2024-2026 Lexus LBX SUV For safety and security -> Child safety User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

For safety and security -> Child safety for Your Lexus LBX SUV First Generation (2024-2026)

48
1-2. Child safety
1-2.Chil d safety
Left-hand drive vehicles
“PASSENGER AIR BAG” indica-
tor
“PASSENGER AIR BAG” and “ON” indi-
cator lights turn on when the airbag system
is on, and about after 60 seconds they go
off (only when the power switch is in ON).
Airbag manual on-off switch
Right-hand drive vehicles
“PASSENGER AIR BAG” indica-
tor
“PASSENGER AIR BAG” and “ON” indi-
cator lights turn on when the airbag system
is on, and about after 60 seconds they go
off (only when the power switch is in ON).
Airbag manual on-off switch
Insert the mechanical key into the cyl-
inder and turn to the “OFF” position.
The “OFF” indicator light turns on (only
when the power switch is in ON).
Airbag manual on-off system
This system deactivates the follow-
ing SRS airbags:
SRS front passenger airbag
Only deactivate the airbags when
using a child restraint system on the
front passenger seat.
System components
A
B
Deactivating the airbags for the
front passenger
A
B
49
1
1-2. Child safety
For safety and security
■ “PASSENGER AIR BAG” indicator
information
If any of the following problems occur, it is
possible that there is a malfunction in the
system. Have the vehicle inspected by any
authorized Lexus retailer or Lexus autho-
rized repairer, or any reliable repairer.
● The “OFF” indicator does not illuminate
when the airbag manual on-off switch is
set to “OFF”.
● The indicator light does not change when
the airbag manual on-off switch is
switched to “ON” or “OFF”.
WARNING
■ When installing a child restraint sys-
tem
For safety reasons, always install a child
restraint system in a rear seat. In the
event that the rear seat cannot be used,
the front seat can be used as long as the
airbag manual on-off system is set to
“OFF”.
If the airbag manual on-off system is left
on, the strong impact of the airbag
deployment (inflation) may cause serious
injury or even death.
■ When a child restraint system is not
installed on the front passenger seat
Ensure that the airbag manual on-off sys-
tem is set to “ON”.
If it is left off, the airbag may not deploy in
the event of an accident, which may
result in serious injury or even death.
Riding with children
Observe the following precautions
when children are in the vehicle.
Use a child restraint system appro-
priate for the child, until the child
becomes large enough to properly
wear the vehicle’s seat belt.
It is recommended that children
sit in the rear seats to avoid acci-
dental contact with the shift lever,
wiper switch, etc.
Use the rear door child-protector
lock or the window lock switch to
avoid children opening the door
while driving or operating the
power window accidentally.
(P.137, 167)
Do not let small children operate
equipment which may catch or
pinch body parts, such as the
power window, hood, back door,
seats, etc.
WARNING
■ When children are in the vehicle
Never leave children unattended in the
vehicle, and never allow children to have
or use the key.
Children may be able to start the vehicle
or shift the vehicle into neutral. There is
also a danger that children may injure
themselves by playing with the windows
or other features of the vehicle. In addi-
tion, heat build-up or extremely cold
temperatures inside the vehicle can be
fatal to children.
50
1-2. Child safety
Points to remember: P.50
When using a child restraint system:
P.51
Child restraint system compatibility for
each seating position: P.54
Child restraint system installation
method: P.60
• Fixed with a seat belt: P.61
• Fixed with an ISOFIX lower anchor-
age: P.63
• Using a top tether anchorage: P.64
Prioritize and observe the warnings,
as well as the laws and regulations
for child restraint systems.
Use a child restraint system until the
child becomes large enough to
properly wear the vehicle’s seat
belt.
Choose a child restraint system
appropriate to the age and size of
the child.
Note that not all child restraint sys-
tems can fit in all vehicles.
Before using or purchasing a child
restraint system, check the compati-
bility of the child restraint system
with seat positions.
Child restraint systems
Before installing a child restraint
system in the vehicle, there are pre-
cautions that need to be observed,
different types of child restraint sys-
tems, as well as installation meth-
ods, etc., written in this manual.
Use a child restraint system when
riding with a small child that can-
not properly use a seat belt. For
the child’s safety, install the child
restraint system to a rear seat. Be
sure to follow the installation
method that is in the operation
manual enclosed with the
restraint system.
The use of a Lexus genuine child
restraint system is recommended,
as it is safer to use in this vehicle.
Lexus genuine child restraint sys-
tems are made specifically for
Lexus vehicles. They can be pur-
chased at a Lexus dealer.
Table of contents
Points to remember
WARNING
■ When a child is riding
Observe the following precautions.
Failure to do so may result in death or
serious injury.
● For effective protection in automobile
accidents and sudden stops, a child
must be properly restrained, using a
seat belt or child restraint system
which is correctly installed. For instal-
lation details, refer to the operation
manual enclosed with the child
restraint system. General installation
instruction is provided in this manual.
51
1
1-2. Child safety
For safety and security
■ When installing a child restraint
system to the front passenger seat
For the safety of a child, install a child
restraint system to a rear seat. When
installing a child restraint system to the
front passenger seat is unavoidable,
adjust the seat as follows and install the
child restraint system:
Adjust the seatback angle to the
most upright position.
When installing a forward-facing child
seat, if there is a gap between the child seat
and the seatback, adjust the seatback
angle until good contact is achieved.
Move the front seat fully rearward.
Adjust the seat height to the upper-
most position.
If the head restraint interferes with
the child restraint system installation
and the head restraint can be
removed, remove the head
restraint. Otherwise, put the head
restraint in the upper most position.
WARNING
● Lexus strongly urges the use of a
proper child restraint system that con-
forms to the weight and size of the
child, installed on the rear seat.
According to accident statistics, the
child is safer when properly restrained
in the rear seat than in the front seat.
● Holding a child in your or someone
else’s arms is not a substitute for a child
restraint system. In an accident, the
child can be crushed against the wind-
shield or between the holder and the
interior of the vehicle.
■ Handling the child restraint system
If the child restraint system is not prop-
erly fixed in place, the child or other pas-
sengers may be seriously injured or even
killed in the event of sudden braking,
sudden swerving, or an accident.
● If the vehicle were to receive a strong
impact from an accident, etc., it is pos-
sible that the child restraint system has
damage that is not readily visible. In
such cases, do not reuse the restraint
system.
● Depending on the child restraint sys-
tem, installation may be difficult or
impossible. In those cases, check
whether the child restraint system is
suitable for installment in the vehicle.
(P.54) Be sure to install and
observe the usage rules after carefully
reading the child restraint system fix-
ing method in this manual, as well as
the operation manual enclosed with
the child restraint system.
● Keep the child restraint system prop-
erly secured on the seat even if it is not
in use. Do not store the child restraint
system unsecured in the passenger
compartment.
● If it is necessary to detach the child
restraint system, remove it from the
vehicle or store it securely in the lug-
gage compartment.
When using a child restraint sys-
tem
52
1-2. Child safety
WARNING
■ When using a child restraint system
Observe the following precautions.
Failure to do so may result in death or
serious injury.
● Never use a rear-facing child restraint
system on the front passenger seat
when the airbag manual on-off switch
is on. (P.48)
The force of the rapid inflation of the
front passenger airbag can cause
death or serious injury to children in
the event of an accident.
● There is a label(s) on the passenger
side sun visor, indicating it is forbidden
to attach a rear-facing child restraint
system to the front passenger seat.
Details of the label(s) are shown in the
illustration below.
53
1
1-2. Child safety
For safety and security
WARNING
WARNING
● Only put a forward-facing child
restraint system on the front seat when
unavoidable. When installing a for-
ward-facing child restraint on the front
passenger seat, move the seat as far
back as possible. Failing to do so may
result in death or serious injury if the
airbags deploy (inflate).
● Do not allow the child to lean his/her
head or any part of his/her body
against the door or the area of the seat,
front or rear pillars, or roof side rails
from which the SRS side airbags or
SRS curtain shield airbags deploy even
if the child is seated in the child
restraint system. It is dangerous if the
SRS side and curtain shield airbags
inflate, and the impact could cause
death or serious injury to the child.
● When a junior seat is installed, always
ensure that the shoulder belt is posi-
tioned across the center of the child’s
shoulder. The belt should be kept away
from the child’s neck, but not so that it
could fall off the child’s shoulder.
● Use a child restraint system suitable to
the age and size of the child and install
it to the rear seat.
54
1-2. Child safety
■ Child restraint system compatibil-
ity for each seating position
Compatibility of each seating position
with child restraint systems (P.55)
displays the type of child restraint sys-
tems that can be used and possible
seating positions for installation using
symbols.
Also, the recommended child restraint
system that is suitable for your child
can be selected. Otherwise, check
“Recommended child restraint sys-
tems information” for recommended
child restraint systems. (P.59)
Check the selected child restraint sys-
tem together with the following
“Before confirming the compatibility of
each seating position with child
restraint systems”.
■ Before confirming the compatibil-
ity of each seating position with
child restraint systems
1 Check the child restraint system
standards.
Use a child restraint system that
conforms to UN(ECE) R44
*1
or
UN(ECE) R129
*1, 2
.
The following approval mark is dis-
played on child restraint systems
which are conformed.
Check for an approval mark
attached to the child restraint sys-
tem.
Example of the displayed regulation Num-
ber
UN(ECE) R44 approval mark
*3
The weight range of the child who is
applicable for an UN(ECE) R44
approval mark is indicated.
UN(ECE) R129 approval mark
*3
The height range of the child who is
applicable as well as available
weights for an UN(ECE) R129
approval mark is indicated.
WARNING
● If the driver’s seat interferes with the
child restraint system and prevents it
from being attached correctly, attach
the child restraint system to the right-
hand rear seat (left-hand drive vehi-
cles) or the left-hand rear seat (right-
hand drive vehicles).
Child restraint system compati-
bility for each seating position
A
B
55
1
1-2. Child safety
For safety and security
2 Check the category of the child
restraint system.
Check the approval mark of the
child restraint system for which of
the following categories the child
restraint system is suitable.
Also, if there are any uncertainties,
check the user’s guide included
with the child restraint system or
contact the retailer of the child
restraint system.
• “universal”
• “semi-universal”
• “restricted”
• “vehicle specific”
*1
: UN(ECE) R44 and UN(ECE) R129
are U.N. regulations for child restraint
systems.
*2
: The child restraint systems mentioned
in the table may not be available outside
of the EU area.
*3
: The displayed mark may differ depend-
ing on the product.
■ Compatibility of each seating posi-
tion with child restraint systems
Left-hand drive vehicles
Right-hand drive vehicles
Deactivation of front passenger
airbag.
Activation of front passenger air-
bag.
Never use a rearward-facing child
restraint system on the front pas-
senger seat when the airbag man-
ual on-off switch is on.
56
1-2. Child safety
*1
: Move the front seat fully rearward. If the
passenger seat height can be adjusted,
move it to the upper most position.
*2
: Adjust the seatback angle to the most
upright position. When installing a for-
ward-facing child seat, if there is a gap
between the child seat and the seat-
back, adjust the seatback angle until
good contact is achieved.
*3
: If the head restraint interferes with your
child restraint system, and the head
restraint can be removed, remove the
head restraint.
Otherwise, put the head restraint in the
upper most position.
*4
: Applicable for KIDFIX i-SIZE only.
*5
: Not suitable for child restraint systems
with support leg.
*6
: Move the armrest fully forward.
When securing some types of child
restraint systems in rear seat, it may not
be possible to properly use the seat
belts in positions next to the child
restraint without interfering with it or
affecting seat belt effectiveness. Be
sure your seat belt fits snugly across
your shoulder and low on your hips. If it
does not, or if it interferes with the child
restraint, move to a different position.
Failure to do so may result in death or
serious injury.
When installing a child restraint in
the rear seats, adjust the front seat
so that it does not interfere with the
child or child restraint system.
When installing a child seat with
support base, if the child seat inter-
feres with the seatback when latch-
ing it into the support base, adjust
the seatback rearward until there is
no interference.
If the seat belt shoulder anchor is
ahead of the child seat belt guide,
move the seat cushion forward.
Suitable for “universal” category
child restraint system fixed with
the seat belt.
Suitable for forward-facing “uni-
versal” category child restraint
system fixed with the seat belt.
Suitable for recommended child
restraint systems given on recom-
mended child restraint systems
information. (P.59)
Suitable for i-Size and ISOFIX
child restraint system.
Includes a top tether anchorage
point.
57
1
1-2. Child safety
For safety and security
When installing a junior seat, if the
child in your child restraint system is
in a very upright position, adjust the
seatback angle to the most comfort-
able position. And if the seat belt
shoulder anchor is ahead of the
child seat belt guide, move the seat
cushion forward.
■ Detail information for child restraint systems installation
*1
: All universal categories (group 0, 0+, I,
II and III).
*2
: Not suitable for child restraint systems
with support leg.
Seating position
Seat position number
*2
Airbag manual on-off
switch
ON OFF
Seating position suitable
for universal belted
(Yes/No)
*1
Yes
Forward-
facing only
Yes Yes Yes Yes
i-Size seating position
(Yes/No)
No No Yes No Yes
Seating position suitable
for lateral fixture
(L1/L2/No)
No No No No No
Suitable rearward facing
fixture
(R1/R2X/R2/R3/No)
No No
R1, R2X,
R2, R3
*3
No
R1, R2X,
R2, R3
*4
Suitable forward facing
fixture (F2X/F2/F3/No)
No No
F2X, F2,
F3
No
F2X, F2,
F3
Suitable junior seat fix-
ture (B2/B3/No)
B2, B3
Belt fixa-
tion only
B2, B3
Belt fixa-
tion only
B2, B3 No B2, B3
58
1-2. Child safety
*3
: Adjust the driver’s seat to the highest
position. (P.154)
*4
: Before installing a child restraint system
to this seat, adjust the position of the
front passenger’s seat to between the
1st lock position and 12th lock position
(16th lock position from the rear).
1st lock position
12th lock position
Lexus suggests the users to use and seating positions.
ISOFIX child restraint systems are divided into different “fixture”. The child
restraint system can be used in the seating positions for “fixture” mentioned in the
table above. For kind of “fixture” relation, confirm the following table.
If your child restraint system has no kind of “fixture” (or if you cannot find informa-
tion in the table below), please refer to the child restraint system “vehicle list” for
compatibility information or ask the retailer of your child seat.
A
B
Mass
group
Child weight
Size
class
Fix-
ture
Description
0
up to 10 kg
(22 lb.)
E R1 Rearward-facing infant seat
F L1 Left lateral-facing infant seat (Carrycot)
G L2 Right lateral-facing infant seat (Carrycot)
0+
up to 13 kg
(28 lb.)
C R3 Full-size, rearward-facing child restraint systems
D R2
Reduced-size, rearward-facing child restraint sys-
tems
R2X
Reduced-size, rearward-facing child restraint sys-
tems
E R1 Rearward-facing infant seat
59
1
1-2. Child safety
For safety and security
■ Recommended child restraint systems information
*1
: Be sure to attach the seat belt through the SecureGuard.
*2
: LEXUS recommends to use with lower anchorages.
The child restraint systems mentioned in the table may not be available outside the
EU countries and United Kingdom.
I
9 to 18 kg (20
to 39 lb.)
A F3 Full-height, forward-facing child restraint systems
B F2
Reduced-height, forward-facing child restraint sys-
tems
B1 F2X
Reduced-height, forward-facing child restraint sys-
tems
C R3 Full-size, rearward-facing child restraint systems
D R2
Reduced-size, rearward-facing child restraint sys-
tems
II
15 to 25 kg
(34 to 55 lb.)
B2,
B3
Junior seat
III
22 to 36 kg
(48 to 79 lb.)
Recommended
child restraint
system
Size
Direction of
travel
Fixation
fixed with lower
anchorages
fixed with a seat
belt
MAXI COSI
PEARL 360 &
FAMILYFIX
360 BASE
40 to 105 cm
Rearward-facing
Yes Not applicable
Up to 17.5 kg
(Up to 38 lb.)
>15 month &
76 to 105 cm
Forward-facing
Up to 17.5 kg
(Up to 38 lb.)
LEXUS
KIDFIX
i-SIZE
*1, 2
100 to 150 cm
Forward-facing
use only
Yes Yes
15 to 36 kg
(34 to 79 lb.)
Mass
group
Child weight
Size
class
Fix-
ture
Description
60
1-2. Child safety
When using the child restraint sys-
tem with SecureGuard, be sure to
guide the lap belt into SecureGuard
as shown in the illustration.
Confirm with the operation manual enclosed with the child restraint system about
the installation of the child restraint system.
A
Child restraint system installation method
Installation method Page
Seat belt attachment P.61
61
1
1-2. Child safety
For safety and security
■ Installing child restraint system
using a seat belt
Install the child restraint system in
accordance to the operation manual
enclosed with the child restraint sys-
tem.
If the child restraint system on hand is
not within the “universal” category (or
the necessary information is not in the
table), refer to the “Vehicle List” pro-
vided by the child restraint system
maker for various possible installation
positions, or check the compatibility
after asking the retailer of the child
seat. (P.54)
1 If installing the child restraint sys-
tem to the front passenger seat is
unavoidable, refer to P.51 for front
passenger seat adjustment.
2 If the head restraint interferes with
the child restraint system and the
head restraint can be removed,
remove the head restraint. Other-
wise, put the head restraint in the
upper most position. (P.157)
3 Run the seat belt through the child
restraint system and insert the plate
into the buckle. Make sure that the
belt is not twisted. Securely fix the
seat belt to the child restraint sys-
tem in accordance to the directions
ISOFIX lower anchorage
attachment
P.63
Top tether anchorage
attachment
P.64
Installation method Page
Child restraint system fixed with
a seat belt
62
1-2. Child safety
enclosed with the child restraint
system.
4 If your child restraint system is not
equipped with a lock-off (a seat belt
locking feature), secure the child
restraint system using a locking
clip.
5 After installing the child restraint
system, rock it back and forth to
ensure that it is installed securely.
(P.62)
■ Removing a child restraint system
installed with a seat belt
Press the buckle release button and
fully retract the seat belt.
When releasing the buckle, the child
restraint system may spring up due to the
rebound of the seat cushion. Release the
buckle while holding down the child
restraint system.
Since the seat belt automatically reels itself,
slowly return it to the stowing position.
■ When installing a child restraint system
You may need a locking clip to install the
child restraint system. Follow the instruc-
tions provided by the manufacturer of the
system. If your child restraint system does
not provide a locking clip, you can purchase
the following item from any authorized
Lexus retailer or Lexus authorized repairer,
or any reliable repairer: Locking clip for
child restraint system
(Part No. 73119-22010)
WARNING
■ When installing a child restraint sys-
tem
Observe the following precautions.
Failure to do so may result in death or
serious injury.
● Do not allow children to play with the
seat belt. If the seat belt becomes
twisted around a child’s neck, it may
lead to choking or other serious inju-
ries that could result in death. If this
occurs and the buckle cannot be
unfastened, scissors should be used to
cut the belt.
● Ensure that the belt and plate are
securely locked and the seat belt is not
twisted.
● Shake the child restraint system left
and right, and forward and backward
to ensure that it has been securely
installed.
● After securing a child restraint system,
never adjust the seat.
● When a junior seat is installed, always
ensure that the shoulder belt is posi-
tioned across the center of the child’s
shoulder. The belt should be kept away
from the child’s neck, but not so that it
could fall off the child’s shoulder.
63
1
1-2. Child safety
For safety and security
■ ISOFIX lower anchorages (ISO-
FIX child restraint system)
Lower anchorages are provided for
the outboard rear seats. (Marks dis-
playing the location of the anchorages
are attached to the seats.)
■ Installation with ISOFIX lower
anchorage (ISOFIX child restraint
system)
Install the child restraint system in
accordance to the operation manual
enclosed with the child restraint sys-
tem.
If the child restraint system on hand is
not within the “universal” category (or
the necessary information is not in the
table), refer to the “Vehicle List” pro-
vided by the child restraint system
maker for various possible installation
positions, or check the compatibility
after asking the retailer of the child
seat. (P.54)
1 If the head restraint interferes with
the child restraint system and the
head restraint can be removed,
remove the head restraint. Other-
wise, put the head restraint in the
upper most position. (P.157)
2 Remove the anchorage covers, and
install the child restraint system to
the seat.
The bars are installed behind the anchor-
age covers.
3 After installing the child restraint
system, rock it back and forth to
ensure that it is installed securely.
(P.62)
WARNING
● Follow all installation instructions pro-
vided by the child restraint system
manufacturer.
Child restraint system fixed with
an ISOFIX lower anchorage
WARNING
■ When installing a child restraint sys-
tem
Observe the following precautions.
Failure to do so may result in death or
serious injury.
● After securing a child restraint system,
never adjust the seat.
64
1-2. Child safety
■ Top tether anchorages
Top tether anchorages are provided
for the outboard rear seats.
Use top tether anchorages when fixing
the top strap.
Top tether anchorages
Top strap
■ Fixing the top strap to the top
tether anchorage
Install the child restraint system in
accordance to the operation manual
enclosed with the child restraint sys-
tem.
1 If the head restraint interferes with
the child restraint system and the
head restraint can be removed,
remove the head restraint. Other-
wise, put the head restraint in the
upper most position. (P.157)
2 Latch the hook onto the top tether
anchorage and tighten the top
strap.
Make sure the top strap is securely
latched. (P.62)
When installing the child restraint system
with the head restraint raised, be sure to
have the top strap pass underneath the
head restraint.
Top strap
Hook
WARNING
● When using the lower anchorages, be
sure that there are no foreign objects
around the anchorages and that the
seat belt is not caught behind the child
restraint system.
● Follow all installation instructions pro-
vided by the child restraint system
manufacturer.
Using a top tether anchorage
A
B
WARNING
■ When installing a child restraint sys-
tem
Observe the following precautions.
Failure to do so may result in death or
serious injury.
● Firmly attach the top strap and make
sure that the belt is not twisted.
A
B
65
1
1-2. Child safety
For safety and security
WARNING
● Do not attach the top strap to anything
other than the top tether anchorage.
● After securing a child restraint system,
never adjust the seat.
● Follow all installation instructions pro-
vided by the child restraint system
manufacturer.
● When installing the child restraint sys-
tem with the head restraint being
raised, after the head restraint has
been raised and then the top tether
anchorage has been fixed, do not
lower the head restraint.

Related Topics

Popular Owner Manuals