Get Specifications Guide for Kia Ceed SUV First Generation (2006-2012)

ED English 7.qxp 10/8/2007 5:51 PM Page 1

Maintenance services / 7-2

Normal maintenance schedule / 7-4, 7-10

Maintenance under severe usage conditions / 7-8, 7-14

Explanation of scheduled maintenance items / 7-16

Owner maintenance / 7-20

Engine compartment / 7-23

Engine oil / 7-25

Engine cooling system / 7-27

Brakes and clutch / 7-30

Automatic transaxle / 7-32

Lubricants and fluids / 7-34

Fuel filter / 7-35

Air cleaner / 7-36

Climate control air filter / 7-38

Wiper blades / 7-40

Battery / 7-43

Tires and wheels / 7-46

Maintenance

7

Bulb replacement / 7-55

Exterior care / 7-63

Interior care / 7-67

10

ED English 7.qxp 10/8/2007 5:51 PM Page 2

Maintenance

MAINTENANCE SERVICES

You should exercise the utmost care

to prevent damage to your vehicle

and injury to yourself whenever per-

forming any maintenance or inspec-

tion procedures.

Repairs and adjustments required as

a result of improper maintenance or

a lack of required maintenance are

not covered.

Owner’s responsibility

✽

NOTICE

Maintenance Service and Record

Retention are the owner's responsi-

bility.

We recommend you have your vehi-

cle maintained and repaired by an

authorized Kia dealer.

Should you have any doubts con-

cerning the inspection or servicing of

your vehicle, we strongly recom-

mend that you have an Authorized

Kia Dealer perform this work.

An authorized Kia dealer meets Kia’s

high service quality standards and

receives technical support from Kia

in order to provide you with a high

level of service satisfaction.

You should retain documents that

show proper maintenance has been

performed on your vehicle in accor-

dance with the scheduled mainte-

nance service charts shown on the

following pages. You need this infor-

mation to establish your compliance

with the servicing and maintenance

requirements of your Kia warranties.

An Authorized Kia Dealer has facto-

ry-trained technicians and genuine

Kia parts to service your vehicle

properly. For expert advice and qual-

ity service, see an Authorized Kia

Dealer.

Inadequate, incomplete or insuffi-

cient servicing may result in opera-

tional problems with your vehicle that

could lead to vehicle damage, an

accident, or personal injury.

Detailed warranty information is pro-

vided in your Warranty & Maintenance

book.

7 2

ED English 7.qxp 10/8/2007 5:51 PM Page 3

Maintenance

If your vehicle is operated under the

above conditions, you should

inspect, replace or refill more fre-

quently than the following Normal

Maintenance Schedule. After the

periods or distance shown in the

chart, continue to follow the pre-

scribed maintenance intervals.

Scheduled maintenance serv-

ice

Follow

Normal

Maintenance

Schedule if the vehicle is usually

operated where none of the following

conditions apply. If any of the following

conditions apply, follow Maintenance

Under Severe Usage Conditions.

• Repeated short distance driving.

• Driving in dusty conditions or

sandy areas.

• Extensive use of brakes.

• Driving in areas where salt or other

corrosive materials are being used.

• Driving on rough or muddy roads.

• Driving in mountainous areas.

• Extended periods of idling or low

speed operation.

• Driving for a prolonged period in

cold temperatures and/or extreme-

ly humid climates.

• More than 50% driving in heavy

city traffic during hot weather

above 32°C (90°F).

7 3

ED English 7.qxp 10/8/2007 5:51 PM Page 4

Maintenance

NORMAL MAINTENANCE SCHEDULE - GASOLINE ENGINE

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

10

15

I

24

20

30

I

36

30

45

I

48

40

60

I

60

50

75

I

72

60

90

I

84

70

105

I

96

80

120

I

Miles×1,000

Km×1,000

MAINTENANCE

ITEM

Drive belts *¹

Engine oil and engine oil filter *²

R

Inspect every 90,000 km (60,000 miles) or 48 months

and replace every 135,000 km (90,000 miles) or 72 months *³

Engine timing belt

2.0L Gasoline

Inspect when timing belt is inspected or replaced

Tensioner/idler

Air cleaner filter

I

R

I

R

I

1.4/1.6L Gasoline

2.0L Gasoline

Spark plugs

R

Valve clearance *⁴

Inspect every 90,000 km (60,000 miles) or 48 months *³

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*¹: Adjust alternator and power steering (and water pump drive belt) and air conditioner drive belt (if equipped).

Inspect and if necessary correct or replace.

*²: Check the engine oil level and leak every 500 km (350 miles) or before starting a long trip.

*³: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

*⁴: Inspect for excessive valve noise and/or engine vibration and adjust if necessary. An authroized KIA dealer

should perform the operation.

7 4

ED English 7.qxp 10/8/2007 5:51 PM Page 5

Maintenance

NORMAL MAINTENANCE SCHEDULE - GASOLINE ENGINE (cont.)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

10

15

24

20

30

I

36

30

45

48

60

50

75

72

60

90

I

84

70

96

Miles×1,000

Km×1,000

40

80

MAINTENANCE

ITEM

60

105

120

Vapor hose and fuel filler cap

Fuel tank air filter

I

Vacuum and crankcase ventilation hoses

Vacuum hose (for EGR & throttle body)

Fuel filter *⁵

I

Fuel lines, hoses and connections

I

Inspect “Coolant level adjustment and leak” every day

Inspect “Water pump” when replacing the drive belt or timing belt

Cooling system

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁵: Inspect and replace when there is a problem with starting the engine or fuel supplies.

7 5

ED English 7.qxp 10/8/2007 5:51 PM Page 6

Maintenance

NORMAL MAINTENANCE SCHEDULE - GASOLINE ENGINE (cont.)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

10

15

24

20

30

36

30

45

48

40

60

50

75

72

60

90

84

70

96

80

Miles×1,000

Km×1,000

MAINTENANCE

ITEM

105

120

At first, replace at 90,000 km (60,000 miles) or 60 months:

after that, replace every 45,000 km (30,000 miles) or 24 months *³

Engine coolant *⁶

Battery condition

I

All electrical systems

Brake lines, hoses and connections

Brake pedal, clutch pedal

Parking brake

I

Brake/clutch fluid

I

R

I

R

I

R

I

R

I

Disc brakes and pads

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*³: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

*⁶: When adding coolant, use only a qualified coolant additive for your vehicle and never mix hard water in the

coolant filled at the factory. An improper coolant mixture can result in serious malfunction or engine damage.

7 6

ED English 7.qxp 10/8/2007 5:51 PM Page 7

Maintenance

NORMAL MAINTENANCE SCHEDULE - GASOLINE ENGINE (cont.)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

24

36

48

60

72

60

90

I

84

96

Miles×1,000

Km×1,000

10

20

30

40

50

70

80

MAINTENANCE

ITEM

15

I

30

I

45

I

60

I

75

I

105

120

Steering gear rack, linkage and boots

Drive shaft and boots

I

Tire (pressure & tread wear)

I

Front suspension ball joints

I

Bolt and nuts on chassis and body

Air conditioner refrigerant (if equipped)

Air conditioner compressor (if equipped)

Climate control air filter (if equipped)

Manual transaxle fluid (if equipped)

Automatic transaxle fluid (if equipped)

I

R

I

R

I

R

I

R

I

R

I

R

I

R

I

R

I

R

I

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

7 7

ED English 7.qxp 10/8/2007 5:51 PM Page 8

Maintenance

MAINTENANCE UNDER SEVERE USAGE CONDITIONS - GASOLINE ENGINE

The following items must be serviced more frequently on cars mainly used under severe driving conditions.

Refer to the chart below for the appropriate maintenance intervals.

R : Replace

I : Inspect and if necessary, adjust, correct, clean or replace

Maintenance

operation

Maintenance intervals

MAINTENANCE ITEM

Engine oil and engine oil filter

Air cleaner filter

Driving condition

A, B, C, D, E,

F, G, H, I

R

Every 7,500 km (5,000 miles) or 6 months

Replace more frequently

R

I

C, E

depending on the condition

Replace more frequently

Spark plugs

B, H

depending on the condition

Engine timing belt

2.0L Gasoline

Every 60,000 km (40,000 miles) or 48 months

Every 100,000 km (62,500 miles)*¹

Every 45,000 km (30,000 miles)

D, E, F, G

Manual transaxle fluid (if equipped)

Automatic transaxle fluid (if equipped)

Steering gear rack, linkage and boots

C, D, E, G, H, I, J

A, C, E, F, G, H, I

C, D, E, F, G

Inspect more frequently

depending on the condition

*¹: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

7 8

ED English 7.qxp 10/8/2007 5:51 PM Page 9

Maintenance

operation

Maintenance intervals

MAINTENANCE ITEM

Front suspension ball joints

Disc brakes and pads, calipers and rotors

Parking brake

Inspect more frequently

I

C, D, E, F, G

C, D, E, G, H

C, D, G, H

depending on the condition

Inspect more frequently

depending on the condition

Inspect more frequently

I

depending on the condition

Inspect more frequently

Drive shaft and boots

I

C, D, E, F, G, H, I

C, E

depending on the condition

Inspect more frequently

Climate control air filter (if equipped)

R

depending on the condition

Severe driving conditions

A : Repeated short distance driving

B : Extensive idling

C : Driving in dusty, rough roads

D : Driving in areas using salt or other corrosive

materials or in very cold weather

E : Driving in sandy areas

G : Driving in mountainous areas.

H : Towing a trailer

I : Driving for patrol car, taxi, commercial car or vehicle

towing

J : Driving over 170 km/h (106 mile/h)

F : More than 50 % driving in heavy city traffic during

hot weather above 32 °C (90 °F)

7 9

ED English 7.qxp 10/8/2007 5:51 PM Page 10

Maintenance

NORMAL MAINTENANCE SCHEDULE - DIESEL ENGINE

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

12.5

20

I

24

25

40

I

36

37.5

60

I

48

50

80

I

60

62.5

100

I

72

75

120

I

84

87.5

140

I

96

100

160

I

Miles×1,000

Km×1,000

MAINTENANCE

ITEM

Drive belts *¹

Engine oil and engine oil filter *²

Engine timing belt

R

I

R

2.0L Diesel

R*³

Inspect when replacing the drive belt or timing belt

Tensioner/idler/damper pulley

Air cleaner filter

I

R

I

R

I

R

I

R

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*¹: Adjust alternator and power steering (and water pump drive belt) and air conditioner drive belt (if equipped).

Inspect and if necessary correct or replace.

*²: Check the engine oil level and leak every 500 km (350 miles) or before starting a long trip.

*³: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

7 10

ED English 7.qxp 10/8/2007 5:51 PM Page 11

Maintenance

NORMAL MAINTENANCE SCHEDULE - DIESEL ENGINE (cont.)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

24

36

48

60

72

84

96

Miles×1,000

Km×1,000

12.5

25

37.5

50

62.5

75

87.5

100

MAINTENANCE

ITEM

20

40

60

80

100

120

140

160

Vapor hose and fuel filler cap

PCV and Crank ventilation hose

I

Vacuum hose (for EGR & throttle body)

Vacuum pump and vacuum hose

Vacuum pump oil hose

I

Fuel filter cartridge *⁴*⁵

R

I

R

I

Fuel lines, hoses and connections

Inspect “Coolant level adjustment and leak” every day

Inspect “Water pump” when replacing the drive belt or timing belt

Cooling system

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁴: If the diesel fuel specifications don't meet the European standards EN590, replace it more frequently.

Consult an authorized Kia dealer for details.

*⁵: Inspect and replace when there is a problem with starting the engine or fuel supplies.

7 11

ED English 7.qxp 10/8/2007 5:51 PM Page 12

Maintenance

NORMAL MAINTENANCE SCHEDULE - DIESEL ENGINE (cont.)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

12.5

20

24

25

40

36

37.5

60

48

50

80

60

72

75

84

96

Miles×1,000

Km×1,000

62.5

100

87.5

140

100

160

MAINTENANCE

ITEM

120

At first, replace at 100,000 km (62,500 miles) or 60 months:

after that, replace every 40,000 km (25,000 miles) or 24 months *³

Engine coolant *⁶

Battery condition

I

All electrical systems

Brake lines, hoses and connections

Brake pedal, clutch pedal

Parking brake

I

Brake/clutch fluid

R

I

R

I

R

I

R

I

Disc brakes and pads

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*³: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

*⁶: When adding coolant, use only a qualified coolant additive for your vehicle and never mix hard water in the

coolant filled at the factory. An improper coolant mixture can result in serious malfunction or engine damage.

7 12

ED English 7.qxp 10/8/2007 5:51 PM Page 13

Maintenance

NORMAL MAINTENANCE SCHEDULE - DIESEL ENGINE (cont.)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

24

36

48

60

72

84

96

Miles×1,000

Km×1,000

12.5

25

37.5

50

62.5

75

87.5

100

MAINTENANCE

ITEM

20

40

60

80

100

120

140

160

Steering gear rack, linkage and boots

Drive shaft and boots

I

Tire (pressure & tread wear)

I

Front suspension ball joints

I

Bolt and nuts on chassis and body

Air conditioner refrigerant (if equipped)

Air conditioner compressor (if equipped)

Climate control air filter (if equipped)

Manual transaxle fluid (if equipped)

Automatic transaxle fluid (if equipped)

I

R

I

R

I

R

I

R

I

R

I

R

I

R

I

R

I

R

I

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

7 13

ED English 7.qxp 10/8/2007 5:51 PM Page 14

Maintenance

MAINTENANCE UNDER SEVERE USAGE CONDITIONS - DIESEL ENGINE

The following items must be serviced more frequently on cars mainly used under severe driving conditions.

Refer to the chart below for the appropriate maintenance intervals.

R : Replace

I : Inspect and if necessary, adjust, correct, clean or replace

Maintenance

operation

Maintenance intervals

MAINTENANCE ITEM

Engine oil and engine oil filter

Air cleaner filter

Driving condition

A, B, C, F, G,

H, I, J, K, L

R

Every 10,000 km (6,250 miles) or 6 months

Replace more frequently

R

I

C, E

depending on the condition

Engine timing belt

2.0L Diesel

Every 60,000 km (40,000 miles) or 48 months

Every 100,000 km (62,500 miles)*¹

Every 45,000 km (30,000 miles)

D, E, F, G

Manual transaxle fluid (if equipped)

Automatic transaxle fluid (if equipped)

Steering gear rack, linkage and boots

C, D, E, G, H, I, K

A, C, E, F, G, H, I

C, D, E, F, G

Inspect more frequently

depending on the condition

*¹: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

7 14

ED English 7.qxp 10/8/2007 5:51 PM Page 15

Maintenance

operation

Maintenance intervals

MAINTENANCE ITEM

Front suspension ball joints

Disc brakes and pads, calipers and rotors

Parking brake

Driving condition

C, D, E, F, G

C, D, E, G, H

C, D, G, H

Inspect more frequently

I

depending on the condition

Inspect more frequently

depending on the condition

Inspect more frequently

I

depending on the condition

Inspect more frequently

Drive shaft and boots

I

C, D, E, F, I, G, H

C, E

depending on the condition

Inspect more frequently

Climate control air filter (if equipped)

R

depending on the condition

Severe driving conditions

A : Repeated short distance driving

B : Extensive idling

C : Driving in dusty, rough roads

D : Driving in areas using salt or other corrosive

materials or in very cold weather

E : Driving in sandy areas

G : Driving in mountainous areas.

H : Towing a trailer

I : Driving for patrol car, taxi, commercial car or vehicle

towing

J : Driving in very cold weather

K : Driving over 170 km/h (106 mile/h)

L : Frequently driving in stop-and-go conditions

F : More than 50 % driving in heavy city traffic during

hot weather above 32 °C (90 °F)

7 15

ED English 7.qxp 10/8/2007 5:51 PM Page 16

Maintenance

EXPLANATION OF SCHEDULED MAINTENANCE ITEMS

Engine oil and filter

Fuel filter (cartridge)

Fuel lines, fuel hoses and con-

nections

The engine oil and filter should be A clogged filter can limit the speed at

changed at the intervals specified in which the vehicle may be driven,

the maintenance schedule. If the car damage the emission system and

is being driven in severe conditions, cause multiple issues such as hard

more frequent oil and filter changes starting. If an excessive amount of

Check the fuel lines, fuel hoses and

connections for leakage and dam-

age. Have an authorized KIA dealer

replace any damaged or leaking

parts immediately.

are required.

foreign matter accumulates in the

fuel tank, the filter may require

replacement more frequently.

Drive belts

WARNING - Diesel only

After installing a new filter, run the

engine for several minutes, and

check for leaks at the connections.

Fuel filters should be installed by an

authorized KIA dealer.

Inspect all drive belts for evidence of

cuts, cracks, excessive wear or oil

saturation and replace if necessary.

Drive belts should be checked peri-

odically for proper tension and

adjusted as necessary.

Never work on injection system

with engine running or within 30

seconds after shutting off

engine. High pressure pump,

rail, injectors and high pressure

pipes are subject to high pres-

sure even after the engine

stopped. The fuel jet produced

by fuel leaks may cause serious

injury, if it touch the body.

People

using

pacemakers

should not move than 30cm

closer to the ECU or wiring har-

ness within the engine room

while engine is running, since

the high currents in the

Common Rail system produce

considerable magnetic fields.

7 16

ED English 7.qxp 10/8/2007 5:51 PM Page 17

Maintenance

Timing belt (if equipped)

Vacuum crankcase ventilation

hoses (if equipped)

Air cleaner filter

Inspect all parts related to the timing

belt for damage and deformation.

Replace any damaged parts immedi-

ately.

A Genuine KIA air cleaner filter is

recommended when the filter is

replaced.

Inspect the surface of hoses for evi-

dence of heat and/or mechanical

damage. Hard and brittle rubber,

cracking, tears, cuts, abrasions, and

excessive swelling indicate deterio-

ration. Particular attention should be

paid to examine those hose surfaces

nearest to high heat sources, such

as the exhaust manifold.

Spark plugs (for gasoline

engine)

Vapor hose and fuel filler cap

The vapor hose and fuel filler cap

should be inspected at those inter-

vals specified in the maintenance

schedule. Make sure that a new

vapor hose or fuel filler cap is cor-

rectly replaced.

Make sure to install new spark plugs

of the correct heat range.

Valve clearance (if equipped)

Inspect the hose routing to assure

that the hoses do not come in con-

tact with any heat source, sharp

edges or moving component which

might cause heat damage or

mechanical wear. Inspect all hose

connections, such as clamps and

couplings, to make sure they are

secure, and that no leaks are pres-

ent. Hoses should be replaced

immediately if there is any evidence

of deterioration or damage.

Inspect excessive valve noise and/or

engine vibration and adjust if neces-

sary. An authorized KIA dealer

should perform the operation.

7 17

ED English 7.qxp 10/8/2007 5:51 PM Page 18

Maintenance

Cooling system

Automatic transaxle fluid

(if equipped)

Parking brake

Check cooling system components,

such as radiator, coolant reservoir,

hoses and connections for leakage

and damage. Replace any damaged

parts.

Inspect the parking brake system

including the parking brake pedal

and cables.

The fluid level should be in the "HOT"

range of the dipstick, after the engine

and transaxle are at normal operat-

ing temperature. Check the automat-

ic transaxle fluid level with the engine

running and the transaxle in neutral,

with the parking brake properly

applied.

Brake discs, pads, calipers

and rotors

Coolant

Check the pads for excessive wear,

discs for run out and wear, and

calipers for fluid leakage.

The coolant should be changed at

the intervals specified in the mainte-

nance schedule.

Brake hoses and lines

Suspension mounting bolts

Visually check for proper installation,

chafing, cracks, deterioration and

any leakage. Replace any deteriorat-

ed or damaged parts immediately.

Manual transaxle fluid

(if equipped)

Check the suspension connections

for looseness or damage. Retighten

to the specified torque.

Inspect the manual transaxle fluid

according to the maintenance sched-

ule.

Brake fluid

Check brake fluid level in the brake

fluid reservoir. The level should be

between “MIN” and “MAX” marks on

the side of the reservoir. Use only

hydraulic brake fluid conforming to

DOT 3 or DOT 4 specification.

7 18

ED English 7.qxp 10/8/2007 5:51 PM Page 19

Maintenance

Steering gear box, linkage &

boots/lower arm ball joint

Drive shafts and boots

Check the drive shafts, boots and

clamps for cracks, deterioration, or

damage. Replace any damaged

parts and, if necessary, repack the

grease.

With the vehicle stopped and engine

off, check for excessive free-play in

the steering wheel.

Check the linkage for bends or dam-

age. Check the dust boots and ball

joints for deterioration, cracks, or Air conditioning refrigerant

damage. Replace any damaged

parts.

(if equipped)

Check the air conditioning lines and

connections for leakage and dam-

age.

7 19

ED English 7.qxp 10/8/2007 5:51 PM Page 20

Maintenance

OWNER MAINTENANCE

When you stop for fuel:

While operating your vehicle:

Owner maintenance schedule

• Check the engine oil level.

• Note any changes in the sound of

the exhaust or any smell of

exhaust fumes in the vehicle.

The following lists are vehicle checks

and inspections that should be per-

formed by the owner or an

Authorized Kia Dealer at the fre-

quencies indicated to help ensure

safe, dependable operation of your

vehicle.

• Check coolant level in coolant

reservoir.

• Check for vibrations in the steering

wheel. Notice any increased steer-

ing effort or looseness in the steer-

ing wheel, or change in its straight-

ahead position.

WARNING

Be careful when checking your

engine coolant level when the

engine is hot. Scalding hot

coolant and steam may blow out

under pressure. This could

cause serious injury.

Any adverse conditions should be

brought to the attention of your deal-

er as soon as possible.

• Notice if your vehicle constantly

turns slightly or “pulls” to one side

when traveling on smooth, level

road.

These Owner Maintenance Checks

are generally not covered by war-

ranties and you may be charged for

labor, parts and lubricants used.

• When stopping, listen and check

for strange sounds, pulling to one

side, increased brake pedal travel

or “hard-to-push” brake pedal.

• Check the windshield washer fluid

level.

• Look for low or under-inflated tires.

• If any slipping or changes in the

operation of your transaxle occurs,

check the transaxle fluid level.

• Check automatic transaxle

(Park) function.

P

• Check parking brake.

• Check for fluid leaks under your

vehicle (water dripping from the air

conditioning system after use is

normal).

7 20

ED English 7.qxp 10/8/2007 5:51 PM Page 21

Maintenance

At least monthly:

At least twice a year

(i.e., every Spring and Fall) :

At least once a year :

• Check coolant level in the coolant

recovery reservoir.

• Clean body and door drain holes.

• Check radiator, heater, inter cooler,

turbocharger and air conditioning

hoses for leaks or da-mage.

• Lubricate door hinges and checks,

and hood hinges.

• Check the operation of all exterior

lights, including the stoplights, turn

signals and hazard warning flash-

ers.

• Lubricate door and hood locks and

latches.

• Check windshield washer spray

and wiper operation. Clean wiper

blades with clean cloth dampened

with washer fluid.

• Lubricate door rubber weather-

strips.

• Check the inflation pressures of all

tires including the spare.

• Check the air conditioning system

before the warm weather season.

• Check headlight alignment.

• Check muffler, exhaust pipes,

shields and clamps.

• Inspect and lubricate automatic

transaxle linkage and controls.

• Check the lap/shoulder belts for

wear and function.

• Clean battery and terminals.

• Check the brake fluid level.

• Check for worn tires and loose

wheel lug nuts.

7 21

ED English 7.qxp 10/8/2007 5:51 PM Page 22

Maintenance

Owner maintenance precau-

tions

WARNING - Maintenance

work

WARNING - Diesel Engine

Never work on injection system

with engine running or within 30

seconds after shutting off

engine. High-pressure pump,

rail, injectors and high-pressure

pipes are subject to high pres-

sure even after the engine

stopped. The fuel jet produced

by fuel leaks may cause serious

injury, if it touches the body.

Improper or incomplete service may

result in problems. This section gives

instructions only for the maintenance

items that are easy to perform.

• Performing maintenance work

on a vehicle can be danger-

ous. You can be seriously

injured while performing some

maintenance procedures. If

you lack sufficient knowledge

and experience or the proper

tools and equipment to do the

work, have it done by an

Authorized Kia Dealer.

As explained earlier in this section,

several procedures can be done only

by an Authorized Kia Dealer with

special tools.

People

using

pacemakers

✽

NOTICE

should not move than 30cm

closer to the ECU or wiring har-

ness within the engine room

while engine is running, since

the high currents in the elec-

tronic engine control system

produce considerable magnetic

fields.

• Working under the hood with

the engine running is danger-

ous. It becomes even more

dangerous when you wear

jewelry or loose clothing.

These can become entangled

in moving parts and result in

injury. Therefore, if you must

run the engine while working

under the hood, make certain

that you remove all jewelry

(especially rings, bracelets,

watches, and necklaces) and

all neckties, scarves, and sim-

ilar loose clothing before get-

ting near the engine or cool-

ing fans.

Improper owner maintenance dur-

ing the warranty period may affect

warranty coverage. For details, read

the separate Kia Warranty &

Maintenance book provided with

the vehicle. If you're unsure about

any servicing or maintenance proce-

dure, have it done by an Authorized

Kia Dealer.

7 22

ED English 7.qxp 10/8/2007 5:51 PM Page 23

Maintenance

ENGINE COMPARTMENT

■ 1.4L/1.6L Gasoline Engine

1. Engine oil filler cap

2. Engine oil dipstick

3. Air cleaner

4. Brake fluid reservoir

5. Fuse box

6. Negative battery terminal

7. Positive battery terminal

8. Radiator cap

■ 2.0L Gasoline Engine

9. Auto transaxle oil dipstick (if equipped)

10. Windshield washer fluid reservoir

11. Engine coolant reservoir

OED076001/OED076002

7 23

ED English 7.qxp 10/8/2007 5:51 PM Page 24

Maintenance

■ 1.6L Diesel Engine

1. Engine oil filler cap

2. Engine oil dipstick

3. Air cleaner

4. Brake fluid reservoir

5. Fuse box

6. Negative battery terminal

7. Positive battery terminal

8. Radiator cap

■ 2.0L Diesel Engine

9. Windshield washer fluid reservoir

10. Engine coolant reservoir

OED076004/OED076003

7 24

ED English 7.qxp 10/8/2007 5:51 PM Page 25

Maintenance

ENGINE OIL

4. Pull the dipstick out, wipe it clean,

and re-insert it fully.

WARNING - Radiator hose

Be very careful not to touch the

radiator hose when checking or

adding the engine oil as it may

be hot enough to burn you.

5. Pull the dipstick out again and

check the level. The level should

be between F and L.

OED076007

OED076005

If it is near or at L, add enough oil to

bring the level to F. Do not overfill.

Checking the engine oil level

1. Be sure the vehicle is on level

ground.

Use only the specified engine oil.

(Refer to “Recommended Lubricants”

in chapter 8.)

2. Start the engine and allow it to

reach normal operating tempera-

ture.

3. Turn the engine off and wait for a

few minutes (about 5 minutes) for

the oil to return to the oil pan.

7 25

ED English 7.qxp 10/8/2007 5:51 PM Page 26

Maintenance

Changing the engine oil and

filter

WARNING

Used engine oil may cause irri-

tation or cancer of the skin if left

in contact with the skin for pro-

longed periods of time. Used

engine oil contains chemicals

that have caused cancer in lab-

oratory animals. Always protect

your skin by washing your

hands thoroughly with soap and

warm water as soon as possible

after handling used oil.

Have engine oil and filter changed by

an authorized KIA dealer according

to the Maintenance Schedule at the

beginning of this section.

7 26

ED English 7.qxp 10/8/2007 5:51 PM Page 27

Maintenance

ENGINE COOLING SYSTEM

The high-pressure cooling system

has a reservoir filled with year-round

antifreeze coolant. The reservoir is

filled at the factory.

Checking the coolant level

(Continued)

• Even if the engine is not oper-

ating, do not remove the radi-

ator cap or the drain plug

while the engine and radiator

are hot. Hot coolant and steam

may still blow out under pres-

sure, causing serious injury.

WARNING - Removing

radiator cap

Check the antifreeze protection and

coolant level at least once a year, at

the beginning of the winter season,

and before traveling to a colder cli-

mate.

• Never attempt to remove the

radiator cap while the engine

is operating or hot. Doing so

might lead to cooling system

and engine damage and could

result in serious personal

injury from escaping hot

coolant or steam.

• Turn the engine off and wait

until it cools down. Even then,

use extreme care when

removing the radiator cap.

Wrap a thick towel around it,

and turn it counterclockwise

slowly to the first stop. Step

back while the pressure is

released from the cooling sys-

tem. When you are sure all the

pressure has been released,

press down on the cap, using

a thick towel, and continue

turning counterclockwise to

remove it.

(Continued)

7 27

ED English 7.qxp 10/8/2007 5:51 PM Page 28

Maintenance

Type A

The coolant level should be filled

between F and L or MAX and MIN

marked on the side of the coolant

reservoir when the engine is cool.

Recommended engine coolant

• Use only soft (de-mineralized)

water in the coolant mixture.

• The engine in your vehicle has alu-

minum engine parts and must be

protected by an ethylene-glycol-

based coolant to prevent corrosion

and freezing.

If the coolant level is low, add enough

specified coolant to provide protec-

tion against freezing and corrosion.

Bring the level to F, but do not over-

fill. If frequent additions are required,

see an Authorized Kia Dealer for a

cooling system inspection.

• DO NOT USE alcohol or methanol

coolant or mix them with the spec-

ified coolant.

OED076020

Type B

• Do not use a solution that contains

more than 60% antifreeze or less

than 35% antifreeze, which would

reduce the effectiveness of the

solution.

OED076024A

Check the condition and connections

of all cooling system hoses and

heater hoses. Replace any swollen

or deteriorated hoses.

7 28

ED English 7.qxp 10/8/2007 5:51 PM Page 29

Maintenance

Type A

For mixture percentage, refer to the

following table.

WARNING

Do not remove the radiator cap

when the engine and radiator

are hot. Scalding hot coolant

and steam may blow out under

pressure. This could cause seri-

ous injury.

Mixture Percentage (volume)

Ambient

Temperature

Coolant

Water

Solution

-15°C (5°F)

-25°C (-13°F)

-35°C (-31°F)

-45°C (-49°F)

35

40

50

60

65

60

50

40

OED076022

OED076024

OED076056

Type B

Changing the coolant

Have coolant changed by an author-

ized KIA dealer according to the

Maintenance Schedule at the begin-

ning of this section.

CAUTION

Put a thick cloth or fabric

around the radiator cap before

refilling the coolant in order to

prevent the coolant from over-

flowing into engine parts such

as generator.

Type C

7 29

ED English 7.qxp 10/8/2007 5:51 PM Page 30

Maintenance

BRAKES AND CLUTCH (IF EQUIPPED)

If the level is low, add fluid to the

WARNING

MAX level. The level will fall with

accumulated mileage. This is a nor-

mal condition associated with the

wear of the brake linings. If the fluid

level is excessively low, have the

brake system checked by an

Authorized Kia Dealer.

In the event the brake system

requires frequent additions of

fluid, the vehicle should be

inspected by an Authorized Kia

Dealer.

Use only the specified brake/clutch

fluid. (Refer to “Recommended

Lubricants” in chapter 8.)

OED076023

Checking brake/clutch fluid

level

Never mix different types of fluid.

Check the fluid level in the reservoir

periodically. The fluid level should be

between MAX and MIN marks on the

side of the reservoir.

Before removing the reservoir cap

and adding brake/clutch fluid, clean

the area around the reservoir cap

thoroughly to prevent brake/clutch

fluid contamination.

7 30

ED English 7.qxp 10/8/2007 5:51 PM Page 31

Maintenance

CAUTION

WARNING

Do not allow brake/clutch fluid

to contact the vehicle's body

paint, as paint damage will

result. Brake/clutch fluid, which

has been exposed to open air

for an extended time should

never be used as its quality can-

not be guaranteed. It should be

thrown out. Don't put in the

wrong kind of fluid. For exam-

ple, just a few drops of mineral-

based oil, such as engine oil, in

your brake clutch system can

damage brake clutch system

parts.

When changing and adding

brake/clutch fluid, handle it

carefully. Do not let it come in

contact with your eyes. If

brake/clutch fluid should come

in contact with your eyes, imme-

diately flush them with a large

quantity of fresh tap water. Have

your eyes examined by a doctor

as soon as possible.

7 31

ED English 7.qxp 10/8/2007 5:51 PM Page 32

Maintenance

AUTOMATIC TRANSAXLE (IF EQUIPPED)

1. Place the shift lever in N (Neutral)

position and confirm the engine is

running at normal idle speed.

2. After the transaxle is warmed up

sufficiently [(fluid temperature

70~80°C (158~176°F)], for exam-

ple by 10 minutes usual driving,

move the shift lever through all

positions then place the shift lever

in N (Neutral) or P (Park) position.

HOT

COLD

OHD076045N

OED076025

3. Confirm if the fluid level is in the

"HOT" range on the level gauge. If

the fluid level is lower, add the

specified fluid from the fill hole. If

the fluid level is higher, drain the

fluid from the drain hole.

Checking the automatic

transaxle fluid level

The automatic transaxle fluid level

should be checked regularly.

Keep the vehicle on level ground with

the parking brake applied and check

the fluid level according to the follow-

ing procedure.

4. If the fluid level is checked in cold

condition [(fluid temperature

20~30°C (68~86°F)], add the fluid

to the "COLD" line and then

recheck the fluid level according to

the above step 2.

7 32

ED English 7.qxp 10/8/2007 5:51 PM Page 33

Maintenance

✽

NOTICE

WARNING

WARNING - Parking brake

New automatic transaxle fluid

should be red. The red dye is added

so the assembly plant can identify it

as automatic transaxle fluid and dis-

tinguish it from engine oil or

antifreeze. The red dye, which is not

an indicator of fluid quality, is not

permanent. As the vehicle is driven,

the automatic transaxle fluid will

begin to look darker. The color may

eventually appear light brown.

Therefore, have an Authorized Kia

dealer change the automatic

transaxle fluid according to the

Scheduled Maintenance at the

beginning of this section.

The transaxle fluid level should

be checked when the engine is

at normal operating tempera-

ture. This means that the

engine, radiator, radiator hose

and exhaust system etc., are

very hot. Exercise great care not

to burn yourself during this pro-

cedure.

To avoid sudden movement of

the vehicle, apply parking brake

and depress the brake pedal

before moving the shift lever.

✽

NOTICE

“COLD” scale is for reference only

and should NOT be used to deter-

mine transaxle fluid level.

CAUTION

• Low fluid level causes

transaxle slippage. Overfilling

can cause foaming, loss of

fluid and transaxle malfunc-

tion.

Changing the automatic

transaxle fluid

• The use of a non-specified

fluid could result in transaxle

malfunction and failure.

Have automatic transaxle fluid

changed by an authorized KIA deal-

er according to the Maintenance

Schedule at the beginning of this

section.

7 33

ED English 7.qxp 10/8/2007 5:51 PM Page 34

Maintenance

LUBRICANTS AND FLUIDS

Body lubrication

WARNING

All moving points of the body, such

as door hinges, hood hinges, and

locks, should be lubricated each time

the engine oil is changed. Use a non-

freezing lubricant on locks during

cold weather.

• Do not use radiator coolant or

antifreeze in the washer fluid

reservoir.

• Radiator coolant can severely

obscure

visibility

when

sprayed on the windshield

and may cause loss of vehicle

control or damage to paint

and body trim.

Make sure the engine hood second-

ary latch keeps the hood from open-

ing when the primary latch is

released.

OED076026

• Windshield

washer

fluid

Checking the washer fluid

level

agents contain some amounts

of alcohol and can be flamma-

ble under certain circum-

stances. Do not allow sparks

or flame to contact the washer

fluid or the washer fluid reser-

voir. Damage to the vehicle or

it's occupants could occur.

The reservoir is translucent so that

you can check the level with a quick

visual inspection.

Check the fluid level in the washer

fluid reservoir and add fluid if neces-

sary. Plain water may be used if

washer fluid is not available.

However, use washer solvent with

antifreeze characteristics in cold cli-

mates to prevent freezing.

• Windshield washer fluid is

poisonous to humans and ani-

mals. Do not drink and avoid

contacting windshield washer

fluid. Serious injury or death

could occur.

7 34

ED English 7.qxp 10/8/2007 5:51 PM Page 35

Maintenance

FUEL FILTER (FOR DIESEL)

The fuel filter for diesel engine plays

an important role of separating water

from fuel and accumulating the water

in its bottom.

✽

NOTICE

ꢀ Use cloths when you extract air so

that the fuel is not sprayed

around.

ꢀ Clean the fuel around the fuel fil-

ter or the injection pump before

starting the engine to prevent fire.

ꢀ Finally, check each part if the fuel

is leaking.

If water accumulates in the fuel filter,

the warning light comes on when the

ignition key is in the “ON” position.

If the light is turned on, take

your car to the authorized

Kia dealer and have drain

the water and checked the

system.

OED076009

Extracting air in the fuel filter

(1.6L Diesel engine)

CAUTION

If the water accumulated in the

fuel filter is not drained at prop-

er times, damages to the major

parts such as the fuel system

can be caused by water perme-

ation in the fuel filter.

If you drove until you have no fuel left

or if you replaced the fuel filter, be

sure to extract air in the fuel system

as it makes you difficult to start the

engine.

1. Remove the air extract nozzle cap

on the fuel filter.

2. Pump up and down until the fuel

flows out of the plug opening.

7 35

ED English 7.qxp 10/8/2007 5:51 PM Page 36

Maintenance

AIR CLEANER

OED076028

Filter replacement

OED076029

OED076030

1. Loosen the air cleaner cover 2. Replace the air cleaner filter.

attaching clips and open the cover.

3. Lock the cover with the cover

attaching clips.

It must be replaced when necessary.

7 36

ED English 7.qxp 10/8/2007 5:51 PM Page 37

Maintenance

Replace the filter according to the

Scheduled Maintenance Section.

CAUTION

• Do not drive with the air clean-

er removed; this will result in

excessive engine wear.

If the vehicle is operated in extreme-

ly dusty or sandy areas, replace the

filter more often than the usual rec-

ommended intervals. (Refer to

Maintenance Under Severe Usage

Conditions in this section.)

• When removing the air cleaner

filter, be careful that dust or

dirt does not enter the air

intake, or damage may result.

• Use a KIA genuine part. Use of

non-genuine part could dam-

age the air flow sensor or tur-

bocharger.

7 37

ED English 7.qxp 10/8/2007 5:51 PM Page 38

Maintenance

CLIMATE CONTROL AIR FILTER (IF EQUIPPED)

The climate control air filter should

be replaced according to the mainte-

nance schedule. If the vehicle is

operated in the severely air-polluted

cities or on dusty rough roads for a

long period, it should be inspected

more frequently and replaced earlier.

When you try to replace the climate

control air filter by owner mainte-

nance, replace it performing the fol-

lowing procedure, and in this case,

be careful to avoid damaging other

components.

Outside air

Recirculated

air

Blower

Climate control

air filter

Heater core

Evaporator

core

1LDA5047

OED076032

The climate control air filter installed

behind the glove box filters the dust

or other pollutants that come into the

vehicle from the outside through the

heating and air conditioning system.

If dust or other pollutants accumulate

in the filter over a period of time, the

air flow from the air vents may

decrease, resulting in moisture accu-

mulation on the inside of the wind-

shield even when the outside (fresh)

are position is selected. If this hap-

pens, have the climate control air fil-

ter replaced by an Authorized Kia

Dealer.

Filter replacement

1. With the glove box open, remove

the stoppers on both sides to allow

the glove box hang freely on the

hinges.

7 38

ED English 7.qxp 10/8/2007 5:51 PM Page 39

Maintenance

OED076033

OED076031

OED076034

2. Open the glove box part way, 3. Pull out the cover pressing the 4. Replace the climate control air filter.

reach inside and pull out the elas-

tic line and push the retaining clip

through the hole on the side of the

glove box. Allow the glove box to

open.

hooks of the climate control air fil-

ter case.

5. Reassemble in the reverse order

of disassembly.

✽

NOTICE

When replacing the climate control

air filter install it properly.

Otherwise, the system may produce

noise and the effectiveness of the fil-

ter may be reduced.

7 39

ED English 7.qxp 10/8/2007 5:51 PM Page 40

Maintenance

WIPER BLADES

Wiper blade maintenance

Windshield wiper blade

replacement

✽

NOTICE

When the wipers no longer clean

adequately, the blades may be worn

or cracked, and require replacement.

Commercial hot waxes applied by

automatic car washes have been

known to make the windshield diffi-

cult to clean.

CAUTION

Contamination of either the wind-

shield or the wiper blades with for-

eign matter can reduce the effective-

ness of the windshield wipers.

Common sources of contamination

are insects, tree sap, and hot wax

treatments used by some commer-

cial car washes. If the blades are not

wiping properly, clean both the win-

dow and the blades with a good

cleaner or mild detergent, and rinse

thoroughly with clean water.

To prevent damage to the wiper

arms or other components, do

not attempt to move the wipers

manually.

OED046039

1. Turn the ignition swich off and

remove the key.

CAUTION

2. Push the wiper lever downward to

the one touch wiper position for

more than 2 seconds, then the

wiper blades will stop upward

position. (if equipped)

The use of a non-specified

wiper blade could result in

wiper malfunction and failure.

CAUTION

To prevent damage to the wiper

blades, do not use gasoline,

kerosene, paint thinner, or other

solvents on or near them.

7 40

ED English 7.qxp 10/8/2007 5:51 PM Page 41

Maintenance

OEN076047

OEN076048

OEN076049

3. Raise the wiper arm and turn the 4. Compress the clip and slide the 6. Install the blade assembly until it

wiper blade assembly to expose

the plastic locking clip.

blade assembly upward.

clicks into place.

5. Lift it off the arm.

7. Place back the wiper arm to the

proper position.

✽

NOTICE

Do not allow the wiper arm to fall

against the windshield.

7 41

ED English 7.qxp 10/8/2007 5:51 PM Page 42

Maintenance

OED076040

OED076041

Rear window wiper blade

replacement (if equipped)

2. Install the new blade assembly by

inserting the center part into the

slot in the wiper arm until it clicks

into place.

1. Raise the wiper arm and pull out

the wiper blade assembly.

3. Make sure the blade assembly is

installed firmly by trying to pulling

it slightly.

4. Place back the wiper arm to the

proper position.

7 42

ED English 7.qxp 10/8/2007 5:51 PM Page 43

Maintenance

BATTERY

(Continued)

WARNING - Battery

dangers

If any electrolyte gets

into your eyes, flush your

eyes with clean water for

at least 15 minutes and

get immediate medical

attention. If possible,

continue to apply water

with a sponge or cloth

until medical attention is

received.

Always read the follow-

ing instructions carefully

when handling a battery.

Keep lighted cigarettes

and all other flames or

sparks away from the

battery.

OED076042

Hydrogen, which is a

highly combustible gas,

is always present in bat-

tery cells and may

explode if ignited.

If electrolyte gets on

your skin, thoroughly

wash the contacted area.

If you feel a pain or a

burning sensation, get

medical attention imme-

diately.

For best battery service :

• Keep the battery securely mount-

ed.

• Keep the battery top clean and dry.

Keep batteries out of the

reach

• Keep the terminals and connec-

tions clean, tight, and coated with

petroleum jelly or terminal grease.

of

children

because batteries con-

tain highly corrosive

SULFURIC ACID. Do not

allow battery acid to con-

tact your skin, eyes,

clothing or paint finish.

Wear eye protection

when charging or work-

• Rinse any spilled electrolyte from

the battery immediately with a

solution of water and baking soda.

ing near

a

battery.

Always provide ventila-

tion when working in an

enclosed space.

• If the vehicle is not going to be

used for an extended time, discon-

nect the battery cables.

(Continued)

7 43

ED English 7.qxp 10/8/2007 5:51 PM Page 44

Maintenance

Battery recharging

(Continued)

WARNING - Recharging

battery

Your vehicle has a maintenance-free,

calcium-based battery.

• When lifting a plastic-cased

battery, excessive pressure on

the case may cause battery

acid to leak, resulting in per-

sonal injury. Lift with a battery

carrier or with your hands on

opposite corners.

When recharging the battery,

observe the following precau-

tions:

• If the battery becomes discharged

in a short time (because, for exam-

ple, the headlights or interior lights

were left on while the vehicle was

not in use), recharge it by slow

charging (trickle) for 10 hours.

• The battery must be removed

from the vehicle and placed in

an area with good ventilation.

• Never attempt to charge the

battery when the battery

cables are connected.

• Do not allow cigarettes,

sparks, or flame near the bat-

tery.

• If the battery gradually discharges

because of high electric load while

the vehicle is being used, recharge

it at 20-30A for two hours.

• The electrical ignition system

works with high voltage.

Never touch these compo-

nents with the engine running

or the ignition switched on.

• Watch the battery during

charging, and stop or reduce

the charging rate if the battery

cells begin gassing (boiling)

violently or if the temperature

of the electrolyte of any cell

exceeds 49°C (120°F).

• Wear eye protection when

checking the battery during

charging.

(Continued)

7 44

ED English 7.qxp 10/8/2007 5:51 PM Page 45

Maintenance

Reset items

(Continued)

WARNING

Items should be reset after the bat-

tery has been discharged or the bat-

tery has been disconnected.

• Disconnect the battery charg-

er in the following order.

• Before performing mainte-

nance or recharging the bat-

tery, turn off all accessories

and stop the engine.

1. Turn off the battery charger

main switch.

• Auto up/down window

(See chapter 3)

2. Unhook the negative clamp

from the negative battery ter-

minal.

• The negative battery cable

must be removed first and

installed last when the battery

is disconnected.

• Sunroof (See chapter 3)

• Trip computer (See chapter 4)

• Climate control system

(See chapter 4)

3. Unhook the positive clamp

from the positive battery ter-

minal.

• Clock (See chapter 3, 4)

• Audio (See chapter 3)

7 45

ED English 7.qxp 10/8/2007 5:51 PM Page 46

Maintenance

TIRES AND WHEELS

Tires care

CAUTION

For proper maintenance, safety, and

maximum fuel economy, you must

always maintain recommended tire

inflation pressures and stay within

the load limits and weight distribution

recommended for your vehicle.

• Warm tires normally exceed

recommended cold tire pres-

sures by 28 to 41 kPa (4 to 6

psi). Do not release air from

warm tires to adjust the pres-

sure or the tires will be under-

inflated.

Recommended cold tire infla-

tion pressures

• Underinflation

excessive wear, poor han-

dling, reduced fuel economy,

results

in

All tire pressures (including the

spare) should be checked every day

when the tires are cold. “Cold Tires”

means the vehicle has not been driv-

en for at least three hours or driven

less than 1.6 km (one mile).

OED076043

and

the

possibility

of

All specifications (sizes and pres-

sures) can be found on a label

attached to the front driver’s door sill.

blowouts from overheated

tires. Also, low tire pressure

can cause poor sealing of the

tire bead. If the tire pressure is

excessively low, wheel defor-

mation and/or tire separation

is possible. So, keep your tire

pressures at the proper levels.

If a tire frequently needs refill-

ing, have it checked by an

Authorized Kia Dealer.

WARNING

Recommended pressures must be

maintained for the best ride, top vehi-

cle handling, and minimum tire wear.

Severe underinflation (70 kPa

(10 psi) or more) can lead to

severe heat build-up, especially

on hot days and when driving at

high speed. This can potentially

cause tread separation and

other tire irregularities to

appear that can result in the

loss of vehicle control leading

to severe injury or death.

(Continued)

7 46

ED English 7.qxp 10/8/2007 5:51 PM Page 47

Maintenance

Checking tire inflation pres-

sure

(Continued)

CAUTION - Tire pressure

Always observe the following:

• Overinflation produces

a

Check your tires once a month or

more.

harsh ride, handling prob-

lems, excessive wear at the

center of the tire tread, and a

greater possibility of damage

from road hazards.

• Check tire pressure when the

tires are cold. (After vehicle

has been parked for at least

three hours or hasn't been

driven more than 1.6 km (one

mile) since startup.)

Also, check the tire pressure of the

spare tire.

• Be sure to reinstall the tire

inflation valve caps. Without

the valve cap, dirt or moisture

could get into the valve core

and cause air leakage. If the

cap have been lost, install new

one as soon as possible.

How to check

Use a good quality gage to check tire

pressure.You can not tell if your tires

are properly inflated simply by look-

ing at them. Radial tires may look

properly inflated even when they're

underinflated.

• Check the pressure of your

spare tire each time you check

the pressure of other tires.

• Never overload your vehicle.

Be careful not to overload a

vehicle luggage rack if your

vehicle is equipped with one.

Check the tire's inflation pressure

when the tires are cold. - "Cold"

means your vehicle has been sitting

for at least three hours or driven no

more than 1.6 km (1 mile).

• Worn, old tires can cause acci-

dents. If your tread is badly

worn, or if your tires have

been damaged, replace them.

WARNING - Tire Inflation

Overinflation or underinflation

can reduce tire life, adversely

affect vehicle handling, and lead

to sudden tire failure.This could

result in loss of vehicle control.

7 47

ED English 7.qxp 10/8/2007 5:51 PM Page 48

Maintenance

Remove the valve cap from the tire

valve stem. Press the tire gage firm-

ly onto the valve to get a pressure

measurement. If the cold tire inflation

pressure matches the recommended

pressure on the tire and loading

information label, no further adjust-

ment is necessary. If the pressure is

With a full-size spare tire

Tire rotation

To equalize tread wear, it is recom-

mended that the tires be rotated

every 12,000 km (7,500 miles) or

sooner if irregular wear develops.

During rotation, check the tires for

correct balance.

low, add air until you reach the rec- When rotating tires, check for uneven

CBGQ0706

CBGQ0707

CBGQ0707A

ommended amount.

wear and damage. Abnormal wear is

usually caused by incorrect tire pres-

sure, improper wheel alignment, out-

of-balance wheels, severe braking or

severe cornering. Look for bumps or

bulges in the tread or side of tire.

Replace the tire if you find either of

these conditions. Replace the tire

also if you can see fabric or cord.

After rotation, be sure to bring the

front and rear tire pressures to spec-

ification and check lug nut tightness.

Without a spare tire

If you overfill the tire, release air by

pushing on the metal stem in the

center of the tire valve. Recheck the

tire pressure with the tire gage. Be

sure to put the valve caps back on

the valve stems. They help prevent

leaks by keeping out dirt and mois-

ture.

Directional tires (if equipped)

Refer to Section 8, Specifications.

7 48

ED English 7.qxp 10/8/2007 5:51 PM Page 49

Maintenance

Disc brake pads should be inspected

for wear whenever tires are rotated.

Wheel alignment and tire

balance

Tread wear indicator

The wheels on your vehicle were

aligned and balanced carefully at the

factory to give you the longest tire life

and best overall performance.

✽

NOTICE

Rotate radial tires that have an

asymmetric tread pattern only from

front to rear and not from right to

left.

In most cases, you will not need to

have your wheels aligned again.

However, if you notice unusual tire

wear or your vehicle pulling one way

or the other, the alignment may need

to be reset.

WARNING

• Do not use the compact spare

tire for tire rotation

OEN076053

Tire replacement

If you notice your vehicle vibrating

• Do not mix bias ply and radial

ply tires under any circum-

stances. This may cause

unusual handling characteris-

tics that could result in death,

severe injury, or property

damage.

If the tire is worn evenly, a tread wear when driving on a smooth road, your

indicator will appear as a solid band wheels may need to be rebalanced.

across the tread. This shows there is

less than 1.6 mm (1/16 inch) of tread

left on the tire. Replace the tire when

this happens.

CAUTION

Improper wheel weights can

damage your vehicle's alu-

Do not wait for the band to appear

minum wheels. Use only

across the entire tread before replac-

approved wheel weights.

ing the tire.

7 49

ED English 7.qxp 10/8/2007 5:51 PM Page 50

Maintenance

Compact spare tire replacement

(if equipped)

(Continued)

WARNING

• The use of any other tire size

or type may seriously affect

ride, handling, ground clear-

ance, tire clearance, and

speedometer calibration.

• When replacing tires, never

mix radial, bias-belted, and

bias-type tires. All four tires

should be of the same size,

design and construction. Use

only the tire sizes listed on the

Tire Label found below the

door striker on the driver’s

side. Make sure that all tires

and wheels are the same size

and have the same load-carry-

ing capacity. Use only tire and

wheel combinations recom-

mended on the Tire Label or

by an Authorized Kia Dealer.

Failure to follow these precau-

tions can adversely affect the

safety and handling of your

vehicle.

A compact spare tire has a shorter

tread life than a regular size tire.

Replace it when you can see the

tread wear indicator bars on the tire.

The replacement compact spare tire

should be the same size and design

tire as the one provided with your

new vehicle and should be mounted

on the same compact spare tire

wheel. The compact spare tire is not

designed to be mounted on a regular

size wheel, and the compact spare

tire wheel is not designed for mount-

ing a regular size tire.

• Driving on worn-out tires is

very hazardous and will

reduce braking effectiveness,

steering accuracy, and trac-

tion.

• It is best to replace all four

tires at the same time. If that is

not possible, or necessary,

then replace the two front or

two rear tires as a pair.

Replacing just one tire can

seriously affect your vehicle’s

handling.

(Continued)

7 50

ED English 7.qxp 10/8/2007 5:52 PM Page 51

Maintenance

Wheel replacement

Tire traction

1

When replacing the metal wheels for Tire traction can be reduced if you

any reason, make sure the new drive on worn tires, tires that are

wheels are equivalent to the original improperly inflated or on slippery

factory units in diameter, rim width road surfaces. Tires should be

5,6

7

4

and offset.

replaced when tread wear indicators

appear. To reduce the possibility of

losing control, slow down whenever

there is rain, snow or ice on the road.

2

WARNING

3

A wheel that is not the correct

size may adversely affect wheel

and bearing life, braking and

stopping abilities, handling

characteristics, ground clear-

ance, body-to-tire clearance,

Tire maintenance

1

I030B04JM

In addition to proper inflation, correct

wheel alignment helps to decrease

tire wear. If you find a tire is worn

unevenly, have your dealer check the

wheel alignment.

Tire sidewall labeling

This information identifies and

describes the fundamental charac-

teristics of the tire and also provides

the tire identification number (TIN)

for safety standard certification. The

TIN can be used to identify the tire in

case of a recall.

snow

chain

clearance,

speedometer calibration, head-

light aim and bumper height.

When you have new tires installed,

make sure they are balanced. This

will increase vehicle ride comfort and

tire life. Additionally, a tire should

always be rebalanced if it is removed

from the wheel.

1. Manufacturer or brand name

Manufacturer or Brand name is

shown.

7 51

ED English 7.qxp 10/8/2007 5:52 PM Page 52

Maintenance

Tire speed ratings

2. Tire size designation

92 - Load Index, a numerical code

associated with the maximum

load the tire can carry.

The chart below lists many of the dif-

ferent speed ratings currently being

used for passenger cars. The speed

rating is part of the tire size designa-

tion on the sidewall of the tire. This

symbol corresponds to that tire's

designed maximum safe operating

speed.

A tire’s sidewall is marked with a tire

size designation. You will need this

information when selecting replace- H - Speed Rating Symbol. See the

ment tires for your car. The following

explains what the letters and num-

bers in the tire size designation

mean.

speed rating chart in this section

for additional information.

Wheel size designation

Wheels are also marked with impor-

Example tire size designation:

(These numbers are provided as an tant information that you need if you

example only; your tire size designa- ever have to replace one. The follow-

tor could vary depending on your ing explains what the letters and

Speed

Rating

Symbol

Maximum Speed

vehicle.)

numbers in the wheel size designa-

tion mean.

S

T

180 km/h (112 mph)

190 km/h (118 mph)

210 km/h (130 mph)

240 km/h (149 mph)

Above 240 km/h (149 mph)

270 km/h (168 mph)

P205/65R15 92H

H

Example wheel size designation:

P - Applicable vehicle type (tires

V

marked with the prefix “P’’ are 6.0JX15

intended for use on passenger

cars or light trucks; however, not

Z

W*

6.0 - Rim width in inches.

all tires have this marking).

* W speed rating is sub-category of the Z

speed rating.

J - Rim contour designation.

15 - Rim diameter in inches.

205 - Tire width in millimeters.

65 - Aspect ratio. The tire’s section

height as a percentage of its

width.

R - Tire construction code (Radial).

15 - Rim diameter in inches.

7 52

ED English 7.qxp 10/8/2007 5:52 PM Page 53

Maintenance

3. Checking tire life (TIN :Tire

Identification Number)

5. Maximum permissible inflation

pressure

WARNING - Tire age

Tires degrade over time, even

when they are not being used.

Regardless of the remaining

tread, it is recommended that

tires generally be replaced after

six (6) years of normal service.

Heat caused by hot climates or

frequent high loading conditions

can accelerate the aging

process. Failure to follow this

warning can result in sudden tire

failure, which could lead to a

loss of control and an accident

involving serious injury or death.

Any tires that are over 6 years, based

on the manufacturing date, tire

strength and performance, decline

with age naturally (even unused

spare tires). Therefore, the tires

(including the spare tire) should be

replaced by new ones. You can find

the manufacturing date on the tire

sidewall (possibly on the inside of the

wheel), displaying the DOT Code.

The DOT Code is a series of num-

bers on a tire consisting of numbers

and English letters. The manufactur-

ing date is designated by the last four

digits (characters) of the DOT code.

This number is the greatest amount

of air pressure that should be put in

the tire. Do not exceed the maximum

permissible inflation pressure. Refer

to the Tire and Loading Information

label for recommended inflation

pressure.

6. Maximum load rating

This number indicates the maximum

load in kilograms and pounds that

can be carried by the tire. When

replacing the tires on the vehicle,

always use a tire that has the same

load rating as the factory installed

tire.

4. Tire ply composition and mate-

rial

DOT : XXXX XXXX OOOO

The front part of the DOT means a

plant code number, tire size and

tread pattern and the last four num-

bers indicate week and year manu-

factured.

The number of layers or plies of rub-

ber-coated fabric are in the tire. Tire

manufacturers also must indicate the

materials in the tire, which include

steel, nylon, polyester, and others.

The letter "R" means radial ply con-

struction; the letter "D" means diago-

nal or bias ply construction; and the

letter "B" means belted-bias ply con-

struction.

For example:

DOT XXXX XXXX 1606 represents

that the tire was produced in the 16th

week of 2006.

7 53

ED English 7.qxp 10/8/2007 5:52 PM Page 54

Maintenance

Traction - AA, A, B & C

7. Uniform tire quality grading

Tread wear

WARNING - Tire

The traction grades, from highest to

lowest, are AA, A, B and C. The

grades represent the tires ability to

stop on wet pavement as measured

under controlled conditions on spec-

ified government test surfaces of

asphalt and concrete. A tire marked

C may have poor traction perform-

ance.

temperature

The tread wear grade is a compara-

tive rating based on the wear rate of

the tire when tested under controlled

conditions on a specified govern-

ment test course. For example, a tire

graded 150 would wear one-and-a-

half times as well on the government

course as a tire graded 100.

The temperature grade for this

tire is established for a tire that

is properly inflated and not

overloaded. Excessive speed,

underinflation, or excessive

loading, either separately or in

combination, can cause heat

build-up and possible sudden

tire failure. This can cause loss

of vehicle control and serious

injury or death.

The relative performance of tires

depends upon the actual conditions

of their use. However, performance

may differ from the norm because of

variations in driving habits, service

practices and differences in road

characteristics and climate.

Temperature -A, B & C

The temperature grades are A (the

highest), B and C. The grades repre-

sent the tire’s resistance to the gen-

eration of heat and its ability to dissi-

pate heat when tested under con-

trolled conditions on a specified

indoor laboratory test wheel.

These grades are molded on the

side-walls of passenger vehicle tires.

The tires available as standard or

optional equipment on your vehicles

may vary with respect to grade.

Sustained high temperature can

cause the material of the tire to

degenerate and reduce tire life, and

excessive temperature can lead to

sudden tire failure. Grades A and B

represent higher levels of perform-

ance on the laboratory test wheel

than the minimum required by the

law.

7 54

ED English 7.qxp 10/8/2007 5:52 PM Page 55

Maintenance

BULB REPLACEMENT

✽

NOTICE

CAUTION

WARNING - Working on

the lights

After heavy, driving rain or washing,

headlight and taillight lenses could

appear frosty. This condition is

caused by the temperature difference

between the lamp inside and outside.

This is similar to the condensation on

your windows inside your vehicle

during the rain and doesn’t indicate

a problem with your vehicle. If the

water leaks into the lamp bulb cir-

cuitry, have the vehicle checked by

an Authorized Kia Dealer.

If you don’t have necessary

tools, the correct bulbs and the

expertise, consult an Authorized

Kia Dealer. In many cases, it is

difficult to replace vehicle light

bulbs because other parts of the

vehicle must be removed before

you can get to the bulb. This is

especially true if you have to

remove the front bumper to get to

the bulb(s). Removing/installing

the front bumper or bumper hard-

ware can result in damage to the

vehicle.

Prior to working on the light,

firmly apply the parking brake,

ensure that the ignition switch

is turned to the “LOCK” position

and turn off the lights to avoid

sudden movement of the vehi-

cle and burning your fingers or

receiving an electric shock.

Use only the bulbs of the specified

wattage.

CAUTION

Be sure to replace the burned-

out bulb with one of the same

wattage rating. Otherwise, it

may cause damage to the fuse

or electric wiring system.

7 55

ED English 7.qxp 10/8/2007 5:52 PM Page 56

Maintenance

(Continued)

• If a bulb becomes damaged or

cracked, replace it immediate-

ly and carefully dispose of it.

• Wear eye protection when

changing a bulb. Allow the

bulb to cool down before han-

dling it.

OED076044

(1) Position light (Parking light)

(2) Headlight (High)

OHD076046

WARNING - Halogen bulbs

• Halogen bulbs contain pres-

surized gas that will produce

flying pieces of glass if broken.

(3) Headlight (Low)

(4) Front turn signal light

(5) Front fog light (if equipped)

• Always handle them carefully,

and avoid scratches and abra-

sions. If the bulbs are lit, avoid

contact with liquids. Never

touch the glass with bare

hands. Residual oil may cause

the bulb to overheat and burst

when lit. A bulb should be

operated only when installed

in a headlight.

Headlight bulb replacement

If the light bulb is not operating, have

the vehicle checked by an authorized

Kia Dealer.

(Continued)

7 56

ED English 7.qxp 10/8/2007 5:52 PM Page 57

Maintenance

4. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

Front fog light bulb replace-

ment

If the light bulb is not operating, have

the vehicle checked by an authorized

Kia Dealer.

5. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Insert the socket into the assembly

and turn the socket clockwise.

OED076045

Front turn signal/position light

bulb replacement

1. Open the hood.

2. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

3. Remove the bulb from the socket

by pressing it in and rotating it until

the tabs on the bulb align with the

slots in the socket. Pull the bulb

out of the socket.

7 57

ED English 7.qxp 10/8/2007 5:52 PM Page 58

Maintenance

Front map lamp

Glove box lamp

Interior lights bulb replace-

ment

1. Using a flat-blade screwdriver,

gently pry the lens from the interi-

or light housing.

WARNING

Prior to working on the Interior

Lights, ensure that the “OFF”

button is depressed to avoid

burning your fingers or receiv-

ing an electric shock.

OED076046

OED076049

Center dome lamp

Luggage room lamp

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb in the socket.

4. Align the lens tabs with the interior

light housing notches and snap

the lens into place.

OED076047

OED076050

7 58

ED English 7.qxp 10/8/2007 5:52 PM Page 59

Maintenance

Type A

Rear combination light bulb

replacement

(1) Rear fog light (if equipped)

(2) Rear turn signal light

(3) Back-up light

(4) Stop and tail light

(5) Tail light

OED076052

OED076051

Type B

Type C

License plate lights bulb

replacement

1. Loosen the lens retaining screws

with a cross-tip screwdriver.

2. Remove the lens.

3. Remove the bulb by pulling it

straight out.

4. Install a new bulb.

5. Reinstall the lens securely with the

lens retaining screws.

OED078058A/OED076058

7 59

ED English 7.qxp 10/8/2007 5:52 PM Page 60

Maintenance

Type A

OED076054

Type B

OED076053

1LDA5037

Type A / Type B

4. Remove the bulb from the socket

by pressing it in and rotating it until

the tabs on the bulb align with the

slots in the socket. Pull the bulb

out of the socket.

1. Open the rear hatch.

2. Remove the service cover by turn-

ing the plastic screw counterclock-

wise and removing the cover.

5. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

OED078054A

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

3. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

7. Reinstall the service cover and

tighten the screws.

7 60

ED English 7.qxp 10/8/2007 5:52 PM Page 61

Maintenance

5. Remove the bulb from the socket

by pressing it in and rotating it until

the tabs on the bulb align with the

slots in the socket. Pull the bulb

out of the socket.

6. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

7. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

OED076059

OED076063

8. Reinstall the light assembly to the

body of the vehicle.

9. Tighten the screws.

OED076060

OED076061

Type C

4. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

1. Open the rear hatch.

2. Loosen the light assembly retain-

ing screws with a cross-tip screw-

driver.

3. Remove the rear combination light

assembly from the body of the

vehicle.

7 61

ED English 7.qxp 10/8/2007 5:52 PM Page 62

Maintenance

4. Remove the bulb by pulling it

straight out.

5. Insert a new bulb in the socket.

6. Reassemble the socket and the

lens part.

7. Connect the bulb electrical con-

nector.

8. Reinstall the light assembly to the

body of the vehicle.

OED076055

OHD076036

High mounted stop light bulb

replacement

Side repeater light bulb

replacement (if equipped)

If the light bulb is not operating, have 1. Remove the light assembly from

the vehicle checked by an authorized

Kia Dealer.

the vehicle by pushing the lens for-

ward and pulling the assembly out.

2. Disconnect the bulb electrical con-

nector.

3. Separate the socket and the lens

parts by turning the socket count-

er clockwise until the tabs on the

socket align with the slots on the

lens part.

7 62

ED English 7.qxp 10/8/2007 5:52 PM Page 63

Maintenance

EXTERIOR CARE

Even prompt washing with plain

water may not completely remove all

these deposits. A mild soap, safe for

use on painted surfaces, may be

used.

Exterior general caution

It is very important to follow the label

directions when using any chemical

cleaner or polish. Read all warning

and caution statements that appear

on the label.

After washing, rinse the vehicle thor-

oughly with lukewarm or cold water.

Do not allow soap to dry on the fin-

ish.

Finish maintenance

Washing

To help protect your vehicle’s finish

from rust and deterioration, wash it

thoroughly and frequently at least

once a month with lukewarm or cold

water.

CAUTION

OJB037800

Do not use strong soap, chemi-

cal detergents or hot water, and

do not wash the vehicle in direct

sunlight or when the body of the

vehicle is warm.

CAUTION

• Water washing in the engine

compartment including high

pressure water washing may

cause the failure of electrical

circuits located in the engine

compartment.

If you use your vehicle for off-road

driving, you should wash it after each

off-road trip. Pay special attention to

the removal of any accumulation of

salt, dirt, mud, and other foreign

materials. Make sure the drain holes

in the lower edges of the doors and

rocker panels are kept clear and

clean.

WARNING

After washing the vehicle, test

the brakes while driving slowly

to see if they have been affected

by water. If braking performance

is impaired, dry the brakes by

applying them lightly while

maintaining a slow forward

speed.

• Never allow water or other liq-

uids come in contact with

electrical/electronic compo-

nents inside the vehicle as

this may damage them.

Insects, tar, tree sap, bird droppings,

industrial pollution and similar

deposits can damage your vehicle’s

finish if not removed immediately.

7 63

ED English 7.qxp 10/8/2007 5:52 PM Page 64

Maintenance

Waxing

Finish damage repair

CAUTION

Wax the vehicle when water will no

longer bead on the paint.

Deep scratches or stone chips in the

painted surface must be repaired

promptly. Exposed metal will quickly

rust and may develop into a major

repair expense.

• Wiping dust or dirt off the

body with a dry cloth will

scratch the finish.

Always wash and dry the vehicle

before waxing. Use a good quality

liquid or paste wax, and follow the

manufacturer’s instructions. Wax all

metal trim to protect it and to main-

tain its luster.

• Do not use steel wool, abra-

sive cleaners, or strong deter-

gents containing highly alka-

line or caustic agents on

chrome-plated or anodized

aluminum parts. This may

result in damage to the pro-

tective coating and cause dis-

coloration or paint deteriora-

tion.

✽

NOTICE

If your vehicle is damaged and

requires any metal repair or

replacement, be sure the body shop

applies anti-corrosion materials to

the parts repaired or replaced.

Removing oil, tar, and similar materi-

als with a spot remover will usually

strip the wax from the finish. Be sure

to re-wax these areas even if the rest

of the vehicle does not yet need wax-

ing.

7 64

ED English 7.qxp 10/8/2007 5:52 PM Page 65

Maintenance

Bright-metal maintenance

Underbody maintenance

WARNING

• To remove road tar and insects, Corrosive materials used for ice and

use a tar remover, not a scraper or snow removal and dust control may

other sharp object.

After washing the vehicle, test

the brakes while driving slowly

to see if they have been affected

by water. If braking performance

is impaired, dry the brakes by

applying them lightly while

maintaining a slow forward

speed.

collect on the underbody. If these

materials are not removed, acceler-

ated rusting can occur on underbody

parts such as the fuel lines, frame,

floor pan and exhaust system, even

though they have been treated with

rust protection.

• To protect the surfaces of bright-

metal parts from corrosion, apply a

coating of wax or chrome preser-

vative and rub to a high luster.

• During winter weather or in coastal

areas, cover the bright metal parts

with a heavier coating of wax or

preservative. If necessary, coat the

parts with non-corrosive petroleum

jelly or other protective compound.

Thoroughly flush the vehicle under-

body and wheel openings with luke-

warm or cold water once a month,

after off-road driving and at the end

of each winter. Pay special attention

to these areas because it is difficult

to see all the mud and dirt. It will do

more harm than good to wet down

the road grime without removing it.

The lower edges of doors, rocker

panels, and frame members have

drain holes that should not be

allowed to clog with dirt; trapped

water in these areas can cause rust-

ing.

7 65

ED English 7.qxp 10/8/2007 5:52 PM Page 66

Maintenance

Aluminum wheel maintenance

The aluminum wheels are coated

with a clear protective finish.

• Do not use any abrasive cleaner,

polishing compound, solvent, or

wire brushes on aluminum wheels.

They may scratch or damage the

finish.

• Use only a mild soap or neutral

detergent, and rinse thoroughly

with water. Also, be sure to clean

the wheels after driving on salted

roads. This helps prevent corro-

sion.

• Avoid washing the wheels with

high-speed car wash brushes.

• Do not use any acid detergent. It

may damage and corrode the alu-

minum wheels coated with a clear

protective finish.

7 66

ED English 7.qxp 10/8/2007 5:52 PM Page 67

Maintenance

INTERIOR CARE

Fabric

Interior general precautions

Cleaning the lap/shoulder belt

webbing

Remove dust and loose dirt from fab-

ric with a whisk broom or vacuum

cleaner. Clean with a mild soap solu-

tion recommended for upholstery or

carpets. Remove fresh spots imme-

diately with a fabric spot cleaner. If

fresh spots do not receive immediate

attention, the fabric can be stained

and its color can be affected. Also, its

fire-resistant properties can be

reduced if the material is not proper-

ly maintained.

Prevent caustic solutions such as

perfume and cosmetic oil from con-

tacting the dashboard and door trim

because they may cause damage or

discoloration. If they do contact the

dashboard, wipe them off immedi-

ately. See the instructions that follow

for the proper way to clean vinyl.

Clean the belt webbing with any mild

soap solution recommended for

cleaning upholstery or carpet. Follow

the instructions provided with the

soap. Do not bleach or re-dye the

webbing because this may weaken

it.

Cleaning the interior window

glass

CAUTION

If wax for synthetic leather con-

tacts the dashboard and door

trim, it may cause stain and blot.

If the interior glass surfaces of the

vehicle become fogged (that is, cov-

ered with an oily, greasy or waxy

film), they should be cleaned with

glass cleaner. Follow the directions

on the glass cleaner container.

CAUTION

Using anything but recommend-

ed cleaners and procedures

may affect the fabric’s appear-

ance and fire-resistant proper-

ties.

Cleaning the upholstery and

interior trim

Vinyl

CAUTION

Remove dust and loose dirt from

vinyl with a whisk broom or vacuum

cleaner. Clean vinyl surfaces with a

vinyl cleaner.

Do not scrape or scratch the

inside of the rear window. This

may result in damage to the rear

window defroster grid.

7 67

Specifications for Your Kia Ceed SUV First Generation (2006-2012)

Related Topics

Popular Owner Manuals

Latest Owner Manuals