Get TECHNOLOGY on BOARD Guide for Peugeot Partner Van 2008-2014

EMERGENCY OR ASSISTANCE CALL

9.1

EMERGENCY OR ASSISTANCE CALL

In an emergency, press this button for more than

2 seconds. Flashing of the green LED and a voice

message conﬁrm that the call has been made to the

PEUGEOT Emergency team*.

Press this button for more than 2 seconds to request

assistance if the vehicle breaks down.

A voice message conﬁrms that the call has been made*.

Pressing this button again immediately cancels the request.

The cancellation is conﬁrmed by a voice message.

Pressing this button again immediately cancels the request. The green

LED goes off.

A press (at any time) of more than 8 seconds on this button, cancels the

request.

OPERATION OF THE SYSTEM

The green LED remains on (without ﬂashing) when communication is

established. It goes off at the end of communication.

When the ignition is switched on, the green

LED comes on for 3 seconds indicating that

the system is operating correctly.

This call is dealt with by the PEUGEOT Emergency team which receives

locating information from the vehicle and can send a detailed alert to the

appropriate emergency services. In countries in which the team is not

operational, or when the locating service has been expressly declined,

the call is dealt with directly by the emergency services (112) without the

vehicle location.

If the orange LED ﬂashes: there is a system

fault.

If the orange LED is on continuously: the

backup battery must be replaced.

In either case, contact a PEUGEOT dealer.

If you purchased your vehicle outside the PEUGEOT dealer network,

we invite you to have a dealer check the conﬁguration of these services

and, if desired, modiﬁed to suit your wishes. In a multi-lingual country,

conﬁguration is possible in the ofﬁcial national language of your choice.

If an impact is detected by the airbag control unit, and

independently of the deployment of any airbags, an emergency

call is made automatically.

For technical reasons, particularly to improve the quality of PEUGEOT

CONNECT services to customers, the manufacturer reserves the right to

carry out updates to the vehicle's on-board telematic system.

* These services are subject to conditions and availability.

Consult a PEUGEOT dealer.

9.2

Peugeot Connect Navigation (RNEG)

MULTIMEDIA AUDIO SYSTEM / BLUETOOTH^®TELEPHONE

SATELLITE NAVIGATION SYSTEM FOR EUROPE BY SD CARD

CONTENTS

p.

9.4

9.5

9.6

9.9

01 First steps

02 Steering mounted controls

03 General operation

04 Navigation - Guidance

05 Traffic information

06 Radio

07 Music media players

08 Bluetooth^®telephone

09 Configuration

The Peugeot Connect Navigation (RNEG) is protected

in such a way that it will only operate in your vehicle.

p. 9.17

p. 9.19

p. 9.20

p. 9.23

p. 9.26

p. 9.27

p. 9.28

p. 9.32

For safety reasons, the driver must carry out operations

which require prolonged attention while the vehicle is

stationary.

When the engine is switched off and to prevent

discharging of the battery, the Peugeot Connect

Navigation (RNEG) switches off following the activation

of the Energy Economy mode.

10 Trip computer

11 Screen menu map

Frequently asked questions

9.3

01

FIRST STEPS

Engine not running:

-

Short press: on/off.

Long press: pause with CD

play, mute for radio.

Long press: audio settings: front/rear

fader, left/right balance, bass/treble,

musical ambience, loudness, automatic

volume, reinitialise settings.

Selection dial for the

screen display and

according to the menu.

Access to the

"SETUP" menu.

Engine running:

-

Short press: contextual

menu or conﬁrm.

Long press: contextual

menu speciﬁc to the list

displayed.

Short press: pause with CD

play, mute for radio.

Long press: reinitialise the

system.

Access to the

Long press: GPS

coverage and

demonstration

mode.

Radio Menu.

Display the list of

stations.

Access to the

Music Menu.

Display tracks.

Access to the Phone

Menu. Display the list of

calls.

-

Eject CD.

Adjust volume (each source

is independent, including

navigation messages and

alerts).

Select previous/next radio

station.

Select previous CD or MP3

track.

Select previous/next line in

a list.

Buttons 1 to 6:

Select previous/next radio

station in the list.

Select a pre-set radio

station.

Select previous/next MP3

folder.

Long press: pre-set the

current station.

Select previous/next page in

a list.

