Get Safety?Seats, seat belts and supplemental restraint system -> Child restraints Guide for Nissan Micra 4 Door Fifth Generation (2017-2023)

CHILD RESTRAINTS

– The child restraint must be used

and installed properly. Always fol-

low all of the child restraint manu-

facturer’s instructions for installa-

tion and use.

– Infants and children should never

be held on anyone’s lap. Even the

strongest adult cannot resist the

forces of a collision.

– Do not put a seat belt around both

a child and another passenger.

– NISSAN recommends that all child

restraints be installed in the rear

seat. Studies show that children

are safer when properly restrained

in the rear seat than in the front

seat. If you must install a forward-

facing child restraint in the front

seat, refer to “Forward-facing child

restraint installation using the seat

belts” in this section.

ARS1098

WRS0256

PRECAUTIONS ON CHILD

RESTRAINTS

WARNING

∙ Failure to follow the warnings and in-

structions for proper use and installa-

tion of child restraints could result in

serious injury or death of a child or

other passengers in a sudden stop or

collision:

– Even with the NISSAN Advanced Air

Bag System, never install a rear-

facing child restraint in the front

seat. An inflating air bag could se-

riously injure or kill a child. A rear-

facing child restraint must only be

used in the rear seat.

Safety—Seats, seat belts and supplemental restraint system 1-23

Several manufacturers offer child re-

straints for infants and children of various

sizes. When selecting any child restraint,

keep the following points in mind:

– Be sure to purchase a child re-

straint that will fit the child and ve-

hicle. Some child restraints may

not fit properly in your vehicle.

– Infants and children should always

be placed in an appropriate child

restraint while in the vehicle.

∙ When the child restraint is not in use,

keep it secured with the LATCH system

or a seat belt. In a sudden stop or col-

lision, loose objects can injure occu-

pants or damage the vehicle.

∙

Choose only a restraint with a label cer-

tifying that it complies with Canadian

Motor Vehicle Safety Standard 213.

– Child restraint anchorages are de-

signed to withstand only those

loads imposed by correctly fitted

child restraints. Under no circum-

stances are they to be used to at-

tach adult seat belts, or other items

or equipment to the vehicle. Doing

so could damage the child re-

straint anchorages. The child re-

straint will not be properly in-

Check the child restraint in your vehicle

to be sure it is compatible with the vehi-

cle’s seat and seat belt system.

CAUTION

A child restraint in a closed vehicle can

become very hot. Check the seating

surface and buckles before placing a

child in the child restraint.

If the child restraint is compatible with

your vehicle, place your child in the child

restraint and check the various adjust-

ments to be sure the child restraint is

compatible with your child. Choose a

child restraint that is designed for your

child’s height and weight. Always follow

all recommended procedures.

stalled

using

the

damaged

anchorage, and a child could be se-

This vehicle is equipped with a universal

child restraint anchor system, referred to

as the LATCH (Lower Anchors and Tethers

for CHildren) system. Some child restraints

include rigid or webbing-mounted attach-

ments that can be connected to these an-

chors. For additional information, refer to

“LATCH (Lower Anchors and Tethers for

CHildren) system” in this section.

riously injured or killed in

collision.

a

– Never use the anchor points for

adult seat belts or harnesses.

∙

If the combined weight of the child and

child restraint is less than 29.5 kg

(65 lbs.), you may use either the LATCH

anchors or the seat belt to install the

child restraint (not both at the same

time).

– A child restraint with a top tether

strap should not be used in the

front passenger seat.

– Keep seatbacks as upright as pos-

sible after fitting the child

restraint.

If you do not have a LATCH compatible

child restraint, the vehicle seat belts can be

used.

1-24 Safety—Seats, seat belts and supplemental restraint system

∙

If the combined weight of the child and

child restraint is greater than 29.5 kg

(65 lbs.), use the vehicle’s seat belt (not

the lower anchors) to install the child

restraint.

install the child restraint. Be sure to follow

the child restraint manufacturer’s instruc-

tions for installation.

The LATCH anchor points are provided to

install child restraints in the rear outboard

seating positions only. Do not attempt to

install a child restraint in the center position

using the LATCH anchors.

Be sure to follow the child restraint

manufacturer’s instructions for installa-

tion.

All Canadian provinces or territories re-

quire that infants and small children be

restrained in an approved child restraint

at all times while the vehicle is being op-

erated. Canadian law requires the top

tether strap on forward-facing child re-

straints be secured to the designated

anchor point on the vehicle.

LATCH lower anchor

WARNING

Failure to follow the warnings and in-

structions for proper use and installa-

tion of child restraints could result in

serious injury or death of a child or

other passengers in a sudden stop or

collision:

LRS2761

LATCH system lower anchor locations

LATCH (Lower Anchors and

Tethers for CHildren) SYSTEM

Your vehicle is equipped with special an-

chor points that are used with LATCH sys-

tem compatible child restraints. This sys-

tem may also be referred to as the ISOFIX

or ISOFIX compatible system. With this sys-

tem, you do not have to use a vehicle seat

belt to secure the child restraint unless the

combined weight of the child and child re-

straint exceeds 29.5 kg (65 lbs.). If the com-

bined weight of the child and child restraint

is greater than 29.5 kg (65 lbs.) use the ve-

hicle’s seat belt (not the lower anchors) to

– Attach LATCH system compatible

child restraints only at the loca-

tions shown in the illustration.

– Do not secure a child restraint in

the center rear seating position us-

ing the LATCH lower anchors. The

child restraint will not be secured

properly.

Safety—Seats, seat belts and supplemental restraint system 1-25

– Inspect the lower anchors by in-

serting your fingers into the lower

anchor area. Feel to make sure

there are no obstructions over the

anchors such as seat belt webbing

or seat cushion material. The child

restraint will not be secured prop-

erly if the lower anchors are

obstructed.

Child restraint anchorages are de-

signed to withstand only those loads

imposed by correctly fitted child re-

straints. Under no circumstances are

they to be used to attach adult seat

belts, or other items or equipment to

the vehicle. Doing so could damage the

child restraint anchorages. The child re-

straint will not be properly installed us-

ing the damaged anchorage, and a

child could be seriously injured or killed

in a collision.

LRS3036

LRS0661

LATCH webbing-mounted attachment

Installing child restraint LATCH

LATCH lower anchor location

The LATCH lower anchors are located as

shown. A label is attached to the seatback

to help you locate the LATCH lower an-

chors.

lower anchor attachments

LATCH compatible child restraints include

two rigid or webbing-mounted attach-

ments that can be connected to two an-

chors located at certain seating positions

in your vehicle. With this system, you do not

have to use a vehicle seat belt to secure the

child restraint. Check your child restraint for

a label stating that it is compatible with

LATCH. This information may also be in the

instructions provided by the child restraint

manufacturer.

1-26 Safety—Seats, seat belts and supplemental restraint system

LRS0662

LRS2467

LRS2444

LATCH rigid-mounted attachment

When installing a child restraint, carefully

read and follow the instructions in this

manual and those supplied with the child

restraint.

Safety—Seats, seat belts and supplemental restraint system 1-27

Top tether anchor point locations

REAR-FACING CHILD RESTRAINT

INSTALLATION USING LATCH

For additional information, refer to all Warn-

ings and Cautions in the “Child safety” and

“Child restraints” sections of this manual

before installing a child restraint.

WARNING

Child restraint anchorages are de-

signed to withstand only those loads

imposed by correctly fitted child re-

straints. Under no circumstances are

they to be used to attach adult seat

belts, or other items or equipment to

the vehicle. Doing so could damage the

child restraint anchorages. The child re-

straint will not be properly installed us-

ing the damaged anchorage, and a

child could be seriously injured or killed

in a collision.

Do not use the lower anchors if the com-

bined weight of the child and the child re-

straint exceeds 29.5 kg (65 lbs.). If the com-

bined weight of the child and the child

restraint is greater than 29.5 kg (65 lbs.), use

the vehicle’s seat belt (not the lower an-

chors) to install the child restraint. Be sure

to follow the child restraint manufacturer’s

instructions for installation.

WRS0801

Rear-facing webbing-mounted – step 2

The child restraint top tether strap must be

used when installing the child restraint with

the LATCH lower anchor attachments or

seat belts. For additional information, refer

to “Installing top tether strap” in this sec-

tion.

2. Secure the child restraint anchor at-

tachments to the LATCH lower an-

chors. Check to make sure the LATCH

attachment is properly attached to the

lower anchors.

Follow these steps to install a rear-facing

child restraint using the LATCH system:

1. Position the child restraint on the seat.

Always follow the child restraint manu-

facturer’s instructions.

If you have any questions when install-

ing a top tether strap child restraint, it is

recommended that you visit a NISSAN

dealer for this service.

1-28 Safety—Seats, seat belts and supplemental restraint system

WRS0802

LRS0673

LRS0674

Rear-facing rigid-mounted – step 2

Rear-facing – step 3

Rear-facing – step 4

3. For child restraints that are equipped

with webbing-mounted attachments,

remove any additional slack from the

anchor attachments. Press downward

and rearward firmly in the center of the

child restraint with your hand to com-

press the vehicle seat cushion and

seatback while tightening the webbing

of the anchor attachments.

4. After attaching the child restraint, test

it before you place the child in it. Push it

from side to side while holding the child

restraint near the LATCH attachment

path. The child restraint should not

move more than 25 mm (1 in), from side

to side. Try to tug it forward and check

to see if the LATCH attachment holds

the restraint in place. If the restraint is

not secure, tighten the LATCH attach-

ment as necessary, or put the restraint

in another seat and test it again. You

may need to try a different child re-

straint or try installing by using the ve-

Safety—Seats, seat belts and supplemental restraint system 1-29

hicle seat belt (if applicable). Not all

child restraints fit in all types of vehicles.

Do not use the lower anchors if the com-

bined weight of the child and the child re-

straint exceeds 29.5 kg (65 lbs.). If the com-

bined weight of the child and the child

restraint is greater than 29.5 kg (65 lbs.), use

the vehicle’s seat belt (not the lower an-

chors) to install the child restraint. Be sure

to follow the child restraint manufacturer’s

instructions for installation.

5. Check to make sure the child restraint

is properly secured prior to each use. If

the child restraint is loose, repeat

steps 1 through 4.

REAR-FACING CHILD RESTRAINT

INSTALLATION USING THE SEAT

BELTS

Follow these steps to install a rear-facing

child restraint using the vehicle seat belts in

the rear seats:

WARNING

The three-point seat belt with Auto-

matic Locking Retractor (ALR) must be

used when installing a child restraint.

Failure to use the ALR mode will result in

the child restraint not being properly

secured. The restraint could tip over or

be loose and cause injury to a child in a

sudden stop or collision.

WRS0256

Rear-facing – step 1

1. Child restraints for infants must be

used in the rear-facing direction and

therefore must not be used in the

front seat. Position the child restraint

on the seat. Always follow the child re-

straint manufacturer’s instructions.

For additional information, refer to all Warn-

ings and Cautions in the “Child safety” and

“Child restraints” sections of this manual

before installing a child restraint.

1-30 Safety—Seats, seat belts and supplemental restraint system

WRS0761

LRS2395

LRS2396

Rear-facing – step 2

Rear-facing – step 3

Rear-facing – step 4

2. Route the seat belt tongue through the

child restraint and insert it into the

buckle until you hear and feel the latch

engage. Be sure to follow the child re-

straint manufacturer’s instructions for

belt routing.

3. Pull the shoulder belt until the belt is

fully extended. At this time, the seat belt

retractor is in the ALR mode (child re-

straint mode). It reverts to the ELR

mode when the seat belt is fully re-

tracted.

4. Allow the seat belt to retract. Pull up on

the shoulder belt to remove any slack

in the belt.

Safety—Seats, seat belts and supplemental restraint system 1-31

7. Check to make sure that the child re-

straint is properly secured prior to each

use. If the seat belt is not locked, repeat

steps 1 through 6.

After the child restraint is removed and the

seat belt fully retracted, the ALR mode

(child restraint mode) is canceled.

FORWARD-FACING CHILD

RESTRAINT INSTALLATION USING

LATCH

For additional information, refer to all Warn-

ings and Cautions in the “Child safety” and

“Child restraints” sections of this manual

before installing a child restraint.

WRS0762

LRS2397

Rear-facing – step 5

Rear-facing – step 6

5. Remove any additional slack from the

seat belt; press downward and rear-

ward firmly in the center of the child

restraint to compress the vehicle seat

cushion and seatback while pulling up

on the seat belt.

6. After attaching the child restraint, test

it before you place the child in it. Push it

from side to side while holding the child

restraint near the seat belt path. The

child restraint should not move more

than 25 mm (1 in), from side to side. Try

to tug it forward and check to see if the

belt holds the restraint in place. If the

restraint is not secure, tighten the seat

belt as necessary, or put the restraint in

another seat and test it again. You may

need to try a different child restraint.

Not all child restraints fit in all types of

vehicles.

Do not use the lower anchors if the com-

bined weight of the child and the child re-

straint exceeds 29.5 kg (65 lbs.). If the com-

bined weight of the child and the child

restraint is greater than 29.5 kg (65 lbs.), use

the vehicle’s seat belt (not the lower an-

chors) to install the child restraint. Be sure

to follow the child restraint manufacturer’s

instructions for installation.

1-32 Safety—Seats, seat belts and supplemental restraint system

Follow these steps to install a forward-

facing child restraint using the LATCH sys-

tem:

1. Position the child restraint on the seat.

Always follow the child restraint manu-

facturer’s instructions.

WRS0799

WRS0800

Forward-facing webbing-mounted

–

Forward-facing rigid-mounted – step 2

step 2

seating positions that do not have a

2. Secure the child restraint anchor at-

tachments to the LATCH lower an-

chors. Check to make sure the LATCH

attachment is properly attached to the

lower anchors.

top tether anchor.

3. The back of the child restraint should

be secured against the vehicle seat-

back.

If necessary, adjust or remove the head

restraint/headrest to obtain the cor-

rect child restraint fit. If the head

restraint/headrest is removed, store it

in a secure place. Be sure to reinstall

the head restraint/headrest when

the child restraint is removed. For ad-

ditional information about head

restraint/headrest adjustment, refer to

If the child restraint is equipped with a

top tether strap, route the top tether

strap and secure the tether strap to

the tether anchor point. For additional

information, refer to “Installing top

tether strap” in this section.

Do not install child restraints that re-

quire the use of a top tether strap in

Safety—Seats, seat belts and supplemental restraint system 1-33

“Head restraints/headrests” in this sec-

tion.

If the seating position does not have

an adjustable head restraint/headrest

and it is interfering with the proper

child restraint fit, try another seating

position or a different child restraint.

LRS0671

WRS0697

Forward-facing – step 4

Forward-facing – step 6

4. For child restraints that are equipped

with webbing-mounted attachments,

remove any additional slack from the

anchor attachments. Press downward

and rearward firmly in the center of the

child restraint with your knee to com-

press the vehicle seat cushion and

seatback while tightening the webbing

of the anchor attachments.

6. After attaching the child restraint, test

it before you place the child in it. Push it

from side to side while holding the child

restraint near the LATCH attachment

path. The child restraint should not

move more than 25 mm (1 in), from side

to side. Try to tug it forward and check

to see if the LATCH attachment holds

the restraint in place. If the restraint is

not secure, tighten the LATCH attach-

ment as necessary, or put the restraint

in another seat and test it again. You

may need to try a different child re-

straint. Not all child restraints fit in all

types of vehicles.

5. Tighten the tether strap according to

the manufacturer’s instructions to re-

move any slack.

1-34 Safety—Seats, seat belts and supplemental restraint system

7. Check to make sure the child restraint

is properly secured prior to each use. If

the child restraint is loose, repeat

steps 1 through 6.

Rear bench seat

OUTBOARD SEATING POSITIONS

1. Remove the head restraint/headrest

and store it in a secure place. Be sure to

reinstall the head restraint/headrest

when the child restraint is removed. For

additional information, refer to "Head

restraints/headrests" in this section.

1

2. Position the top tether strap

as

᭺

shown.

3. Secure the tether strap to the tether

2

anchor point

as shown.

᭺

LRS2656

4. Tighten the tether strap according to

the manufacturer’s instructions to re-

move any slack.

Outboard seating positions

Top tether strap

1

᭺

2

Anchor point

᭺

WARNING

Installing top tether strap

The child restraint top tether strap must be

used when installing the child restraint with

the LATCH lower anchor attachments.

Child restraint anchorages are designed

to withstand only those loads imposed

by correctly fitted child restraints. Under

no circumstances are they to be used to

attach adult seat belts, or other items or

equipment to the vehicle. Doing so could

damage the child restraint anchorages.

The child restraint will not be properly

installed using the damaged anchorage,

and a child could be seriously injured or

killed in a collision.

First, secure the child restraint with the

LATCH lower anchors (rear outboard posi-

tions only).

Safety—Seats, seat belts and supplemental restraint system 1-35

Follow these steps to install a forward-

facing child restraint using the vehicle seat

belt in the rear seats or in the front passen-

ger seat:

FORWARD-FACING CHILD

RESTRAINT INSTALLATION USING

THE SEAT BELTS

WARNING

1. If you must install a child restraint in

the front seat, it should be placed in a

forward-facing direction only. Move

the seat to the rearmost position.

Child restraints for infants must be

used in the rear-facing direction and,

therefore, must not be used in the

front seat.

The three-point seat belt with Auto-

matic Locking Retractor (ALR) must be

used when installing a child restraint.

Failure to use the ALR mode will result in

the child restraint not being properly

secured. The restraint could tip over or

be loose and cause injury to a child in a

sudden stop or collision. Also, it can

change the operation of the front pas-

senger air bag. For additional informa-

tion, refer to “Front passenger air bag

and status light” in this section.

2. Position the child restraint on the seat.

Always follow the child restraint manu-

facturer’s instructions.

WRS0699

Forward-facing (front passenger seat) –

step 1

For additional information, refer to all Warn-

ings and Cautions in the “Child safety” and

“Child restraints” sections of this manual

before installing a child restraint.

The back of the child restraint should

be secured against the vehicle seat-

back.

If necessary, adjust or remove the head

restraint/headrest to obtain the cor-

rect child restraint fit. If the head

restraint/headrest is removed, store it

in a secure place. Be sure to reinstall

the head restraint/headrest when

the child restraint is removed. For ad-

ditional information about head

restraint/headrest adjustment, re-

moval and installation, refer to “Head

restraints/headrests” in this section.

Do not use the lower anchors if the com-

bined weight of the child and the child re-

straint exceeds 29.5 kg (65 lbs.). If the com-

bined weight of the child and the child

restraint is greater than 29.5 kg (65 lbs.), use

the vehicle’s seat belt (not the lower an-

chors) to install the child restraint. Be sure

to follow the child restraint manufacturer’s

instructions for installation.

1-36 Safety—Seats, seat belts and supplemental restraint system

If the seating position does not have

an adjustable head restraint/headrest

and it is interfering with the proper

child restraint fit, try another seating

position or a different child restraint.

Do not install child restraints that re-

quire the use of a top tether strap in

seating positions that do not have a

top tether anchor.

WRS0680

Forward-facing – step 3

3. Route the seat belt tongue through the

child restraint and insert it into the

buckle until you hear and feel the latch

engage. Be sure to follow the child re-

straint manufacturer’s instructions for

belt routing.

If the child restraint is equipped with a

top tether strap, route the top tether

strap and secure the tether strap to

the tether anchor point. For additional

information, refer to “Installing top

tether strap” in this section.

Safety—Seats, seat belts and supplemental restraint system 1-37

LRS0667

LRS0668

WRS0681

Forward-facing – step 4

Forward-facing – step 5

Forward-facing – step 6

4. Pull the shoulder belt until the belt is

fully extended. At this time, the seat belt

retractor is in the ALR mode (child re-

straint mode). It reverts to ELR mode

when the seat belt is fully retracted.

5. Allow the seat belt to retract. Pull up on

the shoulder belt to remove any slack

in the belt.

6. Remove any additional slack from the

seat belt; press downward and rear-

ward firmly in the center of the child

restraint with your knee to compress

the vehicle seat cushion and seatback

while pulling up on the seat belt.

7. Tighten the tether strap according to

the manufacturer’s instructions to re-

move any slack.

1-38 Safety—Seats, seat belts and supplemental restraint system

9. Check to make sure the child restraint

is properly secured prior to each use. If

the seat belt is not locked, repeat

steps 2 through 8.

WRS0698

WRS0475

Forward-facing – step 8

Forward-facing — step 10

8. After attaching the child restraint, test

it before you place the child in it. Push it

from side to side while holding the child

restraint near the seat belt path. The

child restraint should not move more

than 25mm (1 in), from side to side. Try

to tug it forward and check to see if the

belt holds the restraint in place. If the

restraint is not secure, tighten the seat

belt as necessary, or put the restraint in

another seat and test it again. You may

need to try a different child restraint.

Not all child restraints fit in all types of

vehicles.

10. If the child restraint is installed in the

front passenger seat, place the ignition

switch in the ON position. The front

passenger air bag status light

should illuminate. If this light is not illu-

minated, refer to “Front passenger air

bag and status light” in this section.

Move the child restraint to another

seating position. Have the system

checked. It is recommended that you

visit a NISSAN dealer for this service.

After the child restraint is removed and the

seat belt is fully retracted, the ALR mode

(child restraint mode) is canceled.

Safety—Seats, seat belts and supplemental restraint system 1-39

3. Secure the tether strap to the tether

2

anchor point

as shown.

᭺

4. Tighten the tether strap according to

the manufacturer’s instructions to re-

move any slack.

CENTER SEATING POSITION

1

1. Position the top tether strap

shown.

as

᭺

2. Secure the tether strap to the tether

2

anchor point

as shown.

᭺

3. Tighten the tether strap according to

the manufacturer’s instructions to re-

move any slack.

LRS2656

LRS2657

Outboard seating positions

Center seating position

Rear bench seat

1

Top tether strap

᭺

If you have any questions when install-

ing a top tether strap, it is recommended

that you visit a NISSAN dealer for this

service.

2

Anchor point

OUTBOARD SEATING POSITIONS

᭺

1. Remove the head restraint/headrest

and store it in a secure place. Be sure to

reinstall the head restraint/headrest

when the child restraint is removed. For

additional information about head

restraint/headrest adjustment, re-

moval and installation, refer to “Head

restraints/headrests” in this section.

Installing top tether strap

The child restraint top tether strap must be

used when installing the child restraint with

the seat belts.

First, secure the child restraint with the seat

belt.

1

2. Position the top tether strap

shown.

as

᭺

1-40 Safety—Seats, seat belts and supplemental restraint system

Precautions on booster seats

WARNING

Child restraint anchorages are de-

signed to withstand only those loads

imposed by correctly fitted child re-

straints. Under no circumstances are

they to be used to attach adult seat

belts, or other items or equipment to

the vehicle. Doing so could damage the

child restraint anchorages. The child re-

straint will not be properly installed us-

ing the damaged anchorage, and a

child could be seriously injured or killed

in a collision.

WARNING

If a booster seat and seat belt are not

used properly, the risk of a child being

injured or killed in a sudden stop or col-

lision greatly increases:

– Make sure the shoulder portion of

the belt is away from the child’s

face and neck and the lap portion

of the belt does not cross the

stomach.

– Make sure the shoulder belt is not

behind the child or under the

child’s arm.

LRS2479

BOOSTER SEATS

For additional information on installing a

booster seat in your vehicle, follow the in-

structions outlined in this section.

A.

B.

Low back booster seat

High back booster seat

– A booster seat must only be in-

stalled in a seating position that

has a lap/shoulder belt.

Safety—Seats, seat belts and supplemental restraint system 1-41

∙

If the booster seat is compatible with

your vehicle, place the child in the

booster seat and check the various ad-

justments to be sure the booster seat is

compatible with the child. Always follow

all recommended procedures.

All Canadian provinces or territories re-

quire that infants and small children be

restrained in an approved child restraint

at all times while the vehicle is being op-

erated.

The instructions in this section apply to

booster seat installation in the rear seats

or the front passenger seat.

LRS0453

LRS0464

∙

Make sure the child’s head will be prop-

erly supported by the booster seat or

vehicle seat. The seatback must be at

or above the center of the child’s ears.

For example, if a low back booster seat

is chosen, the vehicle seatback must be

at or above the center of the child’s ears.

If the seatback is lower than the center

of the child’s ears, a high back booster

seat should be used.

Booster seats of various sizes are offered

by several manufacturers. When selecting

any booster seat, keep the following points

in mind:

Booster seat installation

WARNING

To avoid injury to child, do not use the

lap/shoulder belt in the Automatic

Locking Retractor (ALR) mode when us-

ing a booster seat with the seat belts.

∙

Choose only a booster seat with a label

certifying that it complies with Cana-

dian Motor Vehicle Safety Standard 213.

For additional information, refer to all Warn-

ings and Cautions in the “Child safety”,

“Child restraints” and “Booster seats” sec-

tions of this manual before installing a child

restraint.

∙

Check the booster seat in your vehicle

to be sure it is compatible with the vehi-

cle’s seat and seat belt system.

1-42 Safety—Seats, seat belts and supplemental restraint system

If the seating position does not have

an adjustable head restraint/headrest

and it is interfering with the proper

booster seat fit, try another seating

position or a different booster seat.

4. Position the lap portion of the seat belt

low and snug on the child’s hips. Be

sure to follow the booster seat manu-

facturer’s instructions for adjusting the

seat belt routing.

5. Pull the shoulder belt portion of the

seat belt toward the retractor to take

up extra slack. Be sure the shoulder

belt is positioned across the top,

middle portion of the child’s shoulder.

Be sure to follow the booster seat

manufacturer’s instructions for adjust-

ing the seat belt routing.

LRS0454

WRS0699

Front passenger position

Follow these steps to install a booster seat

in the rear seat or in the front passenger

seat:

3. The booster seat should be positioned

on the vehicle seat so that it is stable.

If necessary, adjust or remove the head

restraint/headrest to obtain the cor-

rect booster seat fit. If the head

restraint/headrest is removed, store it

in a secure place. Be sure to reinstall

the head restraint/headrest when

the booster seat is removed. For ad-

ditional information, refer to “Head

restraints/headrests” in this section.

1. If you must install a booster seat in

the front seat, move the seat to the

rearmost position.

6. Follow the warnings, cautions and in-

structions for properly fastening a seat

belt shown in “Three-point type seat

belt with retractor” in this section.

2. Position the booster seat on the seat.

Only place it in a front-facing direction.

Always follow the booster seat manu-

facturer’s instructions.

Safety—Seats, seat belts and supplemental restraint system 1-43

Safety?Seats, seat belts and supplemental restraint system -> Child restraints for Your Nissan Micra 4 Door Fifth Generation (2017-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals