Dashboard Instruments And Control for Your Peugeot Expert Van Third Generation (2016-2025)

Getting to know your vehicle  
Folding  
► To restore the bench seat to the original  
position pull the loop to unlock it.  
► Suspend and engage the rod of net at one  
side, compress rod and suspend and engage  
at the other side.  
2
► Take the handle to fold the bench seat to  
the back until it is engaged in the original  
position.  
Installation on the floor  
Tilt up the head restraints.  
a) Installation with lashing eyes.  
►
Attach the hooks of safety net straps  
in the lashing eyes.  
Safety net  
Safety net behind the seats  
Depending on version, the safety net can be  
installed behind the second row seats, the third  
row seats or behind the front seats.  
To increase the loading capacity the seats  
behind the safety net can be folded or removed.  
Seat backrests in front of the safety net must be  
raised up.  
► Tilt the head restraints to the front.  
Pull the loop upwards to unlock the bench  
seat.  
Passengers must not be transported behind the  
safety net.  
Installation in the roof frame  
► Raise the bench seat taking the handle and  
fold the bench seat to the front until it is  
engaged.  
Unfolding  
b) Installation with rear seats on rails  
Insert the fixings in the floor ancho-  
rages on both sides. To lock the fix-  
ings turn them clockwise a quarter  
turn. Place them as close as possible  
to the end of the rail.  
► There are installation openings on both sides  
in the roof frame. If present, open the covers.  
67  
Getting to know your vehicle  
c) Installation with fixed rear seats  
Insert the fixings in the floor ancho-  
rages on both sides.  
Tension both straps by pulling at the  
loose end.  
►
Safety net on the floor  
Attached to the lashing eyes on the rear floor, it  
allows objects to be held down.  
It is possible to install the safety net  
together with folded seats.  
68  
Dashboard Instruments And Control  
Instrument Panel  
3
69  
Dashboard Instruments And Control  
Type A  
18.  
Central locking system  
Automatic locking  
Electric child locks  
Hazard warning flashers  
Power sliding doors  
1.  
2.  
3.  
4.  
Power windows  
Exterior mirrors  
Side air vents  
Lane keep assist  
Descent control system  
Heated steering wheel  
19.  
20.  
Drive modes  
Selector drive unit  
Selector automatic transmission  
Type B  
5.  
6.  
High beam  
Headlight flash  
Turn lights  
Fog lights  
Parking lights  
21.  
22.  
23.  
24.  
Power button  
Steering wheel adjustment  
Horn  
Cruise control system  
Speed limiter  
Temperature preconditioning  
Anti-theft system  
Adaptive cruise control  
Heated windscreen  
Odometer  
The total recorded distance is displayed in km.  
7.  
8.  
9.  
Driver Information Centre  
Infotainment controls  
25.  
26.  
27.  
28.  
Headlight range adjustment  
Bonnet release lever  
Fuse box  
Type A  
Windscreen wiper and washer  
Rear window wiper and washer  
Electric parking brake  
10.  
11.  
12.  
13.  
Info Display  
Front storage  
Front storage  
Instrument Cluster  
Type B  
Speedometer  
Indicates vehicle speed.  
Airbag deactivation  
Power outlet  
14.  
15.  
16.  
17.  
Glovebox  
Centre air vents  
Climate control system  
Inductive charging  
70  
Dashboard Instruments And Control  
Type B  
Trip odometer  
Fuel level gauge  
3
The recorded distance since the last reset is  
displayed in the Driver Information Centre.  
Two trip odometer pages are selectable in the  
trip / autonomy information menu for different  
trips.  
Control indicator  
the fuel level is low.  
Never run the fuel tank dry.  
The arrow indicates the vehicle side where the  
fuel filler flap is located.  
The top-up quantity may be less than the  
specified fuel tank capacity, due to the remaining  
fuel in the tank.  
or  
illuminates yellow if  
Trip odometer counts up to 9,999 km.  
Tachometer  
Displays the engine speed.  
Type A  
Drive in a low engine speed range for each gear  
as much as possible.  
Caution  
If the indicator is in the red warning  
zone, the maximum permitted engine speed  
is exceeded. The engine can be damaged.  
Type B  
Type A  
Press button for two seconds to reset the trip  
odometer.  
Type A  
Type B  
Hydrogen gauge  
Displays the hydrogen level in the tank.  
71  
Dashboard Instruments And Control  
Trip pages  
Type A  
If the control indicator  
illuminates yellow,  
refuel the tank immediately.  
If additionally the charging level of the high  
voltage battery is too low,  
illuminates yellow.  
Combined range  
To reset a trip, press the button for more than  
two seconds when the desired trip is displayed.  
Type B  
The combined range (high voltage battery and  
hydrogen tank) is shown.  
The range is calculated from the current  
hydrogen level, the charging level of the  
high voltage battery and from the current  
consumption. The display shows average  
values.  
Trip computer  
The trip computer displays current trip  
After refuelling or charging, the range is updated  
automatically after a brief delay.  
information since the last reset.  
Information menu  
Average speed  
Instantaneous consumption  
Display of average speed.  
Average consumption  
Display of the instantaneous consumption of  
combined energy (fuel cell and high voltage  
battery).  
Display of the average consumption of combined  
energy (fuel cell and high voltage battery). After  
a reset it starts with a default value.  
Odometer  
The recorded overall distance.  
Trip odometer  
The recorded distance since the reset.  
High-voltage battery  
charge status  
Pressing the button displays the following tabs in  
turn:  
-
current information  
Displays the high-voltage battery state of charge.  
72  
Dashboard Instruments And Control  
● total range  
Type A  
Type A  
● current consumption  
● time counter for the stop-start mode  
● total distance recorder  
trip 1  
3
-
-
● average speed  
● average consumption  
● distance travelled  
trip 2  
Type B  
Type B  
● average speed  
● average consumption  
● distance travelled  
The time counter is reset each time the ignition  
is switched on.  
To reset a trip, press the button for more than  
two seconds when the desired trip is displayed.  
Comfort consumption  
gauge  
The comfort consumption gauge informs about  
the current electric consumption caused by the  
following thermal consumers:  
Engine coolant  
temperature gauge  
Displays the coolant temperature.  
The red zone indicates that the operating  
temperature of the engine is too high.  
Power flow  
The power indicator gauge informs about the  
current energy situation of the vehicle.  
-
-
-
-
-
heating  
Caution  
Charge: High-voltage battery is being  
charged with energy resulting from  
braking or deceleration of the  
vehicle  
air conditioning  
heated windscreen  
heated rear window  
heated seats  
If engine coolant temperature is too high,  
stop vehicle, switch off engine. Danger to  
engine. Check coolant level.  
Eco:  
An optimum in energy is accessible  
in all driving modes  
Type A  
If the drive mode Eco mode is selected,  
the performance of the thermal consumers is  
reduced.  
Power: Vehicle is driven in a dynamic  
driving style with focus on  
performance.  
73  
Dashboard Instruments And Control  
If no service is required for the next 3000 km  
or more no service information appears in the  
display.  
Type B  
If service is required within the next 3000 km,  
the remaining distance to the next service due,  
the distance travelled since the last service due  
or the time period that remains to the next  
service due is indicated for several seconds.  
The Driver Information Centre can display one  
widget per page, the Info Display can contain  
several widgets.  
Simultaneously symbol  
as reminder.  
illuminates temporary  
Engine oil level monitor  
E
If service is required in less than 1000 km,  
the remaining distance to the next service due,  
the distance travelled since the last service due  
or the time period that remains to the next  
service due is indicated for several seconds.  
To add a widget to a page, touch  
.
The state of the engine oil level is displayed in  
the Driver Information Centre for a few seconds  
following the service information after switching  
on the ignition.  
Warning, lights, indicators  
and messages  
A proper state of engine oil level is confirmed.  
Simultaneously  
reminder.  
illuminates permanently as  
If engine oil level is low,  
flashes and warning  
message is indicated in the Driver Information  
Control indicators  
Overdued service is indicated by a message in  
the Driver Information Centre which indicates  
Centre.  
Depending on the version,  
The control indicators described are not present  
in all vehicles. The description applies to  
all instrument versions. Depending on the  
equipment, the position of the control indicators  
may vary. When the ignition is switched on,  
most control indicators will illuminate briefly as  
a functionality test.  
D
flashes in the  
the overdued distance.  
flashes and then  
Driver Information Centre. Confirm engine oil  
level by using the oil dipstick and top up engine  
illuminates permanently until service is executed.  
oil respectively.  
A fault of measurement is indicated by  
Reset of service interval  
D
or  
After each service, the service indicator must  
be reset to ensure proper functionality. It is  
recommended to seek the assistance of a  
workshop.  
a message in the Driver Information Centre  
together with . Check engine oil level  
manually by using the dipstick.  
The control indicator colours mean:  
red :  
danger, important reminder  
warning, information, fault  
confirmation of activation  
confirmation of activation  
confirmation of activation  
Retrieving service information  
Service display  
yellow :  
green :  
blue :  
The status of the service information can be  
retrieved at any time via the Info Display. Press  
Check in the vehicle settings menu. The service  
information is displayed for a few seconds.  
The service system informs the driver when to  
change the engine oil and filter or a vehicle  
service is required. Based on driving conditions,  
the interval at which an engine oil and filter  
change is required can vary considerably.  
A required service due is displayed in the Driver  
Information Centre for several seconds after  
switching on the ignition.  
white :  
grey :  
Widgets  
A widget is the indication of specific information  
or gauge, e.g. radio information, navigation  
information or the engine coolant temperature  
gauge.  
system paused, at least one  
system limitation has been  
detected  
74  
Dashboard Instruments And Control  
Control indicators are located in the Driver  
Information Centre.  
HV charging cable connected  
Gear shifting  
(2)  
3
(2)  
Overview  
The numbers in the overview table indicate what  
to do, when a control indicator illuminates or  
flashes.  
High voltage battery temperature  
high  
Low hydrogen level  
(2)  
(4)  
(1):  
(2):  
(3):  
(4):  
only for information.  
Orange warning and indicator lamps  
12 V battery charging system  
information and warning.  
seek the assistance of a workshop.  
Service vehicle soon  
(4)  
(5)  
Door open  
stop engine, leave vehicle and seek the  
assistance of a workshop.  
Power steering  
(2)  
(4)  
(5):  
have the cause of the fault remedied  
immediately by a workshop.  
Seat belt reminder  
(2)  
Preheating  
(1)  
Red warning and indicator lamps  
Electric parking brake  
(1)/(5)  
Exhaust filter  
Stop engine  
(1)/(3)  
(4)  
Brake system  
(5)  
Water in fuel filter  
(2)  
Hydrogen leakage  
(2)/(5)  
Rain sensor  
(1)  
Low fuel  
Engine coolant temperature high  
(2)  
(4)  
Side blind spot alert  
HV battery level low  
(2)  
Engine oil pressure  
(2)  
(4)  
Airbag activated  
HV reduced engine power  
(2)  
Service vehicle soon  
(2)  
(5)  
Airbag deactivated  
(2)  
75  
Dashboard Instruments And Control  
HV pedestrian safety alert fault  
Electronic Stability Control and  
Traction Control system deactiva-  
ted  
Vehicle ready  
(3)  
(1)  
Malfunction indicator light  
(2)  
Descent control system  
(5)  
(2)  
Traffic sign assistant  
System check  
(2)/(3)  
Turn lights  
(1)  
(4)  
Lane keep assist  
AdBlue  
(1)  
(2)  
Daytime running lights/sidelights  
(1)  
Driver alert  
(2)/(3)  
Fuel cell system fault  
(2)/(3)  
Low beam  
(1)  
Airbag and belt tensioners  
(5)  
Automatic operation of electric  
parking brake deactivated  
High beam assist  
(1)  
Tyre deflation detection system  
(2)/(3)  
(1)  
Front fog lights  
(1)  
Electric parking brake fault  
Parking assist  
(5)  
(1)/(3)  
Blue warning and indicator lamps  
Braking  
(4)  
Stop-start system deactivated  
High beam  
(1)  
(1)  
Active emergency braking  
Rear fog light  
(1)  
(2)/(3)  
Major Fault - Stop The  
Vehicle  
Antilock brake system (ABS)  
Green warning and indicator lamps  
(2)  
Stop-start system  
Fixed, associated with another warning  
lamp, accompanied by the display of a message  
and an audible signal.  
Electronic stability control and  
traction control system  
(1)  
(2)/(5)  
76  
Dashboard Instruments And Control  
A serious fault with the engine, braking system,  
power steering or automatic gearbox or a major  
electrical fault has been detected.  
The brake fluid level in the braking circuit has  
dropped significantly.  
Fixed, accompanied by the display of a  
message and an audible signal.  
The system has a fault.  
3
Fixed.  
A minor fault with the braking system has been  
detected.  
Drive carefully.  
Air Bag Warning Light  
Fixed, accompanied by the display of the  
message "Driving Assistance Sensor blind:  
Clean sensor, see User Manual ".  
The sensor is masked.  
Stop as soon as it is safe to do so and switch off  
the ignition.  
Fixed.  
The front passenger airbag is activated.  
The control is set to the "ON" position.  
Battery Charge Warning  
Light  
In this case, do not install a "rearward  
facing" child seat on the front passenger seat  
- risk of serious injury!  
Clean the front camera.  
Fixed.  
Power Steering Fault  
Warning Light  
The battery charging circuit is faulty (e.g. dirty  
terminals, loose or severed alternator belt).  
Fixed.  
The front passenger airbag is deactivated.  
The control is set to the “OFF” position.  
A "rearward facing" child seat can be installed,  
unless there is a fault with the airbags (Airbags  
warning lamp on).  
Door Open Warning Light  
Fixed.  
A minor fault in the power steering has been  
detected. Drive carefully at moderate speed.  
Fixed, associated with a message  
indicating which access is open.  
An audible signal supplements the alert if the  
speed is higher than 6 mph (10 km/h).  
A door, the boot, the tailgate or the opening rear  
screen is still open (depending on version).  
Close whichever access is open.  
If your vehicle is equipped with a right-hand side-  
hinged door, this warning lamp will not indicate  
that it is open.  
Fixed.  
Engine Coolant  
Temperature Warning  
Light  
One of the airbags or seat belt pyrotechnic  
pretensioners is faulty.  
Brake Warning Light  
Fixed.  
Fixed.  
The temperature of the cooling system is too  
high.  
The electric parking brake is applied.  
Flashing.  
Drowsy Driver Detected  
Warning Light  
Application/release is faulty.  
Fixed.  
Oil Pressure Warning  
Light  
The parking brake is applied or not properly  
released.  
Fixed.  
The system is deactivated.  
Fixed.  
Fixed.  
There is a fault with the engine lubrication  
system.  
77  
Dashboard Instruments And Control  
One or more minor faults, for which there is/  
are no specific warning lamp(s), have been  
detected.  
Identify the cause of the fault using the message  
displayed on the instrument panel.  
You may be able to deal with some faults  
yourself, such as changing the battery in the  
remote control.  
Charging Cable  
Connected Warning Light  
Fixed when the ignition is switched on.  
Traction Battery  
Temperature Warning  
Light  
The charging cable is connected to the vehicle's  
connector.  
Fixed, combined with the STOP  
warning lamp, accompanied by the display of a  
message and an audible signal.  
Fixed when the ignition is switched on,  
accompanied by a message.  
It is not possible to start the vehicle while the  
charging cable is connected to the vehicle’s  
connector.  
Fixed, accompanied by the display of a  
message.  
One or more major faults, for which there is/  
are no specific warning lamp(s), have been  
detected.  
The traction battery's temperature is too high.  
Evacuate the vehicle as quickly as possible  
and move to a safe distance.  
Disconnect the charging cable and close the  
flap.  
Identify the cause of the fault using the message  
displayed on the instrument panel.  
Traction Battery Fault  
Warning Light  
Seat Belt Reminder  
Warning Light  
Fixed, accompanied by the display of  
the message "Audible Warning System fault:  
Repair needed ".  
The audible warning system is in failure.  
The following driving aids may be disturbed or  
unavailable:  
Fixed, combined with the Service  
warning lamp, accompanied by the display of a  
message.  
Fixed or flashing, accompanied by an  
increasing audible signal.  
A seat belt has not been fastened or has been  
unfastened (depending on version).  
The traction battery has a fault.  
-
-
-
-
Road signs recognition.  
Active Safety Brake/Collision Risk Alert.  
Lane keeping assist.  
Anti-lock Brake System  
(ABS) Warning Light  
System Malfunction  
Warning Light  
Fixed.  
Driver Attention Warning.  
Fixed.  
Fixed, accompanied by the message  
"Parking brake fault".  
Automatic release of the electric parking brake is  
unavailable.  
The anti-lock braking system has a fault.  
The vehicle retains conventional braking.  
Drive carefully at moderate speed.  
A fault involving the electric motor or traction  
battery has been detected.  
Service Warning Light  
Temporarily on, accompanied by the  
display of a message.  
78  
Dashboard Instruments And Control  
The system activates and brakes the vehicle  
momentarily to reduce the speed of collision with  
the vehicle in front.  
Electronic Brake Force  
Distribution (EBFD)  
Warning Light  
Electric Park Brake  
Warning Light  
3
Fixed, accompanied by the display of a  
message.  
The system has been deactivated via the touch  
screen.  
Fixed, accompanied by the message  
"Parking brake fault".  
Fixed.  
The vehicle cannot be immobilised with the  
engine running.  
If manual application and release commands are  
not working, the electric parking brake control is  
faulty.  
The automatic functions must be used at all  
times and are automatically reactivated in the  
event of a fault with the control.  
The electronic brake force distribution (EBFD)  
system is faulty.  
Fixed, accompanied by a message and an  
audible signal.  
The system has a fault.  
Electric Park Brake  
Applied Light  
Fixed, accompanied by the display of the  
message "Driving Assistance Sensor blind:  
Clean sensor, see User Manual ".  
The sensor is masked.  
Stop as soon as it is safe to do so and switch off  
the ignition.  
Clean the front camera.  
Fixed.  
Fixed, accompanied by the  
message "Parking brake fault".  
The electric parking brake is faulty: manual and  
automatic functions may not be working.  
When stationary, to immobilise the vehicle:  
The "automatic application" (on switching off  
the engine) and "automatic release" (on  
acceleration) functions are deactivated.  
If automatic application/release is no longer  
possible:  
Fixed.  
If these warning lamps come on after the engine  
is switched off and then restarted.  
► Pull the electric parking brake control and  
hold it for approximately 7 to 15 seconds,  
until the indicator lamp lights up on the  
instrument panel.  
► Start the engine.  
► Use the control to apply the electric parking  
brake.  
Fixed.  
The system is deactivated temporarily because  
the driver and/or front passenger (depending on  
version) has been detected as present but the  
corresponding seat belt has not been fastened.  
► Take your foot fully off the brake pedal.  
► Hold the control pressed in the release  
direction for between 10 and 15 seconds.  
If this procedure does not work, secure the  
vehicle:  
► Park on a level surface.  
► With a manual gearbox, engage a gear.  
► Release the control.  
► Depress and hold the brake pedal.  
Electronic Stability  
Control (ESC) / Traction  
Control System (TC)  
Active Warning Light  
► Pull the control in the application direction for  
2 seconds.  
Active Emergency  
Braking Warning Light  
Flashing.  
► Release the control and the brake pedal.  
Flashing.  
79  
Dashboard Instruments And Control  
ESC/TC system regulation is activated in the  
event of a loss of grip or trajectory.  
AdBlue® Warning Light  
On for around 30 seconds when starting  
the vehicle, accompanied by a message  
indicating the driving range.  
The driving range is between 1,500 and 500  
miles (2,400 and 800 km).  
Top up the AdBlue®.  
Fixed, accompanied by the display of the  
message "Driving Assistance Sensor blind:  
Clean sensor, see User Manual ".  
The sensor is masked.  
Stop as soon as it is safe to do so and switch off  
the ignition.  
Fixed.  
ESC/TC system has a fault.  
Electronic Stability  
Clean the front camera.  
Control (ESC) / Traction  
Control System (TC) OFF  
Warning Light  
Service Lane Keep Assist  
Warning Light  
Fixed, on switching on the ignition,  
accompanied by an audible signal and a  
message indicating the driving range.  
The driving range is between 500 and 62 miles  
(800 and 100 km).  
The system has a fault.  
Promptly top up the AdBlue®.  
Fixed.  
Flashing, accompanied by an audible  
signal and a message indicating the driving  
range.  
The driving range is less than 62 miles (100 km).  
You must top up the AdBlue® to avoid engine  
starting being prevented.  
The system is deactivated.  
Low Fuel Warning Light  
The ESC/TC system is reactivated automatically  
when the vehicle is restarted, and at speeds  
above approximately 31 mph (50 km/h).  
At speeds below 31 mph (50 km/h), it can be  
reactivated manually.  
Fixed, with the blocks lit flashing,  
accompanied by an audible signal (with the  
matrix instrument panel) or Fixed, with the  
reserve level shown in red, accompanied by an  
audible signal and the display of a message  
(except with the matrix instrument panel).  
When it first comes on, there are approximately  
5 litres of fuel remaining in the tank (reserve).  
Until the fuel level is topped up, this alert will  
be repeated every time the ignition is switched  
on, with increasing frequency as the fuel level  
decreases and approaches zero.  
Flashing, accompanied by an audible  
signal and a message indicating that starting is  
prevented.  
The AdBlue® tank is empty: the legally required  
engine immobiliser system prevents the engine  
from starting.  
To restart the engine, top up the AdBlue®.  
It is essential to add at least 10 litres of AdBlue®  
to the tank.  
Lane Keep Assist (LKA)  
Warning Light  
Flashing.  
You are about to cross a broken lane marking  
without operating the direction indicators.  
The system is activated, then corrects the  
trajectory if it detects a risk of unintentionally  
crossing a line or hard shoulder (depending on  
version).  
Refuel without delay to avoid running out of fuel.  
Never drive until completely empty, as  
this could damage the emissions control and  
injection systems.  
Fixed when the ignition is  
switched on, accompanied by an audible signal  
and a message.  
Fixed.  
A malfunction of the SCR (Selective Catalytic  
Reduction) emissions control system has been  
detected.  
The system has been automatically deactivated  
or placed on standby.  
This alert disappears once the exhaust  
emissions return to normal levels.  
80  
Dashboard Instruments And Control  
Flashing AdBlue® warning lamp  
on switching on the ignition, with the Service  
and Engine self-diagnostics warning lamps on  
fixed, accompanied by an audible signal and a  
message indicating the driving range.  
Depending on the message displayed, it is  
possible to drive for up to 685 miles (1,100 km)  
before the engine immobiliser is triggered.  
Fixed.  
Under-inflation warning lamp flashing  
then fixed and Service warning lamp fixed.  
The tire pressure monitoring system is faulty.  
Under-inflation detection is no longer monitored.  
Check the tire pressures as soon as possible.  
3
A major engine fault has been detected.  
Engine Preheating  
Warning Light  
Temporarily on (up to approximately 30  
seconds in severe weather conditions).  
When switching on the ignition, if the weather  
conditions and the engine temperature make it  
necessary.  
Wait until the warning lamp goes off before  
starting.  
When the warning lamp goes off, starting will  
occur immediately if you press and hold:  
Traffic Sign Recognition  
(TSR) Warning Light  
Flashing AdBlue® warning lamp  
on switching on the ignition, with the Service  
and Engine selfdiagnostics warning lamps on  
fixed, accompanied by an audible signal and a  
message indicating that starting is prevented.  
The engine immobiliser prevents the engine from  
restarting (the permitted driving limit has been  
exceeded after confirmation of a malfunction of  
the emissions control system).  
Temporarily on.  
The overspeed alert sound has been  
deactivated.  
Fixed, accompanied by the display of a  
message and an audible signal.  
The system has a fault.  
-
-
the clutch pedal with a manual gearbox.  
the brake pedal with an automatic gearbox.  
If the engine does not start, make the engine  
starting request again, while keeping your  
foot on the pedal.  
Fixed, accompanied by the display of the  
message "Driving Assistance Sensor blind:  
Clean sensor, see User Manual ".  
The sensor is masked.  
Stop as soon as it is safe to do so and switch off  
the ignition.  
Engine Check-  
Malfunction Indicator  
(MIL) Warning Light  
Tire Pressure Monitoring  
System (TPMS) Warning  
Light  
Clean the front camera.  
Flashing.  
The engine management system has a fault.  
There is a risk that the catalytic converter will be  
destroyed.  
Parking sensors Warning  
Light  
Fixed, accompanied by an audible signal  
and a message.  
Fixed.  
The emissions control system has a fault.  
The warning lamp should go off when the engine  
is started.  
The pressure in one or more tires is too low.  
Check the pressure of the tires as soon as  
possible.  
Flashing.  
The system detects an obstacle.  
Reinitialise the detection system after adjusting  
the pressure.  
Fixed, accompanied by the display of a  
message and an audible signal.  
The system has a fault.  
Fixed.  
A minor engine fault has been detected.  
81  
Dashboard Instruments And Control  
The function is regulating the speed of the  
vehicle.  
The vehicle is being braked; the brake lamps  
come on during the descent.  
Particle Filter Warning  
Light  
Fixed, accompanied by the display of the  
message "Parking Assistance Sensor blind:  
Clean sensor, see User Manual ".  
The sensor is masked.  
Stop as soon as it is safe to do so and switch off  
the ignition.  
Clean the front and/or rear sensors.  
Fixed, accompanied by an audible signal  
and a message about the risk of particle filter  
blockage.  
The particle filter is nearing saturation.  
As soon as traffic conditions allow, regenerate  
the filter by driving at a speed of at least 37 mph  
(60 km/h), with an engine speed of above 2,500  
rpm, until the warning lamp goes off.  
Turn Signal Indicator  
Light  
Tortoise mode Warning  
Light  
Flashing with audible signal.  
The direction indicators are on.  
Fixed.  
Stop-Start Active Indicator  
Light  
Fixed, accompanied by an audible signal  
and a message indicating that the additive level  
in the particle filter is too low.  
The low level in the additive tank has been  
reached.  
The state of charge of the traction battery is  
critical.  
The engine power gradually decreases.  
You must put the vehicle on charge.  
Fixed.  
When the vehicle stops, the Stop & Start system  
puts the engine into STOP mode.  
Pedestrian Horn Warning  
Light  
Automatic Low Beam  
Indicator Light  
Flashing temporarily.  
STOP mode is momentarily unavailable or  
START mode is automatically triggered.  
Fixed.  
The lamps are on.  
Fixed.  
Horn fault detected.  
Ready To Drive Indicator  
Light  
Hill Assist Descent  
Control Warning Light  
Water in Fuel Filter  
Warning Light  
Fixed.  
Fixed, accompanied by an audible signal  
when it comes on.  
The vehicle is ready to drive and the thermal  
comfort systems are available.  
The indicator lamp goes out upon reaching a  
speed of approximately 3 mph (5 km/h) and  
lights up again when the vehicle stops moving.  
The lamp will go out when you switch off the  
motor and exit the vehicle.  
Fixed.  
The system has been activated, but the  
conditions for regulation are not met (gradient,  
speed too high, gear engaged).  
The Diesel fuel filter contains water.  
Risk of damaging the fuel injection system!  
Flashing.  
82  
Dashboard Instruments And Control  
Air distribution  
Automatic High Beam  
Indicator Light  
Climate controls  
3
: to windscreen and front door windows  
: to head area via adjustable air vents  
: to foot well and windscreen  
AC On-Off Control  
Fixed.  
The function has been activated via the vehicle’s  
configuration menu.  
The lighting control stalk is in the "AUTO"  
position.  
All combinations are possible.  
Cooling A/C  
Press A/C to switch on cooling. The LED in the  
button illuminates to indicate activation. Cooling  
is only functional when the engine is running and  
fan is switched on.  
Press A/C again to switch off cooling.  
The air conditioning system cools and  
dehumidifies (dries) as soon as the outside  
temperature is slightly above the freezing point.  
Therefore, condensation may form and drip from  
under the vehicle.  
High Beam Indicator Light  
Fixed.  
The lamps are on.  
Front Fog Warning Lights  
Controls for:  
n
-
-
temperature  
Fixed.  
The front foglamps are on.  
If no cooling or drying is required, switch off the  
cooling system for fuel saving reasons.  
air distribution  
,
and  
-
-
fan speed  
cooling A/C  
air recirculation q  
-
-
heated rear window  
or heated exterior  
mirrors  
.
Temperature  
n
Adjust the temperature by turning  
desired temperature.  
HI : warm  
to the  
LO : cold  
Heating will not be fully effective until the engine  
has reached normal operating temperature.  
83  
Dashboard Instruments And Control  
Maximum AC On-Off  
Control  
Demisting and defrosting  
the windows  
Recirculation control  
Press q to activate air recirculation mode.  
The LED in the button illuminates to indicate  
activation.  
Briefly open the windows so that hot air can  
disperse quickly.  
-
-
Set fan speed  
to highest level.  
Press q again to deactivate air recirculation  
mode.  
n
-
-
-
-
Switch on cooling A/C.  
Set temperature controller  
level.  
to warmest  
Press q for air recirculation system on.  
-
-
Switch on cooling A/C, if required.  
Warning  
Press  
for air distribution.  
Switch on heated rear window  
exterior mirrors  
or heated  
The exchange of fresh air is reduced in air  
recirculation mode.  
In operation without cooling, the air humidity  
increases, so the windows may mist up from  
inside.  
The quality of the passenger compartment air  
deteriorates, which may cause the occupants  
to feel drowsy.  
.
n
Set temperature control  
to coldest level.  
-
-
Switch on heated windscreen  
.
-
-
Set fan speed  
Open all vents.  
to highest level.  
Open side air vents as required and direct  
them towards the door windows.  
NOTE:  
If the settings for demisting and defrosting are  
selected, an Autostop may be inhibited.  
If the settings for demisting and defrosting are  
selected while the engine is in an Autostop, the  
engine will restart automatically.  
In warm and very humid ambient air conditions,  
the windscreen may mist up from outside when  
cold air is directed towards it. If windscreen mists  
up from outside, activate windscreen wiper and  
deactivate  
.
84  
Dashboard Instruments And Control  
Press q again to deactivate air recirculation  
mode.  
: to head area via adjustable air vents  
: to foot well and windscreen  
Heating and ventilation  
system  
3
Warning  
The exchange of fresh air is reduced in air  
recirculation mode.  
In operation without cooling, the air humidity  
increases, so the windows may mist up from  
inside.  
All combinations are possible.  
Fan speed  
The quality of the passenger compartment air  
deteriorates, which may cause the occupants  
to feel drowsy.  
In warm and very humid ambient air conditions,  
the windscreen may mist up from outside when  
cold air is directed towards it. If windscreen mists  
up from outside, activate windscreen wiper and  
Adjust the air flow by turning  
speed.  
clockwise : increase  
anticklockwise : decrease  
to the desired  
Controls for:  
deactivate  
.
n
-
temperature  
Demisting and defrosting  
Air recirculation system  
-
-
air distribution  
fan speed  
,
, and  
air recirculation q  
-
-
heated rear window  
mirrors  
or heated exterior  
Temperature  
n
Adjust the temperature by turning  
desired temperature.  
HI: warm  
to the  
LO: cold  
Heating will not be fully effective until the engine  
has reached normal operating temperature.  
Press q to activate air recirculation mode.  
The LED in the button illuminates to indicate  
activation.  
-
-
Press  
: the air distribution is directed  
Air distribution  
towards the windscreen.  
n
Set temperature controller  
level.  
to warmest  
: to windscreen and front door windows  
85  
Dashboard Instruments And Control  
Basic setting for maximum comfort:  
-
-
Set fan speed  
to highest level.  
-
-
-
Press AUTO, the air distribution and fan  
speed are regulated automatically.  
Switch on heated rear window and exterior  
mirrors  
mirrors  
or switch on heated exterior  
.
Open all air vents to allow optimised air  
distribution in automatic mode.  
-
-
Switch on heated windscreen  
.
Open side air vents as required and direct  
them towards the door windows.  
Air conditioning must be activated for optimal  
cooling and demisting. Press A/C to switch  
on air conditioning. The LED in the button  
indicates activation.  
-
-
-
-
demisting and defrosting  
cooling A/C  
Automatic AC control  
The dual zone climate control allows different  
temperatures for driver side and front passenger  
side.  
In automatic mode, temperature, fan speed and  
air distribution are regulated automatically.  
automatic mode AUTO  
-
Set the preselected temperatures for driver  
and front passenger using the left and right  
rotary ring. Recommended temperature is 22  
°C.  
dual zone temperature synchronisation  
MONO  
-
heated rear window  
mirrors  
or heated exterior  
Press successively AUTO to select the desired  
automatic settings:  
-
fan speed  
+
-
Activated functions are indicated by the LED in  
the respective control.  
The electronic climate control system is only fully  
operational when the engine is running.  
-
-
Soft Auto for a soft and silent air distribution.  
Auto for thermal comfort and silent air  
distribution.  
-
Auto Fast for a dynamic and efficient air  
distribution.  
Automatic mode AUTO  
Manual settings  
Climate control system settings can be changed  
by activating the following functions:  
Fan speed  
+
-
Controls for:  
air recirculation q  
-
-
-
air distribution  
rocker switch for adjusting the temperature  
on driver side and front passenger side  
86  
Dashboard Instruments And Control  
Dual zone temperature synchronisation  
MONO  
: to head area and rear seats via ad-  
justable air vents  
3
Press MONO to link passenger side temperature  
setting to the driver side / to remove the linking  
of the passenger side temperature setting to  
the driver side. The passenger side temperature  
setting is linked to the driver side if the LED in  
the button MONO is not illuminated.  
: to front and rear foot well  
: to windscreen and front door win-  
dows, to head area and rear seats  
via adjustable air vents, to front and  
rear foot well  
Air conditioning A/C  
Combinations of different air distribution options  
can be select by pressing  
sucessively.  
To return to automatic air distribution, press  
AUTO.  
Press  
+ to increase or  
- to decrease the  
Temperature preselection  
air flow.  
To return to automatic mode, press AUTO.  
Air distribution  
Set the preselected temperatures separately  
for the driver and the front passenger to the  
desired value using the left and right switch for  
adjustusting the temperature.  
Press A/C to switch on cooling.  
Cooling is only functional when the engine is  
running and climate control fan is switched on.  
Press A/C again to switch off cooling.  
The air conditioning system cools and  
dehumidifies (dries) when outside temperature is  
above a specific level.  
Therefore condensation may form and drip from  
under the vehicle.  
If no cooling or drying is required, switch off the  
cooling system for fuel saving reasons.  
Recommended temperature is 22 °C.  
Temperature is indicated in the display beside  
the switches for adjusting the temperature.  
If the minimum temperature Lo is set, the climate  
control system runs at maximum cooling, if  
cooling A/C is switched on.  
Press  
sucessively until the desired direction  
If the maximum temperature Hi is set, the  
climate control system runs at maximum heating.  
of the air distribution is displayed:  
NOTE:  
: to windscreen and front door win-  
dows  
If A/C is switched on, reducing the set cabin  
temperature can cause the engine to restart from  
an Autostop or inhibit an Autostop.  
87  
Dashboard Instruments And Control  
Manual air recirculation  
Demisting and defrosting the windows  
Deactivation of electronic climate control  
system  
Press  
- subsequently until the electronic  
climate control system is deactivated.  
Temperature Control  
The temperature preconditioning allows to heat  
the vehicle's interior and to ventilate the vehicle's  
interior with ambient air.  
The temperature preconditioning can be  
programmed using the Infotainment system.  
This function is also available via the  
MYPEUGEOT APP.  
NOTE:  
Press q to activate the air recirculation mode.  
q is shown in the display to indicate activation.  
Press q again to deactivate recirculation mode.  
-
-
Press  
to indicate activation.  
. The LED in the button illuminates  
The temperature preconditioning is only  
activated if the ignition is off and the vehicle is  
locked.  
Air conditioning and automatic mode are  
automatically switched on. The LED in the  
button A/C illuminates, AUTO is shown in the  
display.  
If the charging level of the high voltage battery  
is below 30%, the temperature preconditioning is  
not activated.  
When the vehicle is plugged in, battery charging  
takes precedence over pre-conditioning.  
Consequently, it can only be activated if the  
battery is charged above a threshold fixed at  
80%.  
If a recurrent heating / ventilation is programmed  
and two heating / ventilation procedures are  
carried out without operating the vehicle, the  
programming is deactivated.  
Warning  
The exchange of fresh air is reduced in air  
recirculation mode.  
In operation without cooling, the air humidity  
increases, so the windows may mist up from  
inside.  
The quality of the passenger compartment air  
deteriorates, which may cause the occupants  
to feel drowsy.  
-
Temperature and air distribution are set  
automatically and the fan runs at high speed.  
-
-
-
Switch on heated rear window  
Switch on heated windscreen  
To return to previous mode, press  
.
again.  
NOTE:  
In warm and very humid ambient air conditions,  
the windscreen may mist up from outside, when  
cold air is directed towards it. If windscreen mists  
up from outside, activate windscreen wiper and  
If is pressed while the engine is running,  
an Autostop will be inhibited until  
again.  
Setting timer  
NOTE:  
is pressed  
If  
is pressed while the engine is in an  
Several timers can be programmed and saved.  
It is recommended to programme temperature  
preconditioning with the vehicle plugged in, in  
order to optimise the long-term perfomance of  
the high voltage battery.  
deactivate  
.
Autostop, the engine will restart automatically.  
88  
Dashboard Instruments And Control  
Direct the flow of air by tilting and swivelling the  
slats.  
Navigation system / Multimedia  
Air vents  
3
To close the vent, swivel the slats outwards.  
At least two air vents must be open while cooling  
is on.  
Adjustable air vents  
Air vents in the instrument panel  
Warning  
Do not attach any objects to the slats of  
the air vents. Risk of damage and injury in  
case of an accident.  
Press MENU on the climate control panel or  
touch  
on the Info Display to open the climate  
settings.  
Air vent in the glovebox  
n
Touch  
and then select the preconditioning  
settings menu.  
Select + to define a new timer or touch  
to a timer to edit it.  
next  
Activate the timer.  
To delete a timer, select the desired timer and  
Z
press  
at the lower left corner of the screen.  
Direct the flow of air by tilting and swivelling the  
slats.  
To close the vent, swivel the slats inwards.  
The heating / ventilation procedure starts  
approx. 45 minutes before the programmed time  
when the vehicle is plugged in, or 20 minutes  
before the programmed time when it is not  
plugged in, and is maintained ten minutes after  
it.  
Outer air vents in the instrument panel  
Turn the slider up or down in order to close or  
open the air vent.  
89  
Dashboard Instruments And Control  
Rear air vents in the ceiling  
Type B  
Fixed air vents  
Additional air vents are located beneath the  
windscreen, the door windows and in the foot  
wells.  
Display  
Instrument cluster  
Pages  
The Driver Information Centre is located on the  
instrument cluster.  
Depending on the version, different instrument  
clusters are available.  
In addition to warning lights, gauges and  
indicators, the following information is available:  
To activate the distribution of climatised / heated  
E
-
-
-
-
-
-
-
trip odometer  
air via the rear air vents, press  
.
gear shift indication  
service information  
vehicle and warning messages  
driver assistance messages  
pop-up messages  
infotainment information  
Press the button to scroll through several on-  
board pages or to close a pop-up message.  
Messages are indicated in the Driver Information  
Centre, in some cases together with a warning  
chime.  
Type A  
Press to confirm a message.  
Vehicle and service messages  
Direct the flow of air by tilting and swivelling the  
slats.  
The vehicle messages are displayed as text.  
Follow the instructions given in the messages.  
Adjust the air flow to select the desired speed.  
Messages in the Info Display  
Some important messages may appear  
additionally in the Info Display. Some messages  
only pop-up for a few seconds.  
90  

Related Topics

Instrument Panel / Instrument Cluster
Warning, lights, indicators and messages
Climate controls
Display

Popular Owner Manuals

Audi
BMW
Citroen
Ford
Honda
Peugeot

Latest Owner Manuals

First Generation (2020-2026) Audi Rs Q8 SUV First Generation (2020-2026) Audi Rs Q8 SUV
Second Generation (2016-2024) Audi R8 2 Door Second Generation (2016-2024) Audi R8 2 Door
Second Generation (2013-2020) Ford Fusion 4 Door Second Generation (2013-2020) Ford Fusion 4 Door
First Generation (2006-2012) Ford Fusion 4 Door First Generation (2006-2012) Ford Fusion 4 Door
Third Generation (2016-2023) Ford Galaxy Van Third Generation (2016-2023) Ford Galaxy Van
Second Generation (2007-2015) Ford Galaxy Van Second Generation (2007-2015) Ford Galaxy Van