Get Safety features of your vehicle -> Child restraint system (CRS) Guide for Kia Picanto 4 Door Third Generation (2019-2026)

Safety features of your vehicle

Child restraint system (CRS)

When to replace seat belts

Child restraint system (CRS)

Entire in-use seat belt assembly or

Our recommendation: Children

assemblies should be replaced if the

always in the rear

vehicle has been involved in an accident.

This should be done even if no damage

WARNING

is visible. In this case, have the system

Always properly restrain children in the

replaced by a professional workshop.

vehicle. Children of all ages are safer

Kia recommends to consult an

when riding in the rear seats. Never

authorised Kia dealer/service partner.

place a rearward-facing Child Restraint

System on the front passenger seat,

unless the air bag is deactivated.

Children under age 13 should always

ride in the rear seats and must always be

properly restrained to minimise the risk

of injury in an accident, sudden stop or

sudden manoeuvre.

According to accident statistics, children

are safer when properly restrained in the

rear seats than in the front seat. Children

too large for a Child Restraint System

must use the seat belts provided.

Most countries have regulations which

require children to travel in approved

Child Restraint Systems.

The laws governing the age or height/

weight restrictions at which seat belts

can be used instead of Child Restraint

System differs among countries, so you

should be aware of the specific require-

ments in your country, and where you

are travelling.

Child Restraint Systems must be prop-

erly installed in the vehicle seat. Always

use a commercially available Child

Restraint System that meets the require-

ments of your country.

Child Restraint System (CRS)

Infants and younger children must be

restrained in an appropriate rearward

facing or forward-facing CRS that has

first been properly secured to the seat of

Safety features of your vehicle

Child restraint system (CRS)

the vehicle. Read and comply with the

tions, please refer to the installation

instructions for installation and use pro-

tables.

vided by the manufacturer of the Child

僅 Read and comply with the warnings

Restraint System.

and instructions for installation and

use provided with the Child Restraint

WARNING

System.

僅 Always follow the Child Restraint Sys-

Child Restraint System types

tem manufacturer’s instructions for

installation and use.

There are three main types of Child

Restraint Systems: rearward-facing, for-

僅 Always properly restrain your child in

ward-facing and booster Child Restraint

the Child Restraint System.

Systems.

僅 Do not use an infant carrier or a child

They are classified according to the

safety seat that “hooks” over a seat-

child’s age, height and weight.

back, it may not provide adequate

protection in an accident.

Rearward-facing Child Restraint

僅 After an accident, have the system

System

checked by a professional workshop.

Kia recommends to visit an authorised

Kia dealer/service partner.

Selecting a Child Restraint Sys-

tem (CRS)

ONQ5021098N

When selecting a Child Restraint System

A rearward-facing Child Restraint Sys-

for your child, always:

tem provides restraint with the seating

僅 Make sure the Child Restraint System

surface against the back of the child.

has a label certifying that it meets

The harness system holds the child in

applicable Safety Standards of your

place, and in an accident, acts to keep

country.

the child positioned in the Child

A Child Restraint System may only be

Restraint Systems and reduce the stress

installed if it was approved in accor-

to the fragile neck and spinal cord.

dance with the requirements of

All children under the age of one year

ECER44, ECE-R129 or relevant regula-

must always ride in a rearwardfacing

tion.

Child Restraint System. There are differ-

僅 Select a Child Restraint System based

ent types of rearward-facing Child

on your child’s height and weight. The

Restraint Systems: infant-only Child

required label or the instructions for

Restraint Systems can only be used rear-

use typically provide this information.

ward-facing. Convertible and 3-in-1

僅 Select a Child Restraint System that

Child Restraint Systems typically have

fits the vehicle seating position where

higher height and weight limits for the

it will be used.

rearward-facing position, allowing you to

For the suitability of Child Restraint

keep your child rearward-facing for a

Systems on the vehicle's seating posi-

longer period of time.

Safety features of your vehicle

Child restraint system (CRS)

Installing a Child Restraint Sys-

Keep using Child Restraint Systems in

the rearward-facing position as long as

tem (CRS)

children fit within the height and weight

WARNING

limits allowed by the Child Restraint Sys-

tem's manufacturer.

Before installing your Child Restraint

System always:

Forward-facing Child Restraint

Read and follow the instructions pro-

System

vided by the manufacturer of the Child

Restraint System.

Failure to follow all warnings and

instructions could increase the risk of

the SERIOUS INJURY or DEATH if an

accident occurs.

ONQ5021099N

A forward-facing Child Restraint System

WARNING

provides restraint for the child’s body

If the vehicle headrest prevents proper

with a harness. Keep children in a for-

installation of a Child Restraint System,

ward-facing Child Restraint System with

the headrest of the respective seating

a harness until they reach the top height

position shall be readjusted or entirely

or weight limit allowed by your Child

removed.

Restraint System’s manufacturer.

Once your child outgrows the forward-

After selecting a proper Child Restraint

facing Child Restraint System, your child

System for your child and checking that

is ready for a booster seat.

the Child Restraint System fits properly

on the seating position, there are three

Booster seats

general steps for a proper installation:

A booster seat is a Child Restraint Sys-

僅 Properly secure the Child Restraint

tem designed to improve the fit of the

System to the vehicle. All Child

vehicle’s seat belt system. A booster seat

Restraint Systems must be secured to

positions the seat belt so that it fits prop-

the vehicle with the lap belt or lap part

erly over the stronger parts of your

of a lap/shoulder belt or with the ISO-

child’s body. Keep your children in

FIX toptether and/or ISOFIX anchor-

booster seats until they are big enough

age and/or with the support leg.

to fit in a seat belt properly.

僅 Make sure the Child Restraint Sys-

For a seat belt to fit properly, the lap belt

tem is firmly secured. After installing

must lie comfortable across the upper

a Child Restraint System to the vehi-

thighs, not the stomach. The shoulder

cle, push and pull the seat forward

belt should lie comfortable across the

and from side-to-side to verify that it

shoulder and chest and not across the

is securely attached to the seat. A

neck or face. Children under age 13

Child Restraint System secured with a

must always be properly restrained to

seat belt should be installed as firmly

minimise the risk of injury in an accident,

as possible. However, some side-

sudden stop or sudden manoeuvre.

toside movement can be expected.

Safety features of your vehicle

Child restraint system (CRS)

When installing a Child Restraint Sys-

The Child Restraint System manufac-

tem, adjust the vehicle seat and seat-

turer will provide you with instructions

back (up and down, forward and

on how to use the Child Restraint Sys-

rearward) so that your child fits in the

tem with its attachments for the ISOFIX

Child Restraint System in a comfort-

anchorages.

able manner.

ISOFIX anchorages have been provided

僅 Secure the child in the Child

in the left and right outboard rear seat-

Restraint System. Make sure the

ing positions. Their locations are shown

child is properly strapped in the Child

in the illustration.

Restraint System according to the

Child Restraint System manufac-

turer’s instructions.

CAUTION

A Child Restraint System in a closed

vehicle can become very hot. To prevent

OJAPE023027

burns, check the seating surface and

WARNING

buckles before placing your child in the

Child Restraint System.

Do not attempt to install a Child

Restraint System using ISOFIX anchor-

ISOFIX anchorage and top-tether

ages in the rear centre seating position.

anchorage (ISOFIX anchorage

There are no ISOFIX anchorages pro-

vided for this seat. Using the outboard

system) for children

seat anchorages, for the CRS installation

The ISOFIX system holds a Child

on the rear centre seating position, can

Restraint System during driving and in

damage the anchorages.

an accident. This system is designed to

make installation of the Child Restraint

Type A

System easier and reduce the possibility

of improperly installing your Child

Restraint System. The ISOFIX system

uses anchors in the vehicle and attach-

ments on the Child Restraint System.

The ISOFIX system eliminates the need

to use seat belts to secure the Child

Restraint System to the rear seats.

ISOFIX anchorages are metal bars built

into the vehicle. There are two lower

anchors for each ISOFIX seating position

that will accommodate a Child Restraint

System with lower attachments.

OJAPE023028_3

To use the ISOFIX system in your vehi-

cle, you must have a Child Restraint Sys-

tem with ISOFIX attachments.

Safety features of your vehicle

Child restraint system (CRS)

Type B

Restraint System to the ISOFIX

anchorages.

WARNING

Take the following precautions when

using the ISOFIX system:

僅 Read and follow all installation

instructions provided with your Child

Restraint System.

僅 To prevent the child from reaching

and taking hold of unretracted seat

belts, buckle all unused rear seat belts

and retract the seat belt webbing

OJAPE023028L_3

behind the child. Children can be

ISOFIX anchorages are located between

strangled if a shoulder belt becomes

the seatback and the seat cushion of the

wrapped around their neck and the

rear seat left and right outboard seating

seat belt tightens.

positions, indicated by the symbols.

僅 NEVER attach more than one Child

* 1 : ISOFIX Anchor Position Indicator

Restraint System to a single anchor-

(Type A- p z v m p ,Type B-

) 2 :

age. This could cause the anchor or

ISOFIX Anchor

attachment to come loose or break.

Securing a Child Restraint System

僅 Always have the ISOFIX system

with the “ISOFIX Anchorage Sys-

inspected by your dealer after an

accident. An accident can damage the

tem”

ISOFIX system and may not properly

To install an i-Size or ISOFIX-compatible

secure the Child Restraint System.

Child Restraint System in either of the

rear outboard seating positions:

Securing a Child Restraint System

1. Move the seat belt buckle away from

seat with “Top-tether Anchor-

the ISOFIX anchorages.

age” system

2. Move any other objects away from

Child restraint system top tether anchor-

the anchorages that could prevent a

ages are located on the back of the rear

secure connection between the Child

seatbacks.

Restraint System and the ISOFIX

anchorages.

3. Place the Child Restraint System on

the vehicle seat, then attach the seat

to the ISOFIX anchorages according

to the instructions provided by the

Child Restraint System manufacturer.

4. Follow the instructions of the Child

Restraint System's manufacturer for

proper installation and connection of

the ISOFIX attachments on the Child

Safety features of your vehicle

Child restraint system (CRS)

僅 Do not attach the top-tether to any-

thing other than the correct top-tether

anchorage. It may not work properly if

attached to something else.

僅 Child Restraint anchorages are

designed to withstand only those

loads imposed by correctly fitted

Child Restraints.

Under no circumstances are they to

be used for adult seatbelts, harnesses,

or for attaching other items or equip-

ment to the vehicle.

OJA030017

1. Route the Child Restraint System top-

tether strap over the seatback. Plac-

Securing a Child Restraint System

ing the top tether strap, please follow

with a lap/shoulder belt

the instructions of the Child Restraint

When not using the ISOFIX system, all

System manufacturer.

Child Restraint Systems must be

2. Connect the top-tether strap to the

secured to a rear seat with the lap part

top-tether anchorage, then tighten

of a lap/shoulder belt.

the top-tether strap according to the

Installing a Child Restraint Sys-

instructions of your Child Restraint

tem with a lap/shoulder belt

System's manufacturer to firmly

attach the Child Restraint System to

To install a Child Restraint System on the

the seat.

rear seats, do the following:

1. Place the Child Restraint System on a

rear seat and route the lap/ shoulder

belt around or through the Child

Restraint System, following the Child

Restraint System manufacturer’s

instructions.

OCV031116N

Make sure the seat belt webbing is

WARNING

not twisted.

Take the following precautions when

installing the top-tether:

僅 Read and follow all installation

instructions provided with your Child

Restraint System.

僅 NEVER attach more than one Child

OJAPE023026

Restraint System to a single ISOFIX

2. Fasten the lap/shoulder belt latch into

top-tether anchorage. This could

the buckle. Listen for the distinct

cause the anchorage or attachment to

“click” sound. Position the release but-

come loose or break.

Safety features of your vehicle

Child restraint system (CRS)

ton so that it is easy to access in case

of an emergency.

OJAPE023023

3. Remove as much slack from the belt

as possible by pushing down on the

Child Restraint System whilst feeding

the shoulder belt back into the retrac-

tor.

4. Push and pull on the Child Restraint

System to confirm that the seat belt is

holding it firmly in place.

OJAPE023024

If your Child Restraint System manufac-

turer recommends the use of a top-

tether with the lap/shoulder belt.

To remove the Child Restraint System,

press the release button on the buckle

and then pull the lap/shoulder belt out of

the Child Restraint System and allow the

seat belt to retract fully.

Safety features of your vehicle

Child restraint system (CRS)

Suitability of each seating position for belted & ISOFIX Child Restraint

Systems (CRS) according to UN regulations (For 4-seater, For Europe)

(Information for use by vehicle users and CRS manufacturers)

僅

Yes : Suitable for fitment of the designated category of CRS

僅

No : Not suitable for fitment of the designated category of CRS

僅

"-": Not applicable

僅

The table is based on LHD vehicle. Except for the front passenger seat, the table is valid for RHD vehicle.

For RHD vehicle front passenger of number 1 , please use information for the seating position number 3.

F: Forward facing

R: Rearward facing

Seating positions

CRS categories

1, 2

Airbag

Off

Yes *1

Yes

Universal belted CRS

All mass groups

F, R

ISOFIX CRF

i-size CRS

Yes

(F2, F2X, R1, R2)

Carry-cot

ISOFIX CRF

(ISOFIX lateral facing CRS)

(L1, L2)

ISOFIX infant* CRS

ISOFIX CRF

Yes

(* : ISOFIX baby CRS)

(R1)

ISOFIX CRF

Yes *2

ISOFIX toddler CRS - small

(F2,F2X, R2,R2X)

F, R

ISOFIX toddler CRS – large*

ISOFIX CRF

Yes *3

(*: not booster seats)

(F3, R3)

ISOFIX CRF

Booster Seat – reduced Width

Yes

(B2)

ISOFIX CRF

Booster Seat – full Width

Yes

(B3)

* 1. To install Universal CRS, 1st row passenger seat back angle should be at upright

position

* 2. For installation of R2 size CRS.

僅 Front Driver Seat : Seat Height should be up highest position.

(If height device does not exist, Seat should be moved 10mm in front of mid posi-

tion.)

僅 Front Passenger Seat : Seat should be moved foremost position.

* 3. The seating position (number4,6) is not suitable for fitment of R3 size CRS.

Safety features of your vehicle

Child restraint system (CRS)

Seat Number

Position in the vehicle

Seating positions

Front left

Front centre

Front right

2nd row left

2nd row centre

2nd row right

OJAPE023062L

* Never place a rearward facing Child Restraint System on the front passenger seat,

unless the air bag is deactivated.

* For semi-universal or vehicle specific CRS(ISOFIX or belted CRS), please see the

vehicle list provided in the manual of CRS.

* If the vehicle headrest prevents proper installation of a CRS, the headrest of the

seating position shall be readjusted or entirely removed

Safety features of your vehicle

Child restraint system (CRS)

Suitability of each seating position for belted & ISOFIX Child Restraint

Systems (CRS) according to UN regulations (For 5-seater, For Europe)

(Information for use by vehicle users and CRS manufacturers)

僅

Yes : Suitable for fitment of the designated category of CRS

僅

No : Not suitable for fitment of the designated category of CRS

僅

"-": Not applicable

僅

The table is based on LHD vehicle. Except for the front passenger seat, the table is valid for RHD vehicle.

For RHD vehicle front passenger of number 1 , please use information for the seating position number 3.

F: Forward facing

R: Rearward facing

Seating positions

CRS categories

1, 2

Airbag

Off

Yes *1

Yes

Universal belted CRS

All mass groups

F, R

ISOFIX CRF

i-size CRS

Yes

(F2, F2X, R1, R2)

Carry-cot

ISOFIX CRF

(ISOFIX lateral facing CRS)

(L1, L2)

ISOFIX infant* CRS

ISOFIX CRF

Yes

(* : ISOFIX baby CRS)

(R1)

ISOFIX CRF

Yes *2

ISOFIX toddler CRS - small

(F2,F2X, R2,R2X)

F, R

ISOFIX toddler CRS – large*

ISOFIX CRF

Yes *3

(*: not booster seats)

(F3, R3)

ISOFIX CRF

Booster Seat – reduced Width

Yes

(B2)

ISOFIX CRF

Booster Seat – full Width

Yes

(B3)

* 1. To install Universal CRS, 1st row passenger seat back angle should be at upright

position

* 2. For installation of R2 size CRS.

僅 Front Driver Seat : Seat Height should be up highest position.

(If height device does not exist, Seat should be moved 10mm in front of mid posi-

tion.)

僅 Front Passenger Seat : Seat should be moved foremost position.

* 3. The seating position (number4,6) is not suitable for fitment of R3 size CRS.

Safety features of your vehicle

Child restraint system (CRS)

Seat Number

Position in the vehicle

Seating positions

Front left

Front centre

Front right

2nd row left

2nd row centre

2nd row right

OJAPE023062L

* Never place a rearward facing Child Restraint System on the front passenger seat,

unless the air bag is deactivated.

* For semi-universal or vehicle specific CRS(ISOFIX or belted CRS), please see the

vehicle list provided in the manual of CRS.

* If the vehicle headrest prevents proper installation of a CRS, the headrest of the

seating position shall be readjusted or entirely removed

Safety features of your vehicle

Child restraint system (CRS)

Recommended CRS for Vehicle according to UN regulations

(Information for use by vehicle users and CRS manufacturers)

Child Height

ECE

Name

Manufacturer

Type of Fixation

Approval Number

Mass Group

BABY-SAFE 3 i-SIZE

ISOFIX with support leg

40~83㎝

Britax Romer

E1*129R03/04*0060

with FLEX BASE i-Sense

rearward facing

ISOFIX mounted with

76~105㎝

Trifix2 i-Size

Britax Romer

129R-010015

top-tether

100~150㎝

Solution T i-Fix

Cybex

ISOFIX and Vehicle belt

129R-030036

Booster Basic

Group 3

Graco

Vehicle belt

E11-0444165

(Junior III)

CRS Manufacturer information

Britax R쎨mer :

Cybex :

Graco :

Safety features of your vehicle

Child restraint system (CRS)

Suitability of each seating position for belted & ISOFIX Child Restraint

Systems (CRS) according to UN regulations (Except Europe)

(Information for use by vehicle users and CRS manufacturers)

僅

Yes : Suitable for fitment of the designated category of CRS

僅

No : Not suitable for fitment of the designated category of CRS

僅

"-": Not applicable

僅

The table is based on LHD vehicle. Except for the front passenger seat, the table is valid for RHD vehicle.

For RHD vehicle front passenger of number 1 , please use information for the seating position number 3.

F: Forward facing

R: Rearward facing

Seating positions

CRS categories

1, 2

Airbag

Off

Yes *1

Yes

Yes *2

Yes

Universal belted CRS

All mass groups

F, R

ISOFIX CRF

i-size CRS

(F2, F2X, R1, R2)

Carry-cot

ISOFIX CRF

(ISOFIX lateral facing CRS)

(L1, L2)

ISOFIX infant* CRS

ISOFIX CRF

Yes

(* : ISOFIX baby CRS)

(R1)

ISOFIX CRF

Yes *3

ISOFIX toddler CRS - small

(F2,F2X, R2,R2X)

F, R

ISOFIX toddler CRS – large*

ISOFIX CRF

Yes *4

(*: not booster seats)

(F3, R3)

ISOFIX CRF

Booster Seat – reduced Width

Yes

(B2)

ISOFIX CRF

Booster Seat – full Width

Yes

(B3)

* 1. To install Universal CRS, 1st row passenger seat back angle should be at upright

position

* 2. If seat don’t have shoulder belt, never place a rearward facing Child Restraint Sys-

tem

If seat don’t have any seat belt, never place an all Child Restraint System.

* 3. For installation of R2 size CRS.

僅 Front Driver Seat : Seat Height should be up highest position.

(If height device does not exist, Seat should be moved 10mm in front of mid posi-

tion.)

僅 Front Passenger Seat : Seat should be moved foremost position.

* 4. The seating position (number4,6) is not suitable for fitment of R3 size CRS.

$Safety features of your vehicleChild restraint system (CRS)Seat NumberPosition in the vehicleSeating positions1Front left2Front centre3Front right42nd row left52nd row centre62nd row rightOJAPE023062L* Never place a rearward facing Child Restraint System on the front passenger seat,unless the air bag is deactivated.3* For semi-universal or vehicle specific CRS(ISOFIX or belted CRS), please see thevehicle list provided in the manual of CRS.* If the vehicle headrest prevents proper installation of a CRS, the headrest of theseating position shall be readjusted or entirely removed* When Installing Child Restraint system on 2nd row seats, move the seat to CRS for Vehicle according to UN regulations (ForLATIN Market)(Information for use by vehicle users and CRS manufacturers)Mass GroupNameManufacturerType of FixationGroup 0+Citi SPSMaxi cosiSEAT BELTGroup I/II/IIIBeline SPNaniaSEAT BELTCRS Manufacturer informationMaxi Cosi : :$

Safety features of your vehicle

Child restraint system (CRS)

Seat Number

Position in the vehicle

Seating positions

Front left

Front centre

Front right

2nd row left

2nd row centre

2nd row right

OJAPE023062L

* Never place a rearward facing Child Restraint System on the front passenger seat,

unless the air bag is deactivated.

* For semi-universal or vehicle specific CRS(ISOFIX or belted CRS), please see the

vehicle list provided in the manual of CRS.

* If the vehicle headrest prevents proper installation of a CRS, the headrest of the

seating position shall be readjusted or entirely removed

* When Installing Child Restraint system on 2nd row seats, move the seat to mid-posi-

tion.

Recommended CRS for Vehicle according to UN regulations (For

LATIN Market)

(Information for use by vehicle users and CRS manufacturers)

Mass Group

Name

Manufacturer

Type of Fixation

Group 0+

Citi SPS

Maxi cosi

SEAT BELT

Group I/II/III

Beline SP

Nania

SEAT BELT

CRS Manufacturer information

Maxi Cosi :

NANIA :

Safety features of your vehicle -> Child restraint system (CRS) for Your Kia Picanto 4 Door Third Generation (2019-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals