Get Audio equipment and telematics Guide for Peugeot 3008 SUV First Generation (2008-2015)

Audio and Telematics

Emergency or assistance call

PEUGEOT Connect SOS

In an emergency, press this

button for more than 2 seconds.

Flashing of the green LED and

a voice message confirm that

the call has been made to the

"PEUGEOT Connect SOS" call

centre*.

If an impact is detected by the airbag

control unit, and independently of

the deployment of any airbags, an

emergency call is made automatically.

If you benefit from the PEUGEOT Connect

Packs offer with the SOS and assistance

pack included, there are additional services

available to you in your MyPEUGEOT

personal space, via the PEUGEOT Internet

website in your country, accessible on

www.peugeot.co.uk.

Pressing this button again immediately cancels

the request.

The green LED goes off.

Pressing this button for more than 8 seconds

cancels the request at any time.

The green LED remains on (without flashing)

when communication is established.

It goes off at the end of the call.

* Subject to the general conditions for the

service available from dealers and to

technological and technical limitations.

"PEUGEOT Connect SOS" immediately locates

your vehicle, starts communication with you in

your language**, and where necessary sends

the appropriate public emergency services**. In

countries where the service is not available, or

when the locating service has been expressly

declined, the call sent directly to the emergency

services (112) without the vehicle location.

** Depending on the geographical cover of

"PEUGEOT Connect SOS", "PEUGEOT

Connect Assistance" and the official national

language selected by the owner of the vehicle.

The list of countries covered and PEUGEOT

CONNECT services is available from dealers

or at www.peugeot.co.uk.

252

Audio and Telematics

PEUGEOT Connect Assistance

Press this button for more than

2 seconds to request assistance

if the vehicle breaks down.

A voice message confirms that

the call has been made**.

Operation of the system

When the ignition is switched

If you purchased your vehicle outside

the PEUGEOT dealer network, we

invite you to have a dealer check the

configuration of these services and, if

desired, modified to suit your wishes.

In a multi-lingual country, configuration

is possible in the official national

language of your choice.

on, the green LED comes on for

3 seconds indicating that the

system is operating correctly.

Pressing this button again immediately cancels

the request.

The cancellation is confirmed by a voice

message.

If the orange LED flashes then

goes off: there is a system fault.

The orange LED is on continuously: the backup

battery must be replaced.

For technical reasons and in particular

to improve the quality of "PEUGEOT

CONNECT services" services to

customers, the manufacturer reserves

the right to carry out updates to the

vehicle's on-board telematic system.

In either case, the emergency and assistance

calls may not function.

Contact a qualified repairer as soon as

possible.

A fault with the system does not

prevent the vehicle being driven.

** Depending on the geographical cover of

"PEUGEOT Connect SOS", "PEUGEOT

Connect Assistance" and the official national

language selected by the owner of the vehicle.

The list of countries covered and PEUGEOT

CONNECT services is available from dealers

or at www.peugeot.co.uk.

.

253

PEUGEOT Connect Navigation (RT6)

GPS navigation system

Multimedia audio system

Bluetooth^®telephone

CONTENTS

256

258

259

261

274

277

287

292

298

299

300

304

01 First steps - Control panel

02 Steering mounted controls

03 General operation

04 Navigation - Guidance

05 Traffic information

06 Using the telephone

07 Radio

p.

The system is protected in such a way that it will only

operate in your vehicle.

08 Music media players

09 Audio settings

As a safety measure, the driver must only carry out

operations which require prolonged attention while the

vehicle is stationary.

When the engine is switched off and to prevent

discharging of the battery, the system switches off

following the activation of the energy economy mode.

10 Configuration

11 Screen menu maps

Frequently asked questions

255

FIRST STEPS

01

Select:

Selection and OK conﬁrmation knob:

Selection of an item on the screen or in a list or a menu,

then conﬁrmation with a short press.

Other than for menus and lists, a short press displays a

contextual menu depending on the current screen.

Rotation with map displayed: zoom the map scale in

and out.

-

the previous/next line in a list or menu.

the previous / next media folder.

step by step selection of the previous/

next radio frequency.

Open the

"Conﬁguration" menu.

Long press: access

to the GPS coverage

and the navigation

demonstration mode.

-

the previous / next MP3 folder.

Move up/down, in "Move the map" mode.

Short press without the

engine running: on / off.

Short press with the engine

running: audio source off /

restore.

Volume adjustment (each

source is independent,

including TA messages and

navigation instructions).

Open the "Trafﬁc

Abandon the current

Select:

MODE button: Selection

of the type of permanent

display.

Long press: black screen

(DARK).

Access to the

information" menu

operation, up one level

"Navigation - guidance"

menu and display the

recent destinations.

-

the next lower / higher radio

frequency automatically.

the previous / next CD track,

MP3 track or media.

the left / right of the screen when a

menu is displayed.

and display the current in the menu.

trafﬁc alerts.

Long press: return to

the permanent display.

Move left / right in "Move the map" mode.

256

FIRST STEPS

01

Access to the "RADIO" menu and

display the list of stations received.

Access to the "MUSIC" menu, and display of the CD/MP3/

Apple^®tracks and folders.

Open the "Telephone" menu

and display the list of recent

calls or accept an incoming call.

Long press: display the audio settings

screen for the radio tuner source.

Long press: display the audio settings screen for the

"MEDIA" (CD/USB/iPod/Streaming/AUX) sources.

Press and hold: reinitialise

the system.

Short press: select pre-set radio station.

Long press: pre-set the current station.

257

02 STEERING MOUNTED CONTROLS

RADIO: change to the next radio station in the list.

Long press: automatic search for a higher frequency.

CD: select the next track.

CD: press and hold: fast forward play.

SRC/TEL button:

change the audio source,

start a call from the address book,

call/end call on the telephone,

press for more than 2 seconds: open the

address book.

RADIO: change to the previous radio

station in the list.

Long press: automatic search for a

lower frequency.

CD: select the previous track.

CD: press and hold: fast reverse.

RADIO: select the previous/next preset

station.

Select the next entry in the address book.

Volume increase.

Mute: press the volume

increase and decrease

buttons simultaneously.

Restore the sound by

pressing one of the

two volume buttons.

Volume decrease.

258

03 GENERAL OPERATION

Press the MODE button several times in succession for access to the following displays:

"MAP IN WINDOW"

(If navigation guidance in

progress)

"RADIO"

"TELEPHONE"

(If conversation in progress)

"FULL SCREEN MAP"

Change the audio source:

SETUP: PARAMETERS

RADIO: RADIO broadcasts.

MUSIC: play MUSIC.

date and time, display conﬁguration, sound, vehicle

settings.

For cleaning the screen, the use of a soft, non-abrasive cloth

(spectacles cloth) is recommended, with no additional product.

For the details of the menus, refer to the "Screen menu map"

section.

259

GENERAL OPERATION

03

Display according to context

FULL SCREEN MAP OR IN

A NEW WINDOW:

TELEPHONE

A press on the knob gives access

to short-cut menus according to the

display in the screen.

(call in progress):

Stop / Restore guidance

1

Private mode

1

Select destination

1

RADIO:

Put call on hold

1

Enter an address

2

1

DTMF ring tones

Hang up

Change waveband

1

Directory

2

FM

2

GPS coordinates

2

DAB

AM

Divert route

1

MUSIC MEDIA PLAYERS,

CD or USB (according to

media):

Move the map

1

Service announcements

Info. on location

1

2

Play modes:

Trafﬁc anouncements (TA)

Select as destination

2

Normal

1

Information

Select as stage

2

Random

1

Entertainment

Special or Urgent

Save this place (contacts)

2

Random on all media

Quit map mode

1

2

Repetition

1

Guidance criteria

1

260

NAVIGATION - GUIDANCE

04

Access to the "NAVIGATION" menu

To make full use of all of the

functions of your navigation

system, update the mapping

regularly. Contact a

"Navigation - guidance"

PEUGEOT dealer or order

your mapping update at

Press NAV.

http://peugeot.navigation.com

List of recent destinations.

"Select destination"

"Journey leg and route"

"Guidance options"

"Map management"

"Stop / Restore guidance"

A short press on the end of the

lighting control stalk repeats

the last navigation message.

Go from the list to the menu (left/right).

To delete the list of recent destinations, select "Guidance

options" in the navigation menu then select "Delete last

destinations" and conﬁrm. Select "Yes" then conﬁrm.

Deleting just one destination is not possible.

or

261

04 NAVIGATION - GUIDANCE

Selecting a destination

Towards a new destination

Selection the town from the list offered,

then conﬁrm.

Press NAV to display the

"Navigation - guidance menu.

A pre-set list (by entering the ﬁrst few

letters) of the towns in the country selected

can be accessed directly by selecting and

conﬁrming "List" in the screen.

Select "Select destination" and

conﬁrm, then select "Enter an address"

and conﬁrm.

If possible, enter the "Road" and "N°/X"

information in the same way.

Select "Archive" to save the address entered in a contact ﬁle.

Select the "Country" function then

conﬁrm.

After about 60 seconds with no address entered, the system returns

to the last home page; to return to the current input, start again with

steps 1 and 2 then press again.

Select the "Town" or "Post code"

function then conﬁrm.

Conﬁrm "OK" to start guidance.

Select the guidance criteria: "Fastest

route", "Shortest route" or optimised

"Distance/Time", then select the

desired restriction criteria: "With tolls",

"With Ferry", or "Trafﬁc info" then

conﬁrm "OK".

Select the letters in the name of the

town or the characters in a post code

one at a time, conﬁrming each one with

the knob.

262

04 NAVIGATION - GUIDANCE

Towards a recent destination

Towards a contact in the directory of contacts

Press NAV to display the

"Navigation - guidance" menu.

Navigation towards a contact is only possible if there is an address

entered in the audio navigation system.

Select the desired destination and

conﬁrm to start navigation.

Press NAV to display the

"Navigation - guidance" menu.

Delete recent destinations

Select "Select destination" and

conﬁrm, then select "Directory" and

conﬁrm.

Press NAV to display the

"Navigation - guidance" menu.

Selection the desired destination from

your contacts and conﬁrm "OK" to start

navigation.

Select "Options" and conﬁrm and then

"Delete recent destinations" and

conﬁrm.

263

04 NAVIGATION - GUIDANCE

Towards GPS coordinates

Towards a point on the map

With the map displayed, press OK to

Press NAV to display the

"Navigation - guidance" menu.

display the contextual menu. Select

"Move the map" and conﬁrm.

Select "Select destination" and

conﬁrm, then select "GPS coordinates"

and conﬁrm.

Move the cursor using the control to

identify the desired destination.

Press OK to display the contextual

menu for "Move the map" mode.

Enter the GPS coordinates and

conﬁrm "OK" to start navigation.

Select "Select as destination" or

"Select as stage" and conﬁrm.

264

04 NAVIGATION - GUIDANCE

The points of interest (POI) indicate all of the service locations in the vicinity

(hotels, various businesses, airports...).

Towards points of interest (POI)

Select "Search by Name" to search for POIs by name and not by

proximity.

Press NAV to display the

"Navigation - guidance" menu.

Select the "Enter an address" function

and conﬁrm, then select Select

destination and conﬁrm.

Search for POIs in the categories

suggested in the following pages.

To select a POI close to your current

location, select "POI" and conﬁrm, then

select "Around the current place" and

conﬁrm.

Select the POI and conﬁrm "OK" to start

navigation.

To select a POI as a stage on the route,

select "POI" and conﬁrm, then select "On

the route" and conﬁrm.

To select a POI as a destination, ﬁrst

enter the country and town (refer to the

"Towards a new destination" section),

select "POI" and conﬁrm, ﬁnally select

"Near" and conﬁrm.

265

This icon appears when several POIs are grouped

together in the same area. Zooming in on this icon

shows details of the POIs.

04 NAVIGATION - GUIDANCE

List of principal points of interest (POI)

Airport

Service station

Cinema

Railway station

Bus station

Port

Garage

Theme parks

PEUGEOT

Hospital, Chemist,

Vet

Covered car park

Police station

Car park

Industrial estate

Supermarket

School

Rest area

Town hall

Post ofﬁce

Hotel

Vending machine

Restaurant

Cafeteria

Sports complex, sports centre,

sports ground

Museum, Culture, Theatre,

Historic monument

Swimming pool

Tourist information, Tourist

attraction

Bed and breakfast

Winter sports resort

Risk areas / Danger

areas*

*

According to availability in the country.

An annual mapping update allows new points of interest to be presented to you.

You can also update the Risk areas / Danger areas every month.

The detailed procedure is available on:

http://peugeot.navigation.com.

266

04 NAVIGATION - GUIDANCE

Settings for risk area / danger area alerts

These functions are only available if risk areas have been

downloaded and installed on the system.

The detailed procedure for updating risk area POIs can be found at

http://peugeot.navigation.com.

Press NAV to display the "Navigation -

guidance" menu.

Select "Guidance options" and conﬁrm,

then select "Set parameters for risk

areas" and conﬁrm.

Select:

-

"Visual alert"

"Audible alert"

"Alert only in guidance"

"Overspeed alarm only".

The choice of time of notiﬁcation deﬁnes

how long in advance that Risk area

warnings are given.

Select "OK" to conﬁrm the screen.

267

04 NAVIGATION - GUIDANCE

Adding a stage

Organising stages

To organise stages, carry out

Press NAV to display the

"Navigation - guidance" menu.

operations 1 to 2 again, then select

"Order/delete journey legs" and

conﬁrm.

Select the stage that you want to move

in the order.

Select "Journey leg and route" then

conﬁrm.

Select "Add a stage" then conﬁrm

Select and conﬁrm to save

the modiﬁcations.

The address of the stage is entered as

a destination, by "Enter an address",

a contact in "Directory", or "Previous

destinations".

Select "Delete" to delete the stage.

Select "Close to" a route passing

close to the stage or "Strict" for a route

passing through the stage.

Conﬁrm "OK" to start the guidance, and

give a general indication of the guidance

route.

268

04 NAVIGATION - GUIDANCE

Route options

Calculation criteria

Select "Deﬁne calculation criteria" and

conﬁrm.

This function allows modiﬁcation of:

-

the guidance criteria: ("Fastest

route", "Shortest route",

"Distance/Time"),

Press NAV to display the

"Navigation - guidance" menu.

-

the exclusion criteria: ("With tolls"

or "With Ferry"),

-

trafﬁc avoidance: ("Trafﬁc info").

If trafﬁc avoidance (Trafﬁc info) is selected, the system suggests

an alternative route if there is a delay on the guidance route.

Select "Guidance options" and conﬁrm.

Select "OK" and conﬁrm to save

the modiﬁcations.

269

04 NAVIGATION - GUIDANCE

Map management

Selecting the points of interest displayed on the map

Select from the various categories the

ones that you want to display on the

screen.

Press NAV to display the

"Navigation - guidance" menu.

Select "Default" to have only "Filling stations, garages" and

"Risk areas" appear on the map (if installed in the system).

Select "Map management" and conﬁrm.

Select "OK" then conﬁrm and

select "OK" again then conﬁrm to save

the modiﬁcations.

Select "Map details" and conﬁrm.

270

04 NAVIGATION - GUIDANCE

Map orientation

Select:

-

"Vehicle direction" to have the map

follow the direction of travel,

Press NAV to display the

"Navigation - guidance" menu.

"North direction" to keep the map

always North up,

"Perspective view" to display a

perspective view.

The colour of the map, different from the day and night mode, is

conﬁgured in the "SETUP" menu.

Select "Map management" and conﬁrm.

Street names are visible on the map from the 100 m scale.

Select "Map orientation" and conﬁrm.

271

04 NAVIGATION - GUIDANCE

Navigation voice synthesis

Adjusting the volume / Deactivation

The volume of messages can be adjusted during the transmission

of the message using the volume adjustment control.

Select the volume graph and conﬁrm.

The volume setting of guidance messages is also accessible via

the "SETUP" / "Voice synthesis" menu.

Adjust the volume to the desired level

and conﬁrm.

Press NAV to display the

"Navigation - guidance" menu.

Select "Deactivate" to deactivate voice messages.

Select "Guidance options" and conﬁrm.

Select "OK" and press the dial

to conﬁrm.

Select "Set speech synthesis" and

conﬁrm.

272

04 NAVIGATION - GUIDANCE

Male voice / Female voice

Press SETUP to display the

conﬁguration menu.

Select "Voice synthesis" and conﬁrm.

Select "Select male voice" or "Select

female voice" then conﬁrm "Yes" to

activate a male or female voice. The

system restarts.

273

TRAFFIC INFORMATION

05

Access to the "TRAFFIC INFORMATION" menu

"Trafﬁc information"

Press "TRAFFIC".

"Geographic ﬁlter"

"Select TMC station"

(automatic, manual)

List of TMC messages in order

of distance from the vehicle.

"Display/Do not display

messages"

Go from the list to the menu (left/right).

or

274

05 TRAFFIC INFORMATION

Configure the filtering and display of TMC messages

TMC (Trafﬁc Message Channel) messages with GPS Navigation provide trafﬁc information in real time.

The system offers a choice of:

-

"Retain all the messages",

Press the TRAFFIC button to display the

"Trafﬁc information" menu.

or

-

"Retain the messages"

● "Around the vehicle", (conﬁrm

the mileage to modify and select

the distance),

● "On the route".

Select the "Geographic ﬁlter" function

and conﬁrm.

Conﬁrm "OK" to save the modiﬁcations.

We recommend:

-

a ﬁlter on the route and

a ﬁlter around the vehicle of:

-

12 miles (20 km) in urban areas,

30 miles (50 km) on motorways.

275

05 TRAFFIC INFORMATION

Principal TMC symbols

Receiving TA messages

The TA (Trafﬁc Announcement) function gives priority to TA alert

messages. To operate, this function needs good reception of a

radio station transmitting this type of message. When a trafﬁc report

is transmitted, the current audio source (Radio, CD, USB, ...) is

interrupted automatically to play the TA message. Normal playback

of the audio source resumes at the end of the transmission of

the message.

Black and blue triangle: general information, for example:

Weather reports

Wind

Trafﬁc reports

Fog

Parking

Snow / ice

Press RADIO to display the menu.

Red and yellow triangle: trafﬁc information, for example:

Select "Service announcements" then

conﬁrm.

Modiﬁed signage

Slippery surface

Delay

Narrow carriageway

Accident

Activate or deactivate "TA" then conﬁrm.

Roadworks

Road closed

Danger

Risk of explosion

Demonstration

No entry

The volume setting for TA messages can be adjusted only during the

transmission of this type of alert.

Activate or deactivate the function at any time by pressing

the button.

Trafﬁc jam

During a message, press the button to interrupt it.

276

USING THE TELEPHONE

06

Access to the "TELEPHONE" menu

In the top bar of the permanent

display

"Telephone"

No telephone connected.

Telephone connected.

Incoming call.

Press this button.

List of recent calls sent and

received with the telephone

connected to the system.

"Dial"

"Directory of contacts"

"ontacts management"

"Phone functions"

"Bluetooth functions"

"Hang up"

Outgoing call.

Synchronisation of

contacts in progress.

Telephone call in

progress.

Go from the list to the menu (left/right).

To make a call, select a number in the list and conﬁrm "OK"

to start the call.

or

Connecting a different telephone deletes the list of

recent calls.

277

06 USING THE TELEPHONE

For reasons of safety and because they require prolonged attention

on the part of the driver, the operations for pairing the Bluetooth

mobile telephone to the hands-free system of the audio unit must be

carried out with the vehicle stationary.

Pairing a Bluetooth^®telephone

First connection

You can check the compatibility of your telephone at

www.peugeot.co.uk (services).

Procedure from the system

Quick procedure from the telephone

Activate the telephone's Bluetooth function

and ensure that it is "visible to all" (telephone

conﬁguration).

In the Bluetooth menu of your telephone, select the

name "PEUGEOT" from the list of devices detected.

Press this button.

Enter a minimum 4 ﬁgure code in the telephone and

conﬁrm.

Select "Bluetooth functions" and

conﬁrm.

Select "Peripherals search" and

conﬁrm.

Enter the same code in the system,

select "OK" and conﬁrm.

The list of peripheral devices detected

is displayed. Wait until the "Connect"

button is available.

278

06 USING THE TELEPHONE

The services available depend on the network, the SIM card and the compatibility of the Bluetooth telephone used. Check the telephone

manual and with your network provider for details of the services available to you.

Select the name of the desired

Enter a minimum 4 ﬁgure code in the telephone

and conﬁrm.

peripheral from the list of devices

detected then conﬁrm.

Select "Connect" and conﬁrm.

Enter the same code in the system,

select "OK" and conﬁrm.

The system offers to connect the

telephone:

Then accept automatic connection on the telephone to allow the

telephone to reconnect automatically every time the vehicle is

started.

-

in "Hands-free mode" (telephone

only),

in "Audio" mode (streaming: playing

music ﬁles on the telephone),

or "All" (for selection of both

modes).

Depending on the type of telephone, the system will ask you to

accept or not the transfer of your contacts.

Select "OK" and conﬁrm.

The "Hands-free mode" should be used in preference if

"Streaming" is not desired.

On return to the vehicle, the last telephone connected

automatically reconnects, within around 30 seconds after

switching on the ignition (Bluetooth activated and visible).

To modify the automatic connection mode, remove the pairing

and pair the telephone again with the desired mode.

The ability of the system to connect in only one mode depends on

the telephone. The two modes may both connect by default.

279

06 USING THE TELEPHONE

Directory configuration / Synchronisation with the telephone

Select "Import all the entries" to import

all the contacts in the telephone and

save them in the system.

Once imported, a contact remains visible

whatever telephone is connected.

Press PHONE then select "Contacts

management" and conﬁrm.

Select "Synchronization options":

Select "New contact" to enter a new

contact.

-

No synchronization: only the

contacts saved in the system

(always present).

-

Display telephone contacts: only the

contacts saved in the telephone.

Display SIM card contacts: only the

contacts saved on the SIM card.

Display all phone contacts:

contacts on the SIM card and in the

telephone.

Select "Sort by Name/First name" or

"Sort by First name/Name" to choose

the order in which they appear.

Select "Contact mem. status" to see the

number of contacts saved in the system

or imported, and the free memory.

Select "Delete all contacts" to delete

the contacts saved in the system.

280

06 USING THE TELEPHONE

Editing, importing or deleting a contact

Press PHONE then select "Directory of

contacts" and conﬁrm.

It is not possible to modify or delete contacts in the telephone or the

SIM card via the Bluetooth connection.

Select "Search", then turn the knob to

choose in numerical or alphabetical order

a group of contacts from the entries made

previously, then conﬁrm.

Once the contact has been imported, the Bluetooth symbol

disappears, replaced by the telephone symbol which shows that the

contact has been saved in the system.

Go to the list of contacts, select the

desired contact then conﬁrm.

In the "Directory of contacts" menu, the import and deletion of

contacts is done one by one.

Select "Open" to view a contact on the

telephone or modify a contact saved in

the system.

Select "Import" to copy a contact from

the telephone to the system.

Select OK or press the back button to exit

this menu.

Select "Delete" to delete a contact

recorded in the system.

281

06 USING THE TELEPHONE

Using the telephone is not recommended while driving. We

recommended that you park safely or make use of the steering

mounted controls.

Making a call

Calling a contact

Calling a new number

Press TEL or twice on PHONE.

Press PHONE twice.

Select "Directory of contacts" then

conﬁrm.

Select "Dial" then conﬁrm.

Select the desired contact and conﬁrm.

If access was via the PHONE button,

select "Call" and conﬁrm.

Dial the telephone number using the

virtual keypad selecting each number

in turn.

Select the number and conﬁrm to start

the call.

Conﬁrm "OK" to make the call.

282

06 USING THE TELEPHONE

Ending a call

Calling a recently entered number

Press PHONE then select "OK" to end

the call.

Press TEL, select "Call list" and

conﬁrm,

or

Or make a long press on TEL at the

steering mounted controls.

Press PHONE to display the calls log.

Or make two short presses on TEL at

the steering mounted controls.

Select the desired number and conﬁrm.

Or press the MODE button, as many

times as necessary, until the telephone

screen is displayed.

To erase the calls log, press PHONE twice, select "Phone

functions" and conﬁrm then select "Delete calls log" and conﬁrm.

Press "OK" to display the contextual

menu then select "Hang up" and

conﬁrm.

It is always possible to start a call directly from the telephone; park

the vehicle as a safety measure.

283

06 USING THE TELEPHONE

Receiving a call

An incoming call is announced by a ring and a superimposed display

on the screen.

"Yes" to accept the call is selected by

default.

Press "OK" to accept the call.

Select "No" and conﬁrm to reject the

call.

A short press on TEL accepts an

incoming call.

A long press on TEL rejects an incoming

call.

284

06 USING THE TELEPHONE

Options during a call*

Select "DTMF ring tones" to use the

numerical keypad, so as to navigate

through the menu of an interactive vocal

server.

During a call, press the MODE button

several times to select display of the

telephone screen, then press "OK" to

open the contextual menu.

Select "Hang up" to end the call.

Or make a short press on this button.

Select "Private mode" and conﬁrm to

it is possible to hold a 3-way conference

call by making 2 calls in succession*.

Select "Conference mode call" in the

contextual menu accessible using this

button.

take the call on the handset.

Or select "Hands-free mode" and

conﬁrm to take the call via the vehicle's

speakers.

Select "Put call on hold" and conﬁrm to

put the current call on hold.

Or select "Resume the call" and

conﬁrm to resume the call on hold.

* Depending on the compatibility of the phone and your service plan.

285

06 USING THE TELEPHONE

Managing paired telephones

Changing the ringtone

Press PHONE twice.

Select "Phone functions" and conﬁrm.

Select "Bluetooth functions".

Select "Ring options" and conﬁrm.

Select "List of the paired peripherals"

and conﬁrm.

You can adjust the volume and the type

of ringtone.

It is possible to:

-

"Connect" or "Disconnect" the

selected telephone,

-

delete the pairing of the selected

telephone.

Select "OK" and conﬁrm to save

the changes.

It is also possible to select all pairings.

286

RADIO

07

Access to the "RADIO" menu

"FM / DAB / AM"

Press RADIO.

Alphabetical list of stations

received.

"Change waveband"

("FM / DAB / AM")

"Options" ("TA, RDS, DAB/FM

station tracking")

"Audio settings" (see this

section)

"Update radio list"

Go from the list to the menu (left/right).

Press 5 or 6 or use the rotary control to select the

previous or next station in the list.

or

287

07 RADIO

Changing waveband

Selecting a station

The external environment (hill, building, tunnel, underground car park...) may interfere with the reception, including in RDS station tracking mode.

This phenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a fault with the audio system.

The quality of reception is represented by the number of

active waves in this symbol.

By alphabetical list

Press RADIO, select the station of your

choice and conﬁrm.

Press RADIO or OK to display the

contextual menu.

By automatic frequency search

Press 7 or 8 for the automatic search

for a lower or higher radio frequency.

Select "Change waveband".

Or turn the thumb wheel at the steering

mounted controls.

By manual frequency search

Select "FM / DAB / AM" and conﬁrm.

Press 5 or 6 to adjust the radio

frequency step by step.

288

07 RADIO

Presetting a station

Activate / Deactivate RDS

RDS, if activated, allows you to continue listening to the same

station by automatic retuning to alternative frequencies. However,

in certain conditions, coverage of an RDS station may not be

assured throughout the entire country as radio stations do not

cover 100 % of the territory. This explains the loss of reception of

the station during a journey.

Press RADIO.

After selecting a station, press one of the buttons on the

numerical keypad for 2 seconds to preset the current

station.

An audible signal conﬁrms that the station has been preset.

Select "Guidance options" then

conﬁrm.

Press the button on the numerical keypad to recall a

preset station.

Or press then turn the thumb wheel at the steering

mounted controls.

Activate or deactivate "RDS" then

conﬁrm.

289

07 RADIO

Display of the "DAB" or "DAB

(FM)" band.

Represents the signal strength

for the band being listened to.

Display of the name of

the current station.

Any thumbnail broadcast by the

station.

The "Video mode" allows the

display to be enlarged.

Preset stations, buttons 1 to 6

Short press: select the preset radio

station.

Long press: preset a radio station.

Display of "Radiotext" for the

current station.

Display of the name and number of

the multiplex service being used.

Display of options:

if active but not available, the display

will be greyed out,

if active and available, the display will

be empty.

If the "DAB" radio station being

listened to is not available on

"FM", the "DAB FM" option is

greyed out.

290

07 RADIO

DAB (Digital Audio Broadcasting)

Digital radio

Digital radio - DAB/FM auto tracking

Digital radio provides a higher quality reception and also the

graphical display of information for the radio station, by selecting

"Video mode" in "Radio favourites" (Options).

The different radio multiplex services offer a choice of stations

displayed in alphabetical order.

"DAB" does not have 100% coverage of the country.

When the digital signal is weak, "DAB / FM auto tracking" allows you

to continue listening to the same station, by automatically switching

to the corresponding analogue "FM" station (if one exists).

Press "RADIO".

Select "Options" and conﬁrm.

Select "Change band" and conﬁrm.

Selection "DAB" and conﬁrm.

Select "FM/DAB" and conﬁrm.

If "DAB / FM auto tracking" is on, there will be a difference of a few

seconds in the programme when the system changes to analogue

"FM" radio with sometimes a variation in volume.

Display of the "DAB" band then becomes "DAB (FM)".

When the strength of the digital signal is good again, the system

automatically switches back to "DAB".

Change of station in the same "multiplex".

Manual search for a "multiplex".

If the "DAB" station you are listening to is not available on "FM"

("DAB/FM" option greyed out), or if "DAB / FM auto tracking" is not

on, the sound will be cut when the digital signal is too weak.

291

MUSIC MEDIA PLAYERS

08

Access to the "Music media player" menu

"MEDIA"

Press MUSIC.

List of the current media

tracks.

"Change media"

"Eject USB device" (if USB

connected)

"Play mode" ("Normal",

"Random", "Random on all

media", "Repetition")

"Audio settings"

"Activate / Deactivate AUX input"

Go from the list to the menu (left/right).

or

292

08 MUSIC MEDIA PLAYERS

CD, MP3 CD / USB player

Information and advice

The audio equipment will only play audio ﬁles with ".wma, .aac, .ﬂac,

.ogg and .mp3" ﬁle extensions and with a bit rate of between 32 Kbps

and 320 Kbps.

It also supports VBR (Variable Bit Rate) mode.

No other type of ﬁle (.mp4, .m3u...) can be played.

WMA ﬁles must be of the standard wma 9 type.

The sampling rates supported are greater than 32 KHz.

The system supports USB mass storage or iPod

devices via the USB port (suitable cable not supplied).

If a partitioned USB memory key is connected to the

system, only the ﬁrst partition is recognised.

Control of the peripheral device is with the audio

system controls.

The number of tracks is limited to 2000 maximum,

999 tracks per folder.

If the current consumption at the USB port exceeds

500 mA, the system goes into protection mode and

deactivates the port.

Other peripherals, not recognised on connection, must

be connected to the auxiliary socket using a Jack cable

(not supplied).

It is advisable to restrict ﬁle names to 20 characters, without using of

special characters (e.g.: " " ? ; ù) to avoid any playing and displaying

problems.

Use only USB memory sticks formatted FAT32 (File Allocation Table).

In order to be able to play a recorded CDR or CDRW, when recording

it is preferable to select the ISO 9660 level 1, 2 or Joliet standard.

If the disc is recorded in another format (udf, ...), it may not be played

correctly.

It is recommended that the same recording standard is always used

for an individual disc, with as low a speed as possible (4x maximum)

for optimum sound quality.

The system does not support the operation of an Apple^®player and a

USB memory stick connected at the same time.

In the particular case of a multi-session CD, the Joliet standard is

recommended.

It is recommended that ofﬁcial Apple^®USB cables are used to ensure

correct operation.

293

08 MUSIC MEDIA PLAYERS

Sources

Selection of source

The SOURCE button on the steering mounted controls allows a

direct change to the next media source.

Insert the CD in the player, insert the USB

memory stick in the USB player or connect the

USB peripheral to the USB port using a suitable

cable (not supplied).

"CD / CD MP3"

The system builds playlists (in temporary

memory), an operation which can take from

a few seconds to several minutes at the ﬁrst

connection.

"USB, iPod"

"RADIO"

Reduce the number of non-music ﬁles and the

number of folders to reduce the waiting time.

"STREAMING"

"AUX"

The playlists are updated every time the ignition

is switched off or connection of a USB memory

stick. However, the system memorises these

lists and if they are not modiﬁed, the loading

time will be shorter.

Play starts automatically after a period which

depends on the capacity of the USB memory

stick.

Press MUSIC to display the "MEDIA"

menu.

Select "Following media source" and

conﬁrm.

Repeat the operation as many times as necessary to obtain the

desired media source (except for radio which is accessible either

with SOURCE or RADIO).

294

08 MUSIC MEDIA PLAYERS

Selecting a track

MUSIC: List of USB or CD tracks or

folders

Previous track.

/

Next track.

Up or down in the list.

/

Previous folder.

Conﬁrm, next menu level.

/

Next folder.

Fast forward.

Fast backward.

Long press

/

+

/

Up one menu level.

/

Pause: long press on SRC.

295

08 MUSIC MEDIA PLAYERS

Connecting APPLE^®players

Audio streaming

Connect the Apple^®player to the USB port using a suitable cable

(not supplied).

Play starts automatically.

Streaming allows audio ﬁles on your telephone to be played via the

vehicle's speakers.

Control is via the audio system.

Connect the telephone: refer to the "USING THE TELEPHONE" section.

Select "Audio" or "All" proﬁle.

The classiﬁcations available are those of the portable device

connected (artists / albums / genres / playlists / audiobooks /

podcasts).

The default classiﬁcation used is by artist. To modify the classiﬁcation

used, return to the ﬁrst level of the menu then select the desired

classiﬁcation (playlists for example) and conﬁrm to go down through

the menu to the desired track.

If play does not start automatically, it may be necessary to start the

audio playback from the telephone.

Control is from the peripheral device or by using the audio system

buttons.

The "Shufﬂe tracks" mode on an iPod^®corresponds to the "Random"

mode on the audio system.

The "Shufﬂe albums" mode on an iPod^®corresponds to the "Random

all" on the audio system.

"Shufﬂe tracks" is restored by default on each connection.

Once connected in streaming mode, the telephone is considered to be

a media source.

It is recommended that you activate "Repeat" on the Bluetooth

peripheral.

The version of software in the audio system may not be compatible

with the generation of your Apple^®player.

296

08 MUSIC MEDIA PLAYERS

Using the auxiliary input (AUX)

JACK/USB audio cable not supplied

Select "Activate / Deactivate AUX

input" and conﬁrm.

First adjust the volume of your portable

device (to a high level). Then adjust the

volume of your audio system.

Connect the portable device

(MP3, WMA player…) to the

JACK auxiliary audio socket or

USB port using a suitable cable.

Press MUSIC to display the "MUSIC"

menu.

Display and management of the controls are via the portable device.

297

09 AUDIO SETTINGS

They are accessible by the MUSIC

button in the control panel or by a long

press on RADIO according to the source

in use.

The audio settings (Equalizer, Bass, Treble and Loudness) are

different and independent for each sound source.

The settings for distribution and balance are common to all sources.

-

"Equalizer" (choice of 6 musical ambiences)

"Bass"

"Treble"

"Loudness" (Activate/Deactivate)

"Distribution" ("Driver", "All passengers")

"Le-Ri balance" (Left/Right)

"Fr-Re balance" (Front/Rear)

"Auto. Volume" depending on road speed (Activate/Deactivate)

On-board audio: Arkamys^©Sound Staging optimises sound distribution

in the the passenger compartment.

The distribution (or spatialisation using the Arkamys^©system) of sound

is an audio process that allows the audio quality to be adapted to the

number of listeners in the vehicle.

298

10 CONFIGURATION

Display configuration

Select "Choose colour" and conﬁrm to

select the screen colour harmony and

the map presentation mode:

-

day mode,

night mode,

automatic day/night mode,

according to whether the

headlamps are on.

Press SETUP to display the

"Conﬁguration" menu.

Select "Adjust luminosity" and conﬁrm

to adjust the screen brightness.

Press "OK" to save the changes.

The settings for day and night are

independent.

Select "Display conﬁguration" and

conﬁrm.

299

11 SCREEN MENU MAP(S)

Previous destinations

Map management

MAIN FUNCTION

1

3

Map orientation

Order/delete journey legs

2

Option A

1

Vehicle direction

Divert route

3

2

Option A1

2

Chosen destination

North direction

2

3

Option A11

3

Perspective view

Guidance options

1

Option B...

1

Deﬁne calculation criteria

Map details

2

"Navigation - guidance"

Fastest route

Move the map

3

2

MENU

Shortest route

Mapping and updating

Description of risk areas database

3

Distance/Time

Select destination

3

1

Enter an address

With tolls

With Ferry

Trafﬁc info

2

Stop / Restore guidance

1

Directory

With Ferry

3

Trafﬁc info

300

11 SCREEN MENU MAP(S)

Call

Contact mem. status

2

"TRAFFIC INFORMATION"

MENU

Open

Phone functions

2

1

Geographic filter

Import

Search

Delete

Cancel

Ring options

1

2

Retain all the messages

Retain the messages

Around the vehicle

On the route

Delete calls log

2

Bluetooth functions

1

List of the paired peripherals

3

2

Connect

Contacts management

3

1

New contact

Select TMC station

Disconnect

1

2

Automatic TMC

Delete

Sort by First name/Name

Delete all contacts

2

Manual TMC

Delete all

List of TMC stations

Cancel

Import all the entries

Synchronization options

No synchronization

Peripherals search

Rename radiotelephone

Display / Do not display

messages

1

2

3

"TELEPHONE" MENU

Hang up

Display telephone contacts

Display SIM card contacts

Display all phone contacts

1

3

Dial

1

Directory of contacts

1

301

11 SCREEN MENU MAP(S)

Bass

"RADIO" MENU

"MUSIC" MENU

2

Treble

Change Waveband

1

Change Media

1

Loudness

FM

2

CD

2

Activated / Deactivated

Distribution

DAB

AM

3

Bluetooth streaming

2

USB/iPod

2

Driver

Options

3

1

AUX

2

All passengers

Le-Ri balance

Fr-Re balance

Auto. Volume

Activated / Deactivated

RDS station tracking

2

Read mode

1

FM/DAB

2

Normal

2

Audio settings

1

Random

2

Equalizer

2

Random on all media

2

None

3

Repetition

2

Classical

Jazz

Update radio list

1

3

Audio settings

1

Activate / Deactivate AUX

input

1

Rock

Techno

Vocal

302

11 SCREEN MENU MAP(S)

"SETUP" MENU

Select language

Define vehicle parameters*

1

Français

Trip computer

2

Display configuration

1

English

Alert log

2

Choose colour

2

Italiano

Status of functions

Harmony

3

Portuguese

Español

Deutsch

Nederlands

Turkçe

Cartography

Day mode

4

Night mode

4

Auto Day/Night

Adjust luminosity

Set date and time

Select units

2

Polski

Русский

Cestina

Speech synthesis setting

1

Hrvatski

Hungarian

Guidance instructions volume

2

Select male voice/Select female voice

* The settings vary according to the vehicle.

303

FREQUENTLY ASKED QUESTIONS

The following table groups together the answers to the most frequently asked questions concerning your audio system.

QUESTION

ANSWER

SOLUTION

The route calculation is

not successful.

The guidance criteria may conﬂict with the current location (exclusion of

toll roads on a toll motorway).

Check the guidance criteria on the Navigation

Menu, "Guidance options"\ "Deﬁne calculation

criteria".

I am unable to enter my

post code.

The system only accepts post codes of up to 7 characters.

The POIs have not been selected.

The POIs do not appear.

Select the POIs in the list of POIs.

The risk areas audible

warning does not work.

The audible warning is not active.

Activate audible warnings in the Guidance options

menu, "Navigation - guidance", "Set parameters for

risk areas".

The system does not

suggest a detour around

an incident on the route.

The guidance criteria do not take account of TMC messages.

Select the "Trafﬁc info" function in the list of

guidance criteria.

I receive a Risk area alert Other than guidance, the system announces all Risk areas positioned in a Zoom in on the map to view the exact position of

which is not on my route. cone located in front of the vehicle. It may provide an alert for a Risk area the Risk area. Select "On the route" to no longer

located on nearby or parallel roads.

receive alerts other than guidance or to reduce the

time for the announcement.

304

FREQUENTLY ASKED QUESTIONS

QUESTION

ANSWER

SOLUTION

Certain trafﬁc jams along On starting, it is several minutes before the system begins to receive the

Wait until the trafﬁc information is being received

correctly (display of the trafﬁc information icons on

the map).

the route are not indicated trafﬁc information.

in real time.

The ﬁlters are too restrictive.

Modify the "Geographic ﬁlter" settings.

In certain countries, only major routes (motorways...) are listed for the

trafﬁc information.

This phenomenon is normal. The system is

dependent on the trafﬁc information available.

The altitude is not

displayed.

On starting, the initialisation of the GPS may take up to 3 minutes to

receive more than 4 satellites correctly.

Wait until the system has started up completely.

Check that there is a GPS coverage of at least

4 satellites (long press on the SETUP button, then

select "GPS coverage").

Depending on the geographical environment (tunnel...) or the weather, the This phenomenon is normal. The system is

conditions of reception of the GPS signal may vary.

dependent on the GPS signal reception conditions.

I am unable to connect

my Bluetooth telephone.

The telephone's Bluetooth function may be switched off or the telephone

may not be visible.

-

Check that your telephone's Bluetooth function

is switched on.

Check in the telephone settings that it is

"visible to all".

The Bluetooth telephone is not compatible with the system.

The volume depends both on the system and on the telephone.

You can check the compatibility of your telephone

on www.peugeot.co.uk (services)

The volume of the

telephone connected

in Bluetooth mode is

inaudible.

Increase the volume of the audio system, to

maximum if required, and increase the volume of

the telephone if necessary.

The ambient noise level has an inﬂuence on the quality of telephone

communication.

Reduce the ambient noise level (close the windows,

reduce the booster fan speed, slow down, ...).

305

FREQUENTLY ASKED QUESTIONS

QUESTION

ANSWER

SOLUTION

Some contacts are

duplicated in the list.

The options for synchronizing contacts are synchronizing the contacts

on the SIM card, the contacts on the telephone, or both. When both

synchronizations are selected, some contacts may be duplicated.

Select "Display SIM card contacts" or "Display

telephone contacts".

Contacts are not shown in Some telephones offer display options. Depending on the settings chosen, Modify the display setting in the telephone

alphabetical order.

contacts can be transferred in a speciﬁc order.

directory.

The system does not

The Bluetooth mode does not permit sending SMS text messages to the

receive SMS text messages. system.

The CD is ejected

automatically or is not

played by the player.

The CD is inserted upside down, is unplayable, does not contain any

-

Check that the CD is inserted in the player the

audio data or contains an audio format which the player cannot play.

right way up.

Check the condition of the CD: the CD cannot

be played if it is too damaged.

Check the content in the case of a recorded

CD: refer to the information and advice in the

"MUSIC MEDIA PLAYERS" section.

The CD has been recorded in a format that is not compatible with the

player (udf, ...).

The CD is protected by an anti-pirating protection system which is not

recognised by the audio system.

-

The audio system's CD player does not play

DVDs.

Some recorded CDs will not be played by the audio

system because they are not of the correct quality.

There is a long waiting

When a new medium is inserted, the system reads a certain amount of

This phenomenon is normal.

period following the insertion data (directory, title, artist, etc.). This may take from a few seconds to a

of a CD or connection of a

USB memory stick.

few minutes.

The CD player sound is

poor.

The CD used is scratched or of poor quality.

Insert good quality CDs and store them in suitable

conditions.

The audio equipment settings (bass, treble, ambiences) are unsuitable.

Set the treble or bass level to 0, without selecting

an ambience.

306

FREQUENTLY ASKED QUESTIONS

QUESTION

ANSWER

SOLUTION

Some characters in the

media information are not

displayed correctly while

playing.

The audio system does not read some types of characters.

Use standard characters to name tracks and

folders.

Playing of streaming ﬁles The peripheral device connected does not support automatic play.

does not start.

Start the playback from the device.

The names of tracks and The Bluetooth proﬁle does not allow the transfer of this information.

the track length are not

displayed on the screen

when streaming audio.

The quality of reception of The vehicle is too far from the transmitter used by the station listened to or Activate the "RDS" function by means of the

the radio station listened

to gradually deteriorates

or the stored stations do

not function (no sound,

87.5 Mhz is displayed...).

there is no transmitter in the geographical area through which the vehicle short-cut menu to enable the system to check

is travelling.

whether there is a more powerful transmitter in the

geographical area.

The environment (hills, buildings, tunnels, basement car parks...) block

reception, including in RDS mode.

This phenomenon is normal and does not indicate

a fault with the audio system.

The aerial is absent or has been damaged (for example when going

through an automatic car wash or in an underground car park).

Have the aerial checked by a PEUGEOT dealer.

I cannot ﬁnd some radio

stations in the list of

stations received.

The station is not received or its name has changed in the list.

Some radio stations send other information in place of their name (the title

of the song for example).

The system interprets this information as the name of the station.

The name of the radio

station changes.

307

FREQUENTLY ASKED QUESTIONS

QUESTION

ANSWER

SOLUTION

When modifying the

treble and bass setting,

the choice of ambience is

cancelled.

The selection of an ambience imposes speciﬁc treble and bass settings.

Modify the treble and bass settings or choose a

musical ambience to obtain the desired sound

quality.

When modifying the

ambience, the treble

and bass settings are

cancelled.

When modifying the

balance settings,

the "Driver" or "All

passengers" setting is

cancelled.

The choice of the "Driver" distribution setting imposes speciﬁc balance

settings.

When modifying

the "Driver" or "All

passengers" distribution

setting, the balance

settings are cancelled.

There is a difference in

For optimum sound quality, the audio settings for Volume, Bass, Treble,

Check that the audio settings for (Volume, Bass,

Treble, Equalizer, Loudness) are adapted to

the sources listened to. It is advisable to set the

AUDIO functions (Bass, Treble, Fr-Re balance,

Le-Ri balance) to the middle position, select the

"None", musical ambience and set the loudness

correction to the "Active" position in CD mode or to

the "Inactive" position in radio mode.

sound quality between the Equalizer and Loudness can be adapted to the different sound sources,

different audio sources

(radio, CD...).

which may result in audible differences when changing source (radio,

CD...).

308

FREQUENTLY ASKED QUESTIONS

QUESTION

ANSWER

SOLUTION

With the engine off, the

When the engine is switched off, the system's operating time depends on Start the vehicle's engine to increase the battery

system switches off after the state of charge of the battery.

a few minutes of use.

charge.

The switch-off is normal: economy mode is activated automatically to

maintain the state of charge of the vehicle's battery, needed for engine

starting. (See the "Energy economy mode" section).

Playback of my USB

memory stick starts only

after a very long wait

(around 2 to 3 minutes).

Some ﬁles supplied with the memory stick may greatly slow down access Delete the ﬁles supplied with the memory stick and

to reading the memory stick (multiplication by 10 of the catalogue time).

limit the number of sub-folders in the ﬁle structure

on the memory stick.

When I connect my

When the iPhone connects automatically as a telephone, it forces the

Disconnect and reconnect to the USB port

(the USB function takes priority over streaming).

iPhone as telephone and streaming function. The streaming function takes the place of the USB

to the USB port at the

function which is then not useable, there is a period without sound of the

same time, I am unable to track being played with Apple^®players.

play the music ﬁles.

309

310

PEUGEOT Connect Sound (RD5)

Audio system / Bluetooth^®

CONTENTS

Your PEUGEOT Connect Sound (RD5) is coded in such

a way that it will only operate in your vehicle.

p.

312

313

314

315

318

321

324

329

01 First steps

02 Steering mounted controls

03 Main menu

04 Audio

05 PEUGEOT Connect USB

06 Bluetooth

07 Screen menu map(s)

Frequently asked questions

For safety reasons, the driver must only carry out

operations which require prolonged attention while the

vehicle is stationary.

When the engine is switched off and to prevent

discharging of the battery, the audio equipment may

switch off after a few minutes.

311

01 FIRST STEPS

Display the list of

local stations.

Long press: CD

tracks or MP3

folders (CD / USB).

Audio settings: front/

rear fader, left/right

balance, bass/treble,

loudness, audio

Select source:

radio, audio CD / MP3 CD, USB,

Jack connection, Streaming,

AUX.

Select AM / FM

wavebands.

Abandon the current

operation.

ambiences.

TA (Trafﬁc Announcements)

on/off.

Long press: PTY* (radio

Programme TYpe) mode.

Eject CD.

Select the screen display

mode:

Automatic frequency search

down/up.

Date, audio functions, trip

computer, telephone.

Select previous/next CD, MP3

or USB track.

Conﬁrm.

On/off, volume setting.

The DARK button changes the screen display

for improved driving comfort at night.

Buttons 1 to 6:

Select a pre-set radio station.

Long press: pre-set a station.

Display main menu.

Select next frequency down/up.

Select previous/next MP3 folder.

Select previous/next folder / genre /

artist / playlist (USB).

1^stpress: upper bar only illuminated.

2^ndpress: black screen.

3^rdpress: return to standard display.

*

Available according to version.

312

02 STEERING MOUNTED CONTROLS

Radio: automatic search for a higher frequency.

CD / MP3 / USB: selection of the next track.

CD / USB: continuous press: fast forwards play.

Move in the list.

Change audio source.

Conﬁrm a selection.

Call/end call on the telephone.

Press for more than 2 seconds:

telephone main menu.

Radio: automatic search for a lower

frequency.

CD / MP3 / USB: selection of the

previous track.

CD / USB: continuous press: fast

reverse.

Move in the list.

Radio: select the previous/next pre-set

station.

USB: select genre / artist / folder from

the classiﬁcation list.

Select the previous/next item in a menu.

Volume increase.

Mute: press the volume

increase and decrease

buttons simultaneously.

The sound is restored

by pressing one of the

two volume buttons.

Volume decrease.

313

03 MAIN MENU

Audio functions

Trip computer

Radio; CD; USB; AUX.

Enter distances; Alerts; State of functions.

Screen C

Personalisation-conﬁguration

Bluetooth^®: Telephone - Audio

Vehicle parameters; Display; Languages.

Pairing; Hands-free kit; Streaming.

Screen A

For an overview of the menus

available, refer to the "Screen

menu map" section.

314

The external environment (hills, buildings, tunnels, basement car parks, ...)

may block reception, including in RDS mode. This is a normal effect of the

way in which radio waves are transmitted and does not indicate any failure

of the audio system.

04 AUDIO

Selecting a station

RDS

Press the SOURCE button several

times in succession and select

the radio.

Press the MENU button.

Select "Audio functions".

Press OK.

Press the BAND AST button

to select a waveband.

Select the "FM waveband

preferences" function.

Brieﬂy press one of the buttons to

carry out an automatic search of the

radio stations.

Press OK.

Select "Activate RDS".

Press one of the buttons to carry out

a manual search up / down for radio

frequencies.

Press OK, RDS is displayed in the

screen.

In "Radio" mode, press OK directly to activate / deactivate

RDS mode.

Press the LIST REFRESH button to

display the list of stations received

locally (30 stations maximum).

To update this list, press for more

than two seconds.

RDS, if displayed, enables you to continue listening to the same station

by automatic retuning to alternative frequencies. However, in certain

conditions, coverage of an RDS station may not be assured throughout

the country as radio stations do not cover 100 % of the territory. This

explains the loss of reception of a station that can occur during a journey.

315

04 AUDIO

Receiving TA messages

CD player

The TA (Trafﬁc Announcement) function gives priority to TA alert

messages. To operate, this function needs good reception of a

radio station transmitting this type of message. When a trafﬁc

report is transmitted, the current audio source (Radio, CD, ...) is

interrupted automatically to play the TA message. Normal playback

of the audio source resumes at the end of the transmission of the

message.

Insert circular compact discs only.

Some anti-pirating systems, on original discs or CDs copied using a

personal recorder, may cause faults which are no reﬂection on the

quality of the vehicle's player.

Insert a CD in the player, play begins automatically.

To play a disc which has already been

inserted, press the SOURCE button

several times in succession and

select CD.

Press the TA button to activate or

deactivate trafﬁc messages.

Press one of the buttons to select a

track on the CD.

Press the LIST REFRESH button to display the list of tracks on

the CD.

Press and hold one of the buttons for

fast forward or fast back.

316

04 AUDIO

Information and advice

Playing an MP3 CD compilation

Insert an MP3 CD compilation in the player.

The audio system will only play ﬁles with the extension ".mp3" with

a sampling rate of 22.05 KHz or 44.1 KHz. No other type of ﬁle

(.wma, .mp4, .m3u...) can be played.

The audio equipment searches for all of the music tracks, which

may take anything between a few seconds and several tens of

seconds, before play begins.

On a single disc, the CD player can read up to 255 MP3 ﬁles

spread over 8 folder levels. However, it is advisable to keep to

a limit of two levels to reduce the access time before the CD is

played.

It is advisable to restrict ﬁle names to 20 characters without using

special characters (e.g. " ? ; ù) to avoid any playing or displaying

problems.

While the CD is being played, the folder structure is not followed.

All of the ﬁles are displayed on a single level.

In order to be able to play a recorded CDR or CDRW, when

recording, the ISO 9660 level 1.2 or Joliet ﬁle format is

recommended.

If the disc is recorded in another format, it may not be played

correctly.

To play a disc which has already

been inserted, press the SOURCE

button several times in succession

and select CD.

It is recommended that the same recording format is always

used for an individual disc, with as low a speed as possible

(4x maximum) for optimum sound quality.

Press one of the buttons to select a

folder on the CD.

In the particular case of a multi-session CD, the Joliet format is

recommended.

Press one of the buttons to select a

track on the CD.

Press the LIST REFRESH button to display the list of directories of

the MP3 compilation.

Use only USB memory sticks formatted FAT32 (File Allocation

Table).

Press and hold one of the buttons for

fast forward or backward play.

It is recommended that you use genuine Apple^®USB cables for

correct operation.

317

05 PEUGEOT CONNECT USB

Using the PEUGEOT CONNECT USB

Connecting a USB memory stick

Connect the memory stick to the port, directly or

This unit consists of a USB port and an auxiliary

Jack socket*. The audio ﬁles are transmitted

from a portable device - digital player or a USB

memory stick - to your PEUGEOT Connect

Sound (RD5) and heard via the vehicle's

speakers.

using a lead. If the audio equipment is switched

on, the USB source is detected as soon as it is

connected. Play begins automatically after a delay

which depends on the capacity of the USB memory

stick.

The ﬁle formats supported are .mp3 (mpeg1 layer 3

only) and .wma (standard 9 only, 128 kbits/sec

compression).

USB memory stick or Apple^®player of

generation 5 or later:

Certain playlist formats are supported (.m3u, ...)

On reconnection of the previous memory stick

used, play is resumed automatically with the last

track played.

-

Use only USB memory sticks formatted

FAT32 (File Allocation Table),

the Apple^®player lead is essential,

-

navigation through the ﬁle database is also

possible by means of the steering mounted

controls.

The system puts together playlists (temporary memory) created

over a period which depends on the capacity of the USB device.

The other sources are available during this time.

The playlists are updated each time the ignition is switched off or

each time a USB memory stick is connected.

When connecting for the ﬁrst time, the classiﬁcation suggested

is by folder. When you reconnect, the classiﬁcation selected

previously is retained.

Other Apple^®players of earlier generations and

players using the MTP protocol*:

-

play via Jack-Jack lead only (not supplied),

-

navigation through the ﬁle database is from

the portable device.

* Depending on vehicle.

318

Audio equipment and telematics for Your Peugeot 3008 SUV First Generation (2008-2015)

Related Topics