting, do not rest your  
foot on the clutch pedal. This can cause your  
clutch to wear out faster.  
Models without Auto Idle Stop  
There is a metallic part on the shift lever. If you leave  
the vehicle parked outside for a long time on a hot  
day, be careful before moving the shift lever. Because  
of heat, the shift lever may be extremely hot. If the  
outside temperature is low, the shift lever may feel  
cold.  
If you exceed the maximum speed for the gear you  
are in, the engine speed will enter into the  
tachometer red zone. When this happens, you may  
experience a slight jolt.  
Continued  
507  
uuWhen DrivinguShifting  
1Rev Match System*  
Rev Match System*  
■
Adjusts the engine's RPM to match the optimal speed of the gear that is about to be  
engaged.  
You can turn off the rev match system using the  
audio/information screen.  
2 Customized Features P. 390  
2 Drive Mode Switch* P. 527  
If you depress the accelerator pedal while changing  
gears, the system may give priority to inputs from the  
accelerator pedal depending on the amount of  
depression of the accelerator pedal.  
■
Limitations  
The rev match system will not activate under the following conditions:  
• You are shifting into a lower gear, but the system has determined that the engine  
will over rev.  
If the message below appears, there may be a  
problem with the system. The rev match system may  
not operate, but you can perform regular gear  
shifting.  
• You are shifting into 1st gear from a higher gear.  
• Engine RPM is low and you are shifting into a lower gear in sequential order.  
• The system has determined that the engine will be at idling speed after you have  
shifted into a higher gear.  
Have the system checked by a dealer.  
• The clutch pedal is not fully depressed.  
The rev match system may deactivate if the clutch pedal is fully depressed for a  
extended period of time.  
* Not available on all models  
508  
uuWhen DrivinguShifting  
1Shift Up/Down Indicators  
Shift Up/Down Indicators  
■
This indicator will not prompt you to downshift to  
increase engine braking. It is up to you to downshift  
to increase engine braking when driving downhill.  
Come on to inform you that upshifting or  
downshifting is necessary to prevent the  
engine from over revving or stalling.  
Models with A-type meter  
Always shift down at the appropriate vehicle speed.  
The shift up indicator: Comes on when  
upshifting is recommended.  
The shift down indicator does not come on when  
downshifting from (2 to (1  
.
The shift down indicator: Comes on when  
downshifting is recommended.  
Road and traffic conditions may require you to shift  
at times other than those indicated.  
Models with B-type meter  
Models without Auto Idle Stop  
*1  
*1: When using the +R gauge  
Continued  
509  
uuWhen DrivinguShifting  
1Reverse Lockout  
Reverse Lockout  
■
Have your vehicle checked by a dealer if you have to  
go through this procedure repeatedly.  
The manual transmission has a lockout mechanism that stops you from accidentally  
shifting into (R from a forward gear while the vehicle is moving above a certain  
speed.  
If you cannot shift to (R when the vehicle is stopped, do the following:  
1. Depress the clutch pedal, move the shift  
lever all the way to the left, and shift to (R  
2. If you still cannot shift into (R, apply the  
parking brake, and set the power mode to  
ACCESSORY or VEHICLE OFF.  
.
3. Depress the clutch pedal and shift into (R  
4. Keep depressing the clutch pedal and start  
the engine.  
.
510  
uuWhen DrivinguECON Button*  
ECON Button*  
1ECON Button*  
Models with A-type meter  
While in the ECON mode, the climate control system  
has greater temperature fluctuation.  
Due to emergency brakes operation or driving  
conditions, you may not be able to change the mode.  
ECON Mode Indicator  
ECON Button  
Models with B-type meter  
ECON Mode Indicator  
ECON Button  
The ECON button turns the ECON mode on and off.  
The ECON mode helps you improve your fuel economy by adjusting the  
performance of the engine, transmission* and climate control system.  
* Not available on all models  
511  
uuWhen DrivinguAuto Idle Stop  
Continuously variable transmission models  
Auto Idle Stop  
To help maximize fuel economy, the engine automatically stops when the vehicle  
comes to a stop, depending on environmental and vehicle operating conditions. The  
indicator (green) comes on at this time.  
The environmental and vehicle conditions that  
impact Auto Idle Stop system operation are  
varied.  
1Auto Idle Stop  
The 12-volt battery installed in this vehicle is  
specifically designed for a model with Auto Idle Stop.  
Using a 12-volt battery other than this specified type  
may shorten the 12-volt battery life, and prevent  
Auto Idle Stop from activating. If you need to replace  
the 12-volt battery, make sure to select the specified  
type. Ask a dealer for more details.  
2 Auto Idle Stop Activates When: P. 514  
2 Auto Idle Stop may not activate when:  
P. 515  
The duration of the Auto Idle Stop operation:  
•
Increase in the ECON mode, compared to when  
the ECON mode is off, with climate control in use.  
The engine then restarts once the vehicle is  
about to move again, and the indicator  
(green) goes off.  
Auto Idle Stop  
Indicator (Green)  
Models without DRIVE MODE switch  
2 ECON Button* P. 511  
Models with DRIVE MODE switch  
2 Drive Mode Switch* P. 523  
2 The Engine Automatically Restarts When:  
P. 516  
If the driver's door is opened while the  
indicator (green) comes on, a buzzer sounds  
to notify you that the Auto Idle Stop function  
is in operation.  
A message associated with Auto Idle Stop  
appears on the driver information interface.  
* Not available on all models  
512  
uuWhen DrivinguAuto Idle Stop  
The Auto Idle Stop suspend indicator comes  
on and a message appears on the gauge  
when the Auto Idle Stop system cannot be  
activated.  
2 Indicators P. 96  
2 Auto Idle Stop System ON/OFF P. 513  
Auto Idle Stop  
Suspend Indicator  
1Auto Idle Stop System ON/OFF  
Auto Idle Stop System ON/OFF  
■
If you turn off the Auto Idle Stop system while it is  
activated, the engine will restart.  
To turn the Auto Idle Stop system off, press  
Auto Idle Stop OFF  
Indicator  
this button. The Auto Idle Stop system stops.  
u Auto Idle Stop system will stop, the  
indicator will come on and a message  
appears on the gauge.  
If you hold the Auto Idle Stop OFF button, you can  
disable idle stop messages.  
2 Indicators P. 96  
The Auto Idle Stop system is turned on every  
time you start the engine, even if you turned it  
off the last time you drove the vehicle.  
Auto Idle Stop  
OFF Button  
Continued  
513  
uuWhen DrivinguAuto Idle Stop  
1Auto Idle Stop Activates When:  
Auto Idle Stop Activates When:  
■
Do not open the hood while the Auto Idle Stop  
function is activated. If the hood is opened, the  
engine will not restart automatically.  
In this case, restart the engine with the ENGINE  
START/STOP button.  
The vehicle stops with the transmission in (D and the brake pedal depressed.  
When you put the transmission into (P quickly with depressing the brake pedal, the  
Auto Idle Stop continues to operate, even if the brake pedal is released.  
u If you depress the brake pedal, the engine may automatically restart.  
2 Starting the Engine P. 491  
■
Auto Idle Stop does not activate when:  
• The Auto Idle Stop OFF button is pressed.  
• The driver's seat belt is not fastened.  
When Adaptive Cruise Control (ACC) with Low  
Speed Follow is in operation, the vehicle stops  
without depressing the brake pedal and Auto Idle  
Stop may activate. In such cases, the engine may  
restart if you change the shift position other than (D  
• The engine is not adequately warmed up or coolant temperature is high.  
• The transmission fluid temperature is low or high.  
• The vehicle comes to a stop again before the vehicle speed reaches 3 mph (5 km/  
h) after the engine starts.  
.
Pressing the ENGINE START/STOP button causes  
the engine to no longer restarts automatically. Follow  
the standard procedure to start the engine.  
2 Starting the Engine P. 491  
• The vehicle is stopped on a steep incline.  
• The transmission is in a position other than (D  
• The engine is started with the hood open.  
.
u Turn off the engine. Close the hood before you restart the engine to activate  
Auto Idle Stop.  
• The battery charge is low.  
• The internal temperature of the battery is 41°F (5°C) or less.  
• The climate control system is in use, and the outside temperature is below −4°F  
(−20°C) or over 104°F (40°C).  
• The climate control system is in use, and the temperature is set to Hi or Lo.  
•
is ON (indicator on).  
Models with DRIVE MODE switch  
• The drive mode is in the SPORT mode.  
514  
uuWhen DrivinguAuto Idle Stop  
■
Auto Idle Stop may not activate when:  
• The vehicle is stopped by braking suddenly.  
• The steering wheel is operated.  
• The vehicle is repeatedly accelerated and decelerated at a low speed.  
• The fan speed is high.  
• The climate control system is in use, and there is a significant difference between  
the set temperature and the actual interior temperature.  
• The climate control system is in use, and humidity in the interior is high.  
• Altitude is high.  
Continued  
515  
uuWhen DrivinguAuto Idle Stop  
1The Engine Automatically Restarts When:  
The Engine Automatically Restarts When:  
■
• The brake pedal is released (without the automatic brake hold system activated).  
If you are using an electronic device during Auto Idle  
Stop, the device may temporarily be turned off when  
the engine restarts.  
• The accelerator pedal is depressed (with the automatic brake hold system  
activated).  
2 Automatic Brake Hold P. 660  
• When the transmission is put into (P from (D or (N on a slope.  
1The engine restarts even if the brake pedal is depressed*1 when:  
■
The engine restarts even if the brake pedal is depressed*1 when:  
• The Auto Idle Stop OFF button is pressed.  
*1: With the automatic brake hold system activated,  
you can release the brake pedal while Auto Idle Stop  
is in operation.  
• The steering wheel is operated.  
• The transmission is put into (R .  
(S*, or (L*, or when it is set from (N to (D  
,
u If you put the transmission into (P after the Auto Idle Stop activates, the Auto  
Idle Stop continues to operate. In this case, the engine restarts when you  
depress the brake pedal.  
If the automatic brake hold system has been turned  
off, or if there is a problem with the system, the  
engine will restart automatically when you release  
the brake pedal.  
• The pressure on the brake pedal is reduced and the vehicle starts moving while  
stopped on an incline.  
2 Automatic Brake Hold P. 660  
• The pressure on the brake pedal is repeatedly applied and released slightly during  
a stop.  
• The battery charge becomes low.  
• The accelerator pedal is depressed.  
• The driver's seat belt is unlatched.  
•
is ON (indicator on).  
• The climate control system is in use, and the difference between the set  
temperature and actual interior temperature becomes significant.  
• The climate control system is being used to dehumidify the interior.  
• The vehicle ahead of you starts again when your vehicle stops automatically with  
Adaptive Cruise Control (ACC) with Low Speed Follow.  
Models with DRIVE MODE switch  
• The SPORT mode is selected by using the DRIVE MODE switch.  
* Not available on all models  
516  
uuWhen DrivinguAuto Idle Stop  
Starting Assist Brake Function  
■
Briefly keeps the brake applied after releasing the brake pedal to restart the engine.  
This can keep your vehicle from unexpectedly moving while on an incline.  
517  
uuWhen DrivinguAuto Idle Stop  
Manual transmission models without Rev Match System  
Auto Idle Stop  
To help maximize fuel economy, the engine automatically stops when the vehicle  
comes to a stop, depending on environmental and vehicle operating conditions. The  
indicator (green) comes on at this time.  
The environmental and vehicle conditions that  
impact Auto Idle Stop system operation are  
varied.  
1Auto Idle Stop  
The 12-volt battery installed in this vehicle is  
specifically designed for a model with Auto Idle Stop.  
Using a 12-volt battery other than this specified type  
may shorten the 12-volt battery life, and prevent  
Auto Idle Stop from activating. If you need to replace  
the 12-volt battery, make sure to select the specified  
type. Ask a dealer for more details.  
2 Auto Idle Stop Activates When: P. 520  
2 Auto Idle Stop may not activate when:  
P. 521  
The duration of the Auto Idle Stop operation:  
•
Increase in the ECON mode, compared to when  
the ECON mode is off, with climate control in use.  
2 ECON Button* P. 511  
The engine then restarts once the vehicle is  
about to move again when you depress the  
Auto Idle Stop  
Indicator (Green)  
clutch pedal, and the indicator (green) goes  
off.  
2 The Engine Automatically Restarts When:  
P. 522  
If the driver's door is opened while the  
indicator (green) comes on, a buzzer sounds  
to notify you that the Auto Idle Stop function  
is in operation.  
A message associated with Auto Idle Stop  
appears on the driver information interface.  
* Not available on all models  
518  
uuWhen DrivinguAuto Idle Stop  
The Auto Idle Stop suspend indicator comes  
on and a message appears on the gauge  
when the Auto Idle Stop system cannot be  
activated.  
2 Indicators P. 96  
2 Auto Idle Stop System ON/OFF P. 519  
Auto Idle Stop  
Suspend Indicator  
1Auto Idle Stop System ON/OFF  
Auto Idle Stop System ON/OFF  
■
If you turn off the Auto Idle Stop system while it is  
activated, the engine will restart.  
To turn the Auto Idle Stop system off, press  
Auto Idle Stop OFF  
Indicator  
this button. The Auto Idle Stop system stops.  
u Auto Idle Stop system will stop, the  
indicator will come on and a message  
appears on the gauge.  
If you hold the Auto Idle Stop OFF button, you can  
disable idle stop messages.  
2 Indicators P. 96  
The Auto Idle Stop system is turned on every  
time you start the engine, even if you turned it  
off the last time you drove the vehicle.  
Auto Idle Stop  
OFF Button  
Continued  
519  
uuWhen DrivinguAuto Idle Stop  
1Auto Idle Stop Activates When:  
Auto Idle Stop Activates When:  
■
After the vehicle moves forward, stopping with the brake, the clutch pedal fully  
depressed, the shift lever in (N, and then the clutch pedal is released.  
Do not open the hood while the Auto Idle Stop  
function is activated. If the hood is opened, the  
engine will not restart automatically.  
In this case, restart the engine with the ENGINE  
START/STOP button.  
■
Auto Idle Stop does not activate when:  
• The Auto Idle Stop OFF button is pressed.  
• The driver's seat belt is not fastened.  
2 Starting the Engine P. 491  
Pressing the ENGINE START/STOP button causes  
the engine to no longer restarts automatically. Follow  
the standard procedure to start the engine.  
2 Starting the Engine P. 491  
• The engine is not adequately warmed up or coolant temperature is high.  
• The vehicle comes to a stop again before the vehicle speed reaches 2 mph  
(3 km/h) after the engine starts.  
• The engine is started with the hood open.  
u Turn off the engine. Close the hood before you restart the engine to activate  
Auto Idle Stop.  
• The battery charge is low.  
• The internal temperature of the battery is 41°F (5°C) or less.  
• The shift lever is in any position except (N  
.
• The climate control system is in use, and the outside temperature is below −4°F  
(−20°C) or over 104°F (40°C).  
• The climate control system is in use, and the temperature is set to Hi or Lo.  
•
is ON (indicator on).  
520  
uuWhen DrivinguAuto Idle Stop  
■
Auto Idle Stop may not activate when:  
• The steering wheel is operated.  
• The fan speed is high.  
• The climate control system is in use, and there is a significant difference between  
the set temperature and the actual interior temperature.  
• The climate control system is in use, and humidity in the interior is high.  
• Altitude is high.  
Continued  
521  
uuWhen DrivinguAuto Idle Stop  
1The Engine Automatically Restarts When:  
The Engine Automatically Restarts When:  
■
The clutch pedal is depressed.  
If you are using an electronic device during Auto Idle  
Stop, the device may temporarily be turned off when  
the engine restarts.  
■
The engine automatically restarts even if the clutch pedal is not depressed  
with the transmission in (N when:  
The engine does not restart automatically when there  
is a problem in the system. Follow the normal  
procedure to start the engine.  
• The Auto Idle Stop OFF button is pressed.  
• The pressure on the brake pedal is reduced and the vehicle starts moving while  
stopped on an incline.  
2 Starting the Engine P. 491  
• The steering wheel is operated.  
The engine does not restart automatically when:  
• The pressure on the brake pedal is repeatedly applied and released slightly during  
a stop.  
• The battery charge becomes low.  
•
•
The driver's seat belt is unlatched.  
The transmission is put into a position other than  
(N. Put the transmission into (N to restart the  
engine.  
•
is ON (indicator on).  
• The climate control system is in use, and the difference between the set  
temperature and actual interior temperature becomes significant.  
• The climate control system is being used to dehumidify the interior.  
NOTICE  
Auto Idle Stop system also comes with stall recovery.  
If you fully depress the clutch pedal after stalling the  
engine, the engine automatically restarts.  
2 Starting to Drive P. 496  
When the system stops operating, follow the normal  
procedure to start the engine.  
2 Starting the Engine P. 491  
522  
uuWhen DrivinguDrive Mode Switch*  
Drive Mode Switch*  
1Drive Mode Switch*  
The mode may not be able to be changed when:  
Models with paddle shifter  
You can choose between three modes, SPORT mode, NORMAL mode and ECON  
mode by using the DRIVE MODE switch.  
The current mode is displayed on the gauge, and each mode will appear differently.  
•
•
•
The vehicle is turning.  
The VSA® system is activating.  
There is a problem with the engine, the  
transmission, the VSA®, and the EPS.  
SPORT  
Mode  
NORMAL  
Mode  
ECON  
Mode  
DRIVE MODE Switch  
* Not available on all models  
Continued  
523  
uuWhen DrivinguDrive Mode Switch*  
1SPORT Mode  
SPORT Mode  
■
While in SPORT mode, the Auto Idle Stop System will  
stay disabled regardless of the Auto Idle Stop OFF  
button.  
Enhances responsiveness to the driver's input.  
2 Auto Idle Stop P. 512  
NORMAL Mode  
■
Optimizes the balance between operability  
and comfort.  
524  
uuWhen DrivinguDrive Mode Switch*  
1ECON Mode  
ECON Mode  
■
While in ECON mode, the climate control system will  
be less effective and the vehicle slower to accelerate.  
Facilitates fuel-efficient driving.  
Continued  
525  
uuWhen DrivinguDrive Mode Switch*  
■
Next start-up mode  
The mode for the next start-up is saved according to the following chart.  
Last Drive Mode  
ECON Mode  
Next Drive Mode  
ECON Mode  
NORMAL Mode  
SPORT Mode  
NORMAL Mode  
NORMAL Mode  
526  
uuWhen DrivinguDrive Mode Switch*  
Drive Mode Switch*  
1Drive Mode Switch*  
The mode may not be able to be changed when:  
Manual transmission models without Auto Idle Stop  
You can choose between four modes, +R mode, SPORT mode, COMFORT mode  
and INDIVIDUAL mode by using the DRIVE MODE switch or the +R button.  
The current mode is displayed on the gauge, and each mode will appear differently.  
•
•
•
The vehicle is turning.  
The VSA® system is activating.  
There is a problem with the adaptive damper  
system, the engine, the VSA®, and the EPS.  
* Not available on all models  
Continued  
527  
uuWhen DrivinguDrive Mode Switch*  
Selecting the Drive Mode  
■
Audio/Information Screen  
+R Mode  
Changing modes  
by DRIVE MODE  
switch or +R  
button alters the  
screen on the  
gauge.  
INDIVIDUAL Settings Screen  
INDIVIDUAL Mode  
SPORT Mode  
Press the  
or  
button*1  
Press the DRIVE MODE switch up and hold or select  
Customize  
+R button  
2 Customizing the INDIVIDUAL Settings P. 532  
COMFORT Mode  
Press the DRIVE MODE switch up or down  
Press the +R button  
DRIVE MODE  
Switch  
*1: The display returns to audio/information screen a few seconds after  
pressing the +R button or the DRIVE MODE switch up or down.  
528  
uuWhen DrivinguDrive Mode Switch*  
COMFORT Mode  
■
■
Enhances driver comfort.  
SPORT Mode  
Enhances responsiveness to the driver's input.  
Continued  
529  
uuWhen DrivinguDrive Mode Switch*  
INDIVIDUAL Mode  
■
Customize each category to suit the driver’s  
preference.  
2 Customizing the INDIVIDUAL Settings  
P. 532  
+R Mode  
■
Maximizes responsiveness to the driver's  
input.  
Several VSA® features can be turned off  
entirely.  
2 When in +R Drive mode P. 535  
530  
uuWhen DrivinguDrive Mode Switch*  
■
Next start-up mode  
The mode for the next start-up is saved according to the following chart.  
Last Drive Mode  
COMFORT  
Next Drive Mode  
COMFORT  
INDIVIDUAL  
SPORT  
+R  
INDIVIDUAL  
SPORT  
If the +R mode is last used before you  
turn the power mode to OFF, the mode  
before selecting the +R mode is selected  
next time you turn the power mode to  
ON.  
Continued  
531  
uuWhen DrivinguDrive Mode Switch*  
Customizing the INDIVIDUAL Settings  
■
1. Select INDIVIDUAL mode.  
2. Press the DRIVE MODE switch up and hold  
or select Customize to open the  
INDIVIDUAL Settings.  
u You can also select from customized  
features on the audio/information  
screen.  
2 Selecting the Drive Mode P. 528  
2 Customized Features P. 382  
3. Select the setting category.  
4. Select the desired setting.  
532  
uuWhen DrivinguVehicle Stability AssistTM (VSA®), aka Electronic Stability Control (ESC), System  
Vehicle Stability AssistTM (VSA®), aka Electronic  
Stability Control (ESC), System  
1Vehicle Stability AssistTM (VSA®), aka Electronic Stability Control  
VSA® helps stabilize the vehicle during cornering if the vehicle turns more or less  
than what was intended. It also assists in maintaining traction on slippery surfaces.  
It does so by regulating engine output and selectively applying the brakes.  
(ESC), System  
The VSA® may not function properly if tire type and  
size are mixed. Make sure to use the same size and  
type of tire, and the air pressures as specified.  
VSA® Operation  
■
When VSA® activates, you may notice that the  
VSA® System Indicator  
engine does not respond to the accelerator.  
When the VSA system indicator comes on and stays on  
®
while driving, there may be a problem with the system.  
While this may not interfere with normal driving, have  
your vehicle checked by a dealer immediately.  
You may also notice some noise from the  
hydraulic brake system. You will also see the  
indicator blink.  
*3  
*1  
The Vehicle Stability AssistTM (VSA®) system, Vehicle  
Stability AssistTM (VSA®) OFF*, Adaptive Cruise Control  
(ACC)*, Adaptive Cruise Control (ACC) with Low  
Speed Follow*, low tire pressure/TPMS* and safety  
support indicators may come on in amber along with a  
message in the gauge when you set the power mode  
to ON after reconnecting the battery.  
*2  
Drive a short distance at more than 12 mph (20 km/h).  
Each indicator should go off. If any do not, have your  
vehicle checked by a dealer.  
VSA® cannot enhance stability in all driving situations  
and does not control the entire braking system. You  
still need to drive and corner at speeds appropriate  
for the conditions and always leave a sufficient  
margin of safety.  
The main function of the VSA® system is generally  
known as Electronic Stability Control (ESC). The  
system also includes a traction control function.  
*1: Models with A-type meter  
*2: Models with B-type meter  
*3: When using the +R gauge*  
* Not available on all models  
Continued  
533  
uuWhen DrivinguVehicle Stability AssistTM (VSA®), aka Electronic Stability Control (ESC), System  
1Vehicle Stability AssistTM (VSA®), aka Electronic Stability Control  
VSA® On and Off  
■
(ESC), System  
This button is on the driver side control panel.  
To partially disable VSA® functionality/  
features, press and hold it until you hear a  
beep.  
VSA® OFF Indicator  
In certain unusual conditions when your vehicle gets  
stuck in shallow mud or fresh snow, it may be easier  
to free it with the VSA® temporarily switched off.  
*3  
*1  
*2  
When the  
button is pressed, the traction control  
function becomes less effective. This allows for the  
wheels to spin more freely at low speed. You should  
only attempt to free your vehicle with the VSA® off if  
you are not able to free it when the VSA® is on.  
Your vehicle will have normal braking and  
cornering ability, but traction control function  
will be less effective.  
To restore VSA® functionality/features, press  
Immediately after freeing your vehicle, be sure to  
switch VSA® on again. We do not recommend driving  
your vehicle with the VSA® system switched off.  
the  
beep.  
(VSA® OFF) button until you hear a  
You may hear a motor sound coming from the  
engine compartment while system checks are being  
performed immediately after starting the engine or  
while driving. This is normal.  
VSA® is turned on every time you start the  
engine, even if you turned it off the last time  
you drove the vehicle.  
*1: Models with A-type meter  
*2: Models with B-type meter  
*3: When using the +R gauge*  
* Not available on all models  
534  
uuWhen DrivinguVehicle Stability AssistTM (VSA®), aka Electronic Stability Control (ESC), System  
Models without Auto Idle Stop  
■
When in +R Drive mode  
1When in +R Drive mode  
To completely disable VSA®, press and hold  
the VSA® OFF button until you hear a single  
beep, then later two more beeps.  
u Vehicle stability assist system fully  
OFF message appears on the driver  
information interface.  
In OFF mode, your vehicle will have normal braking  
and cornering ability, but it will not have VSA®  
traction and stability enhancement.  
When the VSA® system is off, the traction control  
system is also off.  
We do not recommend driving your vehicle with the  
VSA® and traction control system switched off.  
To resume VSA® full function, press the VSA®  
OFF button until a single beep is heard.  
When you completely disable VSA®, you cannot use  
Adaptive Cruise Control (ACC) or the Lane Keeping  
Assist System (LKAS).  
If VSA® OFF mode is selected, and drive mode  
is changed to a mode other than +R, VSA® full  
function will resume, and the VSA® OFF  
indicator will goes off.  
Low Speed Braking Control*, Road Departure  
Mitigation System and Collision Mitigation Braking  
SystemTM (CMBSTM) do not function while VSA® is  
completely disabled.  
Some of the VSA® features cannot be completely  
turned off while driving.  
* Not available on all models  
535  
uuWhen DrivinguAgile Handling Assist  
Agile Handling Assist  
Lightly brakes the front wheels, as needed, when you turn the steering wheel, and  
helps support the vehicle's stability and performance during cornering.  
1Agile Handling Assist  
The agile handling assist cannot enhance stability in  
all driving situations. You still need to drive and  
corner at speeds appropriate for the conditions and  
always leave a sufficient margin of safety.  
When the VSA® system indicator comes on and stays  
on while driving, the agile handling assist does not  
activate.  
You may hear a sound coming from the engine  
compartment while the agile handling assist is  
activated. This is normal.  
536  
uuWhen DrivinguLimited Slip Differential (LSD)*  
Limited Slip Differential (LSD)*  
1Limited Slip Differential (LSD)*  
Limited Slip Differential (LSD)  
■
NOTICE  
LSD (limited slip differential) is a type of differential that delivers extra torque to the  
wheel or the wheels with the most traction to minimize wheel slip and maintain  
control of the vehicle.  
Make sure both front tires of your vehicle are of the  
same brand and specified size, and have equal wear.  
Otherwise, the LSD may not function properly.  
* Not available on all models  
537  
uuWhen DrivinguTire Pressure Monitoring System (TPMS)*  
Tire Pressure Monitoring System (TPMS)*  
1Tire Pressure Monitoring System (TPMS)*  
Instead of directly measuring the pressure in each tire, the TPMS on this vehicle  
monitors and compares the rolling radius and rotational characteristics of each  
wheel and tire while you are driving to determine if one or more tires are  
significantly under-inflated.  
The system does not monitor the tires when driving  
at low speed.  
Conditions such as low ambient temperature and  
altitude change directly affect tire pressure and can  
trigger the low tire pressure/TPMS indicator to come on.  
This will cause the low tire pressure/TPMS  
indicator to come on and a message to appear  
on the gauge.  
Models with A-type meter  
Low Tire Pressure/  
TPMS Indicator  
Tire pressure checked and inflated in:  
•
Warm weather can become under-inflated in  
colder weather.  
•
Cold weather can become overinflated in warmer  
weather.  
The low tire pressure/TPMS indicator will not come  
on as a result of overinflation.  
Models with B-type meter  
The TPMS may not function properly if tire type and  
size are mixed. Make sure to use the same size and  
type of tire.  
2 Checking and Maintaining Tires P. 734  
The low tire pressure/TPMS indicator may come on  
with a delay or may not come on at all when:  
Low Tire Pressure/TPMS Indicator  
•
You rapidly accelerate, decelerate, or turn the  
steering wheel.  
•
•
You drive on snowy or slippery roads.  
Tire chains* are used.  
The low tire pressure/TPMS indicator may come on  
under the following conditions:  
•
•
A compact spare tire* is used.  
Tire chains* are used.  
* Not available on all models  
538  
uuWhen DrivinguTire Pressure Monitoring System (TPMS)*  
1Tire Pressure Monitoring System (TPMS)*  
The Vehicle Stability AssistTM (VSA®) system, Vehicle  
Stability AssistTM (VSA®) OFF*, Adaptive Cruise  
Control (ACC)*, Adaptive Cruise Control (ACC) with  
Low Speed Follow*, low tire pressure/TPMS and  
safety support indicators may come on in amber  
along with a message in the gauge when you set the  
power mode to ON after reconnecting the battery.  
Drive a short distance at more than 12 mph (20 km/h).  
Each indicator should go off. If any do not, have your  
vehicle checked by a dealer.  
1TPMS Calibration  
TPMS Calibration  
■
TPMS cannot be calibrated if a compact spare tire* is  
installed.  
The calibration process requires approximately 30  
minutes of cumulative driving at speeds between  
31-62 mph (50-100 km/h).  
During this period, if power mode is set to ON and  
the vehicle is not moved within 45 seconds, you may  
notice the low tire pressure/TPMS indicator comes on  
briefly. This is normal and indicates that the  
calibration process is not yet complete.  
You must start TPMS calibration every time you:  
• Adjust the pressure in one or more tires.  
• Rotate the tires.  
• Replace one or more tires.  
Before calibrating the TPMS:  
• Set the cold tire pressure in all four tires.  
2 Checking Tires P. 734  
If the tire chains* are installed, remove them before  
calibrating the TPMS.  
Make sure:  
• The vehicle is at a complete stop.  
• The power mode is in ON.  
If the low tire pressure/TPMS indicator comes on even  
when the properly inflated specified regular tires are  
installed, have your vehicle checked by a dealer.  
Continuously variable transmission models  
• The transmission is in (P  
.
We recommend that the tires be replaced with the  
same brand, model, and size as the originals. Ask a  
dealer for details.  
Manual transmission models  
• The shift lever is in (N  
.
* Not available on all models  
Continued  
539  
uuWhen DrivinguTire Pressure Monitoring System (TPMS)*  
Models with 7-in. Color Touchscreen  
You can calibrate the system from the settings  
on the driver information interface.  
1. Press the  
(home) button, to select  
Settings, then press the left selector wheel.  
u Vehicle settings appears on the display.  
2. Roll the left selector wheel.  
u TPMS calibration appears on the  
display.  
540  
uuWhen DrivinguTire Pressure Monitoring System (TPMS)*  
3. Press the left selector wheel.  
u The display switches to the  
customization setup screen, where you  
can select Cancel or Calibrate.  
4. Roll the left selector wheel and select  
Calibrate, then press the left selector  
wheel.  
u Calibration started screen appears,  
then the display returns to the  
customization menu screen.  
• If the Calibration failed to start message  
appears, repeat step 4.  
• The calibration process finishes  
automatically.  
Continued  
541  
uuWhen DrivinguTire Pressure Monitoring System (TPMS)*  
Models with 9-in. Color Touchscreen  
You can calibrate the system from the  
customized feature on the audio/information  
screen.  
1. Set the power mode to ON.  
2. Press the  
button.  
3. Select Vehicle Settings.  
4. Select TPMS Calibration.  
5. Select Calibrate or Cancel.  
• If the Calibration Failed To Start.  
message appears, repeat step 5.  
• The calibration process finishes  
automatically.  
542  
uuWhen DrivinguTire Pressure Monitoring System (TPMS) - Required Federal Explanation*  
Tire Pressure Monitoring System (TPMS) - Required  
Federal Explanation*  
Each tire, including the spare (if provided), should be checked  
monthly when cold and inflated to the inflation pressure  
recommended by the vehicle manufacturer on the vehicle placard  
or tire inflation pressure label.  
(If your vehicle has tires of a different size than the size indicated  
on the vehicle placard or tire inflation pressure label, you should  
determine the proper tire inflation pressure for those tires.)  
As an added safety feature, your vehicle has been equipped with  
a tire pressure monitoring system (TPMS) that illuminates a low  
tire pressure telltale  
when one or more of your tires is significantly under-inflated.  
Accordingly, when the low tire pressure telltale illuminates, you  
should stop and check your tires as soon as possible, and inflate  
them to the proper pressure.  
Driving on a significantly under-inflated tire causes the tire to  
overheat and can lead to tire failure. Under-inflation also reduces  
fuel efficiency and tire tread life, and may affect the vehicle's  
handling and stopping ability.  
* Not available on all models  
Continued  
543  
uuWhen DrivinguTire Pressure Monitoring System (TPMS) - Required Federal Explanation*  
Please note that the TPMS is not a substitute for proper tire  
maintenance, and it is the driver's responsibility to maintain  
correct tire pressure, even if under-inflation has not reached the  
level to trigger illumination of the TPMS low tire pressure telltale.  
Your vehicle has also been equipped with a TPMS malfunction  
indicator to indicate when the system is not operating properly.  
The TPMS malfunction indicator is combined with the low tire  
pressure telltale. When the system detects a malfunction, the  
telltale will flash for approximately one minute and then remain  
continuously illuminated. This sequence will continue upon  
subsequent vehicle start-ups as long as the malfunction exists.  
When the malfunction indicator is illuminated, the system may  
not be able to detect or signal low tire pressure as intended.  
TPMS malfunctions may occur for a variety of reasons, including  
the installation of replacement or alternate tires or wheels on the  
vehicle that prevent the TPMS from functioning properly.  
Always check the TPMS malfunction telltale after replacing one or  
more tires or wheels on your vehicle to ensure that the  
replacement or alternate tires and wheels allow the TPMS to  
continue to function properly.  
544  
uuWhen DrivinguBlind Spot Information System*  
Blind Spot Information System*  
1Blind Spot Information System*  
When the system detects vehicles approaching from behind in adjacent lanes, the  
appropriate indicator comes on, providing assistance when you change lanes.  
Important Safety Reminder  
Like all assistance systems, the blind spot information  
system has limitations. Always look in your mirrors, to  
either side of your vehicle, and behind you for other  
vehicles before changing lanes. Overreliance on the  
blind spot information system may result in a  
collision.  
How the System works  
■
The system activates when your vehicle is moving forward at about 20 mph (32 km/h)  
or above.  
: Alert Zone 1  
: Alert Zone 2  
Radar Sensors: underneath the  
rear bumper corners  
Have your vehicle checked by a dealer in the  
following situations:  
•
•
•
The rear bumper or area around the radar sensors  
is strongly impacted.  
The indicator does not come on even if a vehicle in  
the alert zone should have been detected.  
The rear bumper or any system components need  
to be repaired.  
A
If the rear bumper or any system components are  
repaired, the system will revert to alert zone 1 only  
until it is able to adapt and expand to alert zone 1  
and 2.  
B
C
Alert zone range  
A: Approx. 1.6 ~ 10 feet (0.5 ~ 3 meters) from vehicle side.  
B: Approx. 10 feet (3 meters) from rear bumper.  
C: Approx. 10 ~ 82 feet (3 ~ 25 meters) behind from rear bumper. (The faster the  
approaching vehicle, the further away it will be detected.)  
The initially set alert zone is alert zone 1. Over time, after the vehicle has been driven  
on straight roads with traffic and roadside objects, the system will adapt and expand  
the alert zone (alert zone 1 and 2).  
* Not available on all models  
Continued  
545  
uuWhen DrivinguBlind Spot Information System*  
1Blind Spot Information System*  
■
When the system detects a vehicle  
Blind spot information system alert indicator:  
For proper blind spot information system operation:  
•
Comes On  
Located on the outside rearview mirror on  
both sides.  
Always keep the rear bumper and area around the  
radar sensors clean.  
•
Do not cover the rear bumper corner area with  
labels or stickers of any kind.  
Comes on when:  
Blinks  
• A vehicle approaches you from behind to  
overtake you at a speed difference of no  
more than about 31 mph (50 km/h).  
• You pass a vehicle at a speed difference of  
no more than about 12 mph (20 km/h).  
The system is for your convenience only. Even if an  
object is within the alert zone, the following  
situations may occur:  
•
The blind spot information system alert indicator  
does not come on and the message Blind spot  
information system not available appears on  
the driver information interface.  
Blinks and a beeper sounds when:  
You use the turn signal lever to signal a turn in  
the direction of the detected vehicle while the  
blind spot information system alert indicator is  
on.  
•
The blind spot information system alert indicator  
may come on even with the message displayed.  
The Vehicle Stability AssistTM (VSA®) system, Vehicle  
Stability AssistTM (VSA®) OFF*, Adaptive Cruise  
Control (ACC)*, Adaptive Cruise Control (ACC) with  
Low Speed Follow*, low tire pressure/TPMS* and  
safety support indicators may come on in amber  
along with a message in the gauge when you set the  
power mode to ON after reconnecting the battery.  
Drive a short distance at more than 12 mph  
(20 km/h).  
u The beeper sounds three times.  
Each indicator should go off. If any do not, have your  
vehicle checked by a dealer.  
* Not available on all models  
546  
uuWhen DrivinguBlind Spot Information System*  
1Blind Spot Information System*  
Blind Spot Information System On and Off  
■
You can also select safety support content from the  
driver information interface.  
When you turn the blind spot information  
system on and off, do the following.  
1. Press the safety support switch.  
Models with A-type meter  
2 Driver Information Interface (A-type  
Meter) P. 125  
Left Selector  
Wheel  
2 Driver Information Interface Right Side  
Area (B-type-Meter) P. 154  
Models with A-type meter  
2. Roll the left selector wheel to the  
and push it.  
symbol  
You can change the settings for the blind spot  
information system.  
Models with B-type meter  
2 Settings P. 138  
2 Customized Features P. 390  
2. Roll the right selector wheel to the  
symbol and push it.  
u A message appears on the driver  
Safety Support Switch  
information interface when the system  
turns on or off.  
u A check mark appears in the box and the  
Models with B-type meter  
color of the  
symbol changes to green  
when the system is on. The check mark  
disappears and the color of the  
symbol changes to gray when the system  
is off.  
Right  
Selector  
Wheel  
The blind spot information system will stay on  
the previously selected on (checked) or off  
(unchecked) setting each time you start the  
engine.  
Safety Support Switch  
* Not available on all models  
Continued  
547  
uuWhen DrivinguBlind Spot Information System*  
Blind Spot Information System Conditions and Limitations  
■
The blind spot information system alert indicator may not come on under the  
following conditions:  
• There is a large speed difference between your vehicle and the vehicle in the  
adjacent lane.  
• A vehicle is parked in a side lane.  
• An object not detected by the radar sensors approaches or passes your vehicle.  
• The vehicle driving in the adjacent lane is a motorcycle or other small vehicle.  
The blind spot information system may not operate correctly under the following  
conditions:  
• Making a turn at an intersection.  
• Objects (guard rails, poles, trees, etc.) are detected.  
• An object that does not reflect radio waves well or a motorcycle, is in the alert  
zone.  
• Driving on a curved road.  
• A vehicle is moving from a far lane to the adjacent lane.  
• The system picks up signal interference such as other radar sensors from another  
vehicle or strong radio wave transmitted from a facility nearby.  
• The rear bumper or the area around the radar sensors is covered by dirt, mud,  
snow, ice, etc.  
• The rear bumper or the area around the radar sensors has been damaged or  
deformed.  
• In bad weather (heavy rain, snow, and fog).  
• Making a short turn or driving on a bumpy road that slightly tilts the vehicle.  
• An object such as a bicycle rack is attached to the rear of the vehicle.  
548  

Related Topics

Driving
Before Driving Towing a Trailer Honda Sensing? Braking Parking Your Vehicle Multi-View Rear Camera Refueling Fuel Economy and CO2 Emissions Turbo Engine Vehicle*

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot