Get Monitoring Guide for Peugeot 5008 SUV First Generation (2009-2016)

Monitoring

Dials

Instrument panels

1. Rev counter.

Panel grouping together the vehicle operation indication dials and warning lamps.

Indicates the engine speed (x 1 000 rpm).

2. Coolant temperature.

Indicates the temperature of the engine

coolant (° Celsius).

3. Fuel level.

Indicates the quantity of fuel remaining in

the tank.

4. Speedometer.

Indicates the current speed of the moving

vehicle (mph or km/h).

5. Screen.

6. Control switch.

Temporary display of the service indicator

and driving range with the AdBlue^®

additive.

Display and reset the selected function (trip

distance recorder or service indicator).

7. Instrument panel lighting dimmer.

Adjusts the brightness of the lighting of

the instruments and controls, if the vehicle

lighting is on.

For more information, refer to the

section corresponding to the button or

function and its associated display.

14

Monitoring

1

C. Service indicator.

(miles or km) or,

Screen(s)

Engine oil level indicator (depending

on version).

or

distance recorder.

(miles or km)

D. Gear shift indicator.

Electronic or automatic gearbox.

E. Warning messages and function

status messages, trip computer, GPS

navigation information.

Instrument panel navigator

Controls

There are four buttons to control the screen in

the instrument panel:

1. Access the main menu, confirm the

selection.

2. Move up through the menu.

3. Move down through the menu.

4. Return to the previous display, exit from

the menu.

A. Speed limiter

or

This group of buttons permits:

-

When stationary, configuration of the

vehicle's equipment and the screen

settings (languages, units...),

Cruise control.

(mph or km/h)

B. Trip distance recorder.

(miles or km)

-

While driving, scrolling of the active

functions (trip computer, navigation...).

15

Monitoring

Vehicle parameters

Choice of language

The main menu and its associated

functions can only be accessed when

stationary, via buttons 1 to 4.

A message appears in the screen,

above a certain speed threshold,

indicating that the main menu cannot be

displayed.

This menu allows you to select the display

language.

The trip computer displays can only be

accessed while driving, via buttons 2

and 3 (refer to the "Trip computer"

section).

Choice of units

This menu allows you to select the units:

temperature (°Celsius or °Fahrenheit) and fuel

consumption (l/100 km, mpg or km/l).

This menu allows you to activate or deactivate

certain driving and comfort equipment*:

-

wiper linked with reverse gear (refer to the

"Visibility" section),

selective unlocking (refer to the "Access"

section),

guide-me-home lighting (refer to the

"Visibility" section),

directional headlamps (refer to the

"Visibility" section),

Main menu

F

Press button 1 for access to the main menu

and select one of the following functions:

-

"Vehicle parameters",

"Choice of language",

"Choice of units".

F

Press button 2 or 3 to move in the screen.

Press button 1 again to confirm the

selection.

automatic or manual parking brake*

(refer to the "Driving" section).

* Depending on the country of sale.

16

Monitoring

1

Indicator and warning lamps

Visual indicators informing the driver that a system is in operation (operation or deactivation

indicator lamps) or of the occurrence of a fault (warning lamp).

When the ignition is switched on

Associated warnings

The warning lamps may come on

continuously (fixed) or flash.

Certain warning lamps come on for a few

seconds when the vehicle's ignition is

switched on.

When the engine is started, these same

warning lamps should go off.

The illumination of certain warning lamps may

be accompanied by an audible signal and a

message in the multifunction screen.

Certain warning lamps may come on

in one of two different modes. Only by

relating the type of illumination to the

operating status of the vehicle can it

be ascertained whether the situation is

normal or whether a fault has occurred.

If they remain on, before moving off, refer to the

information on the warning lamp concerned.

Operation indicator lamps

If one of the following indicator lamps comes on, this confirms that the corresponding system has come into operation.

Warning lamp

Left-hand

is on

Cause

Action / Observations

flashing with buzzer.

The lighting stalk is pushed down.

direction

indicator

Right-hand

direction

indicator

flashing with buzzer.

fixed.

The lighting stalk is pushed up.

Sidelamps

The lighting stalk is in the

"Sidelamps" position.

17

Monitoring

Warning lamp

is on

Cause

Action / Observations

Dipped beam

headlamps

fixed.

The lighting stalk is in the "Dipped

beam headlamps" position.

Main beam

headlamps

fixed.

The lighting stalk is pulled towards

you.

Pull the stalk to return to dipped beam headlamps.

Front foglamps

Rear foglamps

The front foglamps are switched on.

The rear foglamps are switched on.

Turn the ring on the stalk rearwards twice to switch off

the front foglamps.

Turn the ring on the stalk rearwards to switch off the

rear foglamps.

Diesel engine

pre-heating

The ignition switch is at the

2nd position (ignition on).

Wait until the warning lamp has switched off before starting.

The duration for which the warning lamp is on is determined

by the climatic conditions.

Electric parking

brake

The electric parking brake is applied. Release the electric parking brake to switch off the

warning lamp: with your foot on the brake pedal, pull

the electric parking brake control lever.

Observe the safety recommendations.

For more information on the electric parking brake,

refer to the corresponding section.

18

Monitoring

1

Warning lamp

Deactivation of

is on

Cause

Action / Observations

fixed.

The "automatic application" (on

switching off the engine) and

"automatic release" functions are

deactivated or faulty.

Activate the function (according to country) via the

vehicle configuration menu or contact a PEUGEOT

dealer or a qualified workshop if automatic

application / release is not possible.

For more information on the electric parking brake,

refer to the corresponding section.

the automatic

functions of the

electric parking

brake

Foot on the

brake pedal

fixed.

The brake pedal is not pressed.

You must press the brake pedal firmly to:

-

start the engine with an electronic gearbox

(lever in position N),

-

manually release the parking brake.

flashing.

With an electronic gearbox, if you

hold the vehicle on an incline using

the accelerator for too long, the

clutch overheats.

Use the brake pedal and/or the electric parking brake.

Press the corresponding button to deactivate it.

Parking space

sensors

fixed.

The parking space sensors function

is active.

flashing.

fixed.

The system is measuring the space.

Once the measurement has been done, the warning

lamp comes on fixed again.

Stop & Start

When the vehicle stops (red lights,

traffic jams, ...) the Stop & Start system

has put the engine into STOP mode.

The warning lamp goes off and the engine restarts

automatically in START mode, as soon as you want to

move off.

flashes for a few

seconds, then goes

off.

STOP mode is temporarily

unavailable.

or

START mode is invoked

automatically.

For more information on special cases with STOP

mode and START mode, refer to the "Stop & Start"

section.

19

Monitoring

Deactivation indicator lamps

If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally.

This is may be accompanied by an audible signal and a message on the multifunction screen.

Warning lamp

Passenger's

is on

Cause

Action / Observations

fixed.

The control, located in the glove box, Set the control to the ON position to activate the

airbag system

is set to the OFF position.

The passenger's front airbag is

deactivated.

passenger's front airbag.

In this case, do not fit a child seat in the rearward

facing position.

You can install a "rearward facing"

child seat, unless there is a fault with

the operation of the airbags (Airbag

warning lamp on).

Warning lamps

When the engine is running or the vehicle is being driven, the illumination of one of the following warning lamps indicates a fault which requires action

on the part of the driver.

Any fault resulting in the illumination of a warning lamp must be investigated further by reading the associated message in the multifunction screen.

If you encounter any problems, do not hesitate to contact a PEUGEOT dealer or a qualified workshop.

Warning lamp

STOP

is on

Cause

Action / Observations

fixed, alone or

associated with

another warning lamp,

accompanied by an

audible signal and a

message in the screen.

Illumination of this warning lamp is

associated with a serious fault with

the braking system, power steering,

engine lubrication system or cooling

system.

Stop as soon as it is safe to do so as there is a risk

that the engine will cut out while driving.

Park, switch off the ignition and contact a PEUGEOT

dealer or a qualified workshop.

20

Monitoring

1

Warning lamp

Service

is on

Cause

Action / Observations

on temporarily.

A minor fault has occurred for which

there is no specific warning lamp.

Identify the fault by reading the message shown in the

screen, such as, for example:

-

opening of the doors, boot or bonnet,

engine oil low level,

screenwash low level,

flat remote control battery,

saturation of the particle emission filter (Diesel)

As soon as the traffic conditions permit,

regenerate the filter by driving at a speed of at

least 40 mph (60 km/h) until the service warning

lamp goes off.

-

a fault with the tyre under-inflation detection

system,

...

For any other faults, contact a PEUGEOT dealer or a

qualified workshop.

fixed.

A major fault has occurred for which

there is no specific warning lamp.

Identify the fault by reading the message shown

on the screen and contact a PEUGEOT dealer or a

qualified workshop.

fixed, associated with the The servicing interval has been

Only on BlueHDi Diesel versions.

flashing and then fixed

display of the service

indicator spanner.

exceeded.

Your vehicle must be serviced as soon as possible.

21

Monitoring

Warning lamp

is on

Cause

Action / Observations

Electric parking

brake

flashing.

The electric parking brake is not

applied automatically.

The application/release is faulty.

You must stop as soon as it is safe to do so.

Park on flat level ground, engage a gear (or place the

lever in position P for an automatic gearbox), switch

off the ignition and contact a PEUGEOT dealer or a

qualified workshop.

Electric parking

brake fault

fixed.

The electric parking brake has a fault. Contact a PEUGEOT dealer or a qualified workshop

without delay.

For more information on the electric parking brake,

refer to the corresponding section.

Braking

fixed, associated with

the STOP warning

lamp.

The braking system fluid level has

dropped significantly.

You must stop as soon as it is safe to do so.

Top up with brake fluid recommended by PEUGEOT.

If the problem persists, have the system checked by a

PEUGEOT dealer or a qualified workshop.

+

fixed, associated with the The braking system has a fault.

electric parking brake

malfunction warning

lamp, if the parking brake

is released.

You must stop as soon as it is safe to do so.

Park, switch off the ignition and contact a PEUGEOT

dealer or a qualified workshop.

fixed, associated with

the STOP and ABS

warning lamps.

The electronic brake force distribution You must stop as soon as it is safe to do so.

(EBFD) system has a fault.

Have it checked by a PEUGEOT dealer or a qualified

workshop.

Anti-lock

Braking System

(ABS)

fixed.

The anti-lock braking system has a

fault.

The vehicle retains conventional braking.

Drive carefully at reduced speed and contact a

PEUGEOT dealer or a qualified workshop without

delay.

22

Monitoring

1

Warning lamp

Dynamic

is on

Cause

Action / Observations

flashing.

The DSC/ASR regulation is

operating.

The system optimises traction and improves the

directional stability of the vehicle in the event of loss of

grip or trajectory.

stability control

(DSC/ASR)

fixed.

The DSC/ASR system has a fault.

Have it checked by a PEUGEOT dealer or a qualified

workshop.

Engine

autodiagnosis

system

flashing.

fixed.

The engine management system has Risk of destruction of the catalytic converter.

a fault.

Have it checked by a PEUGEOT dealer or a qualified

workshop.

The emission control system has a

fault.

The warning lamp should go off when the engine is started.

If it does not go off, contact a PEUGEOT dealer or qualified

workshop without delay.

Low fuel level

fixed with the needle

in the red zone.

When it first comes on there remains Refuel as soon as possible to avoid running out of

approximately 6 litres of fuel in the

fuel.

tank.

This warning lamp will come on every time the ignition

At this point, you begin to use the fuel is switched on, until a sufficient addition of fuel is

reserve.

made.

Fuel tank capacity: approximately 60 litres.

Never continue to drive until you run out of fuel, as

this could damage the emission control and injection

systems.

Maximum coolant fixed with the needle in The temperature of the cooling

temperature the red zone. system is too high.

Stop as soon as it is safe to do so.

Wait until the engine has cooled down before topping

up the level, if necessary.

If the problem persists, contact a PEUGEOT dealer or

a qualified workshop.

23

Monitoring

Warning lamp

is on

Cause

Action / Observations

AdBlue^®additive fixed, on switching

(BlueHDi Diesel) on the ignition,

accompanied by an

The remaining driving range is

between 350 miles (600 km) and

1500 miles (2400 km).

Have the AdBlue^®additive tank topped up as soon

as possible: go to a dealer PEUGEOT or a qualified

workshop, or carry out this operation yourself by

referring to the corresponding section.

audible signal and a

message indicating

the remaining driving

range.

+

flashing associated

with the SERVICE

warning lamp,

accompanied by an

audible signal and a

message indicating

the remaining driving

range.

The remaining driving range is

between 0 and 375 miles (600 km).

You must top-up the AdBlue^®additive tank to avoid

a breakdown: go to a dealer PEUGEOT or a qualified

workshop, or carry out this operation yourself by

referring to the corresponding section.

flashing, associated

with the SERVICE

warning lamp,

accompanied by an

audible signal and a

message indicating

that starting is

The AdBlue^®tank is empty: the

starting inhibition system required

by legislation prevents starting of the

engine.

To be able to start the engine, you must top-up the

AdBlue^®additive tank: go to a dealer PEUGEOT or a

qualified workshop, or carry out this operation yourself

by referring to the corresponding section.

It is essential to add at least 3.8 litres of AdBlue^®

to the tank.

prevented.

24

Monitoring

1

Warning lamp

is on

Cause

Action / Observations

This alert disappears once the exhaust emissions

SCR emissions

control system

fixed, on switching on the

ignition, associated with

A fault with the SCR

emissions control system has return to normal levels.

been detected.

(BlueHDi Diesel) the SERVICE and engine

diagnostic warning lamps,

accompanied by an audible

signal and a message

+

indicating an emissions

control fault.

flashing, on switching on

the ignition, associated with

the SERVICE and engine

diagnostic warning lamps,

accompanied by an audible

signal and a message

indicating the remaining

driving range.

The remaining driving range

is between 0 and 650 miles

(1 100 km).

Contact a PEUGEOT dealer or a qualified workshop

without delay, to avoid a breakdown.

flashing, on switching on

the ignition, associated with

the SERVICE and engine

diagnostic warning lamps,

accompanied by an audible

signal and a message

indicating that starting is

prevented.

You have exceeded the

authorised driving limit: the

starting inhibition system

prevents starting of the

engine.

To be able to start the engine, you must call on a

PEUGEOT dealer or a qualified workshop.

25

Monitoring

Warning lamp

is on

Cause

Action / Observations

Engine oil

pressure

fixed.

There is a fault with the engine

lubrication system.

You must stop as soon it is safe to do so.

Park, switch off the ignition and contact a PEUGEOT

dealer or a qualified workshop.

Battery charge

fixed.

The battery charging circuit has a

The warning lamp should go off when the engine is

fault (dirty or loose terminals, slack or started.

cut alternator belt, ...).

If it does not go off, contact a PEUGEOT dealer or a

qualified workshop.

Door(s) open

fixed if the speed is

A door, the boot, the lower tailgate

Close the door or boot.

below 6 mph (10 km/h). or the bonnet (with alarm only) is still

open.

fixed and accompanied

by an audible signal if

the speed is above

6 mph (10 km/h).

Front seat belt

not fastened /

unfastened

fixed then flashing

accompanied by an

increasing audible

signal.

The driver and/or the front passenger Pull the strap then insert the tongue in the buckle.

has not fastened or has unfastened

their seat belt.

Rear seat belt

not fastened /

unfastened

fixed then flashing

accompanied by an

audible signal.

One or more rear passengers have

unfastened their seat belt.

26

Monitoring

1

Warning lamp

Airbags

is on

Cause

Action / Observations

on temporarily.

This lamp comes on for a few

seconds when you turn on the

ignition, then goes off.

This lamp should go off when the engine is started.

If it does not go off, contact a PEUGEOT dealer or a

qualified workshop.

fixed.

One of the airbag or seat belt

pretensioner systems has a fault.

Have it checked by a PEUGEOT dealer or a qualified

workshop.

Water in Diesel

The Diesel fuel filter contains water.

Risk of damage to the injection system on Diesel

engines.

Contact a PEUGEOT dealer or a qualified workshop

without delay.

Directional

headlamps

flashing.

fixed.

The directional headlamps system

has a fault.

Have it checked by a PEUGEOT dealer or a qualified

workshop.

Under-inflation

The pressure in one or more wheels

is too low.

Check the pressure of the tyres as soon as possible.

This check should preferably be carried out when the

tyres are cold.

+

flashing then fixed,

accompanied by the

Service warning lamp. on one of the wheels.

The tyre pressure monitoring system

has a fault or no sensor is detected

Under-inflation detection is not assured.

Have the system checked by a PEUGEOT dealer or a

qualified workshop.

27

Monitoring

Coolant temperature indicator

You must stop as soon as it is safe to do so.

Wait a few minutes before switching off the

engine.

After driving for a few minutes, the temperature

and pressure in the cooling system increase.

To top up the level:

Contact a PEUGEOT dealer or a qualified

workshop.

F

wait for the engine to cool,

unscrew the cap by two turns to allow the

pressure to drop,

F

when the pressure has dropped, remove

the cap,

top up the level to the "MAX" mark.

With the engine running, when the needle is:

-

in zone A, the temperature is correct,

in zone B, the temperature is too high;

the max temperature warning lamp 1 and

the central STOP warning lamp come on,

accompanied by an audible signal and a

message in the screen.

28

Monitoring

1

More than 1 800 miles (3 000 km)

remain before the next service is due

Less than 600 miles (1 000 km)

remain before the next service is due

Service indicator

When the ignition is switched on, no service

information appears in the screen.

Example: 560 miles (900 km) remain before

the next service is due.

For 5 seconds after the ignition is switched on,

the screen indicates:

Between 600 miles (1 000 km) and 1 800 miles

(3 000 km) remain before the next service is due

For 5 seconds after the ignition is switched on,

the spanner symbolising the service operations

comes on. The distance recorder display line

indicates the distance remaining before the

next service is due.

5 seconds after the ignition is switched on,

the distance recorder resumes its normal

operation. The spanner remains on to

indicate that a service must be carried out

soon.

Example: 1 700 miles (2 800 km) remain

before the next service is due.

For 5 seconds after the ignition is switched on,

the screen indicates:

System which informs the driver when the

next service is due, in accordance with the

manufacturer's servicing schedule.

The point at which the service is due is

calculated from the last indicator zero reset,

according to the mileage covered since the last

service.

5 seconds after the ignition is switched on,

the spanner goes off; the distance recorder

resumes its normal operation. The screen then

indicates the total and trip distances.

For BlueHDi Diesel versions, depending on the

country of sale, the level of deterioration of the

engine oil may also be taken into account.

29

Monitoring

The procedure for resetting to zero is as follows:

Service overdue

For BlueHDi versions, the spanner may

also come on early, according to the

level of deterioration of the engine oil,

which depends on the driving conditions

in which the vehicle is used.

F

switch off the ignition,

press and hold the trip distance recorder

zero reset button,

For 5 seconds after the ignition is switched on, the

spanner flashes to indicate that the service must

be carried out as soon as possible.

Example: the service is overdue by 186 miles

(300 km).

F

switch on the ignition; the distance recorder

display begins a countdown,

when the display indicates "=0", release

the button; the spanner disappears.

For 5 seconds after the ignition is switched on,

the screen indicates:

Following this operation, if you wish to

disconnect the battery, lock the vehicle

and wait at least five minutes for the

zero reset to be taken into account.

Service indicator zero reset

5 seconds after the ignition is switched on,

the distance recorder resumes its normal

operation. The spanner remains on.

Retrieving the service

information

You can access the service information at any

time.

F

Press the trip distance recorder zero reset

button.

The service information is displayed for a

few seconds, then disappears.

With BlueHDi Diesel versions, the

Service warning lamp also comes on

when the ignition is switched on.

After each service, the service indicator must

be reset to zero.

30

Monitoring

1

Engine oil level indicator*

Oil level correct

Oil level indicator fault

On versions fitted with an electric oil level

indicator, the state of the engine oil level is

displayed in the instrument panel for a few

seconds when the ignition is switched on, after

the service information.

This is signalled by the flashing of "OIL--" or the

display of a message "Oil level measurement

invalid" in the instrument panel Contact a

PEUGEOT dealer or a qualified workshop.

Oil level low

In the event of a fault with the electric indicator,

the engine oil level is no longer monitored.

When the system has a fault, you should check

the engine oil level using the manual dipstick

(located under the bonnet).

This is signalled by the flashing of "OIL", or the

display of a message "Oil level incorrect" in the

instrument panel, accompanied by illumination

of the service warning lamp and an audible

signal.

If the low oil level is confirmed by a check using

the dipstick, the level must be topped up to

prevent damage to the engine.

Refer to the "Checks of levels" section.

The level shown will only be correct if

the vehicle is on level ground and the

engine has been off for more than

30 minutes.

* Depending on version.

31

Monitoring

Activation

When the vehicle lighting is on:

Distance recorders

The total and trip distances are displayed for

thirty seconds when the ignition is switched off,

when the driver's door is opened and when the

vehicle is locked or unlocked.

Trip distance recorder

It measures a distance travelled since it was

reset to zero by the driver.

F

press the button to change the brightness

of the instrument panel,

F

when the lighting reaches the minimum

setting, release the button, then press

again to increase it,

When traveling abroad, you may

have to change the units of distance:

the display of road speed must be in

the official units (miles or km) for the

country. The change of units is done via

the screen configuration menu, with the

vehicle stationary.

or

F

when the lighting reaches the maximum

setting, release the button, then press

again to reduce it,

when the lighting reaches the level of

brightness required, release the button.

F

With the ignition on, press the button until

zeros appear.

F

Lighting dimmer

System for manual adjustment of the

brightness of the instrument panel in relation to

the exterior brightness.

When the vehicle lighting is on, you

cannot switch the instrument panel

lighting off but you can adjust it to

minimum.

Total distance recorder

It measures the total distance travelled by the

vehicle since its first registration.

Deactivation

When the lighting is off, or in day mode on

vehicles fitted with daytime running lamps,

pressing the button does not have any effect.

32

Monitoring

1

Monochrome screen A (without audio equipment)

Displays in the screen

Controls

Main menu

F

Press the "MENU" button to scroll through

the various menus of the main menu:

-

vehicle configuration,

options,

display settings,

languages,

units.

This displays the following information:

There are three display control buttons:

Press the "OK" button to select the menu

-

time,

date,

-

"ESC" to abandon the operation in

progress,

"MENU" to scroll through the menus or

sub-menus,

"OK" to select the menu or sub-menu

required.

ambient temperature* (this flashes if there

is a risk of ice),

alert messages,

trip computer (refer to the end of the

section).

-

Warning messages (e.g.: "Emission control

system faulty") or information messages (e.g.:

"Boot open") may appear temporarily. Some

can be cleared by pressing the "ESC" button.

* With air conditioning only.

33

Monitoring

Vehicle conﬁguration

Date and time

Languages

Once the "Display settings" menu has been selected,

you can gain access to the following settings:

Once the "Languages" menu has been

selected, you can change the language used

by the display (Français, Italiano, Nederlands,

Portugues, Portugues-Brasil, Türkçe, Deutsch,

English, Espanol).

-

year,

month,

day,

hour,

minutes,

12 or 24 hour mode.

Once the "Vehicle configuration" menu has

been selected, you can activate or deactivate

the following equipment (according to country):

Units

Once the "Units" menu has been selected, you

can change the units for:

-

wiper linked with reverse gear (refer to the

"Visibility" section),

selective unlocking (refer to the "Access"

section),

"guide-me-home" lighting (refer to the

"Visibility" section),

directional headlamps (refer to the

"Visibility" section),

automatic parking brake** (refer to the

"Driving" section),

parking space sensors (se the "Driving"

section),

-

temperature (°C or °F),

-

fuel consumption (l/100 km, mpg or km/l).

F

Once you have selected a setting, press

the "OK" button to change its value.

For safety reasons, configuration of the

multifunction screen by the driver must

only be done when stationary.

...

F

Wait for approximately ten seconds without

any action to allow the changed data to

be recorded or press the "ESC" button to

cancel.

Options

Once the "Options" menu has been selected,

you can start diagnostics of the status of the

equipment (active, not active, faulty).

The screen then returns to the normal display.

** Depending on country of sale.

34

Monitoring

1

Monochrome screen A (with audio equipment)

Displays in the screen

Controls

Main menu

F

Press the "MENU" button for access to

the main menu, then press the "5" or

"6" buttons to scroll through the various

menus:

-

radio-CD,

vehicle configuration,

options,

display settings,

languages,

units.

From the audio equipment control panel, you

can:

This displays the following information:

F

press the "MENU" button to gain access to

the main menu,

-

time,

date,

press the "5" or "6" buttons to scroll

through the items on the screen,

press the "MODE" button to change the

permanent application (trip computer,

audio source, ...),

ambient temperature* (this flashes if there

is a risk of ice),

F

Press the "OK" button to select the menu

required.

-

alert messages,

Radio-CD

audio sources (radio, CD, ...),

trip computer (refer to the corresponding

section).

With the audio equipment switched on, once

the "Radio-CD" menu has been selected you

can activate or deactivate the functions linked

with use of the radio (RDS, REG), the CD or the

CD changer (introscan, shuffle, CD repeat).

F

press the "7" or "8" buttons to change a

setting value,

press the "OK" button to confirm,

or

Warning messages (e.g.: "Emission control

system faulty") or information messages (e.g.:

"Boot open") may appear temporarily. Some

can be cleared by pressing the "^<] arrow"

button.

