2004-2010 Kia Picanto 4 Door Driving your vehicle -> Starting the engine User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driving your vehicle -> Starting the engine for Your Kia Picanto 4 Door First Generation (2004-2010)

Driving your vehicle  
STARTING THE ENGINE  
E040000AUN-EU  
4. In extremely cold weather (below  
-18°C / 0°F) or after the vehicle has  
not been operated for several days, let  
the engine warm up without depress-  
ing the accelerator.  
(Continued)  
• Never reach for the ignition switch,  
or any other controls through the  
steering wheel while the vehicle is  
in motion. The presence of your  
hand or arm in this area could  
cause a loss of vehicle control, an  
accident and serious bodily injury  
or death.  
WARNING  
Always wear appropriate shoes  
when operating your vehicle.  
Unsuitable shoes (high heels, ski  
boots,etc.) may interfere with your  
ability to use the brake and acceler-  
ator pedal.  
Whether the engine is cold or warm, it  
should be started without depressing  
the accelerator.  
• Do not place any movable objects  
around the driver’s seat as they  
may move while driving, interfere  
with the driver and lead to an acci-  
dent.  
CAUTION  
If the engine stalls while you are in  
motion, do not attempt to move the  
shift lever to the P (Park) position. If  
traffic and road conditions permit,  
you may put the shift lever in the N  
(Neutral) position while the vehicle  
is still moving and turn the ignition  
switch to the START position in an  
attempt to restart the engine.  
E040100AUN  
Starting the gasoline engine  
1. Make sure the parking brake is  
applied.  
2. Manual Transaxle - Depress the  
clutch pedal fully and shift the  
transaxle into Neutral. Keep the clutch  
pedal and brake pedal depressed  
while turning the ignition switch to the  
start position.  
Automatic Transaxle - Place the  
transaxle shift lever in P (Park).  
Depress the brake pedal fully.  
You can also start the engine when  
the shift lever is in the N (Neutral)  
position.  
CAUTION  
Do not engage the starter for more  
than 10 seconds. If the engine stalls  
or fails to start, wait 5 to 10 seconds  
before re-engaging the starter.  
Improper use of the starter may  
damage it.  
3. Turn the ignition switch to START and  
hold it there until the engine starts (a  
maximum of 10 seconds), then  
release the key.  
5 5  
Driving your vehicle  
E040101ASA  
Starting and stopping the engine for tur-  
bocharger intercooler (if equipped)  
Starting the diesel engine  
Glow indicator light  
1. Do not race or accelerate the engine  
immediately after starting.  
To start the diesel engine when the  
engine is cold, it has to be pre-heated  
before starting the engine and then have  
to be warmed up before starting to drive.  
If the engine is cold, idle for several  
seconds before sufficient lubrication is  
ensured in the turbocharger unit.  
1. Make sure the parking brake is  
applied.  
2. After high speed or extended driving,  
requiring a heavy engine load, idle the  
engine about 1 minute before turning it  
off.  
2. Manual Transaxle - Depress the  
clutch pedal fully and shift the  
transaxle into Neutral. Keep the clutch  
pedal and brake pedal depressed  
while turning the ignition switch to the  
start position.  
This idle time will allow the tur-  
bocharger to cool prior to shutting the  
engine off.  
W-60  
3. Turn the ignition switch to the ON posi-  
tion to pre-heat the engine. Then the  
glow indicator light will illuminate.  
Automatic Transaxle - Place the  
transaxle shift lever in P(park).  
Depress the brake pedal fully.  
CAUTION  
4. If the glow indicator light goes out, turn  
the ignition switch to the START posi-  
tion and hold it there until the engine  
starts (a maximum of 10 seconds),  
then release the key.  
Do not turn the engine off immedi-  
ately after it has been subjected to  
a heavy load. Doing so may cause  
severe damage to the engine or tur-  
bocharger unit.  
You can also start the engine when the  
shift lever is in the N(neutral) position.  
NOTICE  
If the engine does not start within 10  
seconds after the preheating is complet-  
ed, turn the ignition switch once more to  
the LOCK position for 10 seconds, and  
then to the ON position, in order to pre-  
heat again.  
5 6  

Related Topics

Popular Owner Manuals