1998-2004 Mazda Mx-5 SUV Interior Comfort -> Audio System User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Interior Comfort -> Audio System for Your Mazda Mx-5 SUV Second Generation (1998-2004)

Antenna
qPower Antenna
The antenna automatically rises when the
radio is turned on, and lowers when it is
turned off.
CAUTION
l
To prevent damaging the antenna,
retract it before entering a car wash
facility or passing beneath a low
overhead clearance.
l
Make sure no one is near the antenna
before turning on the radio to
prevent injury or damage to the
antenna.
Operating Tips for Audio
System
WARNING
Do Not Adjust Audio While Driving
the Vehicle:
Adjusting the audio while driving the
vehicle is dangerous as it could
distract your attention from the vehicle
operation which could lead to a
serious accide nt. Always adjust the
audio while the vehicle is stopped.
CAUTION
For the purposes of safe driving, adjust
the audio volume to a level that allows
you to hear sounds outside of the
vehicle.
NOTE
l
Do not use the audio for long periods
of time while the engine is off.
Otherwise the battery could go dead.
l
If a digital cellular phone or CB
radio is used in or near the vehicle, it
could cause noise to occur from the
audio system, however, this does not
indicate that the syst em has been
damaged.
Interior Comfort
Audio System
6-9
qRadio Reception
AM characteristics
AM signals bend around such things as
buildings or mountains and bounce off the
ionosphere. Therefore, they can reach
longer distances than FM signals. Because
of this, two stations may sometimes be
picked up on the same frequency at the
same time.
Station 2
Station 1
Ionosphere
FM characteristics
An FM broadcast range is usually about
40―50 km (25―30 miles) from the
source. Because of extra coding needed to
break the sound into two channels, stereo
FM has even less range than monaural
(non-stereo) FM.
(25—30 miles)
40—50 km
FM Station
Signals from an FM transmitter are similar
to beams of light because they do not
bend around corners, but they do reflect.
Unlike AM signals, FM signals cannot
travel beyond the horizon. Therefore, FM
stations cannot be received at the great
distances possible with AM reception.
AM wave
FM wave
FM wave
100—200 km (60—120 miles)
Ionosphere
Atmospheric conditions can also affect
FM reception. High humidity will cause
poor reception. However, cloudy days
may provide better reception than clear
days.
Multipath noise
Since FM signals can be reflected by
obstructions, it is possible to receive both
the direct signal and the reflected signal at
the same time. This causes a slight delay
in reception and may be heard as a broken
sound or a distortion. This problem may
also be encountered when in close
proximity to the transmitter.
Reflected wave
Direct
6-10
Interior Comfort
Audio System
Flutter/Skip noise
Signals from an FM transmitter move in
straight lines and become weak in valleys
between tall buildings, mountains, and
other obstacles. When a vehicle passes
through such an area, the reception
conditions may change suddenly, resulting
in annoying noise.
Weak signal noise
In suburban areas, broadcast signals
become weak because of distance from
the transmitter. Reception in such fringe
areas is characterized by sound breakup.
Strong signal noise
This occurs very close to a transmitter
tower. The broadcast signals are
extremely strong, so the result is noise and
sound breakup at the radio receiver.
Station drift noise
When a vehicle reaches the area of two
strong stat ions broadcasting at similar
frequencies, the original station may be
temporarily lost and the second station
picked up. At this time there will be some
noise from this disturbance.
Station 2
88.3 MHz
Station 1
88.1 MHz
Interior Comfort
Audio System
6-11
qOperating Tips for Cassette Tape
Player
Cleaning the cassette tape player
The tape head, capstans, and pinch rollers
will gather oxide residue from cassette
tapes. This can cause weak or wavering
sounds and damage to the cassette tapes
and player. Use a good quality head-
cleaning tape or a liquid cleaner cassette
tape to remove it.
Should the unit not operate normally,
consult an Authorized Mazda Dealer.
Never attempt to repair it or insert a
screwdriver or anything else.
Handling the cassette tape player
The following precautions should be
observed.
l
Do not spill any liquid on the audio
system.
l
Do not insert any objects, other than
cassette tape, into the slot.
l
If the cassette tape is loose, it may
produce poor sound or performance
during playback. Use a pencil or
something similar to remove any slack.
l
Only cassette tapes that play no longer
than 90 minutes should be used.
Cassette tape exceeding 90 minutes are
thin and may easily break.
l
Do not leave a cassette tape in the tape
player slot when not in use. Remove it
completely to permit the slot door to
close and to protect the mechanism
from dust.
l
Store cassette tapes away from extreme
heat, magnetic fields, and direct
sunlight. Protect the exposed cassette
tape from dirt and damage. Store
cassette tapes in thei r original cases or
other protective cases.
6-12
Interior Comfort
Audio System
qOperating Tips for Mini Disc
(MD) Player
The following precautions should be
observed.
l
Do not spill any liquid on the audio
system.
l
Do not insert any objects, other than
MDs, into the slot.
l
The MD player has been designed to
play MDs bearing the identification
logo as shown. No other MDs can be
played.
l
The MD player can also play MDLPs
that have been recorded in MDLP
mode. (MDLPs bearing the
identification logo as shown below).
l
When inser ting the MD, make sure the
MD label is facing up, and the MD is
oriented to the insertion slot in the
direction of the arrow. If not inserted
correctly, the MD will be ejected, or
may remain stuck in the MD deck.
l
Do not touch the internal part of the
MD. If the MD shutter is slid open for
no reason, it may be broken.
l
Store MDs in their cases and away
from direct sunlight.
Interior Comfort
Audio System
6-13
qOperating Tips for CD Player/In-
Dash CD Changer
Condensation phenomenon
Immediately after turning on the heater
when the vehicle is cold, the CD or
optical components (prism and lens) in the
CD player /changer may become clouded
with condens ation. At this time, the CD
will eject immediately when placed in the
unit. A clouded CD can be corrected
simply by wiping it with a soft cloth.
Clouded optical components will clear
naturally in about an hour. Wait for
normal operation to return before
attempting to use the unit.
Handling the CD player/In-dash CD
changer
The following precautions should be
observed.
l
Do not spill any liquid on the audio
system.
l
Do not insert any objects, other than
CDs, into the slot.
l
The CD revolves at high speed within
the unit. Defective (cracked or badly
bent) CDs should never be used.
l
Do not use non-conventional discs
such as heart-shaped, octagonal discs,
etc. The CD player/changer could be
damaged.
l
A new CD may have rough edges on
its inner and outer perimeters. If a disc
with rough edges is used, proper
setting will not be possible and the CD
player/changer will not play the CD.
Remove the rough edges in advance by
using a ball-point pen or pencil as
shown below. To remove the rough
edges, rub the side of the pen or pencil
against the inner and outer perimeter of
the CD.
6-14
Interior Comfort
Audio System
l
When driving over uneven surfaces,
the sound may jump.
l
The CD player/changer has been
designed to play CDs bearing the
identification logo as shown. No other
discs can be played.
l
Be sure never to touch the signal
surface when handling the CDs. Pick
up a CD by grasping the outer edge or
the edge of the hole and the outer edge.
l
Do not stick paper or tape on the CD.
Avoid scratching the reverse side (the
side without a label).
l
Dust, finge r smudges, and dirt can
decrease the amount of light reflected
from the signal surface, thus affecting
sound quality. If the CD should
become soiled, gently wipe it with a
soft cloth from the center of the CD to
the edge.
l
Do not use record sprays, antistatic
agents, or household spray cleaners.
Volatile chemicals such as benzine and
thinner can also damage the surface of
the CD and must not be used. Anything
that can damage, warp, or fog plastic
should never be used to clean CDs.
l
CDs, like traditional audio records, are
made of plastic. To avoid warping,
keep the CDs in their cases and do not
store them where they will be exposed
to direct sunlight.
l
The CD player/changer ejects the CD if
the CD is inserted upside down. Also
dirty and/or defective CDs may be
ejected.
l
8 cm (3 in) CDs and CD accessories
(e.g. 8 cm disc adapter) cannot be used
in the CD player/changer.
l
Do not insert cleaning discs in the CD
player/changer.
l
Do not insert any disc with a peel-off
or seal on it.
Interior Comfort
Audio System
6-15
6-16
Interior Comfort
Audio System
Types of the Audio Set
Audio Set (Type A) ....................................................................................... ......... page 6-19
Audio Set (Type B) ................................................................................................ page 6-43
(Some countries.)
Interior Comfort
Audio System
6-17
6-18
Interior Comfort
Audio System
Audio Set (Type A)
í
CD Player In-dash CD Changer
Cassette Tape Player Mini Disc (MD) Player
Illustration is of a representative audio unit.
Power/Volume/Sound Controls .............................................................................. page 6-20
Clock ...................................................................................................................... page 6-24
Operating the Radio ............................................................................................... page 6-26
Operating the Cassette Tape Player ........................................................................ page 6-28
Operating the Mini Disc (MD) Player .................................... ................................ page 6-32
Operating the Compact Disc (CD) Player .............................................................. page 6-36
Operating the In-Dash CD Changer ....................................................................... page 6-38
Error Indications ..................................................................................................... page 6-41
Interior Comfort
Audio System
6-19
í
Some models.
qPower/Volume/Sound Controls
Display
Audio control dialPower/Volume dial
Power ON/OFF
Turn the ignition switch to the ACC or
ON position.
Press the power/volume dial to turn the
audio system on.
Press the power/volume dial again to turn
the audio system off.
NOTE
To prevent the battery from being
discharged, do not leave the audio
system on for a long period of time
when the engine is not running.
Volume adjustment
To adjust the volume, turn the power/
volume dial.
Turn the power/volume dial to the right to
increase v olume, to the left to decrease it.
Audio sound adjustment
1. Press the audio control dial to select the
function. The selected function will be
indicated.
6-20
Interior Comfort
Audio System
2. Turn the audio control dial to adjust the
selected functions as follows:
BOSE Sound System-equipped model
*1
*1
*2
*1 Depending on the mode selected, the
indication changes.
*2 BAL function is available only for the
front speakers.
Indication Turn Left Turn Right
Select mode Select mode
Decrease bass Increase bass
Decrease
treble
Increase
treble
Shift the sound
to the front
Shift the sound
to the rear
(front speakers
only)
Shift the sound
to the left
Shift the sound
to the right
OFF ON
Standard audio-equipped model
*1
*2
*1 If your vehicle is not equipped with
rear speakers, adjust the power/
volume dial so the level is even.
*2 Depending on the mode selected, the
indication changes.
Indication Turn Left Turn Right
Decrease bass Increase bass
Decrease
mid-range
Increase
mid-range
Decrease
treble
Increase
treble
Shift the sound
to the front
Shift the sound
to the rear
Shift the sound
to the left
Shift the sound
to the right
OFF ON
NOTE
About 5 seconds after selecting any
mode, the volume function will be
automatically selected. To reset bass,
mid-range, treble, fade and balance,
press the audio control dial for 2
seconds. The unit will beep and
“CLEAR” will be displayed.
Interior Comfort
Audio System
6-21
Automatic Level Control (ALC)
(BOSE Sound System-equipped model)
The automatic level control is a feature
that automatically adjusts audio volume
and sound quality according to the vehicle
speed.
The volume increases in accordance with
the increase in vehicle speed, and
decreases as vehicle speed decreases.
The following 7 modes are available.
Select the desired mode according to use.
Mode Use
Volume
change
ALC does
not operate.
No change
Use when
the
convertible
top is
closed.
Three levels
are
available.
Minimum
Medium
Maximum
Use when
the
convertible
top is open.
Three levels
are
available.
Minimum
Medium
Maximum
Turn the audio control dial to select the
desired mode. The selected mode will be
indicated.
BEEP setting
The beep-sound when operating the audio
system can be set on or off.
6-22
Interior Comfort
Audio System
Interior Comfort
Audio System
6-23
qClock
Display Clock button
Hour set
button
Minute set
button
Setting the time
The clock can be set at any time when the
ignition switch is in the ACC or ON
position.
1. To adjust the time, press the clock
button (
) for about 2 seconds
until a beep is heard.
The clock's current time will flash.
NOTE
To select 12-hour or 24-hour clock
time, turn the audio control dial while
the clock display is flashing. After
selecting the desired display, press the
audio control dial to return to the
flashing clock display.
2. To advance the hours, press the hour
set button (
). To advance the
minutes, press the minute set button
(
) while the time is flashing.
3. Press the clock button (
) again
to start the clock.
Exact hour adjustment
1. To set the exact hour, press the clock
button (
) for about 2 seconds
until a beep is heard.
The clock's current time will flash.
2. Press the clock button (
) again
and the time will be adjusted as
follows:
(Example)
12:01―12:29→12:00
12:30―12:59→1:00
6-24
Interior Comfort
Audio System
NOTE
l
When the clock button (
) is
released, the seconds are reset to
“00”.
l
If the power supply to the unit is
interrupted (if the fuse blows or the
vehicle's battery is disconnected), the
clock will need to be reset.
Changing the display mode
The display on the unit can be changed by
pressing the clock button (
). This
alternates the display between clock mode
and normal mode. When the clock mode
has been selected, the time will be
displayed.
NOTE
The displays when using the audio
differ in clock mode and normal mode.
Interior Comfort
Audio System
6-25
qOperating the Radio
Band selector button
Satellite button*
Display
Channel preset buttons
Scan button
Manual tuning dial
*For reception of optional SIRIUS digital satellite radio.
Used on vehicles equipped with the separately sold SIRIUS digital satellite radio unit.
For information on use, read the manual accompanying the SIRIUS unit.
Subscription of SIRIUS digital satellite radio service is available in the U.S. (Except Alaska and Hawaii).
Seek tuning
button
Auto memory
button/Electric
serial number
button*
Radio ON
Press a band selector button (
) to
turn the radio on.
Band selection
Successively pressing the band selector
button (
) switches the bands as
follows: FM1→FM2→AM.
The selected mode wi ll be indicated. If
FM stereo is being received, “ST” will be
displayed.
NOTE
If the FM broadcast signal becomes
weak, reception automatically changes
from STER EO to MONO for reduced
noise, and the “ST” indicator will go
out.
Tuning
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
Manual tuning
Turning the manual tuning dial will
change the frequency higher or lower.
6-26
Interior Comfort
Audio System
Seek tuning
Pressing the seek tuning button (
, )
will cause the tuner to seek a higher or
lower frequency automatically.
NOTE
If you continue to press and hold the
button, the frequency will continue
changing without stopping.
Scan tuning
Press the scan button (
) to
automatically sample strong stations.
Scanning stops at each station for about 5
seconds. To hold a station, merely press
the scan button (
) again during this
interval.
Preset channel tuning
The 6 preset channels can be used to store
6 AM and 12 FM stations.
1. To set a channel first select AM, FM1,
or FM2. Tune to the station you want.
2. Depress a channel preset button for
about 2 seconds until a beep is heard.
The preset channel number and station
frequency will be displayed. The
station is now held in the memory.
NOTE
When the clock is displayed, the preset
channel number will not be displayed.
3. Repeat this operation for the other
stations and bands you want to store.
To tune one in the memory, select AM,
FM1, or FM2 and then press its
channel preset button. The station
frequency and the channel number will
be displayed.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
Auto memory tuning
This is especially useful when driving in
an area where the local stations are not
known. Additional AM/FM stations can
be stored without disturbing the
previously set channels.
Press and hold the auto memory button
(
) for about 2 seconds until a beep
is heard; the system will autom atically
scan and temporarily store up to 6 stations
with the strongest frequencies in each
selected band in that area.
After scanning is completed, the station
with the strongest frequency will be tuned
and its frequency displayed.
Press and release the auto memory button
(
) to recall stations from the auto-
stored stat ions. One stored station will be
selected each time; its frequency and
channel number will be displayed.
NOTE
l
When the clock is displayed, the
preset channel number will not be
displayed.
l
If no stations can be tuned after
scanning operations, “A” will be
displayed.
Interior Comfort
Audio System
6-27
qOperating the Cassette Tape Player
í
Display
Cassette tape play button
Cassette tape eject button
Fast-forward button
Program button
Dolby NR button
Repeat button
APC button:
(next program)
(one being
played)
Rewind
button
Cassette tape insert
Insert the cassette tape into the slot, open
edge to the right and cassette tape will
begin play and “TAPE” will be displayed.
At the end of the cassette tape, the unit
automatically reverses cassette tape play.
When
is lit, the cassette tape's top
side is playing. When
is lit, the
bottom side is on.
NOTE
When a metal tape is inserted, the
player will automatically compensate
for it.
Playing
Press the cassette tape play button
(
) to start playing when a
cassette tape is in the unit. If there isn't a
cassette tape in the unit when the cassette
tape play button (
) is pressed,
“No TAPE” will flash on and off in
sequence.
6-28
Interior Comfort
í
Some models.
Audio System
Dolby noise reduction
When using a tape with Dolby NR*, push
the Dolby NR button (
). The
symbol wi ll be displayed. To play a tape
without Dolby NR, push the button once
again.
* Noise reduction system manufactured
under license from Dolby Laboratories
Licensing Corporation.
Dolby and the double-D symbol
are trade marks of Dolby Laboratories
Licensing Corporation.
Ejecting the cassette tape
Press the cassette tape eject button (
) to
eject the cassette tape.
NOTE
The cassette tape can be ejected when
the ignition switch is in the OFF
position.
Fast-forward/Rewind
Press the fast-forward button (
) to
fast-forward.
Press the rewind button (
) to rewind.
To stop this operation and play the
cassette tape, press the button again.
NOTE
When the cassette tape ends during fast-
forward or rewind, it automatically
stops and starts playing.
Reversing
Press the program button (
) to
change cassette tape-playing direction.
NOTE
When the cassette tape ends, the unit
automatically reverses play.
Automatic program control (APC)
APC is used to find the beginning of
either the next program or the one being
played.
Press the APC button (
) to the
beginning of the next selection.
Press the APC button (
) to the
beginning of the one being played. To
stop this operation and play the cassette
tape, press the button again.
If APC detects 4 seconds of blank space it
will automatically advance the tape to the
next selection.
NOTE
APC may not operate properly if
l
A tape was recorded at a low level.
l
A tape has long, silent intervals.
l
A tape is a live recording.
l
A tape has very short intervals of
less than 3 seconds.
Repeat play
This operation makes it possible to listen
to a selection repeatedly.
Press the repeat button (
) during play.
The current selection playing will be
repeated ( “ RPT” will be displayed).
Press the repeat button (
) once again
to cancel repeat play.
Interior Comfort
Audio System
6-29
NOTE
RPT may not operate properly if
l
A tape was recorded at a low level.
l
A tape has long, silent intervals.
l
A tape is a live recording.
l
A tape has very short intervals of
less than 3 seconds.
6-30
Interior Comfort
Audio System
Interior Comfort
Audio System
6-31
qOperating the Mini Disc (MD) Player
í
Main display Fast-forward button
MD play button
Reverse button
Repeat button
MD display
MD slot
Random button
MD display button
Track up
button
Track down
button
Scan button
Display
button
MD eject
button
Display
feed dial
Inserting the MD
Insert the MD, label-side up with the
arrow point ed to the slot. The auto-
loading mechanism will set the MD and
begin play. There will be a short lapse
before play begins while the player reads
the digital signals on the MD.
The track number and the elapsed play
back time for the current track will be
displayed on the display.
NOTE
When the clock is displayed, the
elapsed play back time will not be
displayed. To display the elapsed play
back time, turn the audio control dial to
the right. Turn the dial to the left to
return to the previous display.
Playing
Press the MD play button (
) to
start playing when a MD is in the unit.
Ejecting the MD
Press the MD eject button (
) to eject the
MD.
Fast-forward/Reverse
Press and hold the fast-forward button
(
) to advance through a track at high
speed.
Press and hold the reverse button (
)
to reverse through a track at high speed.
6-32
Interior Comfort
í
Some models.
Audio System
Track search
Press the track up button (
) once to
skip forward to the beginning of the next
track.
Press the track down button (
) once to
skip back to the beginning of the current
track.
Music scan
This featu re helps to find a program by
playing about the first 10 seconds of each
track.
Press the scan button (
) during play
to start scan play operation (the track
number will flash).
Press the scan button (
) once again
to cancel scan play.
NOTE
If the unit is left in scan, normal play
will resume where scan was selected.
Repeat play
This featu re makes it possible to listen to
a selection repeatedly.
Press the repeat button (
) during play.
The current selection will be repeated
(“RPT” will be displ ayed).
Press the repeat button (
) once again
to cancel repeat play.
Random play
This featu re allows the MD player to
randomly select the order of the songs.
Press the random button (
) during
play. The next selection will be randomly
selected (“RDM” will be displayed).
Press the random button (
) once
again to cancel random play.
Changing the display
Display
To change the display during MD play,
press the display button (
) to advance
through each of the following displays:
Track number/Elapsed play back
time→Song title→Disc title.
NOTE
l
If there is no song or d isc title
recorded on the MD, “No TITLE”
will be displayed.
l
The display can only display English
(including numerals) one-byte
characters. If any other character is
included “No TITLE” will be
displayed.
When long disc or song titles cannot be
completely displayed, rotate the display
feed dial (
) to the right.
The remainder of the title will proceed
and appear on the display to the end of the
title.
MD display
To change the MD display during MD
play, press and hold the MD display
button (
) for about half a second to
advance through each of the following
displays:
Song title→Disc title→No display.
NOTE
If there is no song or d isc title recorded
on the MD, “No TITLE” will be
displayed.
Interior Comfort
Audio System
6-33
When long disc or song titles cannot be
completely displayed, press the MD
display butt on (
) to display the
remaining part of the title.
6-34
Interior Comfort
Audio System
Interior Comfort
Audio System
6-35
qOperating the Compact Disc (CD) Player
í
Display
CD slot
Disc-in indicator
CD play button
Random button
Repeat button
Fast-forward button
CD eject
button
Scan button
Reverse
button
Track up
button
Track down
button
Inserting the CD
Insert the CD into the slot, label-side up.
The auto-loading mechanism will set the
CD and begin play. There will be a short
lapse before play begins while the player
reads the digital signa ls on the CD.
The disc-in indicator will illuminate, and
the track number and the elapsed play
back time for the current track will be
displayed.
NOTE
When the clock is displayed, the
elapsed play back time will not be
displayed. To display the elapsed play
back time, turn the audio control dial to
the right. Turn the dial to the left to
return to the previous display.
Playing
Press the CD play button (
) to start
playing when a CD is in the unit.
Ejecting the CD
Press the CD eject button (
) to eject the
CD.
Fast-forward/Reverse
Press and hold the fast-forward button
(
) to advance through a track at high
speed.
Press and hold the reverse button (
)
to reverse through a track at high speed.
6-36
Interior Comfort
í
Some models.
Audio System
Track search
Press the track up button (
) once to
skip forward to the beginning of the next
track.
Press the track down button (
) once to
skip back to the beginning of the current
track.
Music scan
This featu re helps to find a program by
playing about the first 10 seconds of each
track.
Press the scan button (
) during play
to start scan play operation (the track
number will flash).
Press the scan button (
) once again
to cancel scan play.
NOTE
If the unit is left in scan, normal play
will resume where scan was selected.
Repeat play
This featu re makes it possible to listen to
a selection repeatedly.
Press the repeat button (
) during play.
The current selection will be repeated
(“RPT” will be displ ayed).
Press the repeat button (
) once again
to cancel repeat play.
Random play
This featu re allows the CD player to
randomly select the order of the songs.
Press the random button (
) during
play. The next selection will be randomly
selected (“RDM” will be displayed).
Press the random button (
) once
again to cancel random play.
Interior Comfort
Audio System
6-37
qOperating the In-Dash CD Changer
í
Display
CD slot
Disc-in indicator CD play button
Random button
Repeat button
Disc up button
Reverse button
Load button
Power/Volume dial
Channel preset buttons
CD eject
button
Scan button
Fast-forward
button
Track up
button
Track down
button
Disc down
button
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number, the track number and
the elapsed play back time for the current
track will be displayed.
NOTE
l
When the clock is displayed, the
elapsed play back time will not be
displayed. To display the elapsed
play back time, turn the audio
control dial to the right. Turn the dial
to the left to return to the previous
display.
l
A CD cannot be inserted while the
display reads “WAIT”. A beeping
sound can be heard during this
waiting time. Simultaneousl y
pressing the power/volume dial and
the load button (
) for about 2
seconds will turn this beeping sound
ON or OFF.
6-38
Interior Comfort
í
Some models.
Audio System
Normal insertion
1. Press the load button (
).
2. When “In” is displayed, insert the CD.
Inserting CDs into desired tray number
1. Press and hold the load button (
)
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the
desired tray number within 3 seconds
after the beep is heard.
3. When “In” is displayed, insert the CD.
NOTE
The CD cannot be inserted to the
desired tray number if the number is
already occupied.
Multiple insertion
1. Press and hold the load button (
)
for about 2 seconds until a beep is
heard.
2. When “In” is displayed, insert the CD.
3. When “In” is displayed again, insert
the next CD.
NOTE
The first-inserted CD will be played
automatically when:
l
No other CD is inserted within 15
seconds after “In” is displayed.
l
The CD trays are full.
Ejecting the CD
Normal ejection
1. Press the CD eject button (
). The
disc number and “DISC OUT” will be
displayed.
2. Pull out the CD.
NOTE
When the CD is ejected during play, the
next CD will be played automati cally.
Ejecting CDs from desired tray number
1. Press and hold the CD eject button (
)
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the
desired CD number within 3 seconds
after the beep is heard.
3. Pull out the CD.
Multiple ejection
1. Press and hold the CD eject button (
)
for about 2 seconds until a beep is
heard.
2. Wait 3 seconds or press the CD eject
button (
) again within 3 seconds
after the beep is heard.
3. Pull out the CD, then the next CD will
be ejected .
Interior Comfort
Audio System
6-39
NOTE
l
CDs will be ejected starting with the
one with the lowest number.
l
All CDs in the tray will be ejected
continuously.
l
CDs can be ejected when the ignition
switch is off. Press and hold the CD
eject button (
) for about 2 seconds
and all CDs will eject.
Playing
Press the CD play button (
) to start
playing when a CD is in the unit.
Fast-forward/Reverse
Press and hold the fast-forward button
(
) to advance through a track at high
speed.
Press and hold the reverse button (
)
to reverse through a track at high speed.
Track search
Press the track up button (
) once to
skip forward to the beginning of the next
track.
Press the track down button (
) once to
skip back to the beginning of the current
track.
Disc search
Press the disc up button (
) to skip
forward to the beginning of the next CD.
Press the disc down button (
) to
skip back to the beginning of the previous
CD.
Music scan
This featu re helps to find a program by
playing about the first 10 seconds of each
track.
Press the scan button (
) during play
to start scan play operation (the track
number will flash).
Press the scan button (
) once again
to cancel scan play.
NOTE
If the unit is left in scan, normal play
will resume where scan was selected.
Repeat play
This featu re makes it possible to listen to
a selection repeatedly.
Press the repeat button (
) during play.
The current selection will be repeated
(“RPT” will be displ ayed).
Press the repeat button (
) once again
to cancel repeat play.
Random play
This featu re allows the CD player to
randomly select the order of the songs.
Press the random button (
) during
play. The next selection will be randomly
selected (“RDM” will be displayed).
Press the random button (
) once
again to cancel random play.
6-40
Interior Comfort
Audio System
qError Indications
If you see an error indication on the display, find the cause in the chart. If you cannot clear
the error indication, take the vehicle to an Authorized Mazda Dealer.
Indication Cause Solution
CHECK MD
MD is inserted upside down
Insert the MD properly. If the error indication does not
disappear, consult an Authorized Mazda Dealer.
MD is defective
Insert another MD properly. If the error indication does not
disappear, consult an Authorized Mazda Dealer.
CHECK CD
CD is inserted upside down
Insert the CD properly. If the error indication does not disappear,
consult an Authorized Mazda Dealer.
CD is defective
Insert another CD properly. If the error indication does not
disappear, consult an Authorized Mazda Dealer.
Interior Comfort
Audio System
6-41
6-42
Interior Comfort
Audio System
Audio Set (Type B)
í
CD Player In-dash CD Changer
Cassette Tape Player Mini Disc (MD) Player
Illustration is of a representative audio unit.
(Some countries.)
Antitheft System .................................................................................................... page 6-44
Power/Volume/Sound Controls .............................................................................. page 6-48
Clock ...................................................................................................................... page 6-50
Operating the Radio ............................................................................................... page 6-52
Operating the Cassette Tape Player ........................................................................ page 6-54
Operating the Mini Disc (MD) Player .................................... ................................ page 6-58
Operating the Compact Disc (CD) Player .............................................................. page 6-60
Operating the In-Dash CD Changer ....................................................................... page 6-62
Error Indications ..................................................................................................... page 6-65
Interior Comfort
Audio System
6-43
í
Some models.
qAntitheft System
í
Display
Channel preset buttons
Antitheft indicator light
Auto memory
button
To deter theft of your vehicle's audio unit,
it has an integrated antitheft system. The
system is designed to accept a code
number that makes the unit inoperable if it
is stolen.
This system will be activated if the power
source is ever disconnected from or in any
way interrupted to the audio unit. When
the system is activated, the audio system
will not operate when reconnected to a
power supply, and “CODE” will flash on
the display until the correct code number
is input. If the antitheft system is
activated, reset the unit.
CAUTION
Read and understand all code setting
procedures before attempting to input
your personal code number.
The personal code number is only
shown on the audio unit display while it
is being set. Once it is input and stored
by the unit, it is never again displayed.
For that reason, be very careful to
immediately record your personal code
number, and never let an unauthorized
person set a code.
NOTE
Although the audio unit is operable
without the code number being set, we
recommend that you set your person al
code number.
6-44
Interior Comfort
í
Some models.
Audio System
Setting procedure
1. Begin with the audio unit off and the
ignition switch is in the ACC position.
2. Press the auto memory button
(
) and the channel preset button
6 simultaneously for about 2 seconds
until “CODE” is displayed.
3. Again press the auto memory button
(
) and the channel preset button
6 simultaneously while “ CODE” is
displayed (within 10 seconds). The
display wi ll exhibit bars.
4. While the bars are displayed, input
your personal code number by press ing
channel preset buttons 1, 2, 3, and 4.
Press 1 for the first digit, 2 for the second,
3 for the third, and 4 for the last digit. For
example, if your number is 2547, press 1
three times, 2 six times, 3 five times, and
4 eight times. If the display goes off while
inputting, begin from Step 1.
NOTE
We recommend that your code number
be associated with something easy to
remember. You should also file a copy
of the code numbers with your
important papers.
5. While the code number is displayed,
press the auto memory button
(
) and the channel preset button
6 simultaneously for about 2 seconds
and “CODE” begins to flash. After
about 5 seconds, “CODE” will
disappear. This indicates the system is
set.
Canceling code number
1. Begin with the audio unit off and the
ignition switch is in the ACC position.
Interior Comfort
Audio System
6-45
2. Press the auto memory button
(
) and the channel preset button
6 simultaneously for about 2 seconds
until “CODE” is displayed.
3. Again press the auto memory button
(
) and the channel preset button
6 simultaneously while “ CODE” is
displayed (within 10 seconds). The
display wi ll exhibit bars.
4. While the bars are displayed, input the
current co de number as described in
setting procedure Step 4. (2547, for
example).
5. While the code number is displayed,
press the auto memory button
(
) and the channel preset button
6 simultaneously for about 2 seconds
and “CODE” appears.
6. After 5 seconds, “CODE” will
disappear. This indicates the code
number is canceled.
NOTE
If Err (error) appears on the display,
begin from Step 4.
Changing code number
To change the code numbe r, first cancel
the number. Then set the new number by
following the setting procedures.
System activation
When the power supply is disconnected or
interrupted, the antitheft system is
activated and the unit is render ed
inoperative. In this condition, when power
is again supplied, “CODE” will be
displayed and flash unless the correct
code number is input.
6-46
Interior Comfort
Audio System
To deactivate the antitheft system and
reset the audio unit, input your personal
code number.
1. Press the auto memory button
(
) and the channel preset button
6 simultaneously until bars are
displayed.
2. While the bars are displayed, input the
code number as described in the setting
procedure.
3. Press the auto memory button
(
) and the channel preset button
6 for about 2 seconds. “CODE” will be
flashed for 5 seconds, then disappear to
indicate that the syst em is operable. If
Err (error) appears, begin from Step 1.
CAUTION
l
Three consecutive errors will
activate the antitheft system, and the
audio unit will be completely
inoperable and Err (error) will flash.
When this happens, the unit must be
replaced by an Authorized Mazda
Dealer at the owner's expense.
l
Do not allow an unauthorized person
to attempt to input a code number.
Interior Comfort
Audio System
6-47
qPower/Volume/Sound Controls
Display
Audio control dial Power/Volume dial
Power ON/OFF
Turn the ignition switch to the ACC or
ON position.
Press the power/volume dial to turn the
audio system on.
Press the power/volume dial again to turn
the audio system off.
NOTE
To prevent the battery from being
discharged, do not leave the audio
system on for a long period of time
when the engine is not running.
Volume adjustment
To adjust the volume, turn the power/
volume dial.
Turn the power/volume dial to the right to
increase v olume, to the left to decrease it.
Audio sound adjustment
1. Press the audio control dial to select the
function. The selected function will be
indicated.
6-48
Interior Comfort
Audio System
*
If your vehicle is not equipped with rear
speakers, adjust the power/volume dial so
level is even.
2. Turn the audio control dial to adjust the
selected functions as follows:
Indication Turn Left Turn Right
Decrease bass Increase bass
Decrease
mid-range
Increase
mid-range
Decrease
treble
Increase
treble
Shift the sound
to the front
Shift the sound
to the rear
Shift the sound
to the left
Shift the sound
to the right
NOTE
About 5 seconds after selecting any
mode, the volume function will be
automatically selected. To reset bass,
mid-range, treble, fade, and balance,
press the audio control dial for 2
seconds. The unit will beep and “CL”
will be displayed.
Interior Comfort
Audio System
6-49
qClock
Display Clock button
Hour set
button
Minute set
button
Setting the time
The clock can be set at any time when the
ignition switch is in the ACC or ON
position.
1. To adjust the time, press the clock
button (
) for about 2 seconds
until a beep is heard.
The clock's current time will flash.
2. To advance the hours, press the hour
set button (
). To advance the
minutes, press the minute set button
(
) while the time is flashing.
3. Press the clock button (
) again
to start the clock.
Exact hour adjustment
1. To set the exact hour, press the clock
button (
) for about 2 seconds
until a beep is heard.
The clock's current time will flash.
2. Press the clock button (
) again
and the time will be adjusted as
follows:
(Example)
12:01―12:29→12:00
12:30―12:59→1:00
NOTE
If the power supply to the unit is
interrupted (if the fuse blows or the
vehicle's battery is disconnected), the
clock will need to be reset.
6-50
Interior Comfort
Audio System
Changing the display mode
The display on the unit can be changed by
pressing the clock button (
). This
alternates the display between time and
audio. When the clock mode has been
selected, the time will be displayed.
NOTE
If audio operation is selected while the
time mode is on, the selected audio
mode will be displayed for 10 seconds,
then the display will revert to the time
mode.
Interior Comfort
Audio System
6-51
qOperating the Radio
Band selector buttons Display
Channel preset buttons
Scan button
Manual tunin
g
dial
Seek tuning
button
Auto memory
button
Radio ON
Press a band selector button (
or
) to turn the radio on.
Band selection
Choose AM by pressing the AM button
(
) and FM by pressing the FM1/2
button (
).
The selected mode wi ll be indicated. If
FM stereo is being received, “ST” will be
displayed.
NOTE
If the FM broadcast signal becomes
weak, reception automatically changes
from STER EO to MONO for reduced
noise, and the “ST” indicator will go
out.
Tuning
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
Manual tuning
Turning the manual tuning dial will
change the frequency higher or lower.
6-52
Interior Comfort
Audio System
Seek tuning
Pressing the seek tuning button (
, )
will cause the tuner to seek a higher or
lower frequency automatically.
NOTE
If you continue to press and hold the
button, the frequency will continue
changing without stopping.
Scan tuning
Press the scan button (
) to
automatically sample strong stations.
Scanning stops at each station for about 5
seconds. To hold a station, merely press
the scan button (
) again during this
interval.
Preset channel tuning
The 6 preset channels can be used to store
6 AM and 12 FM stations.
1. To set a channel first select AM, FM1,
or FM2. Tune to the station you want.
2. Depress a channel preset button for
about 2 seconds until a beep is heard.
The preset channel number and station
frequency will be displayed. The
station is now held in the memory.
3. Repeat this operation for the other
stations and bands you want to store.
To tune one in the memory, select AM,
FM1, or FM2 and then press its
channel preset button. The station
frequency and the channel number will
be displayed.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
Auto memory tuning
This is especially useful when driving in
an area where the local stations are not
known. Additional AM/FM stations can
be stored without disturbing the
previously set channels.
Press and hold the auto memory button
(
) for about 2 seconds until a beep
is heard; the system will autom atically
scan and temporarily store up to 6 stations
with the strongest frequencies in each
selected band in that area.
After scanning is completed, the station
with the strongest frequency will be tuned
and its frequency displayed.
Press and release the auto memory button
(
) to recall stations from the auto-
stored stat ions. One stored station will be
selected each time; its frequency and
channel number will be displayed.
NOTE
If no stations can be tuned after
scanning operations, “A” will be
displayed.
Interior Comfort
Audio System
6-53
qOperating the Cassette Tape Player
í
Display
Cassette tape play button
Cassette tape eject button
Fast-forward button
Program button
Dolby NR button
Repeat button
APC button:
(next program)
(one being
played)
Rewind button
Cassette tape insert
Insert the cassette tape into the slot, open
edge to the right and cassette tape will
begin play and “TAPE” will be displayed.
At the end of the cassette tape, the unit
automatically reverses cassette tape play.
When
is lit, the cassette tape's top side
is playing. When
is lit, the bottom side
is on.
NOTE
When a metal tape is inserted, the
player will automatically compensate
for it and “MTL” will be displayed.
Playing
Press the cassette tape play button
(
) to start playing when a
cassette tape is in the unit. If there isn't a
cassette tape in the unit when the cassette
tape play button (
) is pressed,
“NO TAPE” will flash on and off in
sequence.
Dolby noise reduction
When using a tape with Dolby NR*, push
the Dolby NR button (
). The
symbol wi ll be displayed. To play a tape
without Dolby NR, push the button once
again.
6-54
Interior Comfort
í
Some models.
Audio System
* Noise reduction system manufactured
under license from Dolby Laboratories
Licensing Corporation.
Dolby and the double-D symbol
are
trademarks of Dolby Laboratories
Licensing Corporation.
Ejecting the cassette tape
Press the cassette tape eject button (
) to
eject the cassette tape.
NOTE
The cassette tape can be ejected when
the ignition switch is in the OFF
position.
Fast-forward/Rewind
Press the fast-forward button (
) to
fast-forward.
Press the rewind button (
) to rewind.
To stop this operation and play the
cassette tape, press the button again.
NOTE
When the cassette tape ends during fast-
forward or rewind, it automatically
stops and starts playing.
Reversing
Press the program button (
) to
change cassette tape-playing direction.
NOTE
When the cassette tape ends, the unit
automatically reverses play.
Automatic program control (APC)
APC is used to find the beginning of
either the next program or the one being
played.
Press the APC button (
) to the
beginning of the next selection.
Press the APC button (
) to the
beginning of the one being played. To
stop this operation and play the cassette
tape, press the button again.
If APC detects 4 seconds of blank space it
will automatically advance the tape to the
next selection.
NOTE
APC may not operate properly if
l
A tape was recorded at a low level.
l
A tape has long, silent intervals.
l
A tape is a live recording.
l
A tape has very short intervals of
less than 3 seconds.
Repeat play
This operation makes it possible to listen
to a selection repeatedly.
Press the repeat button (
) during play.
The current selection playing will be
repeated ( “ RPT” will be displayed).
Press the repeat button (
) once again
to cancel repeat play.
Interior Comfort
Audio System
6-55
NOTE
RPT may not operate properly if
l
A tape was recorded at a low level.
l
A tape has long, silent intervals.
l
A tape is a live recording.
l
A tape has very short intervals of
less than 3 seconds.
6-56
Interior Comfort
Audio System
Interior Comfort
Audio System
6-57
qOperating the Mini Disc (MD) Player
í
Display
MD play button
Reverse button
Repeat button
MD display
MD slot
Random button
Fast-forward button
MD eject
button
Display
button
Track up
button
Track down
button
Scan
button
Inserting the MD
Insert the MD, label-side up with the
arrow point ed to the slot. The auto-
loading mechanism will set the MD and
begin play. There will be a short lapse
before play begins while the player reads
the digital signals on the MD.
Playing
Press the MD play button (
) to
start playing when a MD is in the unit.
Ejecting the MD
Press the MD eject button (
) to eject the
MD.
Fast-forward/Reverse
Press and hold the fast-forward button
(
) to advance through a track at high
speed.
Press and hold the reverse button (
)
to reverse through a track at high speed.
Track search
Press the track up button (
) once to
skip forward to the beginning of the next
track.
Press the track down button (
) once to
skip back to the beginning of the current
track.
Music scan
This featu re helps to find a program by
playing about the first 10 seconds of each
track.
6-58
Interior Comfort
í
Some models.
Audio System
Press the scan button ( ) during play
to start scan play operation (the track
number will flash).
Press the scan button (
) once again
to cancel scan play.
NOTE
If the unit is left in scan, normal play
will resume where scan was selected.
Repeat play
This featu re makes it possible to listen to
a selection repeatedly.
Press the repeat button (
) during play.
The current selection will be repeated
(“RPT” will be displ ayed).
Press the repeat button (
) once again
to cancel repeat play.
Random play
This featu re allows the MD player to
randomly select the order of the songs.
Press the random button (
) during
play. The next selection will be randomly
selected (“RDM” will be displayed).
Press the random button (
) once
again to cancel random play.
Changing the MD display
To change the MD display during MD
play, press and hold the display button
(
) for about half a second to advance
through each of the following displays:
Song title→Disc title→No display.
NOTE
If there is no song or d isc title recorded
on the MD, “NO TITLE” will be
displayed.
When disc or song titles cannot be
completely displayed, press the display
button (
) to display the remaining
part of the title.
Interior Comfort
Audio System
6-59
qOperating the Compact Disc (CD) Player
í
Display
CD slot
Disc-in indicator
CD play button
Random button
Repeat button
Fast-forward button
CD eject
button
Scan button
Reverse
button
Track up
button
Track down
button
Inserting the CD
Insert the CD into the slot, label-side up.
The auto-loading mechanism will set the
CD and begin play. There will be a short
lapse before play begins while the player
reads the digital signa ls on the CD.
The disc-in indicator will illuminate and
the track number will be displayed.
Playing
Press the CD play button (
) to start
playing when a CD is in the unit.
Ejecting the CD
Press the CD eject button (
) to eject the
CD.
Fast-forward/Reverse
Press and hold the fast-forward button
(
) to advance through a track at high
speed.
Press and hold the reverse button (
)
to reverse through a track at high speed.
Track search
Press the track up button (
) once to
skip forward to the beginning of the next
track.
Press the track down button (
) once to
skip back to the beginning of the current
track.
Music scan
This featu re helps to find a program by
playing about the first 10 seconds of each
track.
6-60
Interior Comfort
í
Some models.
Audio System
Press the scan button ( ) during play
to start scan play operation (the track
number will flash).
Press the scan button (
) once again
to cancel scan play.
NOTE
If the unit is left in scan, normal play
will resume where scan was selected.
Repeat play
This featu re makes it possible to listen to
a selection repeatedly.
Press the repeat button (
) during play.
The current selection will be repeated
(“RPT” will be displ ayed).
Press the repeat button (
) once again
to cancel repeat play.
Random play
This featu re allows the CD player to
randomly select the order of the songs.
Press the random button (
) during
play. The next selection will be randomly
selected (“RDM” will be displayed).
Press the random button (
) once
again to cancel random play.
Interior Comfort
Audio System
6-61
qOperating the In-Dash CD Changer
í
Disc-in indicator
Load button
Random button
Repeat button
Disc up button
Reverse button
Channel preset buttons
Display
CD slot
CD play button
CD eject
button
Scan button
Fast-forward
button
Track up
button
Track down
button
Disc down
button
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number and the track number
will be displayed.
NOTE
A CD cannot be inserted while the
display reads “WAIT”. A beeping
sound can be heard during this waiting
time. Simu ltaneously pressing the
power/volume dial and the load button
(
) for about 2 seconds will turn
this beeping sound ON or OFF.
Normal insertion
1. Press the load button (
).
2. When “In” is displayed, insert the CD.
Inserting CDs into desired tray number
1. Press and hold the load button (
)
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the
desired tray number within 3 seconds
after the beep is heard.
3. When “In” is displayed, insert the CD.
NOTE
The CD cannot be inserted to the
desired tray number if the number is
already occupied.
6-62
Interior Comfort
í
Some models.
Audio System
Multiple insertion
1. Press and hold the load button (
)
for about 2 seconds until a beep is
heard.
2. When “In” is displayed, insert the CD.
3. When “In” is displayed again, insert
the next CD.
NOTE
The first-inserted CD will be played
automatically when:
l
No other CD is inserted within 15
seconds after “In” is displayed.
l
The CD trays are full.
Ejecting the CD
Normal ejection
1. Press the CD eject button (
). The
disc number and “OUT ” will be
displayed.
2. Pull out the CD.
NOTE
When the CD is ejected during play, the
next CD will be played automati cally.
Ejecting CDs from desired tray number
1. Press and hold the CD eject button (
)
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the
desired CD number within 3 seconds
after the beep is heard.
3. Pull out the CD.
Multiple ejection
1. Press and hold the CD eject button (
)
for about 2 seconds until a beep is
heard.
2. Wait 3 seconds or press the CD eject
button (
) again within 3 seconds
after the beep is heard.
3. Pull out the CD, then the next CD will
be ejected .
NOTE
l
CDs will be ejected starting with the
one with the lowest number.
l
All CDs in the tray will be ejected
continuously.
l
CDs can be ejected when the ignition
switch is off. Press and hold the CD
eject button (
) for about 2 seconds
and all CDs will eject.
Playing
Press the CD play button (
) to start
playing when a CD is in the unit.
Fast-forward/Reverse
Press and hold the fast-forward button
(
) to advance through a track at high
speed.
Press and hold the reverse button (
)
to reverse through a track at high speed.
Track search
Press the track up button (
) once to
skip forward to the beginning of the next
track.
Press the track down button (
) once to
skip back to the beginning of the current
track.
Interior Comfort
Audio System
6-63
Disc search
Press the disc up button (
) to skip
forward to the beginning of the next CD.
Press the disc down button (
) to
skip back to the beginning of the previous
CD.
Music scan
This featu re helps to find a program by
playing about the first 10 seconds of each
track.
Press the scan button (
) during play
to start scan play operation (the track
number will flash).
Press the scan button (
) once again
to cancel scan play.
NOTE
If the unit is left in scan, normal play
will resume where scan was selected.
Repeat play
This featu re makes it possible to listen to
a selection repeatedly.
Press the repeat button (
) during play.
The current selection will be repeated
(“RPT” will be displ ayed).
Press the repeat button (
) once again
to cancel repeat play.
Random play
This featu re allows the CD player to
randomly select the order of the songs.
Press the random button (
) during
play. The next selection will be randomly
selected (“RDM” will be displayed).
Press the random button (
) once
again to cancel random play.
6-64
Interior Comfort
Audio System
qError Indications
If you see an error indication on the display, find the cause in the chart. If you cannot clear
the error indication, take the vehicle to an Authorized Mazda Dealer.
Indication Cause Solution
CHECK MD
MD is inserted upside down
Insert the MD properly. If the error indication does not
disappear, consult an Authorized Mazda Dealer.
MD is defective
Insert another MD properly. If the error indication does not
disappear, consult an Authorized Mazda Dealer.
CHECK CD
CD is inserted upside down
Insert the CD properly. If the error indication does not disappear,
consult an Authorized Mazda Dealer.
CD is defective
Insert another CD properly. If the error indication does not
disappear, consult an Authorized Mazda Dealer.
Interior Comfort
Audio System
6-65
Safety Certification
This CD player is made and tested to meet exacting safety standards. It meets FCC
requirements and complies with safety performance standards of the U.S. Department of
Health and Human Se rvices.
CAUTION
l
This CD player should not be adjusted or repaired by anyone except qualified service
personnel.
If servi cing is required, contact an Authorized Mazda Dealer.
l
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous laser exposure. Never operate the CD player
with the top case of the unit removed.
l
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
NOTE
For CD player section:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
6-66
Interior Comfort
Audio System

Related Topics

Interior Comfort
Climate Control System Interior Equipment
In Case of an Emergency

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot