Get In case of emergency -> Flat tire Guide for Nissan Juke SUV First Generation (2010-2019)

FLAT TIRE

If you have a flat tire, follow the instructions as follows.

STOPPING VEHICLE

clear of the vehicle.

Spare tire

PREPARING TOOLS AND SPARE TIRE

WARNING:

Be sure to apply the parking brake firmly.

Be sure to move the shift lever to the “P”

(Park) position (Continuously Variable

Transmission models) or the shift lever to

the “R” (Reverse) position (Manual Transmis-

sion models).

Never change tires when the vehicle is on a

slope, ice or slippery area. This is hazardous.

SCE0980

1. Raise the floor board.

Never change tires when the oncoming

traffic is close to your vehicle. Call for

professional road assistance.

2. Remove the cargo floor box.

3. Remove the spacer

and loosen the clamp

1. Safely move the vehicle off the road away from

traffic.

BLOCKING WHEELS

2. Turn on the hazard indicator flasher lights.

3. Park on a level surface.

4. Apply the parking brake.

5. Continuously Variable Transmission (CVT) mod-

els: Move the shift lever to the “P” (Park) position.

Manual Transmission (MT) models: Move the shift

lever to the “R” (Reverse) position.

SCE0946

Jacking tools

Open the back door. Raise the cargo floor board

Remove jacking tools.

6. Turn off the engine.

7. Open the hood and set up the triangle reflector (if

equipped):

MCE0001D

To warn other traffic.

WARNING:

To signal professional road assistance person-

nel that you need assistance.

Be sure to block the appropriate wheel to

prevent the vehicle from moving, which may

cause personal injury.

8. Have all passengers get out from the vehicle and

stand in a safe place, away from other traffic and

In case of emergency 6-3

Place suitable blocks

at both the front and back of

Jacking up vehicle

the wheel diagonally opposite the flat tire

prevent the vehicle from moving when it is jacked up.

REMOVING TIRE

Removing wheel cover (if equipped)

SCE0948

Jack-up points

SCE0630

WARNING:

Never use your hands to remove the wheel

cover. This may cause personal injury.

To remove the wheel cover, use the jack rod

illustrated.

Apply cloth

between the wheel and jack rod to

prevent damaging the wheel and wheel cover.

6-4 In case of emergency

Removing tire

1. Remove the wheel nuts.

2. Remove the damaged tire.

CAUTION:

The tire is heavy. Be sure that your feet are clear

from the tire and use gloves as necessary to

avoid injury.

SCE0504

INSTALLING SPARE TIRE

Be sure to read the caution label attached to

the jack body before using.

WARNING:

Be sure to read and follow the instructions in

this section.

1. Place the jack directly under the jack-up point as

illustrated so that the top of the jack contacts the

vehicle at the jack-up point.

Do not get under a vehicle that is supported

only by a jack: Use vehicle support stands.

The jack should be placed on firm level

ground.

Never use a jack which is not provided with

your vehicle.

2. Align the jack head between the two notches

located at the jack-up point of either the front or

the rear section.

The jack, which is provided with your vehicle,

is designed only to lift your vehicle during a

tire change. Do not use the jack provided

with your vehicle on other vehicles.

SCE0039

3. Fit the groove of the jack head between the

notches as shown.

WARNING:

Never jack up the vehicle at a location other

than the jack-up point that is specified.

Never use wheel nuts which are not provided

with your vehicle. Incorrect wheel nuts or

improperly tightened wheel nuts may cause

the wheel to become loose or come off. This

could cause an accident.

4. Loosen each wheel nut, counterclockwise, one or

two turns with the wheel nut wrench.

Never lift the vehicle more than necessary.

Never use blocks on or under the jack.

Do not remove the wheel nuts until the tire is

off the ground.

Never start or run the engine while the

vehicle is on the jack. The vehicle may move

suddenly, and this may cause an accident.

5. Carefully raise the vehicle until the clearance

between the tire and ground is achieved.

Never use oil or grease on the wheel studs

or nuts. This may cause the wheel nuts to

become loose.

6. To lift the vehicle, securely hold the jack lever and

rod with both hands and turn the jack lever.

Never allow passengers to remain in the

vehicle while the tire is off the ground.

The T-type spare tire is designed for emer-

gency use only.

In case of emergency 6-5

JUMP STARTING

1. Clean any mud or dirt from the surface between

the wheel and hub.

For models equipped with the Tire Pressure

Monitoring System (TPMS)

After adjusting the tire pressure, the TPMS must be

reset. See “Tire Pressure Monitoring System (TPMS)”

(P.5-3) for details about the resetting procedure.

WARNING:

Incorrect jump starting can lead to a battery

explosion. The battery explosion may result

in severe injury or death. It may also result in

damage to the vehicle. Be sure to follow the

instructions in this section.

2. Carefully put the spare tire on and tighten the

wheel nuts with your fingers. Check that all the

wheel nuts contact the wheel surface horizontally.

3. Tighten the wheel nuts alternately and evenly in

STOWING DAMAGED TIRE AND TOOLS

the sequence illustrated (

), more than 2

* *

Explosive hydrogen gas is always present in

the vicinity of the battery. Keep all sparks

and flames away from the battery.

times with the wheel nut wrench, until they are

tight.

WARNING:

Be sure that the tire, jack and tools used are

properly stored after use. Such items can

become dangerous projectiles in an accident

or sudden stop.

4. Lower the vehicle slowly until the tire touches the

ground.

Always wear suitable eye protection and

remove rings, bracelets, and any other jew-

elry whenever working on or near a battery.

5. Tighten the wheel nuts securely, with the wheel

nut wrench, in the sequence illustrated.

The T-type spare tire is designed for emer-

gency use only.

Never lean over the battery while jump

starting.

6. Lower the vehicle completely.

Tighten the wheel nuts to the specified torque

with a torque wrench as soon as possible.

Never allow battery fluid to come into

contact with eyes, skin, clothes or the

vehicle’s painted surfaces. Battery fluid is a

corrosive sulfuric acid which can cause

severe burns. If the fluid comes into contact

with anything, immediately flush the con-

tacted area with plenty of water.

1. Securely store the jack, tools and the damaged

tire in the storage area.

Wheel nut tightening torque:

108 N·m (11 kg-m, 80 ft-lb)

2. Replace the cargo floor box and the floor board.

3. Close the back door.

The wheel nuts must be kept tightened to

specification at all times. It is recommended

that the wheel nuts be tightened to specification

at each lubrication interval.

Keep the battery out of the reach of children.

The booster battery must be rated at 12

volts. Use of an incorrectly rated battery will

damage your vehicle.

WARNING:

Retighten the wheel nuts when the vehicle has

been driven for 1,000 km (600 miles) (also in

cases of a flat tire, etc.).

Never attempt to jump start a frozen battery.

It could explode and cause serious injury.

6-6 In case of emergency

In case of emergency -> Flat tire for Your Nissan Juke SUV First Generation (2010-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals