2013-2016 Mazda Cx-5 SUV Tire Information (U.S.A.) -> Location of the Tire Label (Placard) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Tire Information (U.S.A.) -> Location of the Tire Label (Placard) for Your Mazda Cx-5 SUV First Generation (2013-2016)

Customer Information and Reporting Safety Defects  
Tire Information (U.S.A.)  
Location of the Tire Label (Placard)  
You will find the tire label containing tire inflation pressure by tire size and other important  
information on the driver's side B-pillar or on the edge of the driver's door frame.  
SAMPLE  
qRecommended Tire Inflation Pressure  
On the tire label you will find the recommended tire inflation pressure in both kPa and psi  
for the tires installed as original equipment on the vehicle. It is very important that the  
inflation pressure of the tires on your vehicle is maintained at the recommended pressure.  
You should check the tire pressure regularly to insure that the proper inflation pressure is  
maintained.  
Refer to Tires on page 9-8.  
NOTE  
Tire pressures listed on the vehicle placard or tire information label indicate the recommended cold  
tire inflation pressure, measured when the tires are cold, after the vehicle has been parked for at least  
3 hours. As you drive, the temperature in the tire warms up, increasing the tire pressure.  
8-31  
Customer Information and Reporting Safety Defects  
Tire Information (U.S.A.)  
WARNING  
Always check the tire inflation pressures on a regular basis according to the  
recommended tire inflation pressure on the tire label and in conjunction with the  
information in this owner's manual:  
Driving your vehicle with under-inflated tires is dangerous.  
Under-inflation is the most common cause of failures in any kind of tire and may  
result in severe cracking, tread separation or blowout, with unexpected loss of  
vehicle control and increased risk of injury. Under-inflation increases sidewall flexing  
and rolling resistance, resulting in heat buildup and internal damage to the tire. It  
results in unnecessary tire stress, irregular wear, loss of control and accidents. A tire  
can lose up to half of its air pressure and not appear to be flat!  
It is impossible to determine whether or not tires are properly inflated just by looking  
at them.  
qChecking Tire Pressure  
1. When you check the air pressure, make sure the tires are cold meaning they are not  
hot from driving even a mile.  
2. Remove the cap from the valve on one tire.  
3. Firmly press a tire gauge onto the valve.  
4. Add air to achieve recommended air pressure.  
5. If you overfill the tire, release air by pushing on the metal stem in the center of the  
valve. Then recheck the pressure with your tire gauge.  
6. Replace the valve cap.  
7. Repeat with each tire, including the spare.  
NOTE  
Some spare tires require higher inflation pressure.  
8. Visually inspect the tires to make sure there are no nails or other objects embedded that  
could poke a hole in the tire and cause an air leak.  
9. Check the sidewalls to make sure there are no gouges, cuts, bulges, cracks or other  
irregularities.  
8-32  
Customer Information and Reporting Safety Defects  
Tire Information (U.S.A.)  
qGlossary of Terms  
Tire Placard: A label indicating the OE tire sizes, recommended inflation pressure, and  
the maximum weight the vehicle can carry.  
Tire Identification Number (TIN): A number on the sidewall of each tire providing  
information about the tire brand and manufacturing plant, tire size, and date of  
manufacture.  
Inflation Pressure: A measure of the amount of air in a tire.  
kPa: Kilopascal, the metric unit for air pressure.  
psi: Pounds per square inch, the English unit for air pressure.  
B-pillar: The structural member at the side of the vehicle behind the front door.  
Original Equipment (OE): Describes components originally equipped on the vehicle.  
Vehicle Load Limit: The maximum value of the combination weight of occupants and  
cargo.  
Bead Area of the Tire: Area of the tire next to the rim.  
Sidewall Area of the Tire: Area between the bead area and the tread.  
Tread Area of the Tire: Area on the perimeter of the tire that contacts the road when it's  
mounted on the vehicle.  
Seating capacity means the total allowable number of vehicle occupants. Seating capacity  
is described on the tire label.  
Production options weight is the combination weight of installed regular production  
options weighing over 2.3 kilograms in excess of the standard items which they replace,  
and not previously considered in the curb weight or accessory weight, including heavy  
duty brakes, ride levelers, roof rack, heavy duty battery, and special trim.  
Rim is the metal support (wheel) for a tire or a tire and tube assembly upon which the tire  
beads are seated.  
8-33  

Related Topics

Popular Owner Manuals