Get Specifications, Consumer information and Reporting safety defects -> Recommended lubricants and capacities Guide for Kia Sorento SUV Third Generation (2016-2020)

Features of your vehicle

✽

NOTICE

For non rolling code garage door

openers, follow steps 2 - 3.

NOTICE

Flashing

Some gate and garage door openers

may require you to replace step #3

with the “cycling” procedure noted

in the “Canadian Programming”

section of this document.

For rolling code garage door open-

ers, follow steps 2 - 6.

For Canadian Programming, please

follow the Canadian Programming

section.

For help with determining whether

your

garage

door

opener

non-rolling code or rolling code,

please refer to the garage door open-

Transmitter

OHD046307N

ers

owner’s

manual

contact

2. Press and hold the button on the

HomeLink system you wish to

train and the button on the trans-

mitter while the transmitter is

approximately 2-8 cm (1 to 3 inch-

es) away from the mirror. Do not

release the buttons until step 3

has been completed.

HomeLink customer service at 1-

800-355-3515.

3. The HomeLink indicator light will

flash, first slowly and then rapidly.

When the indicator light flashes

rapidly, both buttons may be

released. (The rapid flashing light

indicates successful programming

of the new frequency signal.)

4 65

Features of your vehicle

Rolling code programming

6. Return to the vehicle and firmly Operating HomeLink

press and release the pro-

To train a garage door opener (or

other rolling code equipped devices)

with the rolling code feature, follow

these instructions after completing

the “Programming” portion of this

text. (A second person may make the

following training procedures quicker

& easier.)

To operate, simply press the

grammed HomeLink button up to

three times. The rolling code

equipped device should now rec-

ognize the HomeLink signal and

activate when the HomeLink but-

ton is pressed. The remaining two

buttons may now be programmed

if this has not previously been

done. Refer to the “Programming”

portion of this text.

programmed HomeLink button.

Activation will now occur for the

trained product (garage door, securi-

ty system, entry door lock, estate

gate, or home or office lighting). For

convenience, the hand-held trans-

mitter of the device may also be used

at any time. The HomeLink Wireless

Controls System (once programmed)

or the original hand-held transmitter

may be used to activate the device

(e.g. garage door, entry door lock,

etc.). In the event that there are still

programming difficulties, contact

HomeLink at 1-800-355-3515 or on

the internet at www.homelink.com.

4. Locate the “learn” or “smart” but-

ton on the device’s motor head

unit. Exact location and color of

the button may vary by product

brand. If there is difficulty locating

the “learn” or “smart” button, refer-

ence the device’s owner’s manual

or contact HomeLink at 1-800-

355-3515 or on the internet at

www.homelink.com.

5. Press and release the “learn” or

“smart” button on the device’s

motor head unit. You have 30 sec-

onds to complete step number 6.

4 66

Features of your vehicle

Erasing programmed HomeLink Reprogramming a single

buttons HomeLink button

Canadian Programming

Garage & gate openers

To program a device to HomeLink During programming, your hand-held

using a HomeLink button previously transmitter may automatically stop

Flashing

trained, follow these steps:

transmitting. Continue to press and

hold the HomeLink button (note

1. Press and hold the desired

HomeLink button. Do NOT release

until step 4 has been completed.

steps

through

in the

“Programming” portion of this text)

while you press and re-press

(“cycle”) your handheld transmitter

every two seconds until the frequen-

cy signal has been learned. The indi-

cator light will flash slowly and then

rapidly after several seconds upon

successful training.

2. When the indicator light begins to

flash slowly (after 20 seconds),

position the hand-held transmitter

2-8 cm (1 to 3 inches) away from

the HomeLink surface.

OHD046306N

3. Press and hold the hand-held

transmitter button (or press and

“cycle” - as described in “Canadian

Programming”).

To erase the three programmed but-

tons (individual buttons cannot be

erased):

4. The HomeLink indicator light will

flash, first slowly and then rapidly.

When the indicator light begins to

flash rapidly, release both buttons.

• Press and hold the left and center

buttons simultaneously, until the

indicator light begins to flash

(approximately 20 seconds).

Release both buttons. Do not hold The previous device has now been

for longer than 30 seconds.

erased and the new device can be

activated by pushing the HomeLink

button that has just been pro-

grammed. This procedure will not

affect any other programmed

HomeLink buttons.

HomeLink is now in the train (or

learning) mode and can be pro-

grammed at any time.

4 67

Specifications, Consumer information and Reporting safety defects -> Recommended lubricants and capacities for Your Kia Sorento SUV Third Generation (2016-2020)

Related Topics

Popular Owner Manuals

Latest Owner Manuals