Get On-board computer and displays -> Menus and submenus Guide for Mercedes CLA 4 Door First Generation (2013-2018)

The following messages may appear in the

multifunction display:

Z Gearshift recommendation for manual

transmission (Y page 143) or for automatic

transmission (shifting manually)

(Y page 150)

j Parking Pilot (Y page 180)

¯ Cruise control (Y page 162)

È Limiter (Y page 165)

_ Adaptive Highbeam Assist

(Y page 109)

è ECO start/stop function (Y page 137)

ë HOLD function (Y page 172)

120 km/h!120 km/h! Maximum permissible speed

exceeded (only for certain countries)

Menus and submenus

Menu overview

Using the = or ; button on the steering

wheel, open the menu bar.

Operating the on-board computer (Y page 201).

Depending on the equipment fitted in the vehi-

cle, you can call up the following menus:

TripTrip menu (Y page 203)

NaviNavi menu (navigation instructions)

(Y page 205)

AudioAudio menu (Y page 206)

TelTel menu (telephone) (Y page 207)

Assist.Assist. menu (assistance) (Y page 208)

Serv.Serv. menu (Y page 210)

SettingsSettings menu (settings) (Y page 210)

AMGAMG menu (Mercedes-AMG vehicles)

(Y page 213)

The displays for the AudioAudio, NaviNavi and TelTel menus

may differ slightly to those in your vehicle.

The examples given in this Owner's Manual

apply to vehicles equipped with COMAND

Online.

Trip menu

Standard display

Press and hold the % button on the steer-

ing wheel until the

TripTrip menu with trip

meter : and total distance recorder ;

appears.

Trip computer "From start" or "From

reset"

Distance

;

Driving time

Average speed

Average fuel consumption

Press the = or ; button on the steering

wheel to select the

TripTrip menu.

Press the 9 or : button to select

From startFrom start or From resetFrom reset.

The values in the FromFrom startstart submenu are cal-

culated from the start of a journey whilst the

values in the

From resetFrom reset submenu are calcu-

lated from the last time the submenu was reset

(Y page 204).

In the following cases, the trip computer is auto-

matically reset

From startFrom start:

the ignition has been switched off for more

than four hours

999 hours have been exceeded.

9,999 kilometres have been exceeded.

When 9,999 hours or 99,999 kilometres have

been exceeded, the trip computer is automati-

cally reset

From resetFrom reset.

Menus and submenus

203

On-board computer and displays

ECO display

The ECO display is not available in Mercedes-

AMG vehicles.

Press the = or ; button on the steering

wheel to select the

TripTrip menu.

Press the 9 or : button to select

ECOECO

DISPLAY

DISPLAY.

If the ignition remains switched off for longer

than four hours, the ECO display will be auto-

matically reset.

Further information on the ECO display

(Y page 159).

Displaying the range and current fuel

consumption

Mercedes-AMG vehicles: the menu only dis-

plays range :.

Press the = or ; button on the steering

wheel to select the

TripTrip menu.

Press 9 or : to select the display with

approximate range : and current fuel con-

sumption ;.

Approximate range : that can be covered is

calculated according to your current driving

style and the amount of fuel in the tank. If

there is only a small amount of fuel left in the

fuel tank, a vehicle being refuelled C

appears instead of approximate range :.

Recuperation display = shows you if energy

has been recuperated from the kinetic energy

in overrun mode and saved in the battery.

Recuperation display = depends on the

engine installed and is therefore not available

in all vehicles.

Digital speedometer

Press the = or ; button on the steering

wheel to select the

TripTrip menu.

Press the 9 or : button to select dig-

ital speedometer ;.

Gearshift recommendation : Z may also be

displayed.

Observe the information on gearshift recom-

mendation : for manual transmission

(Y page 143) or for automatic transmission

(shifting manually) (Y page 150).

Mercedes-AMG vehicles: a gearshift recom-

mendation is shown in the status bar of the

multifunction display and not in the digital

speedometer display.

Resetting values

Press the = or ; button on the steering

wheel to select the

TripTrip menu.

Press the 9 or : button to select the

function that you wish to reset.

Press a to confirm.

Press : to select

YesYes and press a to

confirm.

You can reset the values of the following func-

tions:

Trip meter

"From start" trip computer

"From reset" trip computer

ECO display

If you reset the values in the "ECO display", the

values in the "From start" trip computer are also

reset. If you reset the values in the "From start"

trip computer, the values in the "ECO display"

are also reset.

204

Menus and submenus

On-board computer and displays

Navigation menu

Displaying navigation instructions

In the NaviNavi menu, the multifunction display

shows the navigation instructions.

You can find further information on navigation in

the separate multimedia system operating

instructions.

Switch on the multimedia system; see sepa-

rate operating instructions.

Press the = or ; button on the steering

wheel to select the

NaviNavi menu.

Route guidance not active

Direction of travel

;

Current road

Route guidance active

No change of direction announced

Distance to the destination

;

Distance to the next change of direction

Current road

Symbol indicating "follow the road's course"

Change of direction without lane recom-

mendation

Road to which the change of direction leads

;

Distance to change of direction and visual

distance display

Change-of-direction symbol

When a change of direction is to be made, you

will see symbol = for the change of direction

and distance graphic ;. This shortens towards

the top of the display as you approach the point

of the announced change of direction. The

change of direction starts once the distance dis-

play reaches zero.

Change of direction announced with a

lane recommendation

Road to which the change of direction leads

;

Distance to change of direction and visual

distance display

Lanes not recommended

Recommended lane and new lane during a

change of direction

Change-of-direction symbol

On multi-lane roads, new lane recommenda-

tions can be displayed for the next change of

direction if the digital map supports this data.

During the change of direction, new lanes may

be added.

Lane not recommended =: you will not be able

to complete the next change of direction if you

stay in this lane.

Recommended lane and new lane during a

change of direction ?: in this lane you will be

able to complete the next two changes of direc-

tion without changing lane.

Menus and submenus

205

On-board computer and displays

Other status indicators of the naviga-

tion system

The navigation system displays additional infor-

mation and the vehicle status.

Possible displays

New route...New route... or Calculating route...Calculating route...

A new route is calculated.

Road not mappedRoad not mapped

The vehicle position is inside the area of the

digital map but the road is not recognised, e.g.

new roads, car parks or private land.

No routeNo route

No route could be calculated to the selected

destination.

You have reached the destination or a stop-

over.

Audio menu

Selecting a radio station

Active station list

;

Station with preset position

The multifunction display shows station ; with

station frequency or station name. The preset

position is only displayed in addition if station ;

has been stored.

Switch on the multimedia system and select

radio; see the separate operating instruc-

tions.

Press the = or ; button on the steering

wheel to select the

AudioAudio menu.

To select a preset list or station list: press

and briefly hold the 9 or : button until

the preset list or station list in the desired

frequency range is shown.

To select a station: briefly press 9

or :.

DAB radio mode (Digital Audio Broadcast-

ing) is an optimised digital transmission

standard designed for the mobile reception of

radio transmissions.

Audio player or audio media operation

Current track

Audio files from various audio players or media

can be played, depending on the equipment fit-

ted in the vehicle.

Switch on the multimedia system and activate

audio CD or MP3 mode; see the separate

operating instructions.

Press the = or ; button on the steering

wheel to select the

AudioAudio menu.

To select the next/previous track: briefly

press the 9 or : button.

To select a track from the track list (rapid

scrolling): press and hold the 9 or :

button until the desired track appears.

If you press and hold the 9 or : button,

the rapid scrolling speed is increased. Not all

audio players or media support this function.

If track information is saved on the audio player

or media, the multifunction display will show the

number and title of the track.

DVD-Video operation

206

Menus and submenus

On-board computer and displays

Only for vehicles with COMAND Online: you can

use the

AudioAudio menu to play video DVDs.

Switch on COMAND Online and select video

DVD (see the separate operating instruc-

tions).

Press the = or ; button on the steering

wheel to select the

AudioAudio menu.

To select the next or previous scene:

briefly press the 9 or : button.

To select a scene from the scene list

(rapid scrolling): press and hold the 9

or : button until desired scene :

appears.

Telephone menu

Introduction

WARNING

Operating the integrated information systems

and communications equipment in the vehicle

while driving will distract you from traffic con-

ditions. You could then lose control of the

vehicle. There is a risk of an accident.

Only operate these devices if road traffic con-

ditions permit. If you are unsure about the

surrounding conditions, pull over to a safe

location and make entries only while the vehi-

cle is stationary.

When telephoning, you must observe the legal

requirements for the country in which you are

currently driving.

Switch on the mobile phone, see the manu-

facturer's operating instructions.

Switch on the multimedia system; see sepa-

rate operating instructions.

Insert the mobile phone into the mobile phone

bracket (Y page 277).

Establish a Bluetooth

connection to the mul-

timedia system; see the separate operating

instructions.

Establish a Bluetooth

connection to the mul-

timedia system; see the separate operating

instructions.

Press the = or ; button on the steering

wheel to select the

TelTel menu.

You will see one of the following display mes-

sages in the multifunction display:

Telephone readyTelephone ready or the name of the net-

work provider: the mobile phone has found a

network and is ready to receive.

TelephoneTelephone NoNo serviceservice: there is no network

available or the mobile phone is searching for

a network.

i You can obtain further information about

suitable mobile phones and connecting

mobile phones via Bluetooth

at any Mercedes-Benz Service Centre

on the Internet at

Accepting a call

If someone calls you when you are in the TelTel

menu, a display message appears in the multi-

function display.

You can accept a call at any time, even if you are

not in the

TelTel menu.

Press the 6 button on the steering wheel

to accept an incoming call.

Rejecting or ending a call

You can reject or end a call any time even if you

are not in the

TelTel menu.

Press the ~ button on the steering wheel

to reject or end an incoming call.

Selecting an entry in the phone book

Press the = or ; button on the steering

wheel to select the

TelTel menu.

Press the 9, : or a button to

switch to the phone book.

Authorise access to the phone book on the

phone.

Press the 9 or : button to select the

desired name.

To begin rapid scrolling: press and hold the

9 or : button for longer than one sec-

ond.

Rapid scrolling stops when you release the

button or reach the end of the list.

Menus and submenus

207

On-board computer and displays

If only one telephone number is stored for

a name: press the 6 or a button to

start dialling.

If there is more than one number for a

particular name:press the 6 or a

button to display the numbers.

Press the 9 or : button to select the

number you want to dial.

Press the 6 or a button to start dial-

ling.

If you do not want to make the call: press

the ~ or % button.

Redialling

The on-board computer saves the last names or

numbers dialled in the redial memory.

Press the = or ; button on the steering

wheel to select the

TelTel menu.

Press the 6 button to switch to the redial

memory.

Press the 9 or : button to select the

desired name or number.

Press the 6 or a button to start dial-

ling.

If you do not want to make the call: press

the ~ or % button.

Assistance menu

Introduction

Depending on the equipment fitted in the vehi-

cle, you have the following options in the

Assist.Assist. menu:

Showing the assistance graphic

(Y page 208)

Activating/deactivating the Traffic Sign

Assist message function (Y page 208)

Deactivating/activating ESP

(except

Mercedes‑AMG vehicles) (Y page 209)

Activating/deactivating Active Brake Assist

(Y page 209)

Activating/deactivating ATTENTION ASSIST

(Y page 209)

Activating/deactivating Blind Spot Assist

(Y page 209)

Activating/deactivating Lane Keeping Assist

(Y page 209)

Showing the assistance graphic

Press the = or ; button on the steering

wheel to select the

Assist.Assist. menu.

Press 9 or : to select

Assist.Assist.

graphic

graphic.

Press a to confirm.

The multifunction display shows the distance

display of Distance Pilot DISTRONIC in the

assistance graphic.

The assistance graphic shows you the status

of and/or information from the following driv-

ing systems or driving safety systems:

Traffic Sign Assist (Y page 190)

Distance Pilot DISTRONIC (Y page 167)

Active Brake Assist (Y page 67)

ATTENTION ASSIST (Y page 189)

Lane Keeping Assist (Y page 193)

Press : to display the ATTENTION ASSIST

assessment.

Traffic Sign Assist

In the Traffic Sign AssistTraffic Sign Assist menu, you can

switch the Traffic Sign Assist message function

on or off. When the message function is activa-

ted, detected traffic signs and information

appear in the multifunction display for five sec-

onds.

Press the = or ; button on the steering

wheel to select the

Assist.Assist. menu.

Press the 9 or : button to select

Traffic Sign AssistTraffic Sign Assist.

Press a to confirm.

The current selection appears.

To activate/deactivate the message func-

tion: press a again.

208

Menus and submenus

On-board computer and displays

Further information about Traffic Sign Assist

(Y page 190).

Activating/deactivating ESP

Observe the important safety notes on ESP

(Y page 70).

WARNING

If you deactivate ESP

, ESP

no longer sta-

bilises the vehicle. There is an increased risk

of skidding and an accident.

Only deactivate ESP

in the situations descri-

bed in the following.

It may be best to deactivate ESP

in the follow-

ing situations:

when using snow chains

in deep snow

on sand or gravel

Deactivating/activating ESP

on Mercedes-

AMG vehicles (Y page 71).

For further information about ESP

, see

(Y page 69).

Start the engine.

Press the = or ; button on the steering

wheel to select the

Assist.Assist. menu.

Press 9 or : to select

ESPESP.

Press a to confirm.

The current selection appears.

To activate/deactivate: press a again.

ESP

is deactivated if the å warning lamp

in the instrument cluster lights up continu-

ously when the engine is running.

If the ÷ and å warning lamps light up

continuously, ESP

is not available due to a mal-

function.

Observe the information on warning lamps

(Y page 252).

Observe the information on display messages

(Y page 217).

Activating/deactivating Active Brake

Assist

Press the = or ; button on the steering

wheel to select the

Assist.Assist. menu.

Press the 9 or : button to select

Brake AssistBrake Assist.

Press a to confirm.

The current selection appears.

To activate/deactivate: press a again.

When Active Brake Assist is deactivated, the

æ symbol appears in the multifunction dis-

play in the assistance graphic display.

Further information on Active Brake Assist

(Y page 67).

Activating/deactivating ATTENTION

ASSIST

Press the = or ; button on the steering

wheel to select the

Assist.Assist. menu.

Press the 9 or : button to select

Attention AssistAttention Assist.

Press a to confirm.

The current selection appears.

Press a to confirm.

Press the : or 9 button to set

OffOff,

StandardStandard or SensitiveSensitive.

Press the a button to save the setting.

When ATTENTION ASSIST is deactivated, the

é symbol appears in the multifunction dis-

play in the assistance graphic display.

For further information about ATTENTION

ASSIST, see (Y page 189).

Activating/deactivating Blind Spot

Assist

Press the = or ; button on the steering

wheel to select the

Assist.Assist. menu.

Press the 9 or : button to select

Blind Spot AssistBlind Spot Assist.

Press a to confirm.

The current selection appears.

To activate/deactivate: press a again.

Further information about Blind Spot Assist

(Y page 192).

Activating/deactivating Lane Keeping

Assist

Press the = or ; button on the steering

wheel to select the

Assist.Assist. menu.

Press the 9 or : button to select

Lane Keeping AssistLane Keeping Assist.

Press a to confirm.

The current selection appears.

Press a again to confirm.

Menus and submenus

209

On-board computer and displays

Press the : or 9 button to set

OffOff,

StandardStandard or AdaptiveAdaptive.

Press the a button to save the setting.

When Lane Keeping Assist is activated, the

multifunction display shows the lane mark-

ings as bright lines in the assistance graphic.

For further information about Lane Keeping

Assist, see (Y page 193).

Service menu

Depending on the equipment fitted in the vehi-

cle, you have the following options in the

Serv.Serv.

menu:

Calling up display messages in the message

memory (Y page 216)

Restarting the tyre pressure loss warning sys-

tem (Y page 315)

Calling up the service due date

(Y page 285)

Settings menu

Introduction

Depending on the equipment fitted in the vehi-

cle, in the

SettingsSettings menu you have the follow-

ing options:

Changing the instrument cluster settings

Changing the light settings

Changing the vehicle settings

Changing the heating settings

Changing the convenience settings

Restoring the factory settings

Instrument cluster

Selecting the unit of measurement for dis-

tance

The

Display unit Speed-/odometer:Display unit Speed-/odometer: func-

tion allows you to choose whether certain dis-

plays appear in kilometres or miles in the mul-

tifunction display.

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

Instrument clusterInstrument cluster submenu.

Press a to confirm.

Press the : or 9 button to select the

Display unit Speed-/odometerDisplay unit Speed-/odometer function.

You will see the selected setting:

kmkm or milesmiles.

Press the a button to save the setting.

The selected unit of measurement for distance

applies to the following:

digital speedometer in the

TripTrip menu

total distance recorder and the trip meter

trip computer

current fuel consumption and approximate

range

navigation instructions in the

NaviNavi menu

cruise control

speed limiter

Distance Pilot DISTRONIC

ASSYST PLUS service interval display

Switching the additional speedometer

on/off

United Kingdom: this function is unavailable.

If the additional speedometer is switched on,

the speed is shown in the status bar of the mul-

tifunction display instead of the outside tem-

perature.

The speed display is inverse to your speedome-

ter.

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

Instrument clusterInstrument cluster submenu.

Press a to confirm.

Press the : or 9 button to select the

Dig. speedo [mph]Dig. speedo [mph] function.

You will see the selected setting:

onon or offoff.

Press the a button to save the setting.

Selecting permanent display

United Kingdom: this function is unavailable.

The

Permanent display:Permanent display: function allows you

to choose whether the multifunction display

always shows the outside temperature or the

speed.

The speed display is inverse to your speedome-

ter.

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

Instrument clusterInstrument cluster submenu.

Press a to confirm.

210

Menus and submenus

On-board computer and displays

Press the : or 9 button to select the

Permanent display:Permanent display: function.

The current setting,

outside temperatureoutside temperature

or Dig. speedo [mph]:Dig. speedo [mph]:, appears.

Press the a button to save the setting.

Lights

Switching the daytime driving lights

on/off

The

Daytime driving lightsDaytime driving lights function can

only be switched on with the engine turned off.

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

LightsLights submenu.

Press a to confirm.

Press the : or 9 button to select the

Daytime driving lightsDaytime driving lights function.

If the

DaytimeDaytime drivingdriving lightslights function has

been switched on, the cone of light and the

W symbol in the multifunction display are

shown in orange.

Press the a button to save the setting.

Further information on daytime driving lights

(Y page 107).

Vehicle

Setting permanent SPEEDTRONIC

You can set the permanent limiter using the

Limit speed (winter tyres):Limit speed (winter tyres): function.

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

VehicleVehicle submenu.

Press a to confirm.

Press : or 9 to select the

LimitLimit

speed (winter tyres):

speed (winter tyres): function.

You will see the current setting.

Press a to confirm.

Press the : or 9 button to adjust the

permanent speed limiter in increments of ten

(

160 km/h160 km/h to 240 km/h240 km/h). The OffOff setting

switches the permanent speed limiter off.

Press the a button to store the entry.

Further information on the permanent speed

limiter (Y page 166).

Activating/deactivating the automatic

locking feature

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

VehicleVehicle submenu.

Press a to confirm.

Press the : or 9 button to select the

Automatic door locksAutomatic door locks function.

If the

Automatic door locksAutomatic door locks function is

switched on, the multifunction display shows

the doors in orange.

Press the a button to save the setting.

If you activate the

Automatic door locksAutomatic door locks

function, the vehicle is centrally locked above a

speed of around 15 km/h.

For further information on the automatic locking

feature; see (Y page 85).

Activating/deactivating the acoustic

locking confirmation

If you switch on the AcousticAcoustic LockLock function, an

acoustic signal sounds when you lock the vehi-

cle.

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

VehicleVehicle submenu.

Press a to confirm.

Press the : or 9 button to select the

Acoustic LockAcoustic Lock function.

If the

Acoustic LockAcoustic Lock function is activated,

the & symbol in the multifunction display

lights up orange.

Press the a button to save the setting.

Heating

Auxiliary heating departure time

DANGER

If the exhaust pipe is blocked or sufficient

ventilation is not possible, toxic exhaust

fumes can enter the vehicle, especially car-

bon monoxide. This is the case, e.g. in

enclosed spaces, or if the vehicle is stuck in

snow. There is a risk of fatal injuries.

You should switch off the auxiliary heating in

enclosed spaces which do not have an extrac-

Menus and submenus

211

On-board computer and displays

tion system, e.g. a garage. If the vehicle is

stuck in snow and you must leave the auxiliary

heating running, keep the exhaust pipe and

the area around the vehicle clear of snow. To

guarantee a sufficient supply of fresh air, open

a window on the side of the vehicle away from

the wind.

WARNING

When the auxiliary heating is switched on,

parts of the vehicle can become very hot.

Flammable materials such as leaves, grass or

twigs may ignite if they come into contact

with:

hot parts of the exhaust system

the exhaust gas itself

There is a risk of fire.

When the auxiliary heating is switched on,

make sure that:

no flammable materials come into contact

with hot vehicle components

the exhaust gas can escape from the

exhaust pipe unhindered

the exhaust gas does not come into contact

with flammable materials.

Operating the auxiliary heating/ventilation

draws on the vehicle battery. After you have

heated or ventilated the vehicle a maximum of

two times, drive for a longer distance.

Only vehicles with auxiliary heating have this

function.

In the

HeatingHeating submenu, you can select a

stored departure time or change a departure

time.

The auxiliary heating timer function calculates

the switch-on time according to the outside

temperature so that the vehicle is preheated by

the departure time. When the departure time is

reached, the auxiliary heating continues to heat

for a further five minutes and then switches off.

The auxiliary heating adopts the set air condi-

tioning or THERMOTRONIC temperature set-

ting.

You can switch off the auxiliary heating by using

the remote control or the auxiliary heating but-

ton on the centre console.

Switch the auxiliary heating on regularly

once a month for about ten minutes.

Further information on auxiliary heating

(Y page 126).

Selecting the departure time or deactivat-

ing a selected departure time

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

HeatingHeating submenu.

Press a to confirm.

The current setting appears.

Press a again.

Press the : or 9 button to select one

of the three departure times or

TimerTimer offoff (no

timer active).

Press a to confirm.

If a departure time is selected, the yellow

indicator lamp lights up on the auxiliary heat-

ing button.

Changing the departure time

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

HeatingHeating submenu.

Press a to confirm.

The current setting appears.

Press the : or 9 button to select

Change AChange A, Change BChange B or Change CChange C.

Press a to confirm.

You can now change the departure time.

Press the = or ; button to select the

display to be changed: hours, minutes.

Press the : or 9 button to set the

selected display.

Press the a button to store the entry.

The yellow indicator lamp on the auxiliary

heating button lights up.

Comfort

Switching belt adjustment on/off

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

ConvenienceConvenience submenu.

Press a to confirm.

212

Menus and submenus

On-board computer and displays

Press the : or 9 button to select the

Belt adjustmentBelt adjustment function.

When the

Belt adjustmentBelt adjustment function is acti-

vated, the seat belt is displayed in orange in

the multifunction display.

Press the a button to save the setting.

For further information on belt adjustment, see

(Y page 43).

Switching the fold mirrors in when lock-

ing function on/off

This function is only available when the vehicle is

equipped with the electrical fold-in function.

When you activate the

Auto. fold-in mir‐Auto. fold-in mir‐

rors

rors function, the exterior mirrors are folded in

when the vehicle is locked. When you unlock the

vehicle and then open the driver's or front-

passenger door, the exterior mirrors fold out

again.

If you have switched on the Auto. fold-inAuto. fold-in

mirrors

mirrors function and you fold in the exterior

mirrors using the button on the door

(Y page 104), they will not fold out automati-

cally. The exterior mirrors can then only be fol-

ded out using the button on the door.

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

ConvenienceConvenience submenu.

Press a to confirm.

Press the : or 9 button to select the

Auto. fold-in mirrorsAuto. fold-in mirrors function.

If the

Auto. fold-in mirrorsAuto. fold-in mirrors function is

switched on, the multifunction display shows

the exterior mirror in orange.

Press the a button to save the setting.

Resetting to factory settings

Press the = or ; button on the steering

wheel to select the

SettingsSettings menu.

Press the : or 9 button to select the

Factory settingFactory setting submenu.

Press a to confirm.

The

Reset all settings?Reset all settings? function

appears.

Press the : or 9 button to select

NoNo or

YesYes.

Press the a button to confirm the selec-

tion.

If you have selected

YesYes, the multifunction

display shows a confirmation message.

For safety reasons, not all functions are reset:

the

LimitLimit speedspeed (winter(winter tyres)tyres) function of

the permanent speed limiter can only be set in

the

VehicleVehicle submenu.

AMG menu (Mercedes-AMG vehicles)

Warm-up

Digital speedometer

;

Gear indicator

Upshift indicator

Engine oil temperature

Coolant temperature

Transmission oil temperature

Press the = or ; button on the steering

wheel to select the

AMGAMG menu.

Upshift indicator: upshift indicator

UPUP =

indicates that the engine has reached the

overrevving range when in the manual drive

program.

Engine and transmission oil temperature:

when the engine and transmission are at nor-

mal operating temperature, oil tempera-

ture ? and B are displayed in white in the

multifunction display.

If the multifunction display shows oil temper-

ature ? or B in blue, the engine or the

transmission are not yet at normal operating

temperature. Avoid using the full output of the

engine during this time.

Menus and submenus

213

On-board computer and displays

SETUP

Drive system

ComfortComfort/SportSport/Sport +Sport +

;

Suspension

ComfortComfort/SportSport/Sport +Sport +

Transmission

DD/MM

ESP

OnOn/OffOff or SPORT handling mode

SportSport

SETUP displays the following information and

functions:

the digital speedometer

the gear indicator

the drive system setting

the suspension mode

the transmission position

the ESP

(Electronic Stability Program) status

Press the = or ; button on the steering

wheel to select the

AMGAMG menu.

Press 9 repeatedly until SETUP appears.

RACE TIMER

Displaying and starting the RACETIMER

Lap

;

RACETIMER

The RACETIMER is only intended for use on a

closed race circuit. Do not use the function on

public roads.

You can start the RACETIMER when the engine is

running or if the key is in position 2 in the ignition

lock.

Press the = or ; button on the steering

wheel to select the

AMGAMG menu.

Press the 9 button repeatedly until the

RACETIMER appears.

To start: press the a button to start the

RACETIMER.

Displaying the intermediate time

Press the = or ; button to select

Interm. TimeInterm. Time.

Press a to confirm.

The intermediate time is shown for five sec-

onds.

Starting a new lap

RACETIMER

;

Fastest lap time (best lap)

Lap

Press a to confirm

New LapNew Lap.

A maximum of 16 laps may be stored. The

16th lap can only be completed with

FinishFinish

Lap

Lap.

Stopping the RACETIMER

214

Menus and submenus

On-board computer and displays

Press the % button on the steering wheel.

Confirm

YesYes with a.

The RACETIMER interrupts timing if you stop the

vehicle and turn the key to position 1 in the igni-

tion lock. If you turn the key to position 3 and

then press a to confirm

StartStart, timing is

continued.

Resetting the current lap

Stop the RACETIMER.

Press the = or ; button to select

Reset LapReset Lap.

Press a to reset the lap time to "0".

Deleting all laps

If you switch off the engine, the RACETIMER is

reset to "0" after 30 seconds. All laps are

deleted.

You cannot delete individual stored laps. If you

have stopped 16 laps, the current lap does not

have to be reset.

Reset the current lap.

Press a to confirm

ResetReset.

Reset Race Timer?Reset Race Timer? appears in the multi-

function display.

Press the : button to select

YesYes and press

the a button to confirm.

All laps are deleted.

Overall evaluation

RACETIMER overall evaluation

;

Total time driven

Average speed

Distance covered

Maximum speed

This function is shown if you have stored at least

one lap and stopped the RACETIMER.

Press = or ; on the steering wheel to

select the

AMGAMG menu.

Press the 9 button repeatedly until the

overall evaluation appears.

Lap evaluation

Lap

;

Lap time

Average lap speed

Lap length

Top speed during lap

This function is only available if you have stored

at least two laps and have stopped the RACE-

TIMER.

Press the = or ; button on the steering

wheel to select the

AMGAMG menu.

Press the 9 button repeatedly until a lap

evaluation appears.

Each lap is shown in a separate submenu. The

fastest lap is indicated by flashing symbol :.

Press the 9 or : button to select a dif-

ferent lap evaluation.

Menus and submenus

215

On-board computer and displays

On-board computer and displays -> Menus and submenus for Your Mercedes CLA 4 Door First Generation (2013-2018)

Related Topics

Popular Owner Manuals

Latest Owner Manuals