2021-2026 Honda Jazz 4 Door Controls -> Operating the Switches Around the Steering Wheel User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Controls -> Operating the Switches Around the Steering Wheel for Your Honda Jazz 4 Door Fourth Generation (2021-2026)

186
Controls
Operating the Switches Around the Steering Wheel
POWER Button
If you carry the keyless remote and press the
POWER button without depressing the brake
pedal, the power mode will change in this
order: VEHICLE OFFACCESSORYON
VEHICLE OFF.
VEHICLE OFF:
Vehicle power is turned OFF.
ACCESSORY:
The audio system and some accessories can be
used.
ON:
All accessories can be used.
■
Changing the Power Mode
1POWER Button
If the keyless remote is set in a storage box or another
place where its signal can be interrupted, the power
mode may not change.
When the power mode is set to ON, the power mode
will change to ACCESSORY if the POWER button is
pressed while the transmission is in a position other
than
(P .
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 186 ページ ２０２５年７月１８日　金曜日　午前９時２６分
187
uuOperating the Switches Around the Steering WheeluPOWER Button
Continued
Controls
If you leave the vehicle for 30 to 60 minutes with the transmission in (P and the
power mode in ACCESSORY, the vehicle automatically goes into the mode similar to
VEHICLE OFF (LOCK) to avoid draining the 12-volt battery.
When in this mode: The steering wheel does not lock. You cannot lock or unlock
doors with the remote transmitter or the keyless access system
*
. Press the POWER
button twice to switch the mode to VEHICLE OFF (LOCK).
If you open the driver’s door when the power mode is in ACCESSORY, a warning
beep sounds.
■
Automatic Power Off
■
Power Mode Reminder
* Not available on all models
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 187 ページ ２０２５年７月１８日　金曜日　午前９時２６分
uuOperating the Switches Around the Steering WheeluPOWER Button
188
Controls
When the power mode is set to any mode
other than OFF and you remove the keyless
remote from the vehicle and shut the door, an
alarm will sound. If the alarm continues to
sound, place the keyless remote in another
location.
■
When the power mode is in
ACCESSORY
The alarm will sound from outside the vehicle.
■
When the power mode is in ON
An alarm will sound both inside and outside
the vehicle. In addition, a warning indicator
will appear on the instrument panel.
■
Keyless Remote Reminder
1Keyless Remote Reminder
When the keyless remote is within the system’s
operational range, and the driver’s door is closed, the
warning function cancels.
If the keyless remote is taken out of the vehicle after
the power system has been turned on, you can no
longer change the POWER button mode or restart
the power system. Always make sure that the remote
is in your vehicle when you operate the POWER
button.
Removing the keyless remote from the vehicle
through a window does not activate the warning
buzzer.
Do not put the keyless remote on the dashboard or in
the glove box. It may cause the warning buzzer to
sound. Under some other conditions that can prevent
the vehicle from locating the remote, the warning
buzzer may also sound even if the remote is within
the system’s operational range.
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 188 ページ ２０２５年７月１８日　金曜日　午前９時２６分
189
uuOperating the Switches Around the Steering WheeluLights
Continued
Controls
Lights
The lights will turn on automatically depending on the ambient brightness. They can
also be switched on and off manually.
The exterior lights will switch on automatically
when the light switch is set to AUTO while
the power mode is in ON.
■
Manual operation
Headlights/position lights:
Turn the light switch to .
Position lights:
Turn the light switch to .
Headlight/position lights off:
Turn the light switch to OFF and release it while the shift position is in
(P and the
parking brake is applied.
u The lights will come back on automatically when:
• The light switch is turned to OFF again and released.
• The shift position is changed out of
(P and the parking brake is released.
■
Headlights/Position Lights
1Lights
When the lights are on, the lights on indicator in the
instrument panel will be on.
2 Lights On Indicator P. 118
The headlights are suitable for left hand drive and
right hand drive, without the need to make any
adjustments or masking, as per UN-Regulation No.48
Dover Regulation.
1Headlights/Position Lights
When the position lights are on, the tail and rear
licence plate lights will also switch on.
When the light switch is turned to or and
the power is turned to OFF, a beeper sounds when
the driver’s door is opened.
When the light switch is turned to AUTO and the
ambient light levels are low, the headlights and
position lights will switch on if you unlock a door.
They will switch off when the door is locked.
Do not leave the lights on when the power system is
off because it will cause the 12-volt battery to
discharge.
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 189 ページ ２０２５年７月１８日　金曜日　午前９時２６分
uuOperating the Switches Around the Steering WheeluLights
190
Controls
When the headlights are on, push the lever forward. Pull the lever back to return to
low beams.
■
Flashing the high beams
Pull the lever back to switch on the high
beams.
u Release the lever to return to low beams.
■
High Beams
1Headlights/Position Lights
The light sensor is in the location shown below. Do
not cover the light sensor.
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 190 ページ ２０２５年７月１８日　金曜日　午前９時２６分
Continued
191
uuOperating the Switches Around the Steering WheeluLights
Controls
The turn signals can be used when the power
mode is in ON.
■
: Turn signal
Push the lever up or down based on the
direction you want to turn, and the turn signal
will blink.
■
: One-touch turn signal
When you lightly push the lever up or down
and release it, the turn signal will blink 3
times.
u If you lightly push the lever in the
opposite direction while it is blinking, the
blinking will stop.
■
Turn Signals
1Turn Signals
The turn signal indicator on the instrument panel will
blink when the external turn signal blinks.
2 Indicators P. 106
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 191 ページ ２０２５年７月１８日　金曜日　午前９時２６分
uuOperating the Switches Around the Steering WheeluLights
192
Controls
The headlights automatically come on when the wipers are used several times within
a certain number of intervals with the headlight switch in AUTO.
The headlights automatically go off a few minutes later if the wipers are stopped.
The headlights, all other exterior lights, and the instrument panel lights turn off 15
seconds after you set the power mode to VEHICLE OFF, take the remote with you,
and close the driver’s door.
However, when the switch is in , the position lights remain on.
If you set the power mode to VEHICLE OFF with the headlight switch on, but do not
open the door, the lights turn off after 10 minutes (3 minutes, if the switch is in the
AUTO position).
The lights turn on again when you unlock or open the driver’s door. If you unlock
the door, but do not open it within 15 seconds, the lights go off. If you open the
driver’s door, you will hear a reminder chime alerting you that the lights are on.
■
Headlight Integration with Wipers
■
Automatic Lighting Off Feature
1Headlight Integration with Wipers
This feature activates while the headlights are off in
AUTO. The instrument panel brightness does not
change when the headlights come on.
At dark ambient light levels, the automatic lighting
control feature turns on the headlights, regardless of
the number of wiper sweeps.
You can turn the headlight integration with wipers
function on and off.
2 How to Customize the Vehicle Settings
P. 304
1Automatic Lighting Off Feature
You can change the headlight auto off timer setting.
2 How to Customize the Vehicle Settings
P. 304
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 192 ページ ２０２５年７月１８日　金曜日　午前９時２６分
193
uuOperating the Switches Around the Steering WheeluLights
Continued
Controls
The fog lights can be used when the power mode is in ON.
■
Front fog lights
*
Can be used when the position lights or the headlights are on.
■
Rear fog light
Can be used when the headlights or the front fog lights are on.
■
Front and rear fog light switch
*
To turn the front fog lights on:
Rotate the switch up from the OFF position to
the position. The indicator comes on.
To turn the front and rear fog lights on:
Rotate the switch one position up from the
position. The and indicators come on.
To turn the rear fog lights on:
Rotate the switch one position up from the
position and then rotate the switch one
position down from the position. The
indicator stays on.
To turn the rear fog light off, turn the
headlight switch to the OFF position.
■
Fog Lights
* Not available on all models
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 193 ページ ２０２５年７月１８日　金曜日　午前９時２６分
194
uuOperating the Switches Around the Steering WheeluLights
Controls
■
Rear fog light switch
*
To turn the rear fog lights on:
Rotate the switch to . The indicator
comes on.
* Not available on all models
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 194 ページ ２０２５年７月１８日　金曜日　午前９時２６分
195
uuOperating the Switches Around the Steering WheeluLights
Controls
The daytime running lights come on when the following conditions have been met:
• The power mode is in ON.
• The headlight switch is AUTO.
• The ambient light is bright.
While the vehicle is stopped, if you turn the light switch to OFF and release it, the
daytime running lights will turn off. When the shift position is changed out of
(P
and the parking brake is released, the lights will come on again. Otherwise, if the
light switch is once more turned to OFF, the lights will come on again.
■
Daytime Running Lights
1Daytime Running Lights
Daytime running lights and the position lights share
the same light source.
Daytime running lights are brighter than the position
lights.
The daytime running lights will not switch on if the
position lights have been turned on manually.
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 195 ページ ２０２５年７月１８日　金曜日　午前９時２６分
196
uuOperating the Switches Around the Steering WheeluHeadlight Adjuster
Controls
Headlight Adjuster
You can adjust the vertical angle of the low
beam headlights when the position lights or
headlights are on.
Turn the adjustment dial to select an
appropriate angle for the headlights.
The larger dial number indicates the lower
angle.
■
To select the adjusting dial position
Refer to the below table for the appropriate dial position for your vehicle's riding
and loading conditions.
Condition Dial position
A driver
0
A driver and a front passenger
Five persons in the front and rear seats 1
Five persons in the front and rear seats and luggage in
the luggage area, within the limit of maximum
permissible axle weight and maximum permissible
vehicle weight
2
A driver and luggage in the luggage area, within the
limits of maximum permissible axle weight and
maximum permissible vehicle weight
3
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 196 ページ ２０２５年７月１８日　金曜日　午前９時２６分
197
uuOperating the Switches Around the Steering WheeluAuto High-Beam
Continued
Controls
Auto High-Beam
The front wide view camera detects the light sources ahead of the vehicle such as
the lights of a preceding or oncoming vehicle, or street lights. When you are driving
at night, the system automatically switches the headlights between low beam and
high beam depending on the situation.
■
Activating the system
When all of the following conditions have been met, the auto high-beam indicator
comes on and automatically switches between the high beam and low beam,
depending on the situation.
• The power mode is in ON.
• The light switch is in AUTO.
• The lever is in the low beam position.
• The headlights have been automatically
activated.
• It is dark outside the vehicle.
If the auto high-beam indicator does not come on even when all the conditions have
been met, carry out either of the procedures below and the indicator will come on.
• Pull the lever towards you and release it.
• Turn the light switch to then turn the light switch to AUTO.
■
How to Use the Auto High-Beam
1Auto High-Beam
The auto high-beam system does not always operate
in every situation. This system is just for assisting the
driver. Always observe your surroundings and
manually switch the headlights between high beam
and low beam if necessary.
The range and the distance at which the camera can
recognise light sources varies depending on
conditions surrounding your vehicle.
Regarding the handling of the camera mounted to
the inside of the windscreen, refer to the following.
2 Front Wide View Camera P. 469
For the auto high-beam to work properly:
• Do not place an object that reflects light on the
dashboard.
• Keep the windscreen around the camera clean.
• When cleaning the windscreen, be careful not to
apply the windscreen cleanser to the camera lens.
• Do not attach an object, sticker, or film to the area
around the camera.
• Do not touch the camera lens.
If the camera receives a strong impact, or repairing of
the area near the camera is required, consult a dealer.
a
Auto High-Beam Indicator
b
Light Switch
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 197 ページ ２０２５年７月１８日　金曜日　午前９時２６分
uuOperating the Switches Around the Steering WheeluAuto High-Beam
198
Controls
■
Automatic switching between high-beam and low-beam
When the auto high-beam indicator comes on, the headlights switch between high
beam and low beam based on the following conditions.
High beam Low beam
All of the following conditions must
be met before the high beams turn
on.
●
Your vehicle speed is 40 km/h
(25 mph) or more.
●
There are no preceding or
oncoming vehicles with
headlights or taillights turned on.
●
There are few street lights on the
road ahead.
One of the following conditions
must be met before the low beams
turn on.
●
Your vehicle speed is 24 km/h
(15 mph) or less.
●
There is a preceding or oncoming
vehicle with headlights or
taillights turned on.
●
There are many street lights on
the road ahead.
1Automatic switching between high-beam and low-beam
In the following cases, the auto high-beam system
may not switch the headlights properly or the
switching timing may be changed. If the automatic
switching operation does not fit for your driving
habits, please switch the headlights manually.
• The brightness of the lights from the preceding or
oncoming vehicle is intense or poor.
• Visibility is poor due to the weather (rain, snow,
fog, windscreen frost, etc.).
• Surrounding light sources like street lights, electric
billboards and traffic lights are illuminating the
road ahead.
• The brightness level of the road ahead constantly
changes.
• The road is bumpy or has many curves.
• A vehicle suddenly appears in front of you, or a
vehicle in front of you is not in the preceding or
oncoming direction.
• Your vehicle is tilted with a heavy load in the rear.
• A traffic sign, mirror, or other reflective object
ahead is reflecting strong light towards the vehicle.
• The oncoming vehicle frequently disappears under
roadside trees or behind median barriers.
• The preceding or oncoming vehicle is a motorcycle,
bicycle, mobility scooter, or other small vehicle.
The auto high-beam system keeps the headlight low
beam on when:
• Windscreen wipers are operating at a high speed.
• The camera has detected a dense fog.
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 198 ページ ２０２５年７月１８日　金曜日　午前９時２６分
199
uuOperating the Switches Around the Steering WheeluAuto High-Beam
Controls
■
Manual switching between high-beam and low-beam
If you want to manually switch the headlights between high beam and low beam,
follow either of the procedures below. Note that when you do this, the auto high-
beam indicator will turn off and the auto high-beam will be deactivated.
Using the lever:
Pull the lever towards you for flashing the high beams then release it.
u To reactivate the auto high-beam, follow either of the procedures below and
the auto high-beam indicator will come on.
• Pull the lever towards you and release it.
•
Turn the light switch to and then to
AUTO
when the lever is in the low beam position.
Using the light switch:
Turn the light switch to .
u To reactivate the auto high-beam, turn the light switch to AUTO when the
lever is in the low beam position, and the auto high-beam indicator will come
on.
1Auto High-Beam
How to turn off the Auto High-Beam System
You can change the auto high-beam system on and
off.
2 How to Customize the Vehicle Settings
P. 304
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 199 ページ ２０２５年７月１８日　金曜日　午前９時２６分
200
uuOperating the Switches Around the Steering WheeluWipers and Washers
Controls
Wipers and Washers
The windscreen wipers and washers can be
used when the power mode is in ON.
■
MIST
The wipers run at high speed until you release
the lever.
■
Wiper switch (OFF, AUTO, LO, HI)
Move the lever up or down to change the
wiper settings.
■
Washer
Sprays while you pull the lever towards you.
When you release the lever for more than one
second, the spray stops, the wipers sweep two
or three more times to clear the windscreen,
and then stop.
■
Windscreen Wipers/Washers
1Wipers and Washers
NOTICE
Do not use the wipers when the windscreen is dry.
The windscreen will get scratched, or the rubber
blades will get damaged.
The wiper motor may stop motor operation
temporarily to prevent an overload. Wiper operation
will return to normal within a few minutes.
NOTICE
Turn the washers off if no washer fluid comes out.
The pump may get damaged.
NOTICE
In cold weather, the blades may freeze to the
windscreen.
Operating the wipers in this condition may damage
the wipers. Use the demister to warm the
windscreen, then turn the wipers on.
If the wipers stop operating due to an obstacle such
as the buildup of snow, park the vehicle in a safe
place. Rotate the wiper switch to OFF, set the power
mode to ACCESSORY or VEHICLE OFF, then remove
the obstacle.
a
MIST
b
OFF
c
AUTO
d
LO: Low speed wipe
e
HI: High speed wipe
f
Washer
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 200 ページ ２０２５年７月１８日　金曜日　午前９時２６分
Continued
201
uuOperating the Switches Around the Steering WheeluWipers and Washers
Controls
When you push the lever down to AUTO, the
windscreen wipers sweep once, and go into
the automatic mode.
The wipers operate intermittently, at low
speed, or at high speed and stops in
accordance with the amount of rainfall the
rainfall sensor detects.
■
AUTO sensitivity adjustment
When the wiper function is set to AUTO, you
can adjust the sensitivity of the rainfall sensor
(using the adjustment ring) so that wipers will
operate in accordance with your preference.
■
Automatic Intermittent Wipers
1Automatic Intermittent Wipers
The rainfall sensor is in the location shown below.
AUTO should always be turned OFF before the
following situations in order to prevent severe
damage to the wiper system:
• Cleaning the windscreen
• Driving through a car wash
• No rain present
a
Adjustment Ring
-: Low Sensitivity
+: High Sensitivity
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 201 ページ ２０２５年７月１８日　金曜日　午前９時２６分
202
uuOperating the Switches Around the Steering WheeluWipers and Washers
Controls
The rear wiper and washer can be used when
the power mode is in ON.
■
Wiper switch (OFF, INT, ON)
Change the wiper switch setting according to
the amount of rain.
■
Washer ( )
Sprays while you rotate the switch to this
position.
Hold it to activate the rear wiper and to spray
the washer. Once released, the washer spray
will stop and the rear wiper will return to its
selected switch setting after a few sweeps.
■
Operating in reverse
When you shift the transmission to
(R with the windscreen wipers activated, the
rear wiper operates automatically as follows even if its switch is off.
■
Rear Wiper/Washer
a
OFF
b
INT: Intermittent
c
ON: Continuous wipe
d
Washer
Front Wiper Position Rear Wiper Operation
AUTO (Intermittent) Intermittent
LO (Low speed wipe)
HI (High speed wipe)
Continuous
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 202 ページ ２０２５年７月１８日　金曜日　午前９時２６分
203
uuOperating the Switches Around the Steering WheeluRear Demister/Heated Door Mirror Button
Controls
Rear Demister/Heated Door Mirror Button
Press the rear demister and heated door
mirror button to demist the rear window and
mirrors when the power mode is in ON.
The rear demister and heated door mirror
automatically switch off after 10-30 minutes
depending on the outside temperature.
However, if the outside temperature is 0°C or
below, it does not automatically switch off.
1Rear Demister/Heated Door Mirror Button
This system consumes a lot of power, so turn it off
when the window has been demisted. Also, do not
use the system for a long time while the power
system is stopped. This may weaken the 12-volt
battery, making it difficult to turn the power system
on.
When the power mode is set to ON and the outside
temperature is below 5°C, the heated door mirror
may automatically activate for 10 minutes.
Auto-open/close function on all windows
Left-hand drive type
Right-hand drive type
26 JAZZ HEV Euro6e Sss (KE KG)-32TZA6500.book 203 ページ ２０２５年７月１８日　金曜日　午前９時２６分

Related Topics

Controls
Clock Locking and Unlocking the Doors Tailgate Security System Windows Adjusting the Steering Wheel Mirrors Seats Interior Convenience Items Climate Control System

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot