Get Maintenance -> Replacement of lamp bulbs Guide for Mitsubishi Outlander SUV 2020

Replacement of lamp bulbs

4. Insert a new fuse of the same capacity

by using the fuse puller into the same

place in the fuse block.

CAUTION

Do not install commercially available LED-

type bulbs.

CAUTION

Never hold the halogen lamp bulb with a

bare hand, dirty glove, etc.

l

Commercially available LED-type bulbs

could adversely affect the operation of the

vehicle, such as by preventing the lamps and

other vehicle equipment from operating

properly.

The oil from your hand could cause the bulb

to break the next time the headlamps are op-

erated.

If the glass surface is dirty, it must be

cleaned with alcohol, paint thinner, etc., and

refit it after drying thoroughly.

Bulbs are extremely hot immediately after

being turned off.

l

When replacing a bulb, wait for it to cool

sufficiently before touching it. You could

otherwise be burnt.

Handle halogen lamp bulbs with care. The

gas inside a halogen lamp bulbs is highly

pressurized, so dropping, knocking, or

scratching a halogen lamp bulb can cause it

to shatter.

CAUTION

If the newly inserted fuse blows again after a

l

short time, we recommend you to have the

electrical system checked to find the cause

and rectify it.

11

NOTE

Never use a fuse with a larger capacity than

l

specified or a substitute (such as a cable or

foil). Doing so could cause the circuit wires

to overheat and create a fire.

If you are unsure of how to carry out the

work as required, we recommend you to

consult a specialist.

Be careful not to scratch the vehicle body

when removing a lamp or lens.

l

Replacement of lamp bulbs

Before replacing a bulb, ensure the lamp is

off. Do not touch the glass part of the new

bulb with your bare fingers; the skin oil left

on the glass will evaporate when the bulb

gets hot and the vapour will condense on the

reflector and dim the surface.

Maintenance

11-23

OGGE20E1

Replacement of lamp bulbs

3- Headlamps, low beam

Halogen: 55 W (H7)

LED: −

4- Position lamps: −

Daytime running lamps: −

5- Front fog lamps

Halogen: 19 W (H16)

LED: −

Outside

NOTE

When it rains or when the vehicle has been

l

washed, the inside of the lens sometimes be-

comes foggy. This is the same phenomenon

as when window glass mists up on a humid

day, and does not indicate a functional prob-

lem.

When the lamp is switched on, the heat will

remove the fog. However, if water gathers

inside the lamp, we recommend you to have

the lamp checked.

Front

6- Side turn-signal lamps: −

Codes in parentheses indicate bulb types.

Bulb location and capacity

Type A

Type B

NOTE

The following lamps use an LED instead of

the bulb. If you need to repair or replace

these lamps, contact

MOTORS Authorized Service Point.

l

CAUTION

a

MITSUBISHI

When replacing a bulb, be sure to use a new

l

bulb of the same type, wattage and colour. If

you install a different bulb, the bulb could

malfunction or fail to come on and could

lead to a vehicle fire.

Headlamps, high-beam (LED type)

Headlamps, low beam (LED type)

Position lamps

Daytime running lamps

Front fog lamps (LED type)

Side turn-signal lamps

•

11

Type A: Halogen headlamps type

Type B: LED headlamps type

1- Front turn-signal lamps: 21 W (PY21W)

2- Headlamps, high-beam

Halogen: 60 W (HB3)

LED: −

11-24

Maintenance

OGGE20E1

Replacement of lamp bulbs

Rear

NOTE

The following lamps use an LED instead of

the bulb.

The following lamps use an LED instead of

the bulb. If you need to repair or replace

l

If you need to repair or replace these lamps,

contact a MITSUBISHI MOTORS Author-

ized Service Point.

these lamps, contact

MOTORS Authorized Service Point.

a

MITSUBISHI

Downlight

Front foot lamps

•

High-mounted stop lamp

Tail lamps

Stop lamps

•

Headlamps (low beam, halogen

bulb)

1. When replacing the bulb on the left side

of the vehicle, remove the bolt (A) hold-

ing down the relay box and move the re-

lay box.

Inside

1- High-mounted stop lamp: −

2- Tail lamps: −

3- Charging port courtesy lamp: 5W

(W5W)

4- Rear fog lamp (LHD vehicles): 21 W

(W21W)

Reversing lamp (RHD vehicles): 16 W

(W16W)

11

5- Licence plate lamps: 5 W (W5W)

6- Reversing lamp (LHD vehicles): 16 W

(W16W)

Rear fog lamp (RHD vehicles): 21 W

(W21W)

7- Rear turn-signal lamps: 21 W (WY21W)

8- Stop lamps: −

1- Luggage room lamp: 8 W

2- Room lamp (rear): 8 W

3- Map & room lamps (front): 8 W

4- Downlight

*: Front of the vehicle

5- Vanity mirror lamps: 2 W

6- Glove box lamp: 1.4 W

Codes in parentheses indicate bulb types.

Maintenance

11-25

OGGE20E1

Replacement of lamp bulbs

2. Turn the cap (B) anticlockwise to re-

move it.

*: Front of the vehicle

NOTE

When installing the bulb, align the tab (D)

with the notch (E) of the socket.

l

2. Turn the cap (B) anticlockwise to re-

move it.

*: Front of the vehicle

Headlamps (high-beam, halo-

gen bulb)

1. When replacing the bulb on the right

side of the vehicle, remove the clip (A)

holding down the washer tank spout and

then move it.

3. Turn the socket (C) anticlockwise to re-

move it, and then pull the bulb out of the

socket.

*: Front of the vehicle

11

4. To install the bulb, perform the removal

steps in reverse.

11-26

Maintenance

OGGE20E1

Replacement of lamp bulbs

3. Turn the bulb (C) anticlockwise to re-

move it, and then while holding down

the tab (D), pull out the bulb (E).

1. Remove the 12 clips (A, B), and then re-

move the cover (C).

*: Front of the vehicle

4. To install the bulb, perform the removal

steps in reverse.

3. To install the bulb, perform the removal

steps in reverse.

2. Turn the socket (D) anticlockwise to re-

move it, then remove the bulb from the

socket by turning it anticlockwise while

pressing in.

11

Front turn-signal lamps

Front fog lamps (Halogen bulb

type)*

CAUTION

Make sure that the Plug-in Hybrid EV sys-

1. Insert a straight blade (or minus) screw-

driver with a cloth over its tip at the

l

tem have cooled down before replacing the

bulb on the right side of the vehicle, other-

wise you could be burnt by the radiator hose.

Maintenance

11-27

OGGE20E1

Replacement of lamp bulbs

points indicated by arrows and pry gen-

tly to remove the cover (A).

4. Turn the bulb (F) anticlockwise to re-

move it.

NOTE

When unfastening the screws of the fog

lamp, be careful not to mistakenly move the

beam position adjustment screw (C).

l

2. Remove the 3 screws (B) and remove

the lamp unit.

5. To install the bulb, perform the removal

steps in reverse.

3. While holding down the tab (D), pull out

the socket (E).

11

11-28

Maintenance

OGGE20E1

Replacement of lamp bulbs

2. Turn the socket (A) anticlockwise to re-

move it, and then pull the bulb out of the

socket.

Rear fog lamp (driver’s side)/

Reversing lamp (Passenger’s

side)

1. Insert a straight blade (or minus) screw-

driver with a cloth over its tip at the edge

of the lamp unit, and then push the lamp

unit upward to remove it.

NOTE

When installing the lamp unit, first insert the

notch (B) into the hole on the body, and then

push on the lamp unit to fit it into place.

l

Rear combination lamps

1. Open the tailgate.

3. To install the bulb, perform the removal

steps in reverse.

2. Remove the screws (A), and then move

the lamp unit towards the rear of the ve-

hicle to unfix the notch (B) and pins (C)

of the lamp unit.

11

Maintenance

11-29

OGGE20E1

Replacement of lamp bulbs

3. Turn the socket anticlockwise and re-

move it, and then pull the bulb out of the

socket.

2. Insert a minus screwdriver with the end

covered with a cloth or other object to

press the hook (B) aside and remove the

lens.

NOTE

When installing the lamp unit, align the

notch (F) and pin (G) on the lamp unit with

the clip (H) and hole (I) in the body.

l

Licence plate lamps

1. Remove while pressing the lamp unit

(A) to the left side of the vehicle.

D- Rear turn-signal lamp

3. Remove the bulb from the socket.

E- Tail lamp and stop lamp (LED)-cannot

be replaced

11

NOTE

The tail lamp and stop lamp use an LED in-

stead of the bulb.

l

If you need to repair or replace these lamps,

contact a MITSUBISHI MOTORS Author-

ized Service Point.

4. To install the bulb, perform the removal

steps in reverse.

4. To install the bulb, perform the removal

steps in reverse.

11-30

Maintenance

OGGE20E1

Replacement of lamp bulbs

NOTE

When installing the lamp unit, first insert the

end of tab (C) and then align tab (D).

l

11

Maintenance

11-31

OGGE20E1

Maintenance -> Replacement of lamp bulbs for Your Mitsubishi Outlander SUV 2020

Related Topics

General information

Charging

Locking and unlocking

Seats and seat belts

Instruments and controls

Starting and driving

For pleasant driving

For emergencies

Vehicle care

Maintenance

Specifications