F

press this button to abandon the

operation in progress.

For more information on the "Radio-

CD" application, refer to the "Audio

equipment and telematics" section.

* With air conditioning only.

35

Monitoring

Vehicle conﬁguration

Date and time

Languages

Once the "DATE AND TIME" menu has been

selected, you can gain access to the following settings:

Once the "Languages" menu has been

selected, you can change the language used

by the display.

-

year,

month,

day,

hour,

minutes,

12 or 24 hour mode.

Once the "Vehicle Configuration" menu has

been selected, you can activate or deactivate

the following equipment (according to country):

Units

Once the "Units" menu has been selected,

you can change the units of the following

parameters:

-

wiper linked with reverse gear (refer to the

"Visibility" section),

selective unlocking (refer to the "Access"

section),

guide-me-home lighting (refer to the

"Visibility" section),

directional headlamps (refer to the

"Visibility" section),

-

temperature (°C or °F),

-

fuel consumption (l/100 km, mpg or km/l).

F

Once you have selected a setting, press

the "7" or "8" buttons to change its value.

automatic parking brake** (refer to the

"Driving" section),

...

For safety reasons, configuration of the

multifunction screen by the driver must

only be done when stationary.

F

Press the "5" or "6" buttons to switch

respectively to the previous or next setting.

Press the "OK" button to record the

change and return to the normal display or

press the "^<] arrow" button to cancel.

Options

Once the "Options" menu has been selected,

you can start diagnostics of the status of the

equipment (active, not active, faulty).

** Depending on the country of sale.

36

Monitoring

1

Monochrome screen C (with PEUGEOT Connect Sound (RD5))

Displays in the screen

Controls

Main menu

F

Press the "MENU" button for access to the

main menu:

-

audio functions,

trip computer (see the corresponding

section),

From the audio equipment control panel, you

can:

-

personalisation-configuration,

telephone (Bluetooth system).

F

press the "MENU" button for access to the

main menu,

Press the"5" or "6" button to select the

menu required, then confirm by pressing

the "OK" button.

Displays according to context:

-

time,

date,

press the "5" or "6" buttons to scroll

through the items on the screen,

press the "MODE" button to change the

permanent application (trip computer,

audio source...),

ambient temperature with air conditioning

(the value displayed flashes if there is a

risk of ice),

"Audio functions"

menu

-

audio functions,

trip computer (see the corresponding

section),

F

press the "7" or "8" buttons to change a

setting value,

press the "OK" button to confirm,

or

With the audio equipment switched on, once

this menu has been selected you can activate

or deactivate the functions linked with use

of the radio (RDS, REG, RadioText) or CD

(introscan, shuffle, CD repeat).

-

alert messages,

screen and vehicle equipment parameter

setting menus.

F

press this button to abandon the

operation in progress.

For more information on the "Audio

functions" application, refer to the

PEUGEOT Connect Sound (RD5) section.

37

Monitoring

Enter the distance to the

destination

"Trip computer"

"Personalisation-

Configuration"

menu

Once this menu has been selected, you can

consult information concerning the status of the

vehicle (alert log, status of the functions...).

This allows you to enter an approximate value

for the distance to the final destination.

F

Press the "MENU" button to gain access

to the general menu.

Press the arrows, then the "OK" button to

select the "Trip computer" menu.

Once this menu has been selected, you can

gain access to the following functions:

-

define the vehicle parameters,

display configuration,

choice of language.

Alert log

This summarises the active warning messages,

displaying them in succession in the

multifunction screen

Deﬁne the vehicle parameters

Once this menu has been selected, you can

activate or deactivate the following equipment

(according to country):

Status of functions

This summarises the status of the functions

present on the vehicle.

-

wiper linked with reverse gear (see

"Visibility" section),

selective unlocking (see the "Access"

section),

guide-me-home lighting (see the "Visibility"

section),

directional headlamps (see the "Visibility"

section),

F

On the "Trip computer" menu, select one

of the applications:

automatic parking brake* (see the "Driving"

section),

...

* Depending on the country of sale.

38

Monitoring

1

Example: setting of the duration of the guide-

me-home lighting

F

Adjust the settings one by one, confirming

with the "OK" button.

Press the "5" or "6" button, then the "OK"

button to select the "OK" box and confirm,

or the "Back" button to cancel.

F

Press the "5" or "6" buttons, then the "OK"

button to select the menu required.

F

Press the "5" or "6" buttons, then the "OK"

button to select the "OK" box and confirm

or press the "^<] arrow" button to cancel.

Choice of language

Once this menu has been selected, you can

change the screen display language.

Display conﬁguration

Once this menu has been selected, you have

access to the following settings:

F

Press the "5" or "6" buttons, then the

"OK" button to select the "Guide-me-home

headlamps" line.

"Telephone" menu

-

brightness-video setting,

date and time setting,

selection of the units.

With the audio equipment switched on, once

this menu has been selected you can configure

your Bluetooth hands-free kit (pairing), consult

the various telephone directories (calls log,

services...) and manage your communications

(pick up, hang up, call waiting, secret mode...).

Adjusting the date and time

F

Press the "7" or "8" button to select the

"Display configuration" menu, then the

"OK" button.

Press the "5" or "6" button, to select the

"Adjust date and time" line, then on the

"OK" button.

Press the "7" or "8" button to select the

setting to modify. Confirm by pressing the

"OK" button then adjust the setting and

confirm again to save the modification.

F

Press the "7" or "8" buttons to set the

value required (15, 30 or 60 seconds), then

press the "OK" button to confirm.

For more information on the telephone

application, refer to the PEUGEOT

Connect Sound (RD5) section.

For safety reasons, configuration of the

multifunction screen by the driver must

only be done when stationary.

39

Monitoring

16/9 retractable colour screen (PEUGEOT Connect Navigation (RT6))

Displays in the screen

Controls

"SETUP" menu

From the navigation system control panel, to

select one of the applications:

F

Press the "SETUP" button to open the

configuration menu:

F

press the dedicated "RADIO", "MUSIC",

"NAV", "TRAFFIC", "PHONE" or

"SETUP" button for access to the

corresponding menu,

turn the dial A to select a function, an item

in a list,

press button B to confirm the selection,

or

press the "Back" button to abandon the

current operation and return to the previous

display.

-

"Display configuration",

"Speech synthesis setting".

"Select language",

"Define vehicle parameters",

"Alert log".

Depending on the context, it displays the

following information:

-

time,

date,

altitude,

F

ambient temperature (the value displayed

flashes if there is a risk of ice),

parking sensor information,

parking space measurement,

audio functions,

directory and telephone information,

satellite navigation system information,

trip computer,

For the operation of the retractable

screen (opening, closing, adjusting the

position...), refer to the "Access to the

retractable screen" section.

-

With repeated presses on the C "MODE"

button, the screen displays:

For safety reasons, configuration of the

multifunction screen by the driver must

only be done when stationary.

-

"RADIO / MEDIA"*,

"TELEPHONE"*,

"FULL SCREEN MAP"*,

"MAP IN A WINDOW"*,

"TRIP COMPUTER".

alert messages,

settings menus for the screen, the satellite

navigation system and vehicle systems.

the image from the reversing camera.

-

* For more information on these applications,

refer to the "Audio equipment and telematics"

section.

40

Monitoring

1

Display conﬁguration

Adjusting the voice synthesiser

This menu is used to select the colour scheme

for the screen, adjust the brightness, set the

date and time and to choose the units for

distance (km or miles), fuel consumption

(l/100 km, mpg or km/l) and temperature

(°Celsius or °Fahrenheit).

This menu is used to adjust the volume setting

for navigation instructions and to choose the

type of voice (male or female).

-

"Vehicle access" (see "Access" section):

● "Plip action: all doors, driver only"

(Selective unlocking of the driver's door),

"Lighting configuration" (see "Visibility"

section):

● "Duration of guide me home lighting:

OFF / 15 s / 30 s / 60 s" (Automatic

guide me home lighting),

Choice of language

This menu is used to choose the language

used by the screen from a defined list.

Adjusting the date and time

● "Directional headlights": ON / OFF"

(Main / additional directional lighting).

-

Press on SETUP.

Select "Display configuration" and confirm.

Select "Set date and time" and confirm.

Vehicle parameters

This menu is used to activate or deactivate

certain driving and comfort systems, classified

by category:

Select "Minute adjustment via GPS" so that the

minutes are adjusted automatically by satellite

reception.

-

"Driver aid":

● "Electric brake*" (Automatic electric

parking brake; see "Driving" section),

"Wiper operation":

Alert log

This lists the active alerts by displaying in turn

the different messages associated with them.

-

Select the setting to modify. Confirm by

pressing on OK, then modify the setting

and confirm again to save the modification.

Adjust the settings one by one.

-

● "Rear wiper operates in reverse:

ON / OFF" (rear wiper coupled to

reverse gear; see the "Visibility"

section),

-

Select "OK" in the screen then confirm to

save the setting.

* Depending on country.

41

Monitoring

16/9 retractable colour screen (PEUGEOT Connect Media Navigation (NG4 3D))

Displays in the screen

Controls

For more information on these

applications, refer to the "Audio

equipment and telematics" section.

For operation of the retractable screen

(opening, closing, adjustment of the

position, etc.), refer to the paragraph

"Access to the retractable screen".

According to context, it displays the following

information:

-

time,

date,

altitude,

From the navigation system control panel:

F

press the dedicated "RADIO", "MUSIC",

"NAV", "TRAFFIC", "SETUP" or

"PHONE" button for access to the

corresponding menu,

ambient temperature (the value displayed

flashes if there is a risk of ice),

audio functions,

satellite navigation system information.

visual parking assistance,

the result of the measurement of free

space,

contacts and telephone information,

configuration menus for the screen and the

navigation system,

-

F

or

turn the navigator knob A to move the

selection,

press the "OK" navigator central button B

to confirm the selection,

-

F

press the this button to abandon

the current operation and return

to the previous display.

42

Monitoring

1

"SETUP" menu

F

Press the "SETUP" button for access to

the "SETUP" menu. It allows you to adjust

settings for the following functions:

Date and time

Display

F

Press "SETUP".

Select "Display configuration" and confirm.

Select "Adjust date and time" and confirm.

This menu allows you to set the brightness of

the screen, the screen colour scheme and the

colour of the map (day/night or auto mode).

-

"Languages and voice functions"

"Date and time",

"Display screen",

"Units",

"System parameters".

Select "Synchronise minutes with GPS" for the

adjustment of minutes to be done automatically

by satellite reception.

Units

This menu allows you to select the units:

temperature (°C or °F) and fuel consumption

(km/l, l/100 or mpg).

Languages and voice functions

This menu allows you to:

F

Select the setting to modify. Confirm by

pressing "OK", then adjust the setting and

confirm again.

-

select the language used by the display,

select the settings for voice recognition

(on/off, instructions on use, personal voice

training...),

F

Adjust the settings one by one.

Select "OK" in the screen then confirm to

save the settings.

System parameters

This menu allows you to restore the factory

configuration, display the software version and

activate scrolling text.

-

adjust the volume of the voice synthesiser.

For safety reasons, configuration of the

multifunction screen by the driver must

only be done when stationary.

43

Monitoring

Access to the retractable screen

If you have closed the screen, it will

open again automatically:

-

on switching on the audio and

navigation system (unless it had

been closed manually while the

system was in operation),

when an outgoing telephone call is

made,

-

when a voice command is given,

when a warning message linked

with the STOP warning lamp is

displayed (PEUGEOT Connect

Navigation (RT6)).

The screen opens automatically when the

ignition is switched on. It closes automatically

three seconds after switching off the ignition if

the audio and telematics system is switched off.

Adjusting the angle of the screen

You can adjust the angle of the screen to one of

four defined positions, by repeated presses on

the front or back of the control B. The position

of the screen is memorised on closing.

You can open or close the screen at any time,

with the ignition on, using control A.

-

Press button A: the screen folds.

Press button A again: the screen opens

again.

44

Monitoring

1

Trip computer

System that gives you information on the current journey (range, fuel consumption…).

Monochrome screen A

The trip computer provides the following

information:

F

The next press returns you to the normal

display.

-

range,

Information displays

Zero reset

current fuel consumption,

distance travelled,

average fuel consumption,

average speed.

F

Press the button, located at the end of the

wiper stalk, to display the various items of

trip computer data in succession.

F Press the control for more than

two seconds to reset to zero the distance

travelled, the average fuel consumption

and the average speed.

45

Monitoring

Trip computer

System which provides current information concerning the trip (range, consumption…).

Monochrome screen C

Information displays

16/9 colour screen

In the screen C or the colour screen

Depending on your vehicle's equipment, the

trip computer information appears on the

multifunction screen or on the instrument panel

screen.

F

Press the button, located at the end of

the wiper stalk, to display the various trip

computer tabs in succession.

Instrument panel screen

In the instrument panel screen

F

Press the up and down arrows on

the navigator to display the various

trip computer tabs in succession.

46

Monitoring

1

-

The current information tab

with:

● the range,

Trip zero reset

● the current fuel

consumption,

● the distance remaining to be

travelled.

-

The trip "1" tab with:

● the distance travelled,

● the average fuel

consumption,

● the average speed,

for the first trip.

With the screen C or the colour screen

With the instrument panel screen

F

When the trip required is displayed, press

the control for more than two seconds.

F

When the required trip is displayed, press

the "OK" button on the navigator for more

than two seconds.

-

The trip "2" tab with:

● the distance travelled,

● the average fuel

consumption,

● the average speed,

for the second trip.

Trips "1" and "2" are independent but their use

is identical.

For example, trip "1" can be used for daily

figures, and trip "2" for monthly figures.

F

Pressing the button again takes you to a

black screen.

A further press returns you to the normal

display.

47

Monitoring

Trip computer, a few definitions

Range

Current fuel consumption

Distance travelled

(miles or km)

(mpg or l/100 km or km/l)

(miles or km)

The distance which can still be

Calculated over the last few seconds.

Calculated since the last trip

computer reset.

travelled with the fuel remaining in the tank

(related to the average fuel consumption over

the last few miles (kilometres) travelled).

Distance remaining

to destination

This function is only displayed from

20 mph (30 km/h).

(miles or km)

This value may vary following a change

in the style of driving or the relief,

resulting in a significant change in the

current fuel consumption.

This is the distance remaining to be travelled

to the final destination. It is either calculated

instantly by the navigation system, if guidance

is activated, or entered by the user.

If the distance is not entered, dashes are

displayed in place of the digits.

Average fuel

consumption

(mpg or l/100 km or km/l)

Calculated since the last trip

computer reset.

When the range falls below 20 miles (30 km),

dashes are displayed. After filling with at least

5 litres of fuel, the range is recalculated and is

displayed when it exceeds 60 miles (100 km).

Stop & Start time counter

(minutes / seconds or hours /

minutes)

Average speed

(mph or km/h)

Calculated since the last trip

computer reset.

If your vehicle is fitted with Stop &

Start, a time counter calculates the time spent

in STOP mode during a journey.

It resets to zero every time the ignition is

switched on with the key.

If dashes are displayed continuously

while driving in place of the digits,

contact a PEUGEOT dealer or a

qualified workshop.

48

Monitoring for Your Peugeot 5008 SUV First Generation (2009-2016)

Related Topics