Get On-board computer and displays -> Menus and submenus Guide for Mercedes GLE SUV First Generation (2016-2019)

Menus and submenus

244

i Set the time via the multimedia system (see

Trip menu

the Digital Owner's Manual).

Standard display

Possible readings on the multifunction dis-

play:

On-board computer and displays

R Z Gearshift recommendation, when shifting

manually ( Y page 157)

R j Parking Pilot ( Y page 201)

R ¯ Cruise control ( Y page 177)

R LIM Limiter ( Y page 193)

R _ Adaptive Highbeam Assist Plus

( Y page 121)

X Press and hold the % button on the steer-

ing wheel until the Trip menu with trip

R è ECO start/stop function ( Y page 147)

meter : and total distance recorder ;

R ë HOLD function ( Y page 193)

appears.

R a Distance Pilot DISTRONIC Steering Pilot

( Y page 250)

R 120 km/h! Maximum permissible speed

Trip computer "From start" or "From

reset"

exceeded (for certain countries only)

R DSR Downhill Speed Regulation

( Y page 225)

Menus and submenus

Menu overview

Press the = or ; button on the steering

: Distance

wheel to call up the menu bar and select a menu.

; Driving time

Operating the on-board computer ( Y page 242).

= Average speed

Depending on the equipment fitted in the vehi-

? Average fuel consumption

cle, you can call up the following menus:

X Press the = or ; button on the steering

R Trip menu ( Y page 244)

wheel to select the Trip menu.

R Navi menu (navigation instructions)

X Press the 9 or : button to select

( Y page 245)

From start or From reset .

R Audio menu ( Y page 247)

The values in the From start submenu are cal-

R Tel menu (telephone) ( Y page 248)

culated from the start of a journey, whilst the

R Assist. menu (assistance) ( Y page 249)

values in the From reset submenu are calcu-

R Serv. menu ( Y page 251)

lated from the last time the submenu was reset

R Settings menu (settings) ( Y page 251)

( Y page 245).

The From start trip computer is automatically

R ON&OFFROAD menu ( Y page 255)

R AMG menu (Mercedes-AMG vehicles)

reset if:

R The ignition has been switched off for more

( Y page 255)

than four hours

R 999 hours have been exceeded.

R 9,999 kilometres have been exceeded.

The From reset trip computer is automatically

reset if the value exceeds 9,999 hours or

99,999 kilometres.

Menus and submenus

245

ECO display

X Press a to confirm your selection.

X Press : to select Yes and press a to

The ECO display is not available for Mercedes-

confirm.

AMG vehicles.

You can reset the values of the following func-

X Press the = or ; button on the steering

On-board computer and displays

tions:

wheel to select the Trip menu.

X Press the 9 or : button to select ECO

R Trip meter

DISPLAY .

R "From start" trip computer

R "From reset" trip computer

If the ignition remains switched off for longer

than four hours, the ECO display will be auto-

R ECO display

matically reset.

If you reset the values in the "ECO display", the

Further information on the ECO display

values in the "From start" trip computer are also

( Y page 169).

reset. If you reset the values in the "From start"

trip computer, the values in the "ECO display"

are also reset.

Displaying the range and current fuel

consumption

Navigation menu

Displaying navigation instructions

In the Navi menu, the multifunction display

shows navigation instructions.

You can find further information on navigation,

in the Digital Owner's Manual, under the multi-

media system.

Mercedes-AMG vehicles: the menu displays

only the approximate range :.

X Switch on the multimedia system (see the

Digital Owner's Manual)

X Press the = or ; button on the steering

wheel to select the Trip menu.

X Press the = or ; button on the steering

wheel to select the Navi menu.

Digital speedometer

Route guidance not active

X Press the = or ; button on the steering

wheel to select the Trip menu.

X Press the 9 or : button to select the

digital speedometer.

A gearshift recommendation Z can also be

displayed.

Observe the information on gearshift recom-

mendation Z when shifting manually

( Y page 157).

: Direction of travel

Mercedes-AMG vehicles: a gearshift recom-

; Current road

mendation is shown in the status bar of the

multifunction display and not in the digital

speedometer display.

Resetting values

X Press the = or ; button on the steering

wheel to select the Trip menu.

X Press the 9 or : button to select the

function that you wish to reset.

Menus and submenus

246

Route guidance active

? Recommended lane and new lane during a

change of direction

No change of direction announced

A Change-of-direction symbol

On multi-lane roads, new lane recommenda-

On-board computer and displays

tions can be displayed for the next change of

direction if the digital map supports this data.

During the change of direction, new lanes may

be added.

Lane not recommended =: you will not be able

to complete the next change of direction if you

stay in this lane.

: Distance to the destination

Recommended lane and new lane during a

; Distance to the next change of direction

change of direction ?: in this lane you will be

= Current road

able to complete the next two changes of direc-

? Symbol indicating "follow the road's course"

tion without changing lane.

Change of direction announced without a

Other status indicators of the naviga-

lane recommendation

tion system

: Road to which the change of direction leads

; Distance to change of direction and visual

The navigation system displays additional infor-

distance display

mation and the vehicle status.

= Change-of-direction symbol

Possible displays:

R New route... or Calculating route...

When a change of direction is to be made, you

will see symbol = for the change of direction

A new route is calculated.

and distance graphic ;. This shortens towards

R Road not mapped

the top of the display as you approach the point

The vehicle position is inside the area of the

of the announced change of direction. The

digital map but the road is not recognised, e.g.

change of direction starts once the distance dis-

new roads, car parks or private land.

play reaches zero.

R No route

Change of direction announced with a

No route could be calculated to the selected

lane recommendation

destination.

R O

You have reached the destination or an inter-

mediate destination.

: Road to which the change of direction leads

; Distance to change of direction and visual

distance display

= Lanes not recommended

Menus and submenus

247

Audio files from various audio players or media

Audio menu

can be played, depending on the equipment fit-

Selecting a radio station

ted in the vehicle.

X Switch on the multimedia system and select

On-board computer and displays

CD or MP3 mode (see the Digital Owner's

Manual).

X Press the = or ; button on the steering

wheel to select the Audio menu.

X To select the next/previous track: briefly

press the 9 or : button.

X To select a track from the track list (rapid

: Active station list

scrolling): press and hold the 9 or :

; Station with preset position

button until desired track : has been

reached.

The multifunction display shows the station ;

with station frequency or station name. The pre-

If you press and hold the 9 or : button,

set position is only displayed in addition if the

the rapid scrolling speed is increased. Not all

station ; has been stored. You can store sta-

audio players or media support this function.

tions ; in the multimedia system.

If track information is saved on the audio player

X Switch on the multimedia system and select

or media, the multifunction display will show the

radio (see the Digital Owner's Manual).

number and title of the track. The current track

X Press the = or ; button on the steering

does not appear in audio AUX mode (Auxiliary

wheel to select the Audio menu.

audio mode: external audio source connected).

X To select a preset list or station list: press

Video DVD operation

and briefly hold the 9 or : button until

the preset list or station list in the desired

frequency range is shown on the multifunc-

tion display.

X To select a station: briefly press 9

or :.

i DAB radio mode (Digital Audio Broadcast-

ing) is an optimised digital transmission

standard designed for the mobile reception of

X Switch on the multimedia system and select

radio transmissions.

video DVD (see the Digital Owner's Manual).

X Press the = or ; button on the steering

Operating the audio player or audio

wheel to select the Audio menu.

media

X To select the next or previous scene:

briefly press the 9 or : button.

X To select a scene from the scene list

(rapid scrolling): press and hold the 9

or : button until the desired scene : has

been reached.

Menus and submenus

248

Operating the TV

X Switch on the mobile phone (see the manu-

facturer's operating instructions).

X Switch on the multimedia system (see the

Digital Owner's Manual)

On-board computer and displays

X Insert the mobile phone into the bracket

( Y page 328).

X Establish a Bluetooth ® connection to the mul-

timedia system (see Digital Owner's Manual).

The preset position is only displayed along with

X Press the = or ; button on the steering

wheel to select the Tel menu.

channel : if this has been saved. You can save

channels in the multimedia system.

You will see one of the following display mes-

X Switch on the multimedia system and select

sages on the multifunction display:

TV (see the Digital Owner's Manual).

R Telephone ready or the name of the net-

X Press the = or ; button on the steering

work provider: the mobile phone has found a

wheel to select the Audio menu.

network and is ready to receive.

X To select a saved channel: briefly press the

R Telephone No service : there is no network

9 or : button.

available or the mobile phone is searching for

X To select a channel from the channel list:

a network.

press and briefly hold the 9 or : but-

i You can obtain further information on suit-

ton.

able mobile phones and connecting mobile

i Depending on the digital TV broadcaster,

phones via Bluetooth ® :

radio stations can also be received. The mul-

tifunction display shows TV (Radio) .

R at any Mercedes-Benz Service Centre

R on the internet at

Telephone menu

Accepting a call

Introduction

If someone calls you when you are in the Tel

G WARNING

menu, a display message appears in the multi-

function display.

If you operate information and communica-

You can accept a call at any time irrespective of

tion equipment integrated in the vehicle when

the selected menu.

driving, you could be distracted from the traf-

X Press the 6 button on the steering wheel

fic situation. This could also cause you to lose

to accept an incoming call.

control of the vehicle. There is a risk of an

accident.

Rejecting or ending a call

Only operate this equipment when the traffic

situation permits. If you cannot be sure of this,

You can end or reject a call even if you are not in

the Tel menu.

stop the vehicle paying attention to road and

traffic conditions and operate the equipment

X Press the ~ button on the steering wheel

to reject or end an incoming call.

with the vehicle stationary.

When using the phone, you must observe the

legal requirements for the country in which you

are currently driving.

Menus and submenus

249

Selecting an entry from the telephone

Assistance menu

book

Introduction

X Press the = or ; button on the steering

wheel to select the Tel menu.

Depending on the equipment fitted in the vehi-

On-board computer and displays

cle, you have the following options in the

X Press the 9, : or a button to

Assist. menu:

switch to the phone book.

R Showing the assistance graphic

X Authorise access to the phone book on the

( Y page 249)

phone.

R Activating/deactivating the Traffic Sign

X Press the 9 or : button to select the

Assist display ( Y page 250)

desired name.

R Activating/deactivating Steering Pilot

( Y page 250)

X To start rapid scrolling: press and hold 9

R Activating/deactivating Active Brake Assist

or : for longer than one second.

( Y page 250)

Rapid scrolling stops when you release the

R Activating/deactivating Active Brake Assist

button or reach the end of the list.

with cross-traffic function ( Y page 250)

X If only one telephone number is stored for

R Activating/deactivating ATTENTION ASSIST

a name: press the 6 or a button to

( Y page 250)

start dialling.

R Activating/deactivating Blind Spot Assist or

Active Blind Spot Assist ( Y page 250)

X If there is more than one number for a

R Activating/deactivating Lane Keeping Assist

particular name: press the 6 or a

or Active Lane Keeping Assist ( Y page 251)

button to display the numbers.

X Press the 9 or : button to select the

Showing the assistant display

number you want to dial.

X Press the 6 or a button to start dial-

ling.

X To exit the telephone book: press the ~

or % button.

Redialling

X Press the = or ; button on the steering

The on-board computer saves the last names or

wheel to select the Assist. menu.

numbers dialled in the redial memory.

X Press 9 or : to select Assistance

X Press the = or ; button on the steering

graphic .

wheel to select the Tel menu.

X Confirm by pressing a on the steering

X Press the 6 button to switch to the redial

wheel.

memory.

The multifunction display shows the Distance

X Press the 9 or : button to select the

Pilot DISTRONIC distance display in the assis-

desired name or number.

tance graphic display.

X Press the 6 or a button to start dial-

The assistance graphic shows you the status

ling.

of and/or information from the following driv-

ing systems or driving safety systems:

X To exit the redial memory: press the ~

R Traffic Sign Assist ( Y page 215)

or % button.

R Distance Pilot DISTRONIC ( Y page 181)

R Active Brake Assist ( Y page 71)

R Active Brake Assist with cross-traffic func-

tion ( Y page 77)

R ATTENTION ASSIST ( Y page 213)

Menus and submenus

250

R Lane Keeping Assist ( Y page 218) or Active

the Driving Assistance package, to activate or

Lane Keeping Assist ( Y page 222)

deactivate Active Brake Assist with cross-traffic

function.

R DSR ( Y page 225)

X Press the = or ; button on the steering

R Off-road program (vehicles with Off-Road

wheel to select the Assist. menu.

On-board computer and displays

Engineering package) ( Y page 227)

X Press the 9 or : button to select

R Rear window wiper ( Y page 125)

Brake Assist .

X Press : to display the ATTENTION ASSIST

X Press a to confirm.

assessment.

The current selection appears.

X To activate/deactivate: press a again.

Traffic Sign Assist

When Active Brake Assist or Active Brake

In the Traffic Sign Assist menu, you can

Assist with cross-traffic function is deactiva-

ted, the æ symbol appears in the multi-

switch the Traffic Sign Assist message function

function display in the assistance graphic dis-

on or off. When the message function is activa-

play.

ted, detected traffic signs and information

appear in the multifunction display for five sec-

Further information on Active Brake Assist

onds.

( Y page 71) and Active Brake Assist with cross-

X Press the = or ; button on the steering

traffic function ( Y page 77).

wheel to select the Assist. menu.

X Press the 9 or : button to select

Activating/deactivating ATTENTION

Traffic Sign Assist .

ASSIST

X Confirm by pressing a on the steering

X Press the = or ; button on the steering

wheel.

wheel to select the Assist. menu.

The current selection appears.

X Press the 9 or : button to select

X To activate/deactivate the message func-

Attention Assist .

tion: press a again.

X Press the a button.

Further information about Traffic Sign Assist

The current selection appears.

( Y page 215).

X Press a to confirm.

X Press the : or 9 button to set Off ,

Activating/deactivating Steering Pilot

Standard or Sensitive .

X Press the = or ; button on the steering

X Press the a button to save the setting.

wheel to select the Assist. menu.

When ATTENTION ASSIST is deactivated, the

X Press 9 or : to select Steering

é symbol appears in the multifunction dis-

Pilot .

play in the assistance graphic display.

X Confirm by pressing a on the steering

For further information about ATTENTION

wheel.

ASSIST, see ( Y page 213).

The current selection appears.

X To activate/deactivate: press the a but-

Activating/deactivating Blind Spot

ton again.

Assist

When the Steering Pilot is activated, the mul-

tifunction display displays a Steering Pilot

X Press the = or ; button on the steering

On message.

wheel to select the Assist. menu.

X Press the 9 or : button to select

Further information about Distance Pilot

Blind Spot Assist .

DISTRONIC with Steering Pilot ( Y page 188).

X Confirm by pressing a on the steering

wheel.

Activating/deactivating Active Brake

The current selection appears.

Assist

X To activate/deactivate: press the a but-

You can use these functions to activate/deac-

ton again.

tivate Active Brake Assist or, on vehicles with

Menus and submenus

251

Further information about Blind Spot Assist

R Changing the instrument cluster settings

( Y page 216).

( Y page 251)

For further information about Active Blind Spot

R Changing the light settings ( Y page 252)

Assist, see ( Y page 219).

R Changing the vehicle settings ( Y page 253)

On-board computer and displays

R Changing the heating settings ( Y page 253)

Activating/deactivating Lane Keeping

R Changing the convenience settings

Assist

( Y page 254)

R Restoring the factory settings ( Y page 255)

X Press the = or ; button on the steering

wheel to select the Assist. menu.

Instrument cluster submenu

X Press the 9 or : button to select

Lane Keeping Assist .

Selecting the unit of measurement for dis-

X Press a to confirm.

tance

The current selection appears.

The Display unit Speed-/odometer: func-

X Press a to confirm.

X Press the : or 9 button to set Off ,

tion allows you to choose whether certain dis-

Standard or Adaptive .

plays appear in kilometres or miles in the mul-

tifunction display.

When Lane Keeping Assist or Active Lane

Keeping Assist is activated, the multifunction

X Press the = or ; button on the steering

wheel to select the Settings menu.

display shows the lane markings as bright

lines in the assistance graphic.

X Press the : or 9 button to select the

Instrument cluster submenu.

X Press the a button to save the setting.

X Press a to confirm.

Further information about Lane Keeping Assist

( Y page 218).

X Press the : or 9 button to select the

Display unit Speed-/odometer function.

Further information about Active Lane Keeping

You will see the selected setting: km or miles .

Assist ( Y page 222).

X Press the a button to save the setting.

The selected unit of measurement for distance

Service menu

applies to the following:

R Digital speedometer in the Trip menu

Introduction

R Total distance recorder and the trip meter

Depending on the equipment fitted in the vehi-

R Trip computer

cle, you have the following options on the Ser‐

R Current consumption and the range

vice menu:

R Navigation instructions in the Navi menu

R call up display messages in the message

R Cruise control

memory ( Y page 258)

R Speed limiter

R restart the tyre pressure loss warning system

R Distance Pilot DISTRONIC

( Y page 372) or check the tyre pressure elec-

tronically ( Y page 373)

R ASSYST PLUS service interval display

R call up the service due date ( Y page 341)

Selecting permanent display

United Kingdom: this function is unavailable.

The Permanent display: function allows you

Settings menu

to choose whether the multifunction display

Introduction

always shows the outside temperature or the

speed.

Depending on the equipment fitted in the vehi-

The speed display is inverse to your speedome-

cle, you have the following options on the Set‐

ter.

tings menu:

Menus and submenus

252

X Press the = or ; button on the steering

R Motorway mode

wheel to select the Settings menu.

R Active light function

X Press the : or 9 button to select the

R Cornering light function

Instrument cluster submenu.

R Extended range foglamps

On-board computer and displays

X Confirm by pressing a on the steering

R Off-road lights

wheel.

If you set the dipped-beam headlamps for driv-

X Press the : or 9 button to select the

ing on the right/left, the multifunction display

Permanent display: function.

shows the Intell. Light System: system

The current setting, outside temperature

inoperative Inactive for left-side

or Dig. speedo [mph]: , appears.

traffic or Intell. Light System: system

inoperative Inactive for right-side

X To change the setting: press a again.

traffic display message instead of the

Intell. Light System function in the Lights

Light submenu

submenu ( Y page 252). This display message

will only appear if the setting for driving on the

Setting the daytime driving lights

left/right is set opposite to your vehicle's coun-

The Daytime driving lights function can

try version.

only be switched on with the engine turned off.

Further information on the Intelligent Light Sys-

X Press the = or ; button on the steering

tem ( Y page 120).

wheel to select the Settings menu.

Setting the dipped-beam headlamps for

X Press the : or 9 button to select the

Lights submenu.

driving on the left/right

This function is available only in vehicles with

X Press a to confirm.

the Intelligent Light System.

X Press the : or 9 button to select the

Daytime driving lights function.

You can use this function to switch between

If the Daytime driving lights function has

symmetrical and asymmetrical dipped beam

( Y page 117).

been switched on, the cone of light and the

W symbol in the multifunction display are

X Press the = or ; button on the steering

wheel to select the Settings menu.

shown in orange.

X Press the a button to save the setting.

X Press the : or 9 button to select the

Lights submenu.

Further information on daytime driving lights

( Y page 118).

X Press a to confirm.

X Press the : or 9 button to select the

Switching the Intelligent Light System

Dipped beams Setting for: function.

on/off

You will see the selected setting: Right-

side traffic or Left-side traffic .

X Press the = or ; button on the steering

wheel to select the Settings menu.

X Press a to save the setting.

X Press the : or 9 button to select the

If you change the setting, conversion does not

Lights submenu.

take place until the next time the engine is

started.

X Press a to confirm.

X Press the : or 9 button to select the

If you set the dipped-beam headlamps opposite

Intell. Light System function.

to your vehicle's country version for driving on

If the Intell. Light System function has

the right/left, then motorway mode and the

been switched on, the cone of light and the

extended range foglamps are unavailable.

L symbol in the multifunction display are

A qualified specialist workshop can set the

shown in orange.

dipped-beam headlamps for driving on the left/

X Press the a button to save the setting.

right.

When you switch the Intell. Light System

function on, you activate the following func-

tions:

Menus and submenus

253

Vehicle submenu

X Press the : or 9 button to select the

Acoustic Lock function.

If the Acoustic Lock function is activated,

Setting the permanent speed limiter

the & symbol in the multifunction display

X Press the = or ; button on the steering

lights up orange.

wheel to select the Settings menu.

On-board computer and displays

X Press the a button to save the setting.

X Press the : or 9 button to select the

Vehicle submenu.

Heating submenu

X Press a to confirm.

X Press : or 9 to select the Limit

speed (winter tyres): function.

Auxiliary heating departure time

You will see the current setting.

G DANGER

X Press a to confirm.

If the exhaust pipe is blocked or sufficient

X Press the : or 9 button to adjust the

ventilation is not possible, toxic exhaust

permanent speed limiter in increments of ten

(160 km/h to 240 km/h ). The Off setting

fumes can enter the vehicle, especially car-

bon monoxide. This is the case, e.g. in

switches the permanent speed limiter off.

enclosed spaces, or if the vehicle is stuck in

X Press a to store the entry.

snow. There is a risk of fatal injuries.

Further information on the permanent speed

You should switch off the auxiliary heating in

limiter ( Y page 181).

enclosed spaces which do not have an extrac-

Activating/deactivating the automatic

tion system, e.g. a garage. If the vehicle is

locking feature

stuck in snow and you must leave the auxiliary

If you activate the Automatic door locks

heating running, keep the exhaust pipe and

function, the vehicle is centrally locked above a

the area around the vehicle clear of snow. To

speed of approximately 15 km/h.

guarantee a sufficient supply of fresh air, open

X Press the = or ; button on the steering

a window on the side of the vehicle away from

wheel to select the Settings menu.

the wind.

X Press the : or 9 button to select the

Vehicle submenu.

G WARNING

X Press a to confirm.

When the auxiliary heating is switched on,

X Press the : or 9 button to select the

Automatic door locks function.

parts of the vehicle can become very hot.

When the Automatic door locks function is

Flammable materials such as leaves, grass or

activated, the vehicle doors are displayed in

twigs may ignite if they come into contact

orange in the multifunction display.

with:

X Press the a button to save the setting.

R hot parts of the exhaust system

For further information on the automatic locking

R the exhaust gas itself

feature; see ( Y page 90).

There is a risk of fire.

Activating/deactivating the acoustic

When the auxiliary heating is switched on,

locking confirmation

make sure that:

If you switch on the Acoustic Lock function, an

R no flammable materials come into contact

acoustic signal sounds when you lock the vehi-

cle.

with hot vehicle components

X Press the = or ; button on the steering

R the exhaust gas can escape from the

wheel to select the Settings menu.

exhaust pipe unhindered

X Press the : or 9 button to select the

R the exhaust gas does not come into contact

Vehicle submenu.

with flammable materials.

X Press a to confirm.

Menus and submenus

254

X Press a to confirm.

! Operating the auxiliary heating/ventilation

You can now change the departure time.

draws on the vehicle battery. After you have

heated or ventilated the vehicle a maximum of

X Press the = or ; button to select the

two times, drive for a longer distance.

display to be changed: hours, minutes.

On-board computer and displays

X Press the : or 9 button to set the

Only vehicles with auxiliary heating have this

selected display.

function.

In the Heating submenu, you can select a

X Press the a button to store the entry.

The yellow indicator lamp on the auxiliary

stored departure time or change a departure

heating button lights up.

time.

The auxiliary heating timer function calculates

the switch-on time according to the outside

Convenience submenu

temperature so that the vehicle is preheated by

the departure time. When the departure time is

Activating/deactivating the EASY-

reached, the auxiliary heating continues to heat

ENTRY/EXIT feature

for a further five minutes and then switches off.

G WARNING

The auxiliary heating adopts the THERMATIC or

THERMOTRONIC temperature setting.

When the EASY-ENTRY/EXIT feature adjusts

You can switch off the auxiliary heating by using

the steering wheel, you and other vehicle

the remote control or the auxiliary heating but-

occupants – particularly children – could

ton on the centre console.

become trapped. There is a risk of injury.

i Switch the auxiliary heating on regularly

While the EASY-ENTRY/EXIT feature is mak-

once a month for about ten minutes.

ing adjustments, make sure that no one has

Further information on auxiliary heating

any body parts in the sweep of the steering

( Y page 136).

wheel.

Selecting the departure time or deactivat-

If someone is trapped:

ing a selected departure time

R press one of the memory function position

X Press the = or ; button on the steering

buttons, or

wheel to select the Settings menu.

R move the switch for steering wheel adjust-

X Press the : or 9 button to select the

Heating submenu.

ment in the opposite direction to that in

which the steering wheel is moving.

X Press a to confirm.

The adjustment process is stopped.

You will see the selected setting.

X Press a to confirm.

X Press the = or ; button on the steering

X Press the : or 9 button to select one

wheel to select the Settings menu.

of the three departure times or Timer off (no

X Press the : or 9 button to select the

timer active).

Convenience submenu.

X Press a to confirm.

If a departure time is selected, the yellow

X Using : or 9, select the Easy Entry/

indicator lamp lights up on the auxiliary heat-

Exit function.

ing button.

If the Easy Entry/Exit function is activated,

Changing the departure time

the vehicle steering wheel is displayed in

orange in the multifunction display.

X Press the = or ; button on the steering

wheel to select the Settings menu.

X Press the a button to save the setting.

X Press the : or 9 button to select the

Further information on the EASY-ENTRY/EXIT

Heating submenu.

feature ( Y page 111).

X Press a to confirm.

You will see the selected setting.

X Press the : or 9 button to select A , B

or Change C .

Menus and submenus

255

Switching belt adjustment on/off

You can then only fold out the exterior mirrors

using button :.

X Press the = or ; button on the steering

wheel to select the Settings menu.

Resetting to factory settings

X Press the : or 9 button to select the

On-board computer and displays

Convenience submenu.

X Press the = or ; button on the steering

wheel to select the Settings menu.

X Press a to confirm.

X Press the : or 9 button to select the

Belt adjustment function.

Factory setting submenu.

If the Belt adjustment function is activated,

X Press a to confirm.

the vehicle seat belt is shown in orange in the

The Reset all settings? message

multifunction display.

appears.

X Press the a button to save the setting.

X Press the : or 9 button to select No or

Yes .

For further information on belt adjustment, see

( Y page 48).

X Press a to confirm the selection.

If you have selected Yes , the multifunction

Folding the mirrors in when activating/

display shows a confirmation message.

deactivating the locking function

For safety reasons, not all functions are reset:

This function is only available when the vehicle is

the Limit speed (winter tyres): function

equipped with the electrical fold-in function.

of the permanent speed limiter can only be set in

When you activate the Auto. fold-in mir‐

the Vehicle submenu.

rors function, the exterior mirrors are folded in

For safety reasons, the Daytime driving

when the vehicle is locked. The exterior mirrors

lights function in the Lights submenu is only

fold out automatically again as soon as you

reset if the engine is switched off.

unlock the vehicle.

X Press the = or ; button on the steering

wheel to select the Settings menu.

ON&OFFROAD menu

X Press the : or 9 button to select the

Convenience submenu.

X Press the = or ; button on the steering

wheel to select the ON&OFFROAD menu.

X Press a to confirm.

You can view the current off-road program set-

X Press the : or 9 button to select the

tings in the ON&OFFROAD menu:

Auto. fold-in mirrors function.

If the Auto. fold-in mirrors function is

R Vehicles with the Off-Road Engineering pack-

switched on, the multifunction display shows

age ( Y page 227)

the exterior mirror in orange.

R Vehicles without the Off-Road Engineering

X Press the a button to save the setting.

package ( Y page 226)

AMG menu (Mercedes-AMG vehicles)

Warm-up

If you have switched on the Auto. fold-in

mirrors function and you fold the exterior mir-

: Digital speedometer

; Gear indicator

rors in using button :, they will not fold out

automatically ( Y page 113).

= Upshift indicator

Menus and submenus

256

RACE TIMER

? Engine oil temperature

A Coolant temperature

Displaying and starting the RACE TIMER

B Transmission oil temperature

The RACE TIMER is intended only for use on a

X Press the = or ; button on the steering

On-board computer and displays

designated race track. Do not use the function

wheel to select the AMG menu.

on public roads.

Upshift indicator: upshift indicator Up =

indicates that the engine has reached the

overrevving range when in the manual drive

program.

Engine/transmission oil temperature:

when the engine and transmission are at nor-

mal operating temperature, oil tempera-

ture ? and B are displayed in white in the

multifunction display.

: Lap

If the multifunction display shows oil temper-

; RACE TIMER

ature ? or B in blue, the engine or the

You can start the RACETIMER when the engine is

transmission are not yet at normal operating

running or if the key is in position 2 in the igni-

temperature. Avoid using the full output of the

tion lock.

engine during this time.

X Press = or ; on the steering wheel to

select the AMG menu.

SETUP

X Press the 9 button repeatedly until the

RACETIMER is shown.

X To start: press a to start the RACE TIMER.

Displaying the intermediate time

: Engine mode (Comfort /Sport /Sport + )

; Suspension setting Comfort /Sport /

Sport +

= Transmission position D /M

? ESP ® mode (ON /OFF )

X Press the = or ; button to select

SETUP displays the following information/func-

Interm. Time .

tions:

X Press a to confirm.

R digital speedometer

The intermediate time is displayed for five

R gear indicator

seconds.

R the engine mode

R suspension mode

R transmission position

R the ESP ® (Electronic Stability Program) mode

X Press the = or ; button on the steering

wheel to select the AMG menu.

X Press the 9 button repeatedly until SETUP

is displayed.

Menus and submenus

257

Starting a new lap

You cannot delete individual stored laps. If you

have stopped 16 laps, the current lap does not

have to be reset.

X Reset the current lap.

X Press a to confirm Reset .

On-board computer and displays

Reset Race Timer? appears in the multi-

function display.

X Press : Yes to select and confirm with

: RACE TIMER

All laps are deleted.

; Fastest lap time (best lap)

= Lap

Overall evaluation

X Press a to confirm New Lap .

i A maximum of 16 laps may be stored. The

16th lap can only be completed with Finish

Lap .

Stopping the RACE TIMER

: RACETIMER overall evaluation

; Total time driven

= Average speed

? Distance covered

A Maximum speed

This function is shown if you have stored at least

X Press the % button on the steering wheel.

one lap and stopped the RACETIMER.

X Confirm Yes with a.

X Press = or ; on the steering wheel to

select the AMG menu.

The RACETIMER interrupts timing if you stop the

vehicle and turn the key to position 1 in the

X Press the 9 button repeatedly until the

ignition lock. If you turn the key to position 3

overall evaluation is shown.

and then press a to confirm Start timing is

continued.

Lap statistics

Resetting the current lap

X Stop the RACETIMER.

X Press = or ; to select Reset Lap .

X Press a to reset the lap time to "0".

Deleting all laps

: Lap

; Lap time

= Average lap speed

? Lap length

A Top speed during lap

If you switch off the engine, the RACETIMER is

reset to "0" after 30 seconds. All laps are

deleted.

Display messages

258

This function is only available if you have stored

at least two laps and have stopped the RACE-

TIMER.

X Press the = or ; button on the steering

wheel to select the AMG menu.

On-board computer and displays

X Press the 9 button repeatedly until the lap

evaluation is shown.

Each lap is shown in a separate submenu. The

fastest lap is indicated by flashing symbol :.

X Press the 9 or : button to select a dif-

ferent lap evaluation.

Display messages

Introduction

General notes

Display messages appear in the multifunction display.

Display messages with graphic symbols are simplified in the Owner's Manual and may differ from

the symbols in the multifunction display.

Please respond in accordance with the display messages and follow the additional notes in this

Owner's Manual.

Certain display messages are accompanied by an audible warning tone or a continuous tone.

When you stop and park the vehicle, please observe the notes on:

R HOLD function ( Y page 193)

R Parking ( Y page 166)

Hiding display messages

X Press the a or % button on the steering wheel.

The multifunction display fades the display message out.

High-priority display messages are shown by the multifunction display in red. Some high-priority

display messages cannot be hidden.

The multifunction display shows these messages continuously until the causes for the messages

have been remedied.

Message memory

The on-board computer saves certain display messages in the message memory. You can call up

the display messages:

X Press = or ; on the steering wheel to select the Serv. menu.

If there are display messages, the multifunction display shows 2 messages , for example.

X Press the 9 or : button to select the entry, e.g. 2 messages .

X Press a to confirm.

X Press the 9 or : button to scroll through the display messages.

When the ignition is switched off, all display messages are deleted apart from some high-priority

display messages. Once the causes of the high-priority display messages have been rectified, these

display messages are deleted as well.

On-board computer and displays -> Menus and submenus for Your Mercedes GLE SUV First Generation (2016-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals