Get Starting & Driving Guide for Mg Zs SUV First Generation (2017-2024)

Starting & Driving

146 Keys

202 Stability Control System (SCS) and

Traction Control System (TCS)

151 Child Proof Locks

204 Cruise Control System

152 Alarm System

207 Active Speed Limit (ASL) System

159 Starting and Stopping Engine

167 Economical and Environmental Driving

*

210 Parking Aid System

4

214 Rear Driver Assistance System ^*

170 Catalytic Converter and Particulate

Filter

220 Tyre Pressure Monitoring System

(TPMS)

172 Fuel System

174 Automatic Transmission ^*

222 Load Carrying

*

181 Manual Transmission

184 Brake System

197 Automated Stop/Start — Intelligent

Fuel Saving System

STARTING & DRIVING

Keys

The keys supplied to you have been programmed for

the security system on your vehicle. Any key that is not

programmed to your vehicle can not start the engine.

Overview

The key only works within a certain range. Its operating

range is sometimes inﬂuenced by the key battery condition,

physical and geographical factors. For safety consideration,

after you lock your vehicle by the key, please recheck if the

vehicle is locked.

Keep the spare key in a safe place - not in the

vehicle!

It is recommended that spare keys are not

，

kept on the same key ring since this may

cause interference and prevent correct key

recognition and therefore prevent the engine

from starting.

The key contains delicate electronic

components and must be protected from

impact and water damage, high temperature

and humidity, direct sunlight and the effects

of solvents, waxes and abrasive cleaners.

1

2

3

Lock button

Different key kits are provided according to vehicle

conﬁgurations. One kit includes two smart keys; and the

other kit includes two remote keys. They can open all

locks.

Tailgate release button

Unlock button

146

STARTING & DRIVING

4

5

Smart key

Replacing the Battery

Remote key

Please use the picture guide to replace the key battery if

any of the following conditions occur:

If your key is lost/stolen or broken, a replacement can be

obtained from an MG Authorised Repairer. The lost/stolen

key can be deactivated. If the lost key is found, an MG

Authorised Repairer can reactivate it.

•

The key locking/unlocking function range is reduced;

The engine immobilisation warning lamp on the

instrument pack ﬂashes (Refer to "Warning Lights and

Indicators" in "Instruments and Controls" section).

Note: Any key made independently outside of MG

Authorised Repairer Network may not start the

engine, and may affect the safety of your car. To

obtain a suitable key replacement, it is recommended

that you can consult MG Authorised Repairer.

*

Smart Key

4

Note: The new key cannot be offered to you

immediately because it requires programming to the

vehicle by the MG Authorised Repairer.

Note: When operating your vehicle with the smart

key, avoid placing it near the devices with strong radio

interference (such as notebook computers and other

electronic products), the normal function of the key

may be affected.

147

STARTING & DRIVING

*

1

2

3

Press the button (A) on the smart key to eject the

decorative trim.

Remote key

Remove the backup mechanical key (B) in the arrowed

direction.

Using a suitable ﬂat bladed tool, insert the tool into

the side of the key (C), carefully prise off the battery

cover and separate the upper and lower casings (D).

4

5

Remove the battery from the slot.

Put the new battery in the slot, and make sure it is in

full contact with the slot.

Note: Make sure that the polarity of battery is

correct ('+' side facing down).

Note: It is recommended to use a CR2032 battery.

6

Reﬁt the cover and press tightly, ensuring the gap

around the cover is even.

7

8

Reﬁt the mechanical key, and close the decorative trim.

Start the engine to resynchronise the key with the

vehicle.

148

STARTING & DRIVING

4

Continue to use the ﬂat-bladed tool inserting it into

the end of the key/battery cover (D), slightly pry the

battery cover until the two bayonets at the end of

battery cover are released.

5

6

Carefully prise off the battery cover (1).

Press the front part of button battery using slight force

(E) to remove the battery (2).

7

Position the new battery, ensuring that correct polarity

is maintained (“+” side facing up), slide it forward (F)

ensuring it is fully inserted into the slot.

4

Note: Make sure the polarity is correct (positive

side upward).

1

2

Unfold the remote key.

Note: It is recommended to use the CR2032

replacement battery.

With a ﬂat-bladed tool, insert it below the arrow mark

at the side of the key (A), and pry up the battery cover

carefully until the lock pins are separated (B).

8

9

Reﬁt the cover and press tightly, check the gap around

the cover is even.

3

Then insert the ﬂat-bladed tool into the illustrated

position (C), and apply pressure in the direction

indicated by the arrow until the tail of the key makes

a gap.

Insert the remote key into ignition switch to

resynchronise it.

149

STARTING & DRIVING

IMPORTANT

•

Use of an incorrect or inappropriate battery may

damage the key. The new replacement’s rated

voltage, sizes and speciﬁcations must be the same

as the old one.

•

Incorrect ﬁtting of the battery may damage the key.

Disposal of the used battery must be strictly in

accordance with relevant environmental protection

acts.

150

STARTING & DRIVING

Child Proof Locks

•

Open the rear door at corresponding side, move

the child proof lock lever to the lock position in the

direction of the arrow to engage the child proof lock;

Move the lever to the unlock position in the reverse

direction of the arrow to disable the child proof lock.

NEVER leave children unsupervised in the

vehicle.

With the child proof lock locked, the rear door at the

corresponding side cannot be opened from inside the car,

but can be opened from outside the car.

4

Steps for enabling or disabling the child proof locks are as

follows:

151

STARTING & DRIVING

Alarm System

be started by using the spare key, please contact an MG

Authorised Repairer.

Your car is ﬁtted with an anti-theft alarm and engine

immobilisation system. To ensure maximum safety and

operation convenience, we strongly recommend you to

carefully read this chapter to fully understand the activation

and deactivation of anti-theft systems.

Engine Immobilisation (Keyless Start) ^*

Press the START/STOP Switch on the instrument

panel, once a valid key is detected in the vehicle, the

immobilisation system will be deactivated automatically.

If the message centre displays ‘Smart Key Not Detected’

or ‘Put Key Into Back-up Position’ or the anti-theft

immobiliser system warning lamp illuminates, please put

the smart key at the bottom of the centre console cup

holder or storage compartment (refer to ‘Alternative

Starting Procedure’ in ‘Starting and Stopping Engine’

section), or try to use the spare key. If the car can still not

be started, please contact an MG Authorised Repairer.

Engine Immobilisation

Engine Immobilisation is designed to safeguard the vehicle

from theft. Engine Immobilisation can only be deactivated

to start the engine by using the matched key.

Engine Immobilisation (Key Start) ^*

When the matched key is inserted into the START/STOP

Switch and the car is started, engine immobilisation is

deactivated automatically. When the key is removed from

the START/STOP Switch, the vehicle will automatically

enable engine immobilisation. When the START/STOP

Switch is in the ON position, if the engine immobiliser

cannot identify the key inserted into the START/STOP

Switch, the engine immobilisation warning lamp in the

instrument pack illuminates. If the engine still can not

152

STARTING & DRIVING

Anti-theft System

tool, insert the tool into the underside of the trim and

carefully remove the driver door lock trim cover, insert

the key into the driver door lock and turn clockwise

to unlock the car.

Locking and Unlocking

When the vehicle is locked, the indicator lamps ﬂash three

times; when it is unlocked, the indicator lamps ﬂash once.

Note: If the START/STOP Switch is not placed in ACC

or ON/RUNNING position within 15 seconds after the

vehicle is unlocked with the mechanical key, the engine

immobilisation alarm will be triggered.

Operation of Door Lock System (Key)

Key Locking

•

Using the remote key to lock: press the lock button on

the key to lock the car after closing the doors, bonnet

and tailgate.

Note: If no panels are opened within 30 seconds after

the vehicle is unlocked by using the remote key, all

doors will automatically re-lock.

4

•

Using the mechanical key to lock: partially operate

the door release handle, using a suitable ﬂat blade

tool, insert the tool into the underside of the trim and

carefully remove the door lock trim cover, insert the

key into the driver door lock and turn counterclockwise

to lock the car.

Operation of Door Lock System (Keyless) ^*

The keyless entry system can lock and unlock the doors

and tailgate as long as you carry the smart key and approach

to the car.

IMPORTANT

Key Unlocking

•

Using the remote key to unlock: press the unlock

button on the key to unlock the car.

The smart key must be within 1.5 metres of the vehicle

for the keyless system to operate correctly.

•

Using the mechanical key to unlock: partially operate

the door release handle, using a suitable ﬂat blade

153

STARTING & DRIVING

Keyless Locking

After switching the START/STOP Switch to OFF position

and exiting the car, press the door handle button once

before moving away from the car to lock all doors and

tailgate (no need to press the lock button on the key).

Note, this will also arm the alarm and immobilise the

vehicle.

Keyless Unlocking

Press the button on the front door handle once to unlock

the car, then pull the door handle to open the door.

Note: When the vehicle is locked, if you are within the

smart key range and operate the door handle button,

but carry out no further action, after 30 seconds

the vehicle will automatically re-lock itself to remain

secure.

IMPORTANT

After the door is locked by using the key, press the

button on the door handle to unlock the car. If the car

cannot be unlocked or locked normally, seek an MG

Authorised Repairer.

154

STARTING & DRIVING

Mislock

in the vehicle is suspended, the lock and unlock function

of the smart key is retained. The engine cannot be

started. To reinstate the immobiliser release function

of the smart key locked in the vehicle the second smart

key should be used to unlock the vehicle. The function

will automatically be reinstated.

If the driver's door is not fully closed when the smart key

lock button is pressed, or the START/STOP Switch has

not been switched OFF, the vehicle horn will sound once,

indicating a mislock. In this case, none of the doors will

lock, the alarm system will not be armed.

•

Both smart keys locked in vehicle - The immobilisation

release function of both smart keys locked in the vehicle

is suspended, the lock and unlock function of the smart

keys is retained. The engine cannot be started. The

reinstatement of key functions can only be carried out

using the approved diagnostic tool. Consult an MG

Authorised Repairer immediately.

If the driver's door is closed, the passenger door, bonnet

and tailgate are not fully closed, the horn sounds once to

indicate mislock when the car undergoes locking operation.

However, the ‘partial arming’ attributes of the security

system will enable as much of the system to be armed as

possible (all fully closed doors, bonnet or tailgate apertures

will be protected, but an open door will not!). The alarm

indicator will ﬂash. As soon as the open aperture is closed,

the system will automatically revert to an armed state

4

Anti-theft Alarm Sounder

If the anti-theft alarm has been triggered, the car horn will

sound continuously. Press the UNLOCK button on the

key, the anti-theft alarm will be deactivated.

Inadvertent Locking of Keys in Vehicle ^*

If the vehicle is locked using the mechanical key blade or

handset whilst a smart key/s remain inside, the following

actions will occur:

•

One smart key locked in the vehicle

-

The

immobilisation release function of the smart key locked

155

STARTING & DRIVING

Interior Lock and Unlock Switch

Note: If the anti-theft alarm system is switched on,

pressing the lock/unlock button will not lock/unlock

the doors but will trigger the alarm system.

If the doors, bonnet and tailgate are closed, press the

interior lock switch. The yellow indicator on the interior

lock switch illuminates.

If a mislock is caused by non-driver door, tailgate or bonnet,

press the interior lock switch. The yellow indicator on the

interior lock switch illuminates.

Interior Door Handles

When the anti-theft alarm system is not in operation, use

the interior door handle to open the door:

1

Pull the interior door handle once to unlock the door.

1

2

Lock Switch

2

Pull the interior door handle again to open the door.

Unlock Switch

Speed Lock

When the anti-theft alarm system is not in operation, press

the lock switch (1) to lock all doors; press the unlock

switch (2) to unlock all doors.

All the doors will be locked automatically when the road

speed exceeds 10 mph (15 km/h).

156

STARTING & DRIVING

Automatic Unlock

Tailgate

When the START/STOP Switch is switched to the OFF

position, all the doors will be unlocked automatically.

If the tailgate can not be closed due to

the type of cargo loaded, be sure to close

all windows during driving, select the face

distribution mode of the air condition, and

set the blower to maximum speed, so as to

decrease exhaust fumes entering the vehicle.

Tailgate Open Mode

4

The tailgate can be opened by using the following 2

methods:

•

When the vehicle is unlocked or the matched key

appears within 1m range around the tailgate, directly

open the tailgate by turning over the emblem on the

tailgate (Figure A).

•

When START/STOP Switch in the OFF position, press

the release button on the remote key (Figure B) for

more than 2 seconds to open the tailgate.

157

STARTING & DRIVING

Emergency Tailgate Opening

The emergency tailgate release access is located in the

centre of the tailgate trim.

Fold down the rear seat to gain access, remove the

blanking plug, and rotate the emergency open knob

counterclockwise to open the tailgate from inside.

158

STARTING & DRIVING

Starting and Stopping Engine

The ignition switch is located on the right side of the

steering column. Function of each position is as follows:

*

（

）

Ignition Switch Key Start

Position LOCK/OFF

When the vehicle is in motion, DO NOT

switch off the ignition or remove the key,

otherwise the steering wheel may be locked,

making it impossible to turn the vehicle.

•

The key can be inserted or removed.

After the engine is stopped and the key is removed,

turn the steering wheel to one side to lock the steering

wheel.

Position ACC

When the vehicle is in motion, DO NOT

touch the key to avoid engine ﬂameout!

•

The engine is not started and the key cannot be

removed.

4

•

Some individual electrical equipment and accessories

can be operated, such as power windows.

Position ON/RUNNING

•

All electrical equipment is operational.

After the vehicle is started, the engine runs.

Position START

•

Engine will run after starting.

Release the key immediately after the engine is

started, the ignition switch will return to position

ON/RUNNING automatically.

159

STARTING & DRIVING

•

When the engine is starting, some electrical equipment

will be isolated during cranking.

START/STOP Switch (Keyless Start)^*

Note: The key can only be turned from ACC position

to LOCK/OFF position when the shift lever is in P

（

）

parking position.

Note: When the ignition switch is in the OFF position,

if the driver side door is opened, an audible warning

sounds to indicate that the key has not been removed.

Note: When the steering wheel is locked and the key

cannot be turned from the OFF position to the ACC

position, please turn the steering wheel slightly whilst

turning the key to unlock the steering wheel.

The keyless START/STOP Switch is located in the fascia to

the left of the steering column, it is a push button style

switch.

Note: To operate the system, the remote key must

be in the car. To remove the gear lever from the

Park position, the START/STOP Switch must be in

ON/RUNNING position, and the brake pedal must be

depressed.

160

STARTING & DRIVING

The operational status displays are as follows:

closing the door, to remind you that the key is still in

the vehicle.

Indicator Off (OFF)

If your car is subject to strong radio signals the keyless

entry and start systems may suffer from interference and

not function correctly. Please see the ‘Alternative Starting

Procedure’.

•

The engine is shut off in this position.

Yellow Light (ACC)

•

Some electrical equipment can be operated, such as

power windows.

Pressing the START/STOP Switch without the footbrake

being applied whilst the engine is OFF will place the

system in the ACC state, this will illuminate the yellow

indicator in the switch button.

4

Green Light (ON/RUNNING)

•

All electrical equipment is operational.

Drive and start the vehicle.

Whilst in the ACC state, pressing the START/STOP

Switch without the footbrake being applied will place

the system in the ON state, the green indicator will

illuminate.

Note: After turning the START/STOP Switch to the

OFF position and opening the door, if the key is still

left in the vehicle, the audible warning will sound when

161

STARTING & DRIVING

*

（

）

Starting the Engine Key Start

Note: When the shift lever is in any other position,

the engine cannot be started.

Never start or leave the engine running in

an unventilated building. Exhaust gases are

poisonous and contain carbon monoxide,

which can cause unconsciousness and may

even be fatal.

4

5

For manual transmission vehicle, ensure neutral is

selected and the clutch pedal is fully pressed;

Insert the key, rotate it to position START and release

the key immediately after the engine is started.

Note: After the engine starts, if the key is not released

immediately, the starter will continue to work, which

will not only discharge the battery, but also damage

the starter and starter motor, catalytic converter and

particulate ﬁlter.

Catalytic converters and particulate ﬁlters

can be damaged if the wrong fuel is used, or

if an engine misﬁre occurs. Before starting

the engine, please read carefully the contents

in the "Catalytic converter and Particulate

Filter" section.

Operation of Starting the Engine

1

2

3

Switch off all unnecessary electrical equipment

(including the air conditioning);

Apply the parking brake (refer to "Brake System" of

this section);

For auto transmission vehicles, ensure the shift lever

is in P or N position;

162

STARTING & DRIVING

*

（

）

（

Starting the Engine Keyless Start

Alternative

Starting

Procedure

Auto

）

Transmission

Starting the Engine:

1

2

3

4

5

Switch off all unnecessary electrical equipment

(including the air conditioning);

Apply the parking brake (refer to "Brake System" of

this section);

For auto transmission vehicles, Ensure P or N is

selected and press the brake pedal .

4

For manual transmission vehicles, ensure neutral is

selected and the clutch pedal is fully pressed.

Press the START/STOP Switch (do not hold the button

in, release immediately).

If the car is located in an area where there are strong

radio signals causing interference or the smart key battery

condition is low, please use the following steps to attempt

to start the car:

1

For vehicles with cup holder, remove the cup holder .

163

STARTING & DRIVING

（

2

Place the smart key centrally in the centre console cup

holder cubby box with the buttons facing upward - as

shown in the illustration.

Alternative Starting Procedure

Manual

）

Transmission

3

Ensure P or N is selected, press the brake pedal and

then press START/STOP Switch to start the vehicle.

If the immobiliser cannot be released after the car has left

the area of strong radio interference or had the smart

key battery replaced please consult an MG Authorised

Repairer.

If the car is located in an area where there are strong

radio signals causing interference or the smart key battery

condition is low, please use the following steps to attempt

to start the car:

164

STARTING & DRIVING

1

2

Place the smart key centrally in the centre console cup

holder cubby box with the buttons facing upward - as

shown in the illustration.

IMPORTANT

•

If the vehicle will not enter a ON/RUNNING state,

please check for any warning indicators or messages

displayed in the instrument pack message centre. In

extremely low temperatures please allow 5 minutes

between starting attempts, if after 3 attempts the

vehicle will not start please consult an MG Authorised

Repairer or breakdown service.

Press the clutch pedal and press START/STOP Switch

to start the vehicle.

If the immobiliser cannot be released after the car has left

the area of strong radio interference or had the smart

key battery replaced please consult an MG Authorised

Repairer.

DO NOT leave the ignition switch in the ACC,

ON/RUNNING or START positions for any length of

time when the engine is not running, otherwise it may

lead to battery discharge due to the use of electrical

equipments.

4

Precautions for Starting the Engine

Idle speed will decrease after engine warm-up. Do not

increase engine speed immediately after engine starts.

Progressively operate the engine and transmission so that

oil can preheat and lubricate all operating components.

•

The vehicle is ﬁtted with engine immobilisation system.

Any independently made key cannot start the engine.

Your car is controlled by electronic control systems.

When starting the engine, please make sure there are

no electronic devices that can create electromagnetic

interference near the vehicle. This may cause issues

with the electronic control systems on the vehicle.

DO NOT press the accelerator pedal while starting and

DO NOT operate the starter for more than 15 seconds at

a time.

In temperatures of -10°C and below, engine cranking times

will increase. It is essential that all unnecessary electrical

equipment is switched off while cranking.

165

STARTING & DRIVING

Stopping the Engine

Note: After strenuous towing or driving at high

speed (particularly in hot weather), it is suggested

to allow the engine to idle for a few minutes before

switching off, which enables the cooling system to

work continuously to lower the engine temperature.

Stop the engine as follows:

1

After bringing the car to a stop, continue to apply the

footbrake until the parking brake is applied;

2

3

Apply parking brake;

For vehicles with automatic transmission, ensure that

the shift lever is in P position.

4

5

For vehicles with manual transmission, ensure that the

shift lever is in neutral position.

For vehicles with key start ， turn the key from

ON/RUNNING position to LOCK/OFF position, the

engine will be shut down and the key can be removed.

6

For vehicles with keyless start，press START/STOP

Switch to shut down the engine.

，

Note: For vehicles with keyless start when the

engine needs to be stopped in emergency,please press

START/STOP Switch and hold for more than 4 seconds

to stop the engine.

166

STARTING & DRIVING

Economical and Environmental Driving

Running-in

Economic Driving and Maintenance

The following are some suggestions on saving fuel and

extending the life of the vehicles.

The engine, transmission, brakes and tyres need time to

‘bed-in' and adjust to the demands of everyday motoring.

During the ﬁrst 900 miles, please heed the following advice

so as to enhance the long-term operation performance:

•

Maintain the correct tyre pressures; insufﬁcient air

pressure will accelerate tyre wear and waste fuel.

•

Do not carry unnecessary weight.

Heavy loads

will increase the engine load resulting in higher fuel

consumption.

•

Do not allow the engine to exceed 3000 rpm in any gear

or the vehicle speed to exceed 72 MPH.

Do not operate at full throttle or allow the engine to

labour in any gear.

•

Avoid engine idling for extended periods.

4

Maintain slow and smooth acceleration and avoid harsh

acceleration; change to a higher gear as soon as possible.

Avoid labouring the engine or over running. Choose

appropriate gears according to the road conditions.

Do not drive at a constant speed (either high speed or

low speed).

•

Avoid heavy braking where possible.

Avoid continuous acceleration or deceleration.

stop-go driving style will consume more fuel.

A

After 900 miles, engine speeds can be gradually increased.

Avoid unnecessary stopping and braking, maintain

steady speed and attempt to anticipate trafﬁc lights.

Environment Protection

Your vehicle has been designed with the latest technology

in order to minimize the environmental impact of exhaust

emissions.

Note: Keep an appropriate distance from other

vehicles to avoid emergency braking and reduce

brake pad wear.

167

STARTING & DRIVING

•

Avoid trafﬁc congestion and jam areas as much as

possible.

Note: To extend the life of all components and

reduce operating costs, regular MG Approved

maintenance is needed.

Anticipating obstructions and slowing down well in

advance, avoids the need for unnecessary acceleration

and harsh braking. A smooth driving style not only

reduces fuel consumption, but can reduce the emission

of noxious gases.

•

Do not stop the engine straight after high speed or long

ascents or towing a trailer. Allow the engine to idle for

20 to 100 seconds depending upon driving loads and

conditions. Avoid hard acceleration on a cold engine.

•

Do not ride the brake pedal, this can cause premature

wear, overheating and increased fuel consumption.

Maintain an appropriate speed on the highway. Higher

speeds use more fuel. Appropriate speeds can save fuel.

Maintain the correct wheel alignment. Avoid collision

with the kerb and reduce speed on uneven road

surfaces. Out of speciﬁcation wheel alignment will not

only lead to excessive tyre wear, but also increases the

engine load and fuel consumption.

•

Avoid driving on mud or beaches. This will prevent

corrosion of the vehicle underside.

Maintain the vehicle in accordance with MG

recommendations. Dirty air ﬁlters, oil etc., will reduce

the engine's performance and raise fuel consumption.

168

STARTING & DRIVING

Driving in Special Environment

Driving in Rain or Snow

Emergency braking, accelerating and steering

on slippery roads will reduce the vehicle's

handling performance and grip.

•

When raining the windows may fog, reducing visibility

(Use the Air-conditioning demist function).

Grip will be reduced when it rains, so please reduce

speed drive carefully.

4

•

Reduce speed when it rains.

Avoid aquaplaning (the effect of a ﬁlm of water between

the tyres and the road) affecting steering and braking

performance.

Driving through Water

Avoid driving through ﬂoods after heavy rain, this may lead

to serious damage to the vehicle.

169

STARTING & DRIVING

Catalytic Converter and Particulate

Filter

The exhaust system incorporates a catalytic converter

and particulate ﬁlter (model dependant), these process

possible harmful exhaust emissions from the engine into

more environmentally friendly gases. Exhaust system

layouts differ between engine derivatives. The 1.5L exhaust

features (A). The 1.0T exhaust features (B).

The temperatures of exhaust systems that

contain particulate ﬁlters and catalytic

converters can be extremely high, DO NOT

park on ground where combustible materials

such as dry grass or leaves could come into

contact with the exhaust system - in dry

weather a ﬁre could result.

Catalytic converters and particulate ﬁlters are easily

damaged through improper use, especially if the wrong

fuel or oil to the incorrect speciﬁcation is used.

Fuel

•

Use only fuel recommended for your car.

Never allow the car to run out of fuel – this could

cause serious damage to the catalytic converter and

particulate ﬁlter.

Engine Oils

It is recommended that only oils that meet the

•

manufacturers speciﬁcation are used. Use of oils that

do not meet the manufacturers speciﬁcations can

damage the particulate ﬁlter, for example low SAPS oils

can affect particulate ﬁlter ash capacity.

170

STARTING & DRIVING

Starting

•

If a misﬁre is suspected, or the car lacks power while

driving, provided the engine has reached its normal

operating temperature, it may be driven SLOWLY (at

risk of catalyst and particulate ﬁlter damage) to an MG

Authorised Repairer.

•

Do not continue to operate the starter after a few failed

attempts; seek an MG Authorised Repairer.

Do not operate the starter if an engine misﬁre is

suspected and do not attempt to clear a misﬁre by

pressing the accelerator pedal.

•

Do not drive on terrain likely to subject the underside

of the car to heavy impacts.

•

Do not attempt to push or tow start the car.

Note: Any engine misﬁre, loss of engine performance

or engine run-on, could seriously damage the catalytic

converter and particulate ﬁlter. Regular maintenance

must be carried out in accordance with the schedule

speciﬁed in the ‘Service Portfolio’. Any modiﬁcations

to engine without being authorised is prohibited.

Regeneration

•

On occasion the particulate ﬁlter may require

regeneration. Your vehicle will automatically carry

out this procedure when certain conditions are met.

During this process you may experience slight power

loss and uneven engine running.

4

Driving

Please pay attention to the following conditions:

•

Do not overload or excessively ‘rev’ of engine.

Do not stop the engine when the car is in motion with

a gear selected.

•

Seek an MG Authorised Repairer if you think your car’s

oil consumption is abnormal.

171

STARTING & DRIVING

Fuel System

Safety Precautions in a Fuel Filling Station

Vehicle fuel gases are highly ﬂammable

and, in conﬁned spaces, are also extremely

explosive.

Fuel Requirements

Use only the recommended fuel which

meets national standard! Serious damage

to the catalytic converter, a reduction in

engine power/torque and increase in fuel

consumption will occur if the wrong fuel is

used.

Always take care when refueling:

•

Switch off the engine.

Do not smoke or use a naked ﬂame.

Do not use a mobile phone.

Avoid spilling fuel.

Please use the fuel which is recommended and certiﬁed

by the manufacturer. See ‘Major Parameters of Engine’ in

‘Technical Data’.

Do not overﬁll the tank.

If a lower grade of fuel is used, an engine knocking noise

may occur, please use the recommended or above grade

fuel as soon as possible. If the engine knocking noise is still

noticeable after using the recommended or above grade

fuel, please contact MG Authorised Repairer immediately.

172

STARTING & DRIVING

Fuel Filler

Fuel Filler Cap

Unscrew the ﬁller cap anti-clockwise and allow any

pressure inside the tank to escape, before removing the

cap.

After refueling, tighten the ﬁller cap clockwise until you

hear one "click" sound.

Refueling

4

Do not fully ﬁll the tank if the vehicle is to be parked in

direct sunlight, or high ambient temperature - expansion of

the fuel could cause spillage. The fuel ﬁller tube is designed

to accept a narrow, long ﬁller nozzle. There is a cover

at the ﬁller neck, by inserting the ﬁller nozzle thoroughly

before fuel ﬁlling, the cover can be fully opened.

Fuel Filler Flap

Start the engine after fuel ﬁlling. After refueling, if

the engine runs unevenly, switch off and seek an MG

Authorised Repairer before attempting to restart the

engine.

The fuel ﬁller ﬂap is located on the rear right-hand wing.

Pull the fuel ﬁller ﬂap release handle under the driver side

instrument pack to open the ﬂap.

173

STARTING & DRIVING

Automatic Transmission ^*

Gear Shift

Instructions

The following information is very important, please read

carefully before use.

•

Before starting the engine, place the gear lever in P or

N position, ensure the foot brake is pressed and the

parking brake is applied.

After the engine has started, ensure the foot brake and

parking brake are applied, shift the lever to the required

gear.

Release the parking brake and hold the foot brake

until you are ready to manoeuvre the vehicle. Once

the foot brake is released, on ﬂat road, the vehicle

will automatically start off at a slow speed without

application of the accelerator.

The automatic transmission is a 6 speed transmission.

Note: The highlighted letters or numbers in the

information centre indicate the selected gear or mode.

•

Do not move the gear shift lever into P or R from

D whilst driving, this will cause severe transmission

damage or cause an accident.

A sprung loaded lock button, located in the gear lever,

is used to prevent mistakingly selecting P (Park) or R

(Reverse) whilst the gear selector is in other positions.

To remove the gear lever from the Park position, the

vehicle must have battery power and the START/STOP

Switch must be in ON/RUNNING position.

174

STARTING & DRIVING

Shift Lever Operation

Unless necessary, it is not recommended to

Free gear shift.

Press and hold the lock button to shift the

gear.

press lock button during gear shifting.

Press and hold the lock button and apply the

brake pedal to shift gear.

Shift Lever Position

The shift lever must be placed in P position

when parked.

4

DO NOT move the gear shift lever into P or

R from D whilst driving, this will cause severe

transmission damage or cause an accident.

•

P Park

When the shift lever is in this position, the transmission

will be mechanically locked. Use this gear only when the

vehicle is stationary and the parking brake is applied.

During the gear shift, operate the shift lever according to

the instructions indicated by the following arrows:

175

STARTING & DRIVING

Note: When the vehicle is parking on a hill, press

the brake pedal and apply the parking brake ﬁrst

and then select P gear.

•

- Downshift

Whilst in Manual mode, downshift the transmission to

the next available low gear.

•

R Reverse

Gearshift Speed

Select this gear only when the vehicle is stationary and

the engine is running at idle speed.

N Neutral

Selecting D will allow the transmission controller to

carry out gearshifts taking in consideration of a number

of factors including engine speed, vehicle speed and

accelerator position. Light accelerator pedal application

will result in a gear-change at low speeds, larger pedal

applications will result in gear-changes at higher speeds.

Select this gear when the vehicle is stationary and the

engine is running at idle speed for a short time (for

example, waiting for trafﬁc lights).

•

D Drive

Kick-down

This is used for normal driving and will allow automatic

selection of 6 gears depending on vehicle speed and

accelerator position.

The drive wheels may skid when kick-down is

activated on road surfaces with low adhesion,

this may lead to the vehicle sliding out of

control.

•

S Sport Mode

Select this mode when a more sporty acceleration

performance is required.

With D gear selected, pressing the accelerator pedal all

the way down in one motion (also known as Kick-down)

will provide better acceleration performance during

overtaking. Under certain conditions, it will allow the

+ Upshift

Whilst in Manual mode, upshift the transmission to the

next available high gear.

176

STARTING & DRIVING

transmission to shift to a lower gear immediately, and

provide fast acceleration. Once the accelerator pedal is

released, it will resume to a suitable normal high gear

(based on the vehicle speed and the position of the

accelerator pedal).

Driving on the Hill

In cases where a short stop on a hill is

required, such as a trafﬁc jam, DO NOT

momentarily apply the accelerator to

prevent “roll back”.

This could cause

the transmission to overheat and result in

damage.

Hill Start

4

In cases of a hill start, where the vehicle has been stationary

for some time, the foot brake has been released and

the electronic parking brake applied, the starting assist

function of the electronic parking brake (EPB) can be used

to prevent the vehicle from rolling backwards. With the

seat belt safely fastened, press the foot brake, apply the

electronic parking brake system, and select the desired

gear (D/R/S), then release the foot brake; press the

accelerator pedal to engage vehicle drive, the electronic

parking brake system will automatically be deactivated.

177

STARTING & DRIVING

Models ﬁtted with Hill Hold Control can use this function

to assist hill starts. For details on hill hold control system,

please refer to "Foot Brake" of "Brake System" section.

Control Mode

Economy Mode

Selecting D automatically places the vehicle in the Economy

Mode. The information centre display will show "D".

Economy Mode provides optimum fuel consumption and

emissions.

Note: The assistance of these functions cannot defy

the laws of physics. DO NOT drive the vehicle beyond

its physical limitations, loss of control will still occur.

Downhill Driving

Sport Mode

Repeated application of the footbrake may

result in the brakes becoming overheated.

This will cause

a

reduction in braking

performance and may even result in brake

failure.

If driving down a hill for long distances, it is advised to

move the gear shift lever to the right and select the Manual

mode. This allows manual gear selection. Use a lower gear

selection to aid the slowing of the vehicle and thus avoiding

over-use of the brakes. If a threshold is reached, the vehicle

will automatically shift up, in these cases use of the brakes

to slow the vehicle is necessary, at the same time re-select

the lower gear.

178

STARTING & DRIVING

Once D is selected, move the shift lever to the right to

select S and enable the Sport Mode (the gear displayed in

information centre changes to "S"). Under Sport Mode,

the transmission upshifts later, so as to make full use of the

power reserves of the engine .

When better acceleration is required, please select the

Sport Mode, but please note that the fuel consumption will

be increased when driving in Sport Mode.

To exit Sport Mode, move the shift lever to the left back

into D position.

4

Cruise Control Mode

With the cruise control function enabled, the transmission

will switch to the relevant gear for the vehicle speed

automatically, thereby avoiding frequent gear shifts when

the system needs to maintain a constant speed.

Move the shift lever toward “+” direction to upshift to next

available high gear, move toward “-” direction to downshift

to next available low gear.

With Manual Mode selected, if the driver makes an

unreasonable gear selection, requests an upshift during

low engine speeds, or requests a downshift during high

engine speeds, the transmission will not respond and will

remain in the current gear. If the vehicle is driven and

the engine speed falls below a preset threshold in certain

Manual Mode

With Sport Mode selected, move the shift lever toward "+"

or "-", this will enable Manual Mode. The gear displayed

in the information centre will indicate current gear with a

single number (1～6).

179

STARTING & DRIVING

gears, the transmission will automatically shift down to

the next gear to avoid engine stalling; when the vehicle

accelerates, if the engine speed exceeds a preset limit, the

transmission will automatically shift up to the next gear to

protect the engine.

Some “failure modes” will cause the transmission to enter

“Limp Mode”, during this time only certain gear positions

can be selected and/or work, for example, R gear may

not be selectable. If a serious functional failure occurs the

vehicle cannot be driven, please consult an MG Authorised

Repairer immediately.

With Manual mode selected, the information centre will

provide gear shift indications, the UP or DOWN arrow

is displayed at the right side of the gear position number,

indicating to the driver to upshift or downshift when the

conditions permit.

Note: When the vehicle is in ‘Limp Mode’, manual

gear selection functions are disabled and therefore not

available.

Note: The gear shift operation should be carried

out on the premise of ensuring your own safety and

observing the trafﬁc regulations.

To return to Sport Mode or any other modes, shift the

lever across to the left and select D.

Automatic Transmission Failure

If the automatic transmission develops

a

problem,

the engine emission malfunction indicator lamp in the

instrument pack will illuminate or the message centre will

display “EP”.

180

STARTING & DRIVING

*

Manual Transmission

Precautions while driving:

1

When selecting R gear, you must ensure that the

vehicle is completely stationary, wait for a moment

and then fully depress the clutch pedal to complete

the gear shift.

5-speed Manual Transmission ^*

Shift lever

Please wait for 2 ～ 3 seconds before shifting to R gear,

otherwise the damage to the reverse gear may occur.

Please wait for 1 ～ 3 seconds before shifting to

forward gear, otherwise the excessive wear to the

synchronizer may occur.

4

2

Do not rest your hand on the shift lever while driving

- pressure from your hand may cause premature wear

to the gear shift mechanism.

3

4

Do not rest your foot on the clutch pedal when driving

- excessive wear to the clutch may occur.

Do not hold the car stationary on a hill by slipping the

clutch. This will wear out the clutch.

The manual transmission is a 5-speed transmission with

6 gears, which are: 1st, 2nd, 3rd, 4th, 5th, R (Reverse)

respectively.

181

STARTING & DRIVING

Gear Shift Indications

6-speed Manual Transmission ^*

Shift lever

When the vehicle is in motion and the clutch pedal fully

released, the information centre will display the currently

selected gear (1-5). An Up/Down arrow is displayed to the

right of the number indicating to the driver to either upshift

or downshift when driving conditions permit.

Note: The gear shift operation should be carried

out on the premise of ensuring your own safety and

observing the trafﬁc regulations.

The manual transmission is a 6-speed transmission with 7

gears, which are: 1st, 2nd, 3rd, 4th, 5th, 6th, R (Reverse)

respectively.

182

STARTING & DRIVING

Precautions while driving:

2

Do not rest your hand on the shift lever while driving

- pressure from your hand may cause premature wear

to the gear shift mechanism.

1

When selecting Reverse gear, you must ensure that

the vehicle is completely in stationery, wait for a

moment and then fully press the clutch pedal, from

the N position, press the lever down and push it

leftward, then push it forward into the R position,

slowly release the clutch pedal to complete the gear

shift.

3

4

Do not rest your foot on the clutch pedal when driving

- excessive wear to the clutch may occur.

Do not hold the car stationary on a hill by slipping the

clutch. This will wear out the clutch.

Gear Shift Indications

4

When the vehicle is in motion and the clutch pedal fully

released, the information centre will display the currently

selected gear (1-6). An Up/Down arrow is displayed to the

right of the number indicating to the driver to either upshift

or downshift when driving conditions permit.

Note: The gear shift operation should be carried

out on the premise of ensuring your own safety and

observing the trafﬁc regulations.

Please wait for 2 ～ 3 seconds before shifting to R gear,

otherwise the damage to the reverse gear may occur.

Please wait for 1 ～ 3 seconds before shifting to

forward gear, otherwise the excessive wear to the

synchronizer may occur.

183

STARTING & DRIVING

Brake System

the car to a halt as quickly as trafﬁc conditions safely

allow, and do not pump the brake pedal as the braking

system will lose any remaining servo assistance.

Foot Brake

•

Once the engine has stopped it will lose any remaining

servo assistance, use suitable force to apply the brake

pedal to stop the car safely in the current trafﬁc

conditions. Contact an MG Authorised Repairer.

Efﬁciency of the brake servo booster can be affected

by numerous conditions, such as engine speed loss.

These conditions could result in extra force required

to operate the brake pedal to stop the car.

For added safety, the hydraulic braking system operates

through dual circuits. If one circuit should fail, the other

will continue to function, but greater pedal pressure will

be needed, and increased brake pedal travel, and longer

stopping distances will be experienced. In the event of a

brake failure where only one circuit is operational, the car

should be brought to a halt as soon as trafﬁc conditions

safely allow. DO NOT continue driving - seek an MG

Authorised Repairer.

Wet Conditions

Servo Assistance

Driving through water or heavy rain may adversely affect

braking efﬁciency. The SCS (Stability Control System)

includes a Brake Disc Wiping function which is activated

when the windscreen wipers are used. However, always

keep a safe distance from other vehicles and intermittently

apply the brake pedal in conditions where the wipers are

not used.

The braking system is servo assisted, always be aware of

the followings during the operation:

•

The servo assistance functions with the engine running

only. Never allow the car to coast with the engine

turned off.

•

Always take particular care when being towed with four

wheels on the ground and the engine turned off. If the

engine should stop for any reason while driving, bring

184

STARTING & DRIVING

Electronic Brake Force Distribution (EBD)

in an emergency situation the brakes are applied faster than

the limits set within the system, then full ABS application is

applied to bring the car to a stop in the shortest possible

distance.

Your car is equipped with Electronic Brake Force

Distribution, which, in order to maintain braking efﬁciency,

distributes braking forces between front and rear wheels,

under all load conditions.

Hill Hold Control (HHC)

EBD integrates a monitoring system. The monitoring

system is linked to the brake system malfunction indicator

lamp on the instrument pack. Refer to "Warning Lights

and Indicators" in "Instruments and Controls" section.

HHC has limitations when subject to adverse

conditions such as wet or icy surfaces and

steep slopes.

4

HHC is not a substitute for parking brake

application when carrying out a hill start.

DO NOT exit the vehicle with only HHC

applied, it may lead to a serious accident

when HHC releases.

If the indicator lamp illuminates while driving, or remains

illuminated after the START/STOP Switch is switched

ON/RUNNING, it indicates there is a failure with the

braking system, and EBD may be inoperative. In such a

case, stop the car as soon as safety permits and seek an

MG Authorised Repairer immediately. DO NOT drive the

car with the braking system malfunction indicator lamp

illuminated.

The car may roll if 'pull-away' is not achieved

immediately after releasing the brake pedal.

Always ensure the brake pedal is pressed or

electronic parking brake applied until drive is

taken up.

Electronic Brake Assistance (EBA)

Your car is equipped with Electronic Brake Assist, which

reacts to the speed at which the brake pedal is applied. If,

185

STARTING & DRIVING

Firm application of the brake pedal when

stopping is required by HHC to generate

sufﬁcient brake pressure to maintain hold.

Note: HHC is available in both forward and backward

directions when pulling away on uphill slopes.

HHC assists the driver by 'holding' the vehicle during hill

starts.

The following conditions must be fulﬁlled to activate HHC:

•

The driver's door is closed and the driver seat belt is

fastened.

•

The vehicle is stopped on a slope for more than 2

seconds.

•

SCS is active and fault free.

EPB is released and fault free.

Clutch pedal is pressed (MT), or in D/R gear (AT).

START/STOP Switch is switched ON/RUNNING.

Sufﬁcient brake pedal application force has been applied.

If the driver releases the brake pedal on a hill, HHC will

maintain brake pressure for 1 - 2 seconds, after this period

the vehicle may roll backwards.

Note: HHC cannot overcome physical limitations. DO

NOT solely rely on HHC.

186

STARTING & DRIVING

Hill Descent Control (HDC)

The HDC system is an auxiliary function specially designed

for driving on acute downhill gradients. The system

reduces the speed by applying brake force, thus assisting

the driver to drive on acute downhill surfaces with low

speeds.

The HDC system is only an auxiliary

function. It has limitations when subject to

adverse conditions such as wet or icy surfaces

and steep slopes. The HDC system cannot

overcome the laws of physics, always ensure

that the vehicle is driven down steep slopes

at low speeds.

Please DO NOT use this function when driving on the

ordinary roads.

When the HDC is working, the brake system may

generate strong vibrations or noise. It is normal during

the operation of HDC.

Even when the HDC system is switched on,

the driver must always pay close attention

to the driving state of the vehicle, and take

active control when necessary. In certain

cases, HDC may be suspended or switched

off temporarily.

4

Note: During the operation of the Hill Descent

Control (HDC) system, please engage a lower gear

on MT models to prevent the engine stalling; on AT

models, please do not move the shift lever to the "N"

position or the HDC function may be deactivated.

During some driving conditions on downhill

surfaces (e.g.

driving down

a

slope at

high speed or small slope, etc.), HDC is

inoperative, the driver must maintain control

of the vehicle at all times and use brake

applications to ensure safety.

187

STARTING & DRIVING

HDC System On/Off

1

2

Standby: Press the HDC switch (ON) to set the

system into standby mode, the green HDC warning

lamp in the instrument pack will illuminate.

Operation whilst in Standby mode, when the vehicle

is driven down an acute gradient, if the vehicle speed

is low, the HDC system will automatically enter

the operating state. In this case, the HDC warning

lamp in the instrument pack ﬂashes green, this may

be accompanied by the working noise of the brake

system. The HDC system will attempt to control the

vehicle drive down the steep slope smoothly.

3

4

Temporary Deactivation: Press the accelerator or

brake pedal beyond a preset limit whilst in operating

mode and the HDC system will temporarily suspend

operation.

When the START/STOP Switch is switched

ON/RUNNING, HDC system defaults to off. Use the

switch function within the infotainment system to turn

the HDC system on/off.

Off: Press the HDC switch (OFF) to switch the system

OFF, the green HDC warning lamp in the instrument

pack will extinguish.

Note: HDC system can work in both forward and

backward directions.

Normally, HDC system has four states:

188

STARTING & DRIVING

Note: During HDC system operation the braking

system will automatically pressurise and maintain

pressure. Operation of the brake pedal during this

phase may result in a 'kickback' sensation through the

pedal. This is normal for HDC operation.

Anti-lock Brake System (ABS)

ABS cannot overcome the physical

limitations of stopping the car in too short

a distance, cornering at too high a speed, or

the danger of aquaplaning, i.e. where a layer

of water prevents adequate contact between

the tyres and the road surface.

HDC ON/Malfunction Indicator Lamp

Refer to "Warning Lights and Indicators" in "Instruments

and Controls" chapter.

The purpose of the anti-lock braking system (ABS) is to

prevent the wheels from locking while braking, thereby

enabling the driver to retain steering control of the car.

4

The fact that a car is ﬁtted with ABS must never tempt

the driver into taking risks that could affect his/her safety

or that of other road users. In all cases, it remains

the driver's responsibility to drive within normal safety

margins, having due consideration for prevailing weather

and trafﬁc conditions.

Under normal braking conditions, ABS will not be

activated. However, once the braking force exceeds the

available adhesion between the tires and the road surface,

thereby causing the wheels to lock, ABS will automatically

189

STARTING & DRIVING

come into operation. This will be recognisable by a rapid

pulsation felt through the brake pedal.

No matter how hard you brake, you are still able to

continue steering the vehicle as normal.

IMPORTANT

Braking in an Emergency

ABS can not reliably make up for the driver's

mis-operation or lack of experience.

DO NOT pump the brake pedal at any time;

this will interrupt the operation of ABS and

may increase the braking distance.

ABS Malfunction Indicator Lamp

If an emergency situation occurs, the driver should apply

full braking effort even when the road surface is slippery.

ABS will ensure that the wheels do not lock and that the

car is brought to a halt in the shortest possible distance for

the prevailing road surface conditions.

Refer to "Warning Lights and Indicators" in "Instruments

and Controls" section.

Note: The normal (non-ABS) braking system remains

fully operational and is not affected by partial or

full loss of ABS. However, the braking distances may

increase.

Note: On soft surfaces such as powdery snow, sand

or gravel, the braking distance produced by the ABS

system may be greater than that for a non-ABS system,

even improved steering would be experienced. This is

because the natural action of locked wheels on soft

surfaces is to build up a wedge of material in front of

(or to the side of, if steering) the tyre contact patch.

This effect assists the car to stop when braking or to

change direction when steering.

190

STARTING & DRIVING

*

Auto Hold

DO NOT leave the vehicle when the engine

is operating and the auto hold is active.

When auto hold stops the vehicle, for reasons

such as engine shut-down, releasing the

seat belt or pressing the auto hold switch,

the electronic parking brake is applied. It

cannot be guaranteed that the vehicle will

be stabilised in all cases. For example, the

rear wheels are on a slippery road surface,

or the vehicle incline is too great (larger than

20%). Please make sure that the vehicle is

safely stabilised prior to exiting.

Auto hold cannot guarantee the electronic

parking brake operation in all cases where

the power system is shut down. Please ensure

the electronic parking brake is applied and

the vehicle is stabilised prior to exiting the

vehicle.

4

The auto hold function should be switched off

during the use of automatic car washes, the

electronic parking brake may suddenly apply

and cause vehicle damage.

DO NOT take any extra risks when driving

due to the fact the vehicle is ﬁtted with

additional convenience functions. The driver

should pay full attention and observe the

surroundings even if the vehicle is equipped

with auto hold system.

If the vehicle is required to stop frequently for a length

of time (such as trafﬁc lights, trafﬁc queues or stop/start),

and the engine is running, the auto hold system assists in

stabilising the vehicle, enabling you to remove your foot

from the brake pedal when the vehicle is stationary and

the Auto Hold active.

The auto hold function cannot guarantee the

stability of the vehicle when starting off or

braking on hills especially on slippery or icy

surfaces.

Auto hold has 3 main states:

1

Off: Function in Off state.

191

STARTING & DRIVING

2

Standby: Function in Standby state. The function is

active but the vehicle has not stopped. Once the

vehicle has stopped, and all other conditions are met,

the system will automatically select Park.

With the driver's seat belt fastened, the door closed and

the engine running, press the auto hold switch to switch

the auto hold function from Off to Standby state.

With the brake pedal ﬁrmly pressed and the vehicle

completely stopped, the auto hold function will switch

from the Standby state to the Parking state.

3

Parking: Function in Parked state. In this state the

green

indicator on the instrument pack illuminates.

When the auto hold is in the Parking state, engaging

forward or reverse gear and pressing the accelerator will

automatically release the auto hold function.

In some circumstances such as releasing the seat belt,

switching off the engine or remaining static for a length

of time it will result in the vehicle exiting the auto hold

Parking state. At this time the electronic parking brake

will remain applied and will require the driver to release

it using the switch.

Note: With the brake pedal pressed, operating the

switch to turn the auto hold off, the system will NOT

apply the parking brake.

Note: It is recommended to turn off the auto hold

function when reversing into the garage.

192

STARTING & DRIVING

Emergency Braking Hazard Warning Lights

Control (HAZ)

Active Rollover Protection (ARP)

The ARP system cannot overcome the laws of

physics. It is a driver aid to assist the stability

of the vehicle and under extreme conditions.

It is not a guarantee that the car will not roll

over.

If the vehicle is travelling in excess of 31 mph (50 km/h)

and the driver makes an emergency braking manoeuvre,

the hazard lights will be operated to indicate this to other

drivers.

Note: If the hazard warning lights are being operated

manually, this suspends the HAZ function.

In cases where the vehicle has a high centre of mass, rapid

or excessive dual direction lane changing may create a

roll condition. ARP may use the braking system to apply

certain brakes to try and correct the condition and assist

in preventing rollover.

4

When the emergency braking manoeuvre is exited (no

severe deceleration detected) then the function will be

switched off after a few seconds.

Note:

During ARP application the steering

Note: As the car speed drops to below 6 mph (10 km/h)

and the system no longer ﬂashes the brake lamps, the

hazard warning lamps will illuminate automatically.

Short press the hazard warning lamp switch or increase

your speed to above 12 mph (20 km/h) for 5 s to switch

off the hazard warning lamps.

characteristics of the vehicle may be noticeably

different from normal.

193

STARTING & DRIVING

*

Parking Brake

The parking brake operates on the rear wheels only. To

apply the parking brake, pull the lever up. Always apply the

parking brake fully whenever you park the car.

DO NOT drive with the parking brake

applied, or apply the parking brake while

the car is in motion. This could result in loss

of control, prevent the ABS from functioning

correctly, and may even cause damage to

the rear brakes.

To release, pull the lever up slightly, press the button

(arrowed in illustration) and fully lower the lever. When

parking on a steep slope, do not rely on the parking brake

alone to hold the car.

194

STARTING & DRIVING

Electronic Parking Brake (EPB) ^*

Applying the EPB

While the vehicle is stationary, the EPB can be applied.

Ensure the EPB is applied every time the vehicle is left or

parked.

In the event of EPB malfunction where EPB

release is not possible, please consult an MG

Authorised Repairer in order to carry out an

emergency manual release of the parking

brake.

•

Press the brake pedal, pull the EPB switch upward until

the indicator in the EPB switch illuminates.

If the indicator in the EPB switch and the indicator in

the instrument pack illuminates,

the EPB is applied.

P

If the EPB malfunction indicator lamp

in the

4

instrument pack remains on, it indicates that a fault

has been detected. Please contact an MG Authorised

Repairer immediately.

Note: An audible motor noise may be heard when

applying or releasing the EPB.

IMPORTANT

•

In the event of a ﬂat battery or power failure, it is not

possible to apply or release the EPB. In such a case,

'jump leads' shall be used for emergency engine start,

please refer to "Emergency Starting" in "Emergency

Information" chapter.

195

STARTING & DRIVING

Releasing the EPB

When the car is in motion, in case of any emergency, such

as the car can not be stopped by the brake pedal, it can be

decelerated by pulling up and holding EPB switch.

•

Switch on the ignition, press the brake pedal, and press

the EPB switch.

•

Pull the EPB switch upward and hold to realise the

emergency braking. Continuous acoustic alarm will

sound simultaneously during emergency brake.

To cancel the emergency braking process, release the

EPB switch.

•

If the indicator in the EPB switch and the indicator in

the instrument pack

released.

are extinguished, the EPB is

•

Start Assist

The EPB can predict the driver's intention and

automatically release the EPB.

If the driver's seat belt is fastened, the engine is started

up, D or R gear is selected and the accelerator pedal is

depressed for start off, the EPB will automatically release.

Emergency Braking Function

Inappropriate use of the EPB can lead to

accidents and injuries. Do not apply the EPB

for vehicle braking, unless in emergency.

During emergency braking using the EPB, DO

NOT switch off the ignition, this could result

in serious injury.

196

STARTING & DRIVING

Automated Stop/Start — Intelligent

Fuel Saving System

Engine Stop/Start has been incorporated into vehicles in

an effort to reduce emissions. As the name suggests the

system will allow the engine to be switched off when engine

power is not required and then automatically be restarted

when it is.

This system defaults “on” with the START/STOP Switch

in the ON/RUNNING position, the Main Switch Indicator

Lamp is on (2 shown in ﬁg ) and can be turned off by

pressing the Main Switch (1 in the ﬁg). The lamp in the

switch will extinguish.

4

Note: If vehicle is driving through deep water, please

use Main Switch (1 in the ﬁg) to shut down Stop/Start

intelligent fuel saving system.

1

2

Main Switch

Main Switch Indicator Lamp

197

STARTING & DRIVING

Automatic Shutdown of Engine

•

The vehicle speed prior to stopping exceeded 6 mph

(10 km/h).

Although the engine is not running after an

automatic stop, the system is prepared to

auto start therefore the following actions

could be dangerous:

Vehicles with manual transmission: Gearbox must be in

neutral and clutch pedal is released.

On automatic derivatives if D is selected and the brake

pedal pressed the engine will automatically stop. Shifting

the gear selector to P/N and releasing the brake pedal

will maintain the engine shutdown status.

The driver’s door is closed and seat belt is secured.

The bonnet is closed.

1

Leaving the vehicle while the seat belt is

still buckled, or there is a substitute seat

belt buckle inserted.

•

2

3

Carrying out work or checks in the engine

compartment.

Transmission in Drive with footbrake pressed. (auto

only)

Refuelling the vehicle, the START/STOP

Switch must be switched “OFF” or the

key removed from the switch.

•

No demands on the steering. (auto only)

4

Vehicles with automatic transmission:

Leaving the vehicle while the gear

selector is still in Drive position (R/D/S).

Stop/Start Prohibited

Start Stop will not operate if:

•

Coolant temperature is below a preset limit .

Front defrost is on.

Engine Auto Stop Conditions

Battery power is below a preset limit.

The vacuum in the braking system is below a preset

limit.

Engine Auto Stop Conditions (Under Start Stop Control,

Instrument Pack Indicator Lamp on)

•

Vehicle is stationary, i.e. speed =0 mph or km/h.

198

STARTING & DRIVING

•

Starter motor temperature is above a preset limit.

Reverse gear selected or has been selected prior to

parking.

With the engine stopped in the automatic Stop/Start

condition, the following actions will cause an automatic

restart.

•

Battery power falls below a preset limit.

The vacuum in the braking system falls below a preset

limit.

•

Heating or cooling demand is too great.

Vehicle is standing at excessive angles. (auto only)

Automatic Engine Start

•

The vehicle begins to move.

Main Switch (1 in the ﬁg) is pressed.

With the engine stopped in the automatic Stop/Start

condition, the following driver actions will cause an

automatic restart, at this time the instrument pack

indicator lamp is off.

At this time the instrument pack indicator lamp

extinguish to indicate engine start phase.

will

4

Start Inhibition

•

Models with automatic transmission and in D position:

release the brake pedal, or shift out of Drive position.

Models with manual transmission: Transmission in

Neutral position: press the clutch pedal or accelerator

pedal.

Note:

When

a

vehicle ﬁtted with

a

manual

transmission is under automatic Stop/Start control

and the engine is required to restart, but neutral

position is not selected, the engine will restart when

neutral position is selected.

•

Vehicles with automatic transmission: Release the brake

pedal with the shift lever in D position, or depress

the brake/accelerator pedal with the shift lever in P/N

position, or shift the lever to Drive(R/D/S) position.

If any of the following conditions occur during automatic

engine stop, the engine can only be restarted using the key,

during this time the instrument pack indicator lamp will

extinguish.

•

The driver side seat belt is unbuckled.

199

STARTING & DRIVING

•

The driver side door is open.

Bonnet is open.

Battery

When charging the battery, starting the car

At this time the instrument pack indicator lamp

extinguish to indicate engine start phase.

will

with an external power source or supplying

power from the vehicle, the negative cable

must be connected to a suitable position on

the vehicle body. Failure to do this will result

in inaccurate battery power calculation

which will effect automatic Stop/Start

control.

Stall Assist

This function is available once the Stop/Start intelligent fuel

saving system is enabled without any inhibiting conditions.

If the engine cuts out, or is stalled whilst Stop/Start is

enabled, selection of neutral and pressing the clutch pedal

will automatically restart the engine.

DO NOT disconnect the battery sensor

unless absolutely necessary.

removal

Note: Extremely low battery power may result in the

engine not re-starting automatically, or even using the

key. In this instance, external power is needed to start

the engine or the battery will require re-charging. See

the section ‘Emergency Starting’ in the ‘Emergency

Information’ Chapter.

will result in inaccurate battery power

calculation which will effect automatic

Stop/Start control.

Note: Failure to operate within the following

guidelines will effect battery performance and

automatic Stop/Start control:

1

After power interruptions (battery disconnection)

the automatic Stop/Start function will be

suspended until the vehicle is left in a locked state

200

STARTING & DRIVING

for at least 4 hours whilst the system relearns the

state of the battery.

Starter Inoperative,

Capacity Loss

Serious Battery

In the case of serious battery power loss, automatic

Stop/Start and key start may not be possible. In this case

see the section ‘Emergency Starting’ in the ‘Emergency

Information’ Chapter.

2

3

If the vehicle is run continually for more than 100

hours uninterrupted, the Stop/Start function will

be suspended until the vehicle is left in a locked

state for at least 4 hours whilst the system relearns

the state of the battery.

If the battery requires replacement, ALWAYS use a

genuine part to the manufacturers speciﬁcation.

4

Failure to adhere to this can affect the automatic

Stop/Start system.

Automated Stop/Start Intelligent Fuel

Saving System Failure

In the event of a Stop/Start Intelligent Fuel Saving System

failure, contact an MG Authorised Repairer.

The Stop/Start Intelligent Fuel Saving System can be

effected by faults within other vehicle systems - in the

event of failure contact an MG Authorised Repairer.

201

STARTING & DRIVING

Stability Control System (SCS) and

Traction Control System (TCS)

non-spinning wheel. If both wheels are spinning, the

system will reduce engine speed in order to regulate wheel

rotation until traction is regained.

Stability Control System (SCS)

Switching On/Off

SCS is designed to assist the driver in control of driving

direction. The SCS is automatically activated after the

engine is started.

When SCS detects that the vehicle is not moving in the

intended direction, it will intervene by applying brake force

to selected wheels or through the engine management

system to prevent sliding and assist in bringing the car back

to the right direction.

Traction Control System (TCS)

The purpose of electronic traction control is to aid

traction, thereby helping the driver to maintain control

of the car in situations where one or both of the driving

wheels are spinning (for example, if one wheel is on ice

and the other on tarmac). The traction control system

monitors the driving speed of each wheel individually. If

spin is detected on one wheel, the system automatically

brakes that wheel, transferring torque to the opposite,

With the START/STOP Switch is switched ON/RUNNING,

SCS and TCS will automatically turn on. And you can turn

them off after the engine is started.

202

STARTING & DRIVING

•

Press SCS switch (less than 2 seconds) to turn off TCS.

Press SCS switch (longer than 2 seconds) to turn off

SCS and TCS.

Note: Press the SCS switch (more than 10 seconds),

it will be regarded as misoperation.

To recover the operation of SCS and TCS, press SCS

switch once again.

•

Note: Disabling SCS and TCS will not affect the

operation of ABS. Always disable TCS when driving

with snow chains ﬁtted.

4

Stability Control/Traction Control Warning

Lamps

Refer to "Warning Lights and Indicators" in "Instruments

and Controls" section.

203

STARTING & DRIVING

Cruise Control System

journey where a constant speed can be maintained for a

lengthy period.

Cruise Control System Activation

Cruise control system is operated with a lever located, at

the left side of the steering wheel underneath the lighting

stalk switch.

With the START/STOP Switch in position ON/RUNNING,

if the lever switch is in the 'ASL Standby' position (7

in ﬁgure), then the cruise control is OFF. To set the

cruise control to 'Standby' pull the lever switch to 'Cruise

Standby' (4 in ﬁgure), the yellow indicator lamp

in the

instrument pack will illuminate indicating the system is in

'Cruise Standby' mode.

With the system in 'Standby' when the current vehicle

speed is above 25mph (40km/h), press the 'Cruise Set'

•

Acceleration (1)

Deceleration (2)

Cruise Cancel (3)

Cruise Standby (4)

•

Cruise Resume (5)

Cruise Set (6)

button (6 in ﬁgure). The indicator

in the instrument

ASL Standby (7)

pack will change to green and the cruise control will enter

and activated state. The operating range is 25 - 125 mph

(40 - 200 km/h).

Cruise control enables the driver to maintain a constant

road speed without using the accelerator pedal. This

is particularly useful for motorway cruising, or for any

204

STARTING & DRIVING

The target speed of the cruise system will be set at the

current speed, and the cruise system will take effect. At

this time, the cruise control system will maintain the set

speed without pressing the accelerator pedal.

1 mph(1 km/h), then the vehicle will accelerate/decelerate

to the new target speed.

Pressing the accelerator at any time will override the cruise

control and allow acceleration to undertake manoeuvres

such as overtaking. Releasing the accelerator will return

the vehicle to the set target speed.

Note: The set speed held in the cruise control memory

will be cancelled when either the cruise control lever

is switched to "ASL Standby" position (ﬁgure 7) or the

START/STOP Switch turned off.

Pause/Stand By

Cruise control will be disengaged and set to 'Standby' if:

4

Target Cruise Speed Adjustment

•

Lever switch moved to 'Cruise Cancel' position (3 in

ﬁgure).

When the cruise control is active, the 'target speed' can be

increased or decreased:

•

Brake pedal pressed.

Auto gear lever moved to P, R or N.

Manual gear-change made.

Push the lever switch upwards (1 in ﬁgure), this will

increase the speed.

Clutch pedal pressed.

Push the lever switch downwards (2 in ﬁgure), this will

decrease the speed.

Conditions initiate SCS intervention.

An incline causes excessive decline in speed.

Release the lever switch when the desired speed is reached.

Resume

Push the lever switch upwards or downwards brieﬂy to

increase/decrease the vehicle target speed in increments of

If the cruise control remains on after the disengagement,

moving the lever switch to 'Cruise Resume' (5 in ﬁgure)

205

STARTING & DRIVING

will reinstate the target speed to the setting prior to

disengagement.

•

DO NOT operate the switch for excessively long

periods, or press multiple switches simultaneously,

this may cause the system to fail. If this situation

occurs, when it is safe to do so, cycle the ignition.

Note:

•

Never use the cruise control system in the reverse

gear.

•

DO NOT use the cruise control in unsuitable

conditions, such as on slippery surfaces, excessively

heavy rain or in trafﬁc conditions that DO NOT

suit maintenance of constant speeds.

•

When not in use, ensure the lever switch is in the

'ASL Standby' position (7 in ﬁgure).

When the automatic transmission is in "Sport"

mode, it is not recommended to use the cruise

control system.

•

During the operation of cruise control system, the

actual speed may deviate from the target cruise

speed to some extent due to road conditions (such

as uphill, downhill, etc).

If the actual speed is excessively lower than the

target speed or SCS is activated due to the hill

or road surfaces, the cruise control system may

automatically revert to standby mode.

206

STARTING & DRIVING

Active Speed Limit (ASL) System

The Active Speed Limit (ASL) system is designed to control

the vehicle speed keeping it below a speed set by the driver.

The ASL system shares the same lever switch as the cruise

control system, located to the left of the steering wheel

below the indicator stalk. The switch can be toggled

between both functions, however only one function can

operate at any one time.

Activate

4

The desired target speed of the ASL system is displayed in

the instrument information cluster, refer to "Information

Centre" in the "Instruments and Controls" section. With

the START/STOP Switch in position ON/RUNNING and

the lever switch in "ASL Standby" (7 in ﬁgure), the ASL

function is in standby mode by default, brieﬂy moving the

lever switch up/down (1,2) adjusts the target speed of the

ASL. The range of target speed adjustment is 20 - 130 mph.

1. Speed Limit Increase

2. Speed Limit Decrease

3. Cruise Cancel

5. Cruise Resume

6. Set (Activate)

7. ASL Standby

The target speed limit value will be increased or decreased

by 5 mph every time the lever switch is brieﬂy moved

upwards or downwards.

4. Cruise Standby

207

STARTING & DRIVING

Pressing the "Set" button (6 in ﬁgure) will activate the ASL

system and set the speed limit. The ASL indicator lamp in

the instrument pack will illuminate.

Suspending ASL

When ASL is active, to suspend the feature press the

"Cruise Standby" button (4) and the ASL system will exit

to the standby state returning control to the accelerator

pedal.

When activated if the vehicle speed is greater than the

user inputted target speed the system will immediately

begin to slow the vehicle to the inputted target.

Note: When suspended via the "Cruise Standby"

button (4) the previously inputted target speed will be

retained within the system memory in the case that

the system is reactivated.

Kick Down

With the system active if it is necessary to accelerate the

vehicle e.g. overtaking manoeuvre, the system can be over

ridden by pressing the accelerator pedal passed a kick down

position. The kick down position is approximately at the

overall accelerator pedal travel pressed. Once the kick

down position has been reached the ASL system enters a

standby state and returns the vehicle operation to the user,

accelerating according to the demand from the accelerator

pedal.

Resuming ASL

If the system has been placed in a standby state with a

retained target speed the system can be reactivated to the

previously stored target speed by pressing the "Set" button.

Note: After the ignition is switched OFF, the target

speed previously stored will be erased. In the interest

of economy and safety, it is recommended to select

different target speeds according to different driving

and road conditions.

After a kick down event, once the vehicle speed has

dropped below the target speed originally controlled to,

the ASL system will automatically resume and control the

vehicle to the target speed retained within the system.

208

STARTING & DRIVING

Overshoot of Target Speed and Warning

The system is designed to control the vehicle speed to

within +/- 1.5 mph (2 km/h) of the inputted target speed.

However, the feature does not incorporate vehicle braking

assist, therefore if the ASL system is attempting to control

vehicle speed on a steep downhill incline the inertia of

the vehicle may force the vehicle speed over the intended

target speed.

If at any time the vehicle speed increases 2 mph (3 km/h)

more than the desired target speed the system informs the

user with continuous visual and periodic audible warnings.

Once the desired target speed has been maintained the

warnings are removed.

4

Note: If the target speed has been deliberately

exceeded i.e. Kick Down, only a visual warning is

displayed.

209

STARTING & DRIVING

*

Parking Aid System

Rear Parking Aid

The ultrasonic sensors in the rear bumper monitor the area

behind the vehicle to search for obstacles. If any obstacle

is detected, the system will calculate its distance from the

rear of the vehicle and communicates the message to the

driver by sounding warning chimes.

Ultrasonic Sensor Parking Aid ^*

The purpose of the parking aid is to assist the

driver in reversing! The sensors may not be

able to detect obstacles of certain type, e.g.

narrow posts or small objects no more than

a few inches wide, small objects close to the

ground, objects above the tailgate and some

objects with non-reﬂective surfaces.

Parking Aid in Operation

When the START/STOP Switch is in the ON/RUNNING

position, the rear parking aid is enabled automatically when

reverse is selected, it is switched off as soon as reverse is

disengaged. A short beep is given by the parking aid within

1 second after selecting reverse to indicate that the system

is operating normally.

Keep the sensors free from dirt, ice and snow.

If deposits build up on the surface of the

sensors, their performance may be impaired.

When washing the car, avoid aiming high

pressure water jets directly at the sensors

from close range.

The entertainment system screen will display a silhouette

image of the car showing the object distance values for the

sensor.

Note: If a longer, higher pitched sound is emitted for 3

seconds when reverse is selected this indicates a fault

in the system. In this case seek assistance from your

MG Authorised Repairer.

210

STARTING & DRIVING

With the parking aid enabled, when obstacles are detected,

the system will give sounds in different frequencies (there

might be blind areas).

•

Once the obstruction is within 30cm range of the rear

bumper, the beeps will merge into a continuous warning.

4

•

If there is an obstacle within 1.2m range from the rear

sensors, the system starts to emit a beeping sound. As

the vehicle moves closer to the obstacle, the beeps are

transmitted more rapidly.

211

STARTING & DRIVING

360 Panoramic Imaging System ^*

The purpose of the 360 panoramic imaging

system is to assist the driver during reversing!

The cameras have a limited ﬁeld of view and

cannot detect obstructions outside the ﬁeld

of view.

Although the entertainment display can

provide high-deﬁnition images around the

vehicle, please still pay attention to the

current actual road conditions for your

driving safety.

•

Touch or press the 360° View button to enter into the

display interface of the 360 panoramic imaging system,

you are then able to touch buttons on the display to

check images from different angles of view of the vehicle

to provide a much safer driving environment.

With the 360 panoramic imaging system working, the

display interface will show a 360° panoramic image of the

vehicle to facilitate the observation of the surrounding

environment to make driving safer.

Touch the 2D or 3D button on the display to enter

into the display interface of the 2D or 3D panoramic

imaging system, you are then able to touch different

areas around the vehicle (as displayed on the LH side

of the screen) to check images from different angles of

view to provide a much safer driving environment.

Touch the Setting button in the upper right corner of the

screen to open the 'Settings' interface, here you are able

•

When the reverse gear is selected, the system will

automatically switch to the display interface of a 360°

panoramic image, this will appear in the entertainment

display.

•

212

STARTING & DRIVING

to switch the "when corner lights/indicators* are active

start the 360° view" function ON/OFF. When a forward

gear is selected and the left/right corner light/indicator*

is on, the 360 panoramic image system will display the

corresponding left/right view.

•

Touch the Setting button in the upper right corner of the

screen to open the 'Settings' interface, here you are able

to set the parking aid line to static, dynamic, dynamic +

static, and off state.

4

Note: When the shift lever is placed in forward gear

position, in no case can 360 panoramic imaging system

be enabled as long as the vehicle speed exceeds or

equals to 10mph (15 km/h).

213

STARTING & DRIVING

Rear Driver Assistance System ^*

The rear driver assistance function is only an

aid, it is NOT a substitute for the attention

of the driver. The driver must always remain

in control, observe the surroundings and drive

safely.

System Overview

The effective recognition capabilities of the

rear sensors can be limited by objects such

as roadside buildings, guardrails, changes in

pitch angle of the car due to heavy loading,

road conditions such as bends or bumps or

weather conditions such as snow and ice etc.

Any of the above may trigger a false alarm.

The correct operation of the rear sensors will

be compromised if they are misaligned due to

accident damage. This may cause the system

to automatically shutdown.

To ensure that the radar sensors work

correctly, the rear bumper should be kept

free of snow and ice and must not be covered.

The rear driver assist system may not provide

adequate warning of very fast approaching

vehicles or operate correctly on tight curves

of 500m radius or less.

Use of non recommended materials or

paint on rear bumper repairs may have a

detrimental effect on the operation of the

rear sensors. Please only use recommended

materials.

The rear driver assist system will not operate

correctly whilst towing a trailer or caravan.

The system has limitations and may not be

able to warn of vehicles approaching at high

speeds.

214

STARTING & DRIVING

The rear driver assistance system includes blind spot

detection (BSD), lane change assist (LCA), and rear cross

trafﬁc alert (RCTA) functions.

The rear driver assistance modules are mounted at the

rear of the vehicle on each side, they can assist in detecting

vehicles behind or to the side of your vehicle.

The warning lamps to support this system are located

within the LH and RH door mirror glasses, they will

illuminate or ﬂash to warn of an approaching object or car

to assist you in manoeuvring the car safely.

4

Note: The radar requires calibration on new vehicles

or for vehicles of where

a

rear detecting radar

sensor has been replaced. The rear detection radar

sensors possess an automatic calibration function to

compensate for installation error within a certain

range. When the vehicle is running, the radar will

automatically enter the calibration state. During the

calibration process, the system will provide limited

functions, and the alarm may be inaccurate. Upon

215

STARTING & DRIVING

completion of the calibration, the system will resume

all functions.

System Functions

Note: The detection area, collision time threshold

value and vehicle speed provided in the system

function description are just for your reference.

Switching the System Functions On/Off

The rear driver assist system function and sub system

switches can be accessed via the infotainment screen.

Blind Spot Detection (BSD)

When the vehicle is driving forward, the system will

monitor the motor vehicles located in the blind zones of

the left and right exterior mirrors. When the conditions

for activating the blind spot detection function are met, the

warning lamps in the corresponding mirror will illuminate.

Subsequent operation of the relevant indicator will cause

the warning lamp in the mirror to ﬂash to remind the

driver of an approaching vehicle.

Select: 'Vehicle Settings', 'Driving Assist' and 'Rear Driving

Assist' (you may have to scroll left or right to access this

option). Select ON/OFF to activate/deactivate the system.

A warning message to alert you of your choice will be

displayed in the message centre in the instrument pack.

When the vehicle is restarted, the system will keep the

previously stored switch settings.

216

STARTING & DRIVING

of the vehicle, the monitored areas are 2m ahead , 7m

behind the rear of the vehicle, and 4.7m from the side

of the vehicle.

Note: The warning lamps will not illuminate whilst

you are overtaking another vehicle and your speed is

greater than that of the vehicle you are passing, even

though it is in the blind zone.

4

The conditions for activating the blind spot detection

function include:

1

Rear driver assistance system is in the ON state and

no faults are present in the system.

2

3

4

Blind spot detection (BSD) function is enabled.

The vehicle speed is above 20mph (30km/h).

There are motor vehicles in the blind zone of the

vehicle. The system monitors both the left and right

217

STARTING & DRIVING

Lane Change Assist (LCA)

The conditions for activating the lane change assist function

include:

When the vehicle is driving forward, the system will

monitor the motor vehicles approaching rapidly in the

adjacent lanes. When the indicators are activated, and the

conditions for activating the lane change assist function

are met, the system will ﬂash the warning lamp within the

respective mirror to warn the driver of an approaching

vehicle. This aims to help avoid collisions when changing

lanes.

1

Rear driver assistance system is in the ON state and

no faults are present in the system.

2

3

4

Lane change assist (LCA) function is enabled.

The vehicle speed is above 20mph (30km/h).

The speed of the approaching vehicle is higher than the

speed of your vehicle.

5

6

The approaching vehicle enters the detection area of

the LCA, the monitored areas are 7 - 70m behind your

vehicle and 4.7 m to the side of your vehicle.

The approaching vehicle is likely to have a collision with

your vehicle within 3.5 seconds.

218

STARTING & DRIVING

Rear Cross Trafﬁc Alert (RCTA)

The conditions for activating the rear cross trafﬁc alert

function include:

When the vehicle is reversing, the system will monitor

vehicles approaching from the left and right rear. When

the conditions for activating RCTA function are met, the

warning lamps in the mirrors on the corresponding side

will illuminate, simultaneously a warning triangle icon for

the corresponding side will be displayed in the infotainment

screen to alert the driver to the situation.

1

Rear driver assistance system is in the ON state and

no faults are present in the system.

2

3

4

5

Rear cross trafﬁc alert (RCTA) function is enabled.

The vehicle is in Reverse gear.

The vehicle speed is less than 5mph (9km/h).

The speed of the vehicle being monitored is above

5mph (9km/h).

4

6

The motor vehicle drives across the system detection

areas. The areas monitored to the left and right of the

vehicle are 5m behind the rear of the vehicle, and 25m

from the side.

7

The approaching vehicle is likely to have a collision with

your vehicle within 2.5 seconds.

219

STARTING & DRIVING

Tyre Pressure Monitoring System

(TPMS)

reinﬂate to the correct pressure. Please refer to ‘Tyre

Pressure (Cold)’ in ‘Technical Data’ section.

System Malfunction

TPMS cannot replace routine maintenance

and check of the tyre condition or pressure.

This system is self-monitoring, if a malfunction

is detected, the TPMS warning lamp (yellow) on the

instrument pack will ﬂash for 90 seconds ﬁrst and then

illuminate.

If radio transmission devices such as mobile

telephones or wireless headsets are used in

close proximity to the vehicle it may result

in interference with the TPMS and could

register as a fault.

Note: When a puncture is detected, the system will

require some time to analyse information prior to

illuminating the warning lamp.

Note: TPMS only gives the driver a warning when the

tyre pressure is low, it will not inﬂate the tyre.

Under certain conditions the warning light may illuminate

when a fault is not present, these conditions include:

TPMS uses pressure sensors built into tyre valves to

continuously monitor pressure and transmits signal to ECU

inside the vehicle using RF signals. If it deduces that the

pressure of that tyre has fallen below the predeﬁned limit

of the system, the warning light on the instrument pack will

illuminate (always yellow). For more information, please

refer to ‘Instrument Pack’ in ‘Instruments and Controls’

section. Check your tyres at the earliest opportunity and

•

A non recommended tyre ﬁtted (including spare tyre).

Rough terrain driving for excessive periods.

Bending or mountain type terrain driving for excessive

periods.

•

TPMS will not respond immediately if a tyre 'blows out'.

220

STARTING & DRIVING

TPMS Self-learning

The TPMS system is a 'self learning' system, after resetting

tyre pressures it will be necessary to allow the system to

go through a self learning process. This is done by driving

the car, during this process the system is suspended and the

data displayed may not be correct. If sensors or receiver

module are replaced the system requires programming,

consult an MG Authorised Repairer. If the wheels are

swapped or rotated the system requires reprogramming

to learn the new transmitter positions, consult an MG

Authorised Repairer.

4

221

STARTING & DRIVING

Load Carrying

as to avoid the cargo shift in the event of an accident or

sudden stop.

DO NOT exceed the gross vehicle weight

or the permitted front and rear axle loads.

Failure may result in vehicle damage or

serious injury.

Drive carefully and avoid emergency braking or maneuvers

when large or heavy items are carried.

Driving with the boot lid (or tailgate) open is very

dangerous. If the load being carried requires the boot

lid (or tailgate) to be open, please ensure the cargo and

the boot lid (or tailgate) are suitably secured and every

measure is taken to prevent exhaust fumes entering the

vehicle.

Load Space

Ensure that the rear seat backrests are

securely latched in the upright position when

loads are carried in the load space behind

the seats.

IMPORTANT

Trafﬁc regulations must be observed when loading

cargo, if the cargo extrudes the loadspace, appropriate

warning measures must be taken to warn other road

users.

If the boot lid (or tailgate) can not be closed

due to the type of cargo loaded, be sure to

close all windows during driving, select the

face distribution mode of the air condition,

and set the blower to maximum speed, so

as to decrease exhaust fumes entering the

vehicle.

When luggage carried in the boot, always ensure heavy

items are placed as low and as far forward as possible, so

222

STARTING & DRIVING

Internal Loading

DO NOT carry unsecured equipment, tools

General Towing Safety

Your vehicle can tow a trailer if you carefully observe load

limits, use approved equipment, and follow the towing

guidelines. Always check load limits before towing.

or luggage that could move, causing personal

injury in the event of an accident, emergency

braking or hard acceleration.

Towing loads in excess of the maximum towing weight

can seriously affect vehicle handling and performance, and

could damage your vehicles engine and drive-train.

DO NOT obstruct the driver and passengers

to keep right sitting posture and observation

with loads.

Note: Exceeding any load limits advised by MG Motor

UK Ltd is dangerous. Consult the recommended load

limits and loading prior to any journey.

4

Folding the rear seats can increase luggage space, refer to

"Rear Seat" in "Seats and Restraints" chapter.

Check the loading of your vehicle and trailer

carefully before starting to drive.

When cargo is loaded in the vehicle, place it at a position

as low as possible and ensure that it is tightly secured, so as

to avoid personal injury caused by cargo movement when

trafﬁc accidents or emergency brakes occur. If the cargo

has to be put on a seat, no one is allowed to sit on that

seat.

Trailer hitch load should never exceed the limit advised by

MG Motor UK Ltd.

Note: Excessive towing loads reduce front tyre traction

and steering control, too little trailer nose load can

make the trailer unstable and cause it to sway.

Tow bars: Only genuine MG approved tow bars should

be ﬁtted to your vehicle. Only use the attachment method

speciﬁed by the vehicle manufacturer for securing the

223

STARTING & DRIVING

towing hitch. Contact your authorised MG dealer for

more information.

can affect your vehicles braking efﬁciency if Automated

Stop/Start is activated on a hill while towing a trailer.

Safety chains: Safety chains must be used as

a

precautionary measure should the trailer become

unintentionally unhitched. Make sure the safety chain is

securely attached to both the trailer and the vehicle prior

to departure.

Altitude: Your engine delivers less power at higher

altitude. If you tow a trailer in a mountainous area you

should reduce the combined vehicle and trailer weight by

10% for every 1000m of elevation.

Gradients: Where possible, when towing, you should

plan your journey to avoid steep gradients. The advised

brake towing mass stated assumes a maximum gradient

capability of 12% where possible it is recommended you

drive on gradients less than 12%. Follow the trailer

associations recommendations for suitable roads.

Running in period: Avoid towing a trailer during your

vehicles ﬁrst 1000 km or 625 miles.

Stop/Start function: Manually switch the Automated

Stop/Start function OFF when towing. The trailer weight

224

Starting & Driving for Your Mg Zs SUV First Generation (2017-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals