Get Maintenance Guide for Kia Rio 4 Door Second Generation (2006-2010)

Maintenance ser vices / 7-2

Maintenance schedule / 7-3

Owner maintenance / 7-7

Engine compar tment / 7-9

Engine oil / 7-10

Engine cooling system / 7-11

Brake fluid / 7-13

Drive belts / 7-14

Power steering / 7-14

Automatic transaxle / 7-15

Lubr icants and fluids / 7-16

Air cleaner / 7-17

Climate control air filter / 7-18

Wiper blades / 7-19

Battery / 7-21

Tires and wheels / 7-23

Lubr icant specifications / 7-32

Exterior care / 7-33

Interior car e / 7-35

Maintenance

MAINTENANCE SERVICES

You should exercise the utmost care to

prevent damage to your vehicle and

injury to yourself whenever performing

any maintenance or inspection proce-

dures.

Should you have any doubts concerning

the inspection or servicing of your vehi-

cle, we strongly recommend that you

have an authorized Kia dealer perform

this work.

An authorized Kia dealer has factory-

trained technicians and genuine Kia

parts to service your vehicle properly. For

expert advice and quality service, see an

authorized Kia dealer.

Inadequate, incomplete or insufficient

servicing may result in operational prob-

lems with your vehicle that could lead to

vehicle damage, an accident, or person-

al injury.

Owner’s responsibility

Maintenance Service and Record

Retention are the owner's responsibil-

ity.

You should retain documents that show

proper maintenance has been performed

on your vehicle in accordance with the

scheduled maintenance service charts

shown on the following pages. You need

this information to establish your compli-

ance with the servicing and maintenance

requirements of your Kia warranties.

Detailed warranty information is provided

in your Warranty & Consumer Information

manual.

Repairs and adjustments required as a

result of improper maintenance or a lack

of required maintenance are not covered.

We strongly recommend that all vehicle

maintenance be performed by an author-

ized Kia dealer using genuine Kia parts.

7 3

Maintenance

MAINTENANCE SCHEDULE

Engine control system

Kilometers or time in months, whichever comes first

× 1,000 km 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128

# Months 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64

Engine oil & engine oil filter (1)

Drive belts (tension) I I I I

Cooling system hoses & connections I I I I I

Engine coolant (1) I I I I I R I I I I I R I I I I

Fuel filter R R

Fuel tank cap, lines, EVAP canister and hoses

I I

Fuel tank air filter I R I R I

Air cleaner element (2) I I I I I R I I I I I R I I I I

Ignition wires I I

Spark plugs R R

Idle speed I I I I I

Engine timing belt R

MAINTENANCE

INTERVALS

MAINTENANCE

ITEM

Replace every 6,000 km or 6 months.

Maintenance

MAINTENANCE SCHEDULE (CONTINUED)

Chassis and body

Kilometers or time in months, whichever comes first

× 1,000 km 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128

# Months 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64

Air conditioner compressor operation &

I I I I I

refrigerant amount (if equipped)

Exhaust pipes, heat shield & mountings I I I I I I I I

Front suspension ball joints I I I I

Brakes/clutch fluid (1) I I I I I I I R I I I I I I I R

Front brake pads & discs (3) I I I I I I I I I I I I I I I I

Rear brake pads & discs/drums (3) I I I I I I I I I I I I I I I I

Parking brake I I I I I I I I

Brake lines & connections

I I I I I

(including booster)

Manual transaxle oil (1) I I I R I I I R I I I R I I I R

Clutch & brake pedal free play I I I I I I I I I I I I I I I I

MAINTENANCE

INTERVALS

MAINTENANCE

ITEM

7 5

Maintenance

MAINTENANCE SCHEDULE (CONTINUED)

Chassis and body (Continued)

Kilometers or time in months, whichever comes first

× 1,000 km 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128

# Months 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64

Automatic transaxle fluid (1) I I I R I I I R I I I R I I I R

Chassis & underbody bolts & nuts I I I I I I I I I I I I I I I I

Tire condition & inflation pressure I I I I I I I I I I I I I I I I

Wheel alignment (4)

Tire rotation

Steering operation & linkage I I I I I I I I I I I I I I I I

Power steering fluid & lines I I I I I I I I

Driveshaft dust boots I I I I I

Seat belts, buckles & anchors I I I I I I I I I I I I I I I I

Lock, hinges & hood latch L L L L L L L L L L L L L L L L

MAINTENANCE

INTERVALS

MAINTENANCE

ITEM

Inspect when abnormal condition noted

Rotate the tires every 12,000 km

Maintenance

Chart symbols:

I- Inspect these items and their related parts. If necessary, correct, clean, refill, adjust or replace.

R- Replace or change

L- Lubricate.

(1) Refer to the lubricant and coolant specifications in the Owner’s Manual.

(2) More frequent maintenance is required if driving under dusty conditions.

(3) More frequent maintenance is required if the vehicle is operated under any of the following conditions:

a. Short-distance driving.

b. Driving on dusty roads.

c. Extensive idling or slow-speed driving in stop-and-go traffic.

(4) If necessary, rotate and balance the wheels.

* Note: Check the engine oil and coolant levels every week.

7 7

Maintenance

OWNER MAINTENANCE

Owner maintenance schedule

The following lists are vehicle checks and

inspections that should be performed by

the owner or an authorized Kia dealer at

the frequencies indicated to help ensure

safe, dependable operation of your vehi-

cle.

Any adverse conditions should be

brought to the attention of your dealer as

soon as possible.

These Owner Maintenance Checks are

generally not covered by warranties and

you may be charged for labor, parts and

lubricants used.

When you stop for fuel:

• Check the engine oil level.

• Check coolant level in coolant reser-

voir.

• Check the windshield washer fluid

level.

• Look for low or under-inflated tires.

While operating your vehicle:

• Note any changes in the sound of the

exhaust or any smell of exhaust fumes

in the vehicle.

• Check for vibrations in the steering

wheel. Notice any increased steering

effort or looseness in the steering

wheel, or change in its straight-ahead

position.

• Notice if your vehicle constantly turns

slightly or “pulls” to one side when trav-

eling on smooth, level road.

• When stopping, listen and check for

strange sounds, pulling to one side,

increased brake pedal travel or “hard-

to-push” brake pedal.

• If any slipping or changes in the oper-

ation of your transaxle occurs, check

the transaxle fluid level.

• Check automatic transaxle P (Park)

function.

• Check parking brake.

• Check for fluid leaks under your vehicle

(water dripping from the air condition-

ing system during or after use is nor-

mal).

At least monthly:

• Check coolant level in the coolant

recovery reservoir.

• Check the operation of all exterior

lights, including the stoplights, turn sig-

nals and hazard warning flashers.

• Check the inflation pressures of all

tires including the spare.

At least twice a year

(i.e., every Spring and Fall) :

• Check radiator, heater and air condi-

tioning hoses for leaks or damage.

• Check windshield washer spray and

wiper operation. Clean wiper blades

with clean cloth dampened with wash-

er fluid.

• Check headlight alignment.

• Check muffler, exhaust pipes, shields

and clamps.

• Check the lap/shoulder belts for wear

and function.

• Check for worn tires and loose wheel

lug nuts.

WARNING

Be careful when checking your

engine coolant level when the

engine is hot. Scalding hot coolant

and steam may blow out under

pressure. This could cause burns or

other serious injury.

Maintenance

At least once a year :

• Clean body and door drain holes.

• Lubricate door hinges and checks, and

hood hinges.

• Lubricate door and hood locks and

latches.

• Lubricate door rubber weatherstrips.

• Check the air conditioning system

before the warm weather season.

• Check the power steering fluid level.

• Inspect and lubricate automatic

transaxle linkage and controls.

• Clean battery and terminals.

• Check the brake fluid level.

Owner maintenance precautions

Improper or incomplete service may

result in problems. This section gives

instructions only for the maintenance

items that are easy to perform.

As explained earlier in this section, sev-

eral procedures can be done only by an

authorized Kia dealer with special tools.

Improper owner maintenance during

the warranty period may affect war-

ranty coverage. For details, read the

separate Kia Warranty & Consumer

Information Manual provided with the

vehicle. If you're unsure about any

servicing or maintenance procedure,

have it done by an Authorized Kia

Dealer.

WARNING - Maintenance

work

• Performing maintenance work on

a vehicle can be dangerous. You

can be seriously injured while per-

forming some maintenance pro-

cedures. If you lack sufficient

knowledge and experience or the

proper tools and equipment to do

the work, have it done by an

Authorized Kia Dealer.

• Working under the hood with the

engine running is dangerous. It

becomes even more dangerous

when you wear jewelry or loose

clothing. These can become

entangled in moving parts and

result in injury. Always remove all

loose or hanging clothing and all

jewelry before working on the

engine.

7 9

Maintenance

ENGINE COMPARTMENT

1JBA0004

1. Engine coolant reservoir

2. Engine oil filler cap

3. Brake fluid reservoir

4. Air cleaner

5. Fuse box

6. Negative battery terminal

7. Positive battery terminal

8. Auto transaxle oil dipstick

(if equipped)

9. Radiator cap

10. Engine oil dipstick

11. Power steering fluid reservoir

(if equipped)

12. Windshield washer fluid

reservoir

Maintenance

107

ENGINE OIL

Checking the engine oil level

1. Be sure the vehicle is on level ground.

2. Start the engine and allow it to reach

normal operating temperature.

3. Turn the engine off and wait for a few

minutes (about 5 minutes) for the oil to

return to the oil pan.

4. Pull the dipstick out, wipe it clean, and

re-insert it fully.

5. Pull the dipstick out again and check

the level. The level should be between

F and L.

If it is near or at L, add enough oil to bring

the level to F. Do not overfill.

Use only the specified engine oil. (Refer

to “Recommended Lubricants” later in

this section.)

Changing the engine oil and filter

Have engine oil and filter changed by an

Authorized Kia Dealer according to the

Maintenance Schedule at the beginning

of this section.

1JBA7035

WARNING -

Radiator hose

Be very careful not to touch the

radiator hose when checking or

adding the engine oil as it may be

hot enough to burn you.

1JBA7036

7 11

Maintenance

ENGINE COOLING SYSTEM

The high-pressure cooling system has a

reservoir filled with year-round antifreeze

coolant. The reservoir is filled at the fac-

tory.

Check the antifreeze protection and

coolant level at least once a year, at the

beginning of the winter season, and

before traveling to a colder climate.

Checking the coolant level

Check the condition and connections of

all cooling system hoses and heater

hoses. Replace any swollen or deterio-

rated hoses.

The coolant level should be filled

between F and L marks on the side of the

coolant reservoir when the engine is

cool.

If the coolant level is low, add enough

specified coolant to provide protection

against freezing and corrosion. Bring the

level to F, but do not overfill. If frequent

additions are required, see an authorized

Kia dealer for a cooling system inspec-

tion.

WARNING - Removing

radiator cap

• Never attempt to remove the radi-

ator cap while the engine is oper-

ating or hot. Doing so might lead

to cooling system and engine

damage and could result in seri-

ous personal injury from escap-

ing hot coolant or steam.

(Continued)

• Turn the engine off and wait until

it cools down. Use extreme care

when removing the radiator cap.

Wrap a thick towel around it, and

turn it counterclockwise slowly to

the first stop. Step back while the

pressure is released from the

cooling system. When you are

sure all the pressure has been

released, press down on the cap,

using a thick towel, and continue

turning counterclockwise to

remove it.

• Even if the engine is not operat-

ing, do not remove the radiator

cap or the drain plug while the

engine and radiator are hot. Hot

coolant and steam may still blow

out under pressure, causing seri-

ous injury.

1JBA7002

Maintenance

127

Engine coolant

Have coolant changed by an authorized

Kia dealer according to the Maintenance

Schedule at the beginning of this section.

• Use only soft (de-mineralized) water in

the coolant mixture.

• The engine in your vehicle has alu-

minum engine parts and must be pro-

tected by an ethylene-glycol-based

coolant to prevent corrosion and freez-

ing.

• DO NOT USE alcohol or methanol

coolant or mix them with the specified

coolant.

• Do not use a solution that contains

more than 60% antifreeze or less than

35% antifreeze, which would reduce

the effectiveness of the solution.

For mixture percentage, refer to the fol-

lowing table.

1JBA7003

WARNING - Radiator cap

Do not remove the radiator cap

when the engine and radiator are

hot. Scalding hot coolant and steam

may blow out under pressure caus-

ing serious injury.

-15°C (5°F) 35 65

-25°C (-13°F) 40 60

-35°C (-31°F) 50 50

-45°C (-49°F) 60 40

Ambient

Temperature

Mixture Percentage (volume)

Coolant

Solution

Water

7 13

Maintenance

BRAKE FLUID (IF EQUIPPED)

Checking brake fluid level

Check the fluid level in the reservoir peri-

odically. The fluid level should be

between MAX and MIN marks on the

side of the reservoir.

Before removing the reservoir cap and

adding brake fluid, clean the area around

the reservoir cap thoroughly to prevent

brake fluid contamination.

If your vehicle is equipped with a manual

transaxle, brake fluid is used as clutch

fluid.

If the level is low, add fluid to the MAX

level. The level will fall with accumulated

mileage. This is a normal condition asso-

ciated with the wear of the brake linings.

If the fluid level is excessively low, have

the brake system checked by an author-

ized Kia dealer.

Use only the specified brake fluid. (Refer

to “Recommended Lubricants” later in

this section.)

Never mix different types of fluid.

✽✽

NOTICE

Do not allow br ake fluid to contact the

vehicle's body paint, as paint damage

will result. Br ake fluid, which has been

exposed to open air for an extended time

should never be used as its quality can-

not be guar anteed. It should be thrown

out. Don't put in the wrong kind of fluid.

A few drops of miner al-based oil, such

as engine oil, in your br ake/clutch sys-

tem can damage brake/clutch system

par ts.

WARNING - Brake fluid

When changing and adding brake

fluid, handle it carefully. Do not let it

come in contact with your eyes. If

brake fluid should come in contact

with your eyes, immediately flush

them with a large quantity of fresh

tap water. Have your eyes examined

by a doctor as soon as possible.

WARNING - Loss of brake

fluid

In the event the brake system

requires frequent additions of fluid,

the vehicle should be inspected by

an authorized Kia dealer.

1JBA7004

Maintenance

147

DRIVE BELTS

Drive belts should be checked periodical-

ly for proper tension and adjusted if nec-

essary. At the same time, belts should be

examined for cracks, wear, fraying or

other evidence of deterioration and

replaced if necessary.

Belt routing should also be checked to be

sure there is no interference between the

belts and other parts of the engine. After

a belt is replaced, the new belt should be

adjusted again after two or three weeks

to eliminate slack resulting from initial

stretching after use.

Checking the compressor drive

belt

Have the drive belts checked in accor-

dance with the maintenance schedule.

Checking the power steering fluid

level

With the vehicle on level ground, check

the fluid level in the power steering reser-

voir periodically. The fluid should be

between MAX and MIN marks on the

side of the reservoir at the normal tem-

perature.

Before adding power steering fluid, thor-

oughly clean the area around the reser-

voir cap to prevent power steering fluid

contamination.

If the level is low, add fluid to the MAX

level.

In the event the power steering system

requires frequent addition of fluid, the

vehicle should be inspected by an

authorized Kia dealer.

✽✽

NOTICE

• To avoid damage to the power steer -

ing pump, do not operate the vehicle

for prolonged per iods with a low

power steer ing fluid level.

• Never start the engine when the reser -

voir tank is empty.

• When adding fluid, be careful that

dir t does not get into the tank.

• Insufficient fluid can result in

increased steering effor t; excessive

noise may also be pr esent as the steer -

ing wheel is tur ned.

• The use of the non-specified fluid

could reduce the effectiveness of the

power steer ing wheel and cause dam-

age to it.

Use only the specified power steering

fluid. (Refer to "Recommended

Lubricants" later in this section.)

Power steering hose

Check the hoses and hose connections

for leaks or damage before driving the

vehicle.

1JBA7005

POWER STEERING (IF EQUIPPED)

7 15

Maintenance

AUTOMATIC TRANSAXLE (IF EQUIPPED)

Checking the automatic transaxle

fluid level

The automatic transaxle fluid level

should be checked regularly.

Keep the vehicle on the level ground with

the parking brake applied and check the

fluid level according to the following pro-

cedure.

1. Place the selector lever in N (Neutral)

position and confirm the engine is run-

ning at normal idle speed.

2. After the transaxle is warmed up suffi-

ciently (fluid temperature 158~176°F

(70~80°C)), for example by 10 minutes

usual driving, shift the selector lever

through all positions then place the

selector lever in N (Neutral) or P (Park)

position.

3. Confirm that the fluid level is in “HOT”

range on the level gauge. If the fluid

level is lower, add the specified fluid

from the fill hole. If the fluid level is

higher, drain the fluid from the drain

hole.

4. If the fluid level is checked in cold con-

dition (fluid temperature 68~86°F

(20~30°C) add the fluid to “COLD” line

and then recheck the fluid level

according to the above step 2.

1JBA7006

1LDA5009

WARNING - Transaxle fluid

The transaxle fluid level should be

checked when the engine is at nor-

mal operating temperature. This

means that the engine, radiator,

radiator hose and exhaust system

etc., are very hot. Exercise great

care not to burn yourself during this

procedure.

WARNING - Parking brake

To avoid sudden movement of the

vehicle, apply parking brake and

depress the brake pedal before

moving the shift lever.

CAUTION

• Low fluid level causes transaxle

slippage. Overfilling can cause

foaming, loss of fluid and

transaxle malfunction.

• The use of a non-specified fluid

could result in transaxle malfunc-

tion and failure.

Maintenance

167

✽✽

NOTICE

“COLD” scale is for refer ence only and

should NOT be used to determine

tr ansaxle fluid level.

New automatic transaxle fluid should

be red. The red dye is added so the

assembly plant can identify it as auto-

matic transaxle fluid and distinguish it

from engine oil or antifreeze. The red

dye, which is not an indicator of fluid

quality, is not permanent. As the vehi-

cle is driven, the automatic transaxle

fluid will begin to look darker. The

color may eventually appear light

brown.

✽✽

NOTICE

Have an Author ized Kia dealer inspect

or change the automatic tr ansaxle fluid

according to the Scheduled

Maintenance at the beginning of this

section.

Checking the washer fluid level

The reservoir is translucent so that you

can check the level with a quick visual

inspection.

Check the fluid level in the washer fluid

reservoir and add fluid if necessary. Plain

water may be used if washer fluid is not

available. However, use washer solvent

with antifreeze characteristics in cold cli-

mates to prevent freezing.

LUBRICANTS AND FLUIDS

WARNING - Coolant

• Do not use radiator coolant or

antifreeze in the washer fluid

reservoir.

• Radiator coolant can severely

obscure visibility when sprayed

on the windshield and may cause

loss of vehicle control or damage

to paint and body trim.

• Windshield washer fluid agents

contain some amounts of alcohol

and can be flammable under cer-

tain circumstances. Do not allow

sparks or flame to contact the

washer fluid or the washer fluid

reservoir. Damage to the vehicle

or it's occupants could occur.

• Windshield washer fluid is poi-

sonous to humans and animals.

Do not drink and avoid contacting

windshield washer fluid. Serious

injury or death could occur.

1JBA7008

7 17

Maintenance

Body lubrication

All moving points of the body, such as

door hinges, hood hinges, and locks,

should be lubricated each time the

engine oil is changed. Use a non-freez-

ing lubricant on locks during cold weath-

er.

Make sure the engine hood secondary

latch keeps the hood from opening when

the primary latch is released.

Element cleaning

This element may be air cleaned or

replaced, depending on its condition.

Unless it is very dirty, merely shake it to

remove foreign particles. Each time this

filter is inspected, wipe the inside of the

air cleaner housing and cover with a

damp cloth. If the vehicle is operated in

extremely dusty or sandy areas, clean or

replace this element more often than at

the usual recommended intervals.

✽✽

NOTICE

Do not dr ive with the air cleaner

removed; this will r esult in excessive

engine wear.

1JBA7009

CAUTION - Engine

Driving without an air cleaner

encourages backfiring, which could

cause a fire in the engine compart-

ment.

AIR CLEANER

Maintenance

187

CLIMATE CONTROL AIR FILTER (IF EQUIPPED)

The climate control air filter installed

behind the glove box filters the dust or

other pollutants that come into the vehi-

cle from the outside through the heating

and air conditioning system. If dust or

other pollutants accumulate in the filter

over a period of time, the air flow from the

air vents may decrease, resulting in

moisture accumulation on the inside of

the windshield even when the outside

(fresh) are position is selected. If this

happens, have the climate control air fil-

ter replaced by an authorized Kia dealer.

The climate control air filter should be

replaced every 15,000 km (10,000

miles). If the vehicle is operated in the

severely air-polluted cities or on dusty

rough roads for a long period, it should

be inspected more frequently and

replaced earlier. When you try to replace

the climate control air filter by owner

maintenance, replace it performing the

following procedure, and in this case, be

careful to avoid damaging other compo-

nents.

1LDA5047

Outside air

Recirculated

air

Climate control

air filter

Blower

Evaporator

core

Heater core

7 19

Maintenance

WIPER BLADES

Wiper blade maintenance

Commercial hot waxes applied by

automatic car washes have been

known to make the windshield diffi-

cult to clean.

Contamination of either the windshield or

the wiper blades with foreign matter can

reduce the effectiveness of the wind-

shield wipers. Common sources of con-

tamination are insects, tree sap, and hot

wax treatments used by some commer-

cial car washes. If the blades are not wip-

ing properly, clean both the window and

the blades with a good cleaner or mild

detergent, and rinse thoroughly with

clean water.

✽✽

NOTICE

To prevent damage to the wiper blades,

do not use gasoline, kerosene, paint

thinner, or other solvents on or near

them.

Windshield wiper blade replace-

ment

When the wipers no longer clean ade-

quately, the blades may be worn or

cracked, and require replacement.

✽✽

NOTICE

To prevent damage to the wiper arms or

other components, do not attempt to

move the wiper s manually.

✽

NOTICE

The use of a non-specified wiper blade

could result in wiper malfunction and

failure.

1. Raise the wiper arm and turn the wiper

blade assembly to expose the plastic

locking clip.

✽✽

NOTICE

Do not allow the wiper ar m to fall

against the windshield, since it may chip

or cr ack the windshield.

1LDA5023

Maintenance

207

2. Compress the clip and slide the blade

assembly downward.

3. Lift it off the arm.

4. Install the blade assembly in the

reverse order of removal.

Rear window wiper blade

replacement (if equipped)

1. Raise the wiper arm and pull out the

wiper blade assembly.

2. Install the new blade assembly by

inserting the center part (1) into the

slot (2) in the wiper arm until it clicks

into place.

3. Make sure the blade assembly is

installed firmly by gently pulling on the

blade.

1JBA7037

1JBA7038

1JBA7048

1JBA7047

7 21

Maintenance

BATTERY

WARNING - Battery

dangers

Always read the following

instructions carefully when

handling a battery.

Keep lighted cigarettes and

all other flames or sparks

away from the battery.

Hydrogen, which is a highly

combustible gas, is always

present in battery cells and

may explode if ignited.

Keep batteries out of the

reach of children because

batteries contain highly

corrosive SULFURIC ACID.

Do not allow battery acid to

contact your skin, eyes,

clothing or paint finish.

(Continued)

If any electrolyte gets into

your eyes, flush your eyes

with clean water for at least

15 minutes and get immedi-

ate medical attention. If

possible, continue to apply

water with a sponge or

cloth until medical attention

is received.

If electrolyte gets on your

skin, thoroughly wash the

contacted area. If you feel a

pain or a burning sensation,

get medical attention imme-

diately.

Wear eye protection when

charging or working near a

battery. Always provide

ventilation when working in

an enclosed space.

(Continued)

• When lifting a plastic-cased bat-

tery, excessive pressure on the

case may cause battery acid to

leak, resulting in personal injury.

Lift with a battery carrier or with

your hands on opposite corners.

• Never attempt to charge the bat-

tery when the battery cables are

connected.

• The electrical ignition system

works with high voltage. Never

touch these components with the

engine running or the ignition

switched on.

Failure to follow the above warn-

ings can result in serious bodily

injury or death.

Maintenance

227

For best battery service :

• Keep the battery securely mounted.

• Keep the top of the battery clean and

dry.

• Keep the terminals and connections

clean, tight, and coated with petroleum

jelly or terminal grease.

• Rinse any spilled electrolyte from the

battery immediately with a solution of

water and baking soda.

• If the vehicle is not going to be used for

an extended time, disconnect the bat-

tery cables.

Battery recharging

Your vehicle has a maintenance-free,

calcium-based battery.

• If the battery becomes discharged in a

short time (because, for example, the

headlights or interior lights were left on

while the vehicle was not in use),

recharge it by slow charging (trickle)

for 10 hours.

• If the battery gradually discharges

because of high electric load while the

vehicle is being used, recharge it at 20-

30A for two hours.

Items to be reset after the battery has

been discharged or the battery has

been disconnected.

• Clock (See Chapter 3)

• Audio (See Chapter 3)

• Sunroof (See Chapter 3)

✽✽

NOTICE

• Before per forming maintenance or

rechar ging the batter y, tur n off all

accessor ies and stop the engine.

• The negative batter y cable must be

removed fir st and installed last when

the batter y is disconnected.

1JBA7017

WARNING - Recharging

battery

When recharging the battery,

observe the following precautions:

• The battery must be removed

from the vehicle and placed in an

area with good ventilation.

(Continued)

• Do not allow cigarettes, sparks, or

flame near the battery.

• Watch the battery during charg-

ing, and stop or reduce the charg-

ing rate if the battery cells begin

gassing (boiling) violently or if

the temperature of the electrolyte

of any cell exceeds 49°C (120°F).

• Wear eye protection when check-

ing the battery during charging.

• Disconnect the battery charger in

the following order.

1. Turn off the battery charger main

switch.

2. Unhook the negative clamp from

the negative battery terminal.

3. Unhook the positive clamp from

the positive battery terminal.

7 23

Maintenance

TIRES AND WHEELS

Tire care

For proper maintenance, safety, and

maximum fuel economy, you must

always maintain recommended tire

inflation pressures and stay within

the load limits and weight distribution

recommended for your vehicle.

Recommended cold tire infla-

tion pressures

All tire pressures (including the

spare) should be checked every day

when the tires are cold. “Cold Tires”

means the vehicle has not been driv-

en for at least three hours or driven

less than 1.6 km (one mile).

Recommended pressures must be

maintained for the best ride, top vehi-

cle handling, and minimum tire wear.

All specifications (sizes and pres-

sures) can be found on a label

attached to the vehicle.

✽✽

NOTICE

• Under inflation also r esults in

excessive wear, poor handling and

reduced fuel economy. Wheel

defor mation also is possible. Keep

your tire pressures at the proper

levels. If a tire frequently needs

refilling, have it checked by an

author ized Kia dealer.

• Overinflation produces a har sh

ride, excessive wear at the center

of the tire tr ead, and a greater pos-

sibility of damage fr om road haz-

ar ds.

WARNING - Tire underin-

flation

Severe underinflation (10 psi (70

kPa) or more) can lead to severe

heat build-up, causing blowouts,

tread separation and other tire

failures that can result in the

loss of vehicle control leading to

severe injury or death. This risk

is much higher on hot days and

when driving for protracted peri-

ods at high speeds.

1JBN5007B

Maintenance

247

✽✽

NOTICE

• War m tires nor mally exceed rec-

ommended cold tire pressures by

28 to 41 kPa (4 to 6 psi). Do not

release air from warm tir es to

adjust the pressure or the tires will

be under inflated.

• Be sure to reinstall the tire infla-

tion valve caps. Without the valve

cap, dirt or moisture could get into

the valve core and cause air leak-

age. If a valve cap is missing,

install a new one as soon as possi-

ble.

Checking tire inflation pres-

sure

Check your tires once a month or

more.

Also, check the tire pressure of the

spare tire.

How to check

Use a good quality gage to check tire

pressure. You can not tell if your tires

are properly inflated simply by look-

ing at them. Radial tires may look

properly inflated even when they're

underinflated.

Check the tire's inflation pressure

when the tires are cold. - "Cold"

means your vehicle has been sitting

for at least three hours or driven no

more than 1.6 km (1 mile).

WARNING - Tire Inflation

Overinflation or underinflation

can reduce tire life, adversely

affect vehicle handling, and lead

to sudden tire failure. This could

result in loss of vehicle control

and potential injury.

CAUTION

Tire pressure

Always observe the following:

• Check tire pressure when the

tires are cold. (After vehicle

has been parked for at least

three hours or hasn't been

driven more than 1.6 km (one

mile) since startup.)

• Check the pressure of your

spare tire each time you check

the pressure of other tires.

• Never overload your vehicle.

Be careful not to overload a

vehicle luggage rack if your

vehicle is equipped with one.

• Worn, old tires can cause acci-

dents. If your tread is badly

worn, or if your tires have

been damaged, replace them.

7 25

Maintenance

Remove the valve cap from the tire

valve stem. Press the tire gage firm-

ly onto the valve to get a pressure

measurement. If the cold tire inflation

pressure matches the recommended

pressure on the tire and loading

information label, no further adjust-

ment is necessary. If the pressure is

low, add air until you reach the rec-

ommended amount.

If you overfill the tire, release air by

pushing on the metal stem in the

center of the tire valve. Recheck the

tire pressure with the tire gage. Be

sure to put the valve caps back on

the valve stems. They help prevent

leaks by keeping out dirt and mois-

ture.

Tire rotation

To equalize tread wear, it is recom-

mended that the tires be rotated

every 12,000 km (7,500 miles) or

sooner if irregular wear develops.

During rotation, check the tires for

correct balance.

When rotating tires, check for uneven

wear and damage. Abnormal wear is

usually caused by incorrect tire pres-

sure, improper wheel alignment, out-

of-balance wheels, severe braking or

severe cornering. Look for bumps or

bulges in the tread or side of tire.

Replace the tire if you find either of

these conditions. Replace the tire if

fabric or cord is visible. After rotation,

be sure to bring the front and rear tire

pressures to specification and check

lug nut tightness.

Refer to Section 8, Specifications.

Disc brake pads should be inspected

for wear whenever tires are rotated.

Rotate radial tires that have an

asymmetric tread pattern only

from front to rear and not from

right to left.

CBGQ0707A

Without a spare tire

Directional tires (if equipped)

CBGQ0707

WARNING

• Do not use the temporary

spare tire for tire rotation

• Do not mix bias ply and radial

ply tires under any circum-

stances. This may cause

unusual handling characteris-

tics that could result in death,

severe injury, or property

damage.

Maintenance

267

Tire replacement

If the tire is worn evenly, a tread wear

indicator will appear as a solid band

across the tread. This shows there is

less than 1.6 mm (1/16 inch) of tread

left on the tire. Replace the tire when

this happens.

Do not wait for the band to appear

across the entire tread before replac-

ing the tire.

Compact spare tire replace-

ment (if equipped)

A compact spare tire has a shorter

tread life than a regular size tire.

Replace it when you can see the

tread wear indicator bars on the tire.

The replacement compact spare tire

should be the same size and design

tire as the one provided with your

new Kia and should be mounted on

the same compact spare tire wheel.

The compact spare tire is not

designed to be mounted on a regular

size wheel, and the compact spare

tire wheel is not designed for mount-

ing a regular size tire.

Wheel alignment and tire

balance

The wheels on your vehicle were

aligned and balanced carefully at the

factory to give you the longest tire life

and best overall performance.

In most cases, you will not need to

have your wheels aligned again.

However, if you notice unusual tire

wear or your vehicle pulling one way

or the other, the alignment may need

to be reset.

If you notice your vehicle vibrating

when driving on a smooth road, your

wheels may need to be rebalanced.

✽✽

NOTICE

Improper wheel weights can dam-

age your vehicle's aluminum wheels.

Use only approved wheel weights.

1LDA5026

Tread wear indicator

7 27

Maintenance

Wheel replacement

When replacing the metal wheels for

any reason, make sure the new

wheels are equivalent to the original

factory units in diameter, rim width

and offset.

WARNING - Replacing

tires

• Driving on worn-out tires is

very hazardous and will

reduce braking effectiveness,

steering accuracy, and trac-

tion.

• Your vehicle is equipped with

tires designed to provide for

safe ride and handling capa-

bility. Do not use a size and

type of tire and wheel that is

different from the one that is

originally installed on your

vehicle. It can affect the safety

and performance of your vehi-

cle, which could lead to han-

dling failure or rollover and

serious injury. When replacing

the tires, be sure to equip all

four tires with the tire and

wheel of the same size, type,

tread, brand and load-carrying

capacity.

(Continued)

If you nevertheless decide to

equip your vehicle with any

tire/wheel combination not

recommended by Kia for off

road driving, you should not

use these tires for highway

driving.

• The use of any other tire size

or type may seriously affect

ride, handling, ground clear-

ance, stopping distance, body

to tire clearance, snow tire

clearance, and speedometer

reliability.

• It is best to replace all four

tires at the same time. If that is

not possible, or necessary,

then replace the two front or

two rear tires as a pair.

Replacing just one tire can

seriously affect your vehicle’s

handling.

WARNING

A wheel that is not the correct

size may adversely affect wheel

and bearing life, braking and

stopping abilities, handling

characteristics, ground clear-

ance, body-to-tire clearance,

snow chain clearance,

speedometer calibration, head-

light aim and bumper height.

Maintenance

287

Tire maintenance

In addition to proper inflation, correct

wheel alignment helps to decrease

tire wear. If you find a tire is worn

unevenly, have your dealer check the

wheel alignment.

When you have new tires installed,

make sure they are balanced. This

will increase vehicle ride comfort and

tire life. Additionally, a tire should

always be rebalanced if it is removed

from the wheel.

Tire traction

Tire traction can be reduced if you

drive on worn tires, tires that are

improperly inflated or on slippery

road surfaces. Tires should be

replaced when tread wear indicators

appear. To reduce the possibility of

losing control, slow down whenever

there is rain, snow or ice on the road.

Tire sidewall labeling

Federal law requires tire manufactur-

ers to place standardized information

on the sidewall of all tires. This infor-

mation identifies and describes the

fundamental characteristics of the

tire and also provides the tire identifi-

cation number (TIN) for safety stan-

dard certification. The TIN can be

used to identify the tire in case of a

recall.

1. Manufacturer or brand name

Manufacturer or Brand name is

shown.

2. Tire size designation

A tire’s sidewall is marked with a tire

size designation. You will need this

information when selecting replace-

ment tires for your car. The following

explains what the letters and num-

bers in the tire size designation

mean.

Example tire size designation:

(These numbers are provided as an

example only; your tire size designa-

tor could vary depending on your

vehicle.)

P185/65R14 86H

P - Applicable vehicle type (tires

marked with the prefix “P’’ are

intended for use on passenger

cars or light trucks; however, not

all tires have this marking).

185 - Tire width in millimeters.

65 - Aspect ratio. The tire’s section

height as a percentage of its

width.

R - Tire construction code (Radial).

14 - Rim diameter in inches.

I030B04JM

5,6

7 29

Maintenance

86 - Load Index, a numerical code

associated with the maximum

load the tire can carry.

H - Speed Rating Symbol. See the

speed rating chart in this section

for additional information.

Wheel size designation

Wheels are also marked with impor-

tant information that you need if you

ever have to replace one. The follow-

ing explains what the letters and

numbers in the wheel size designa-

tion mean.

Example wheel size designation:

5.5JX14

5.5 - Rim width in inches.

J - Rim contour designation.

14 - Rim diameter in inches.

Tire speed r atings

The chart below lists many of the dif-

ferent speed ratings currently being

used for passenger cars. The speed

rating is part of the tire size designa-

tion on the sidewall of the tire. This

symbol corresponds to that tire's

designed maximum safe operating

speed.

3. Checking tire life (TIN : Tire

Identification Number)

Any tires that are over 6 years, based

on the manufacturing date, tire

strength and performance, decline

with age naturally (even unused

spare tires). Therefore, the tires

(including the spare tire) should be

replaced by new ones. You can find

the manufacturing date on the tire

sidewall (possibly on the inside of the

wheel), displaying the DOT Code.

The DOT Code is a series of num-

bers on a tire consisting of numbers

and English letters. The manufactur-

ing date is designated by the last four

digits (characters) of the DOT code.

DOT : XXXX XXXX OOOO

The front part of the DOT means a

plant code number, tire size and

tread pattern and the last four num-

bers indicate week and year manu-

factured.

For example:

DOT XXXX XXXX 1605 represents

that the tire was produced in the 16th

week of 2005.

S 180 km/h (112 mph)

T 190 km/h (118 mph)

H 210 km/h (130 mph)

V 240 km/h (149 mph)

Z Above 240 km/h (149 mph)

Maximum Speed

Speed

Rating

Symbol

Maintenance

307

4. Tire ply composition and mate-

rial

The number of layers or plies of rub-

ber-coated fabric in the tire. Tire

manufacturers also must indicate the

materials in the tire, which include

steel, nylon, polyester, and others.

The letter "R" means radial ply con-

struction; the letter "D" means diago-

nal or bias ply construction; and the

letter "B" means belted-bias ply con-

struction.

5. Maximum permissible inflation

pressure

This number is the greatest amount

of air pressure that should be put in

the tire. Do not exceed the maximum

permissible inflation pressure. Refer

to the Tire and Loading Information

label for recommended inflation

pressure.

6. Maximum load rating

This number indicates the maximum

load in kilograms and pounds that

can be carried by the tire. When

replacing the tires on the vehicle,

always use a tire that has the same

load rating as the factory installed

tire.

7. Uniform tire quality grading

The following information relates to

the tire grading system developed by

the Canadian Motor Vehicle Safety

Standard (CMVSS) for grading tires

by tread wear, traction and tempera-

ture performance.

Tread wear

The tread wear grade is a compara-

tive rating based on the wear rate of

the tire when tested under controlled

conditions on a specified govern-

ment test course. For example, a tire

graded 150 would wear one-and-a-

half times as well on the government

course as a tire graded 100.

The relative performance of tires

depends upon the actual conditions

of their use. However, performance

may differ from the norm because of

variations in driving habits, service

practices and differences in road

characteristics and climate.

These grades are molded on the

side-walls of passenger vehicle tires.

The tires available as standard or

optional equipment on Kia vehicles

may vary with respect to grade.

WARNING

Tires degrade over time, even

when they are not being used.

Regardless of the remaining

tread, it is recommended that

tires generally be replaced after

six (6) years of normal service.

Heat caused by hot climates or

frequent high loading condi-

tions can accelerate the aging

process. Failure to follow this

warning can result in sudden

tire failure, which could lead to a

loss of control and an accident

involving serious injury or

death.

7 31

Maintenance

Traction - AA, A, B & C

The traction grades, from highest to

lowest, are AA, A, B and C. The

grades represent the tires ability to

stop on wet pavement as measured

under controlled conditions on spec-

ified government test surfaces of

asphalt and concrete. A tire marked

C may have poor traction perform-

ance.

Temper atur e -A, B & C

The temperature grades are A (the

highest), B and C. The grades repre-

sent the tire’s resistance to the gen-

eration of heat and its ability to dissi-

pate heat when tested under con-

trolled conditions on a specified

indoor laboratory test wheel.

Sustained high temperature can

cause the material of the tires to

degenerate and reduce tires life, and

excessive temperature can lead to

sudden tires failure. Grades A and B

represent higher levels of perform-

ance on the laboratory test wheel than

the minimum required by the law.

All season tires

Kia specifies all season tires on

some models to provide good per-

formance for use all year round,

including snowy and icy road condi-

tions. All season tires are identified

by ALL SEASON and/or M+S (Mud

and Snow) on the tire sidewall. Snow

tires have better snow traction than

all season tires and may be more

appropriate in some areas.

Summer tires

Kia specifies summer tires on some

models to provide superior perform-

ance on dry roads. Summer tire per-

formance is substantially reduced in

snow and ice. Summer tires do not

have the tire traction rating M+S

(Mud and Snow) on the tire side wall.

if you plan to operate your vehicle in

snowy or icy conditions. Kia recom-

mends the use of snow tires or all

season tires on all four wheels.

Snow tires

If you equip your car with snow tires,

they should be the same size and

have the same load capacity as the

original tires. Snow tires should be

installed on all four wheels; other-

wise, poor handling may result.

Snow tires should carry 28 kPa (4

psi) more air pressure than the pres-

sure recommended for the standard

tires on the tire label on the driver's

side of the center pillar, or up to the

maximum pressure shown on the tire

sidewall, whichever is less.

Do not drive faster than 120 km/h (75

mph) when your car is equipped with

snow tires.

WARNING - Tire

temperature

The temperature grade for this

tire is established for a tire that

is properly inflated and not

overloaded. Excessive speed,

underinflation, or excessive

loading, either separately or in

combination, can cause heat

build-up and possible sudden

tire failure. This can cause loss

of vehicle control and serious

injury or death.

Maintenance

327

LUBRICANT SPECIFICATIONS

Recommended lubricants

To help achieve proper engine and powertrain performance and

durability, use only lubricants of the proper quality. The correct

lubricants also help promote engine efficiency that results in

improved fuel economy.

Engine oils labeled Energy Conserving Oil are now available.

Along with other additional benefits, they contribute to fuel

economy by reducing the amount of fuel necessary to over-

come engine friction. Often, these improvements are difficult to

measure in everyday driving, but in a year’s time, they can offer

significant cost and energy savings.

Recommended SAE viscosity number

✽✽

NOTICE

Always be sure to clean the area around any filler plug, dr ain

plug, or dipstick before checking or dr aining any lubr icant.

This is especially impor tant in dusty or sandy areas and when

the vehicle is used on unpaved roads. Cleaning the plug and

dipstick areas will prevent dirt and gr it from entering the

engine and other mechanisms that could be damaged.

Engine oil viscosity (thickness) has an effect on fuel economy

and cold weather operating (starting and oil flow). Lower vis-

cosity engine oils can provide better fuel economy and cold

weather performance, however, higher viscosity engine oils are

required for satisfactory lubrication in hot weather. Using oils of

any viscosity other than those recommended could result in

engine damage.

When choosing an oil, consider the range of temperature your

vehicle will be operated in before the next oil change. Proceed

to select the recommended oil viscosity from the chart.

*¹ Refer to the recommended SAE viscosity numbers.

These lubricants and fluids are recommended for use in your

vehicle.

Lubricant Classification

API Service SJ, SL or above,

ILSAC GF-3 or above

Manual transaxle fluid

API Service GL-4

(SAE 75W-85, fill-for-life)

DIAMOND ATF SP-III, SK ATF SP-III

Power steering fluid PSF-III

Brake/Clutch fluid FMVSS116 DOT-3 or DOT-4

Engine oil

*¹

Automatic transaxle fluid

Temperature Range for SAE Viscosity Numbers

Temperature

Engine Oil *

°C

(°F)

-30 -20 -10 0 10 20 30 40 50

-10 0 20 40 60 80 100 120

1. For better fuel economy, it is recommended to use the engine oil of a viscosity

grade SAE 5W-20,5W-30 (API SJ, SL / ILSAC GF-3).

10W-30

5W-20, 5W-30

7 33

Maintenance

EXTERIOR CARE

Exterior general caution

It is very important to follow the label

directions when using any chemical

cleaner or polish. Read all warning and

caution statements that appear on the

label.

Finish maintenance

Washing

To help protect your vehicle’s finish from

rust and deterioration, wash it thoroughly

and frequently at least once a month with

lukewarm or cold water.

If you use your vehicle for off-road driv-

ing, you should wash it after each off-

road trip. Pay special attention to the

removal of any accumulation of salt, dirt,

mud, and other foreign materials. Make

sure the drain holes in the lower edges of

the doors and rocker panels are kept

clear and clean.

Insects, tar, tree sap, bird droppings,

industrial pollution and similar deposits

can damage your vehicle’s finish if not

removed immediately.

Even prompt washing with plain water

may not completely remove all these

deposits. A mild soap, safe for use on

painted surfaces, may be used.

After washing, rinse the vehicle thor-

oughly with lukewarm or cold water. Do

not allow soap to dry on the finish.

✽✽

NOTICE

Do not use strong soap, chemical deter -

gents or hot water, and do not wash the

vehicle in direct sunlight or when the

body of the vehicle is war m.

✽

NOTICE

• Water washing in the engine compart-

ment including high pressure water

washing may cause the failure of elec-

tr ical circuits located in the engine

compar tment.

• Never allow water or other liquids to

come in contact with electrical/elec-

tronic components inside the vehicle

as this may damage them.

WARNING - Wet brakes

After washing the vehicle, test the

brakes while driving slowly to see if

they have been affected by water. If

braking performance is impaired,

dry the brakes by applying them

lightly while maintaining a slow for-

ward speed.

OJB037800

Maintenance

347

Waxing

Wax the vehicle when water will no

longer bead on the paint.

Always wash and dry the vehicle before

waxing. Use a good quality liquid or

paste wax, and follow the manufacturer’s

instructions. Wax all metal trim to protect

it and to maintain its luster.

Removing oil, tar, and similar materials

with a spot remover will usually strip the

wax from the finish. Be sure to re-wax

these areas even if the rest of the vehicle

does not yet need waxing.

✽✽

NOTICE

• Wiping dust or dir t off the body with

a dr y cloth will scr atch the finish.

• Do not use steel wool, abrasive clean-

ers, or strong deter gents containing

highly alkaline or caustic agents on

chrome-plated or anodized aluminum

par ts. This may result in damage to

the protective coating and cause dis-

coloration or paint deterior ation.

Finish damage repair

Deep scratches or stone chips in the

painted surface must be repaired

promptly. Exposed metal will quickly rust

and may develop into a major repair

expense.

✽✽

NOTICE

If your vehicle is damaged and r equires

any metal repair or replacement, be sure

the body shop applies anti-cor r osion

materials to the par ts repaired or

replaced.

Bright-metal maintenance

• To remove road tar and insects, use a

tar remover, not a scraper or other

sharp object.

• To protect the surfaces of bright-metal

parts from corrosion, apply a coating of

wax or chrome preservative and rub to

a high luster.

• During winter weather or in coastal

areas, cover the bright metal parts with

a heavier coating of wax or preserva-

tive. If necessary, coat the parts with

non-corrosive petroleum jelly or other

protective compound.

Underbody maintenance

Corrosive materials used for ice and

snow removal and dust control may col-

lect on the underbody. If these materials

are not removed, accelerated rusting can

occur on underbody parts such as the

fuel lines, frame, floor pan and exhaust

system, even though they have been

treated with rust protection.

Thoroughly flush the vehicle underbody

and wheel openings with lukewarm or

cold water once a month, after off-road

driving and at the end of each winter. Pay

special attention to these areas because

it is difficult to see all the mud and dirt. It

will do more harm than good to wet down

the road grime without removing it. The

lower edges of doors, rocker panels, and

frame members have drain holes that

should not be allowed to clog with dirt;

trapped water in these areas can cause

rusting.

WARNING

After washing the vehicle, test the

brakes while driving slowly to see if

they have been affected by water. If

braking performance is impaired,

dry the brakes by applying them

lightly while maintaining a slow for-

ward speed.

7 35

Maintenance

Aluminum wheel maintenance

The aluminum wheels are coated with a

clear protective finish.

• Do not use any abrasive cleaner, pol-

ishing compound, solvent, or wire

brushes on aluminum wheels. They

may scratch or damage the finish.

• Use only a mild soap or neutral deter-

gent, and rinse thoroughly with water.

Also, be sure to clean the wheels after

driving on salted roads. This helps pre-

vent corrosion.

• Avoid washing the wheels with high-

speed car wash brushes.

• Do not use any acid detergent. It may

damage and corrode the aluminum

wheels coated with a clear protective

finish.

INTERIOR CARE

Interior general precautions

Prevent caustic solutions such as per-

fume and cosmetic oil from contacting

the dashboard because they may cause

damage or discoloration. If they do con-

tact the dashboard, wipe them off imme-

diately. See the instructions that follow for

the proper way to clean vinyl.

✽✽

NOTICE

Never allow water or other liquids to

come in contact with electrical/electron-

ic components inside the vehicle as this

may damage them.

Cleaning the upholstery and inte-

rior trim

Vinyl

Remove dust and loose dirt from vinyl

with a whisk broom or vacuum cleaner.

Clean vinyl surfaces with a vinyl cleaner.

Fabric

Remove dust and loose dirt from fabric

with a whisk broom or vacuum cleaner.

Clean with a mild soap solution recom-

mended for upholstery or carpets.

Remove fresh spots immediately with a

fabric spot cleaner. If fresh spots do not

receive immediate attention, the fabric

can be stained and its color can be

affected. Also, its fire-resistant properties

can be reduced if the material is not

properly maintained.

✽✽

NOTICE

Using anything but r ecommended

cleaner s and pr ocedures may affect the

fabr ic’s appear ance and fir e-resistant

proper ties.

Maintenance

367

Cleaning the lap/shoulder belt

webbing

Clean the belt webbing with any mild

soap solution recommended for cleaning

upholstery or carpet. Follow the instruc-

tions provided with the soap. Do not

bleach or re-dye the webbing because

this may weaken it.

Cleaning the interior window

glass

If the interior glass surfaces of the vehi-

cle become fogged (that is, covered with

an oily, greasy or waxy film), they should

be cleaned with glass cleaner. Follow the

directions on the glass cleaner container.

✽✽

NOTICE

Do not scr ape or scratch the inside of

the rear window. This may r esult in

damage to the r ear window defroster

grid.

Maintenance for Your Kia Rio 4 Door Second Generation (2006-2010)

Related Topics

Popular Owner Manuals

Latest Owner Manuals