Access to the "MODE" menu.

Select successive display of:

Radio, Map, NAV (if navigation in progress),

Telephone (if conversation in progress), Trip

computer.

Access to the

Reader for

navigation SD

card only.

Access to the

ESC: abandon current operation.

Navigation

Menu. Display

recent

Trafﬁc Menu.

Display the current

trafﬁc alerts.

destinations.

Long press: Black screen (DARK).

9.4

STEERING MOUNTED CONTROLS

02

RADIO: change to the next radio station

in the list.

Long press: automatic search for a

higher frequency.

CD: select the next track.

RADIO: select the previous/next preset

station.

Select the next entry in the address book.

CD: continuous press: fast forward play.

Volume increase.

Mute: press the volume

increase and decrease

buttons simultaneously.

Restore the sound by

pressing one of the two

volume buttons.

Change the audio source.

Start a call from the address book.

Call/End call on the telephone.

Press for more than 2 seconds: access to

the address book.

Volume decrease.

RADIO: change to the previous radio

station in the list.

Long press: automatic search for a

lower frequency.

CD: select the previous track.

CD: continuous press: fast reverse.

9.5

03 GENERAL OPERATION

Press the MODE button several times in succession for access to the following menus:

RADIO / MUSIC MEDIA PLAYERS

FULL SCREEN MAP

TELEPHONE

(If a conversation is in progress)

NAVIGATION

(If guidance is in progress)

TRIP COMPUTER

SETUP:

system language*, date and time*, display,

vehicle settings*, unit and system settings, "Demo

mode".

TRAFFIC:

TMC information and messages.

* Available according to model.

For cleaning the screen, the use of a soft, non-abrasive cloth

(spectacles cloth) is recommended, with no additional product.

For a detailed global view of the menus available, refer to the

"Screen menu map" section.

9.6

03 GENERAL OPERATION

DISPLAY ACCORDING TO THE CONTEXT

NAVIGATION (IF GUIDANCE IS IN

PROGRESS):

TRIP COMPUTER:

A press on the OK dial gives access to

short-cut menus according to the display

on the screen.

Abort guidance

Repeat advice

Block road

Route info

Show destination

Trip info

Alert log

1

Status of functions

1

TELEPHONE:

2

End call

1

Hold call

1

Route type

3

Dial

1

Avoid

DTMF-Tones

1

Satellites

Private mode

1

Zoom/Scroll

Voice advice

Route options

2

Micro off

1

9.7

GENERAL OPERATION

03

DISPLAY ACCORDING TO THE CONTEXT

MUSIC MEDIA PLAYERS:

RADIO:

In FM mode

FULL SCREEN MAP:

Trafﬁc info (TA)

Abort guidance/Resume guidance

1

Play options

Trafﬁc info (TA)

RDS

Set destination

POIs nearby

Position info

Map settings

Zoom/Scroll

1

2

1

Normal order

2

Random track

Radiotext

Regional prog.

AM

2

Repeat folder

2

Scan

2

Select music

In AM mode

TA

1

2

Refresh AM list

FM

9.8

04

NAVIGATION - GUIDANCE

Insert the SD card in the front panel reader and leave it there to use the

Navigation functions.

The navigation SD card data must not be modiﬁed.

Map data updates are available from PEUGEOT dealers.

SELECTING A DESTINATION

1

4

Select the "Address input" function

and press the dial to conﬁrm.

Press the NAV button.

Address input

5

Once the country has been selected,

turn the dial and select the town

function. Press the dial to conﬁrm.

The list of the last 20 destinations appears under the Navigation

Menu function.

2

3

6

Press the NAV button again or select

the Navigation Menu function and

press the dial to conﬁrm.

Select the letters of the town one

by one conﬁrming each time by

pressing the dial.

Navigation Menu

Select the "Destination input"

function and press the dial to

conﬁrm.

A pre-set list (by entering the ﬁrst few letters) of the towns in the

country selected can be accessed via the LIST button on the virtual

keypad.

Destination input

9.9

04

NAVIGATION - GUIDANCE

7

9

Turn the dial and select OK.

Press the dial to conﬁrm.

Then select "Start route guidance"

and the press the dial to conﬁrm.

Start route guidance

To speed up the process, the post code can be entered directly

after selecting the "Postal code" function.

Use the virtual keypad to enter the letters and digits.

Select the route type:

"Fast route", "Short route" or "Optimized route" and press the dial

8

to conﬁrm.

Repeat steps 5 to 7 for the "Street"

and "House number" functions.

It is also possible to select a destination via "Choose from address

book" or "Choose from last destinations".

Choose from address book

Choose from last destinations

Select the "Save to address book" function to record the address

entered in a directory ﬁle. Press the dial to conﬁrm the selection.

Peugeot Connect Navigation allows up to 500 contact ﬁles to be

recorded.

Map settings

You can zoom in / zoom out on the map using the dial.

It is possible to move the map or select its orientation via the short-

cut menu of the FULL SCREEN MAP.

Press MODE until the map is displayed full screen. Press the dial

then select "Map settings". Select "2.5D Map" or "2D Map" and in

the latter case, select "North Up" or "Heading Up".

During guidance, pressing this button

repeats the last guidance instruction.

To clear a destination; from steps 1 to 3, select "Choose from last destinations".

A long press on one of the destinations displays a list of actions from which you can select:

Delete entry

Delete list

9.10

04

NAVIGATION - GUIDANCE

SETTING AND NAVIGATING TO MY

"HOME ADDRESS"

4

To be set as the "Home address", an address must ﬁrst be

entered in the address book, for example from "Destination

input" / "Address input" then "Save to address book".

Select your home address and conﬁrm.

Then select "Edit entry" and conﬁrm.

Edit entry

1

2

3

Press the NAV button twice to display

the Navigation Menu.

5

Navigation Menu

Select "Set as home address" and

conﬁrm to save.

Select "Destination input" and conﬁrm.

Then select "Choose from address

book" and conﬁrm.

Set as "Home address"

Destination input

To start navigation towards "Home address", press NAV twice

to display the Navigation Menu, select "Destination input" and

conﬁrm.

Select "Address book" and conﬁrm.

Then select "Search entry (complete

address book)" and conﬁrm.

Then select "Navigate HOME" and conﬁrm to start guidance.

Address book

9.11

04

NAVIGATION - GUIDANCE

The route selected by the Peugeot Connect Navigation system depends

directly on the route options.

Changing these options may change the route completely.

ROUTE OPTIONS

1

2

3

5

Select the "Route dynamics"

function.

Press the NAV button.

This function gives access to the

"Trafﬁc independent" or "Semi-

dynamic" options.

Route dynamics

Press the NAV button again or select

the Navigation Menu function and

press the dial to conﬁrm.

6

Select the "Avoidance criteria"

function. This function provides

access to the AVOID options

(motorways, toll roads, ferries).

Navigation Menu

Select the "Route options" function

and press the dial to conﬁrm.

Avoidance criteria

Route options

7

Turn the dial and select the

"Recalculate" function to take into

account the route options selected.

Press the dial to conﬁrm.

4

Select the "Route type" function

and press the dial to conﬁrm. This

function allows you to change the

route type.

Recalculate

Route type

9.12

04

NAVIGATION - GUIDANCE

Stopovers can be added to the route once the destination has been

selected.

ADDING A STOPOVER

1

2

3

4

5

Enter a new address, for example.

Press the NAV button.

Address input

6

Press the NAV button again or select

Once the new address has been

entered, select OK and press the dial

to conﬁrm.

the Navigation Menu function and

press the dial to conﬁrm.

Navigation Menu

OK

7

Select "Recalculate" and press the

dial to conﬁrm.

Select the "Stopovers" function and

press the dial to conﬁrm.

Stopovers

Recalculate

Select the "Add stopover" function

(5 stopovers maximum) and press

the dial to conﬁrm.

The stopover must be completed or deleted in order for the

guidance to continue to the next destination. Otherwise, the

Peugeot Connect Navigation will always return you to the previous

stopover.

Add stopover

9.13

04

NAVIGATION - GUIDANCE

SEARCHING FOR POINTS OF

INTEREST (POI)

The points of interest (POI) indicate all of the service locations in the

vicinity (hotels, various businesses, airports...).

Select the "POI in city" function to

search for POIs in the city required.

Select the country then enter the

name of the city using the virtual

keypad.

1

2

3

4

6

Press the NAV button.

POI in city

Press the NAV button again or select

the Navigation Menu function and

press the dial to conﬁrm.

A list of cities present in the country selected can be accessed via

the LIST button on the virtual keypad.

Navigation Menu

Select the "POI search" function and

press the dial to conﬁrm.

7

8

POI search

Select the "POI in country" function

to search for POIs in the country

required.

Select the "POI nearby" function to

search for POIs around the vehicle.

POI in country

POI nearby

Select the "POI near route" function

to search for POIs near the route.

Select the "POI near destination"

function to search for POIs near the

point of arrival of the route.

5

POI near route

POI near destination

9.14

This icon appears when several POIs are grouped

together in the same area. Zooming in on this icon

shows details of the POIs.

04 NAVIGATION - GUIDANCE

LIST OF PRINCIPAL POINTS OF INTEREST (POI)

Service station

Cinema

Airport

Theme parks

LPG station

Garage

Railway station

Bus station

Hospital

PEUGEOT

Port

Pharmacy

Police station

Motor racing circuit

Covered car park

Industrial estate

Supermarket

School

Car park

Post ofﬁce

Museum

Bank

Rest area

Hotel

Vending machine

Tennis court

Swimming pool

Golf course

Tourist information

Restaurant

Refreshment area

Automatic speed camera*

Red light camera*

Risk area*

Picnic area

Cafeteria

Winter sports resort

Theatre

* According to availability in the country.

9.15

04

NAVIGATION - GUIDANCE

To activate or deactivate vocal guidance, with guidance active and

the map displayed in the screen, press the dial and then select or

deselect "Voice advice".

NAVIGATION SETTINGS

Voice advice

1

2

3

The adjustment of the volume for the Risk Areas POIs is used only

during the transmission of an alert.

Press the NAV button.

5

6

Select the "POI categories on Map"

function to select the POIs to be

displayed on the map by default.

Press the NAV button again or select

POI categories on Map

the Navigation Menu function and

press the dial to conﬁrm.

Select "Set parameters for risk

areas" for access to the "Display

on map", "Visual alert" and "Sound

alert" functions.

Navigation Menu

Select the "Settings" function and

press the dial to conﬁrm.

Set parameters for risk areas

Settings

UPDATING POIs

4

Select the "Navi volume" function

and turn the dial to set the volume

of each voice synthesiser (trafﬁc

information, alert messages…).

The detailed procedure for updating POIs is available at the

following internet address: wipinforadars.co.uk.

This requires an SDHC (High Capacity) compatible reader.

Navi volume

9.16

TMC (Trafﬁc Message Channel) messages contain information on

trafﬁc and weather conditions, received in real time and transmitted to

the driver in the form of audible announcements and symbols on the

navigation map.

05 TRAFFIC INFORMATION

The navigation system can then suggest an alternative route to avoid a

trafﬁc problem.

CONFIGURE THE FILTERING AND

DISPLAY OF TMC MESSAGES

1

4

Select the "Geo. Filter" function and

press the dial to conﬁrm.

Press the TRAFFIC button.

Geo. Filter

5

Then select the radius of the ﬁlter in

The list of TMC messages appears under the Trafﬁc Menu sorted

in order of proximity.

miles (km) required in accordance

with the route, press the dial to

conﬁrm.

When all of the messages on the

route are selected, the addition of a

geographical ﬁlter is recommended

(within a radius of 3 miles (5 km) for

example) to reduce the number of

messages displayed on the map.

The geographical ﬁlter follows the

movement of the vehicle.

2

3

Press the TRAFFIC button again or

select the Trafﬁc Menu function and

press the dial to conﬁrm.

Trafﬁc Menu

Select the ﬁlter of your choice:

Messages on route

All warning messages

Only warnings on route

All messages

The ﬁlters are independent and their results are cumulative.

We recommend a ﬁlter on the route and a ﬁlter around the vehicle of:

-

2 miles (3 km) or 3 miles (5 km) for a region with heavy trafﬁc,

6 miles (10 km) for a region with normal trafﬁc,

30 miles (50 km) for long journeys (motorway).

The messages appear on the map

and on the list.

To exit, press ESC.

9.17

05

TRAFFIC INFORMATION

PRINCIPAL TMC SYMBOLS

RECEIVING TA MESSAGES

Black and blue triangle: general information, for example:

1

-

the station transmits TA messages.

the station does not transmit TA messages.

TA messages are not activated.

The TA (Trafﬁc Announcement) function gives priority to TA alert

messages. To operate, this function needs good reception of a

radio station transmitting this type of message. When a trafﬁc

report is transmitted, the current audio source (Radio, CD, ...) is

interrupted automatically to play the TA message. Normal playback

of the audio source resumes at the end of the transmission of the

message.

Red and yellow triangle: trafﬁc information, for example:

2

1

With the current audio source displayed

on the screen, press the dial.

2

3

The shortcut menu for the source appears and gives access to:

TA

Select Trafﬁc Announcements (TA)

and press the dial to conﬁrm and go

to the associated settings.

9.18

The external environment (hill, building, tunnel, underground car park...) may

interfere with the reception, including in RDS following mode. This phenomenon

is a normal result of the way in which radio waves are transmitted and does not

in any way indicate a failure of the audio equipment.

06

RADIO

SELECTING A STATION

RDS - REGIONAL MODE

1

When the current radio station is

displayed on the screen, press the

dial.

Press the RADIO button to display

the list of stations received locally

sorted in alphabetical order.

Select the station required by turning

the dial and press to conﬁrm.

The radio source short-cuts menu appears and provides access to

the following short-cuts:

2

TA

RDS

While listening to the radio, press one of the

buttons to select the previous or next station on

the list.

Radiotext

Regional prog.

AM

3

A long press of one of the buttons starts the

automatic search for a station with a lower or

higher frequency.

Select the function required and

press the dial to conﬁrm to gain

access to the corresponding settings.

RDS, if displayed, allows you to continue listening to the same

station by automatic retuning to alternative frequencies. However,

in certain conditions, coverage of an RDS station may not be

assured throughout the entire country as radio stations do not

cover 100 % of the territory. This explains the loss of reception of

the station during a journey.

Press one of the buttons on the numeric keypad for more than

2 seconds to store the current station.

Press the button on the numeric keypad to recall the stored radio

station.

9.19

07

MUSIC MEDIA PLAYERS

CD, MP3 / WMA CD

INFORMATION AND ADVICE

The Peugeot Connect Navigation will only play audio ﬁles with the

extension ".mp3" with a speed of between 8 Kbps and 320 Kbps

and the extension ".wma" with a speed of between 5 Kbps and

384 Kbps.

The MP3 format, an abbreviation of MPEG 1, 2 & 2.5 Audio Layer 3

and the WMA format, an abbreviation of Windows Media Audio and

the property of Microsoft, are audio compression standards which

permit the recording of several tens of music ﬁles on a single disc.

It also supports the VBR (Variable Bit Rate) mode.

No other type of ﬁle (.mp4, .m3u...) can be played.

In order to be able to play a recorded CDR or CDRW, when

recording it is preferable to select the ISO 9660 level 1, 2 or Joliet

standard.

If the disc is recorded in another format it may not be played

correctly.

It is recommended that the same recording standard is always

used for an individual disc, with as low a speed as possible

(4x maximum) for optimum sound quality.

It is advisable to restrict ﬁle names to 20 characters, without

using special characters (e.g.: " ? ; ù) to avoid any play or display

problems.

In the particular case of a multi-session CD, the Joliet standard is

recommended.

9.20

07

MUSIC MEDIA PLAYERS

SELECTING/PLAYING MUSIC

CD, MP3/WMA CD

1

4

5

6

Select the music source required:

CD, MP3/WMA CD. Press the dial to

conﬁrm. Play begins.

Press the MUSIC button.

Press the up or down button to select

the next/previous folder.

The list of tracks or MP3/WMA ﬁles appears under Music Menu.

2

3

Press the MUSIC button again or

select the Music Menu function and

press the dial to conﬁrm.

Press one of the buttons to select a

music track.

Press and hold one of the buttons for

fast forward or rewind play.

Music Menu

Select the "Select music" function

and press the dial to conﬁrm.

The playing and displaying of an MP3/WMA compilation may

depend on the recording programme and/or the settings used.

We recommend the ISO 9660 ﬁle standard.

Select music

9.21

07

MUSIC MEDIA PLAYERS

USING THE EXTERNAL INPUT (AUX)

AUDIO JACK-RCA CABLE NOT SUPPLIED

1

2

Connect the portable device (MP3/

WMA player…) to the RCA audio

sockets (white and red) using a

JACK/RCA audio cable.

Press the MUSIC button then

press it again or select the Music

Menu function and press the dial to

conﬁrm.

Music Menu

3

4

Select the "External device" function

and press the dial to activate it.

External device

Select the AUX music source and

press the dial to conﬁrm. Play begins

automatically.

The display and management of the controls is on the portable

device.

9.22

08 BLUETOOTH

^®

TELEPHONE

* The services available depend on the network, the SIM card and the

PAIRING A TELEPHONE /

FIRST CONNECTION

compatibility of the Bluetooth telephone used. Check the telephone

manual and with your network provider for details of the services

available to you.

3

For a ﬁrst connection, select

"Search phone" and press the dial to

conﬁrm. Then select the name of the

telephone.

For reasons of safety and because they require prolonged attention

on the part of the driver, the operations for pairing the Bluetooth

mobile telephone to the hands-free system of the Peugeot Connect

Navigation must be carried out with the vehicle stationary.

The ignition must be on.

Search phone

4

Enter the authentication code on the telephone.

The code to be entered is displayed on the screen

of the system.

Visit www.peugeot.co.uk for more information (compatibility, more help, ...).

Some telephones offer automatic reconnection of

the telephone every time the ignition is switched on.

A message conﬁrms the pairing.

1

2

Pairing can also be started from the telephone (refer to the

telephone instructions).

Activate the telephone's Bluetooth function

and ensure that it is "visible to all" (refer to the

telephone instructions).

Once the telephone has been connected, Peugeot Connect

Navigation can synchronise the address book and the call list.

This synchronisation may take a few minutes*.

To change the telephone connected,

press the PHONE button, then select

Phone Menu and press the dial to

conﬁrm.

Press the PHONE button.

9.23

08 BLUETOOTH

^®

TELEPHONE

* The services available depend on the network, the SIM card and the

compatibility of the Bluetooth telephone used. Check the telephone

manual and with your network provider for details of the services

available to you.

CONNECTING A TELEPHONE

For reasons of safety and because they require prolonged attention

on the part of the driver, the operations for pairing the Bluetooth

mobile telephone to the hands-free system of the Peugeot Connect

Navigation must be carried out with the vehicle stationary.

The ignition must be on.

Once the telephone has been connected, Peugeot Connect

Navigation can synchronise the address book and the call list.

This synchronisation may take a few minutes*.

1

Visit www.peugeot.co.uk for more information (compatibility, more

help, ...).

When a telephone is already

connected, to change it press the

PHONE button, then select Phone

Menu and press the dial to conﬁrm.

Activate the telephone's Bluetooth function

and ensure that it is "visible to all" (refer to the

telephone instructions).

The last telephone connected is reconnected

automatically.

1

2

Select "Connect phone". Select the

telephone and press to conﬁrm.

A message conﬁrms the connection.

Connect phone

Press the PHONE button.

The list of telephones connected previously (4 maximum) appears

on the multifunction screen. Select the telephone required for a

new connection.

9.24

08 BLUETOOTH

^®

TELEPHONE

RECEIVING A CALL

MAKING A CALL

1

2

3

1

Press the PHONE button.

An incoming call is announced by a ring and a superimposed

display on the multifunction screen.

The list of the last 20 calls made and received in the vehicle

appears under Phone Menu. You can select a number and press

the dial to make the call.

Select the "Yes" tab to accept or "No"

to refuse and conﬁrm by pressing

the dial.

Select the Phone Menu function and

press the dial to conﬁrm.

2

Phone Menu

Select "Dial number", then dial the

telephone number using the virtual

keypad.

Yes

No

Dial number

To hang up, press the PHONE button

or press the dial and select "End call"

then conﬁrm by pressing the dial.

It is also possible to select a number from the address book.

You can select "Dial from address book". The Peugeot Connect

Navigation can record up to 1 000 entries (telephone numbers).

Press the end of the steering mounted control for more than two

seconds to gain access to the address book.

End call

It is possible to make a call directly from the telephone; park the

vehicle as a safety measure.

Press the end of the steering mounted control to

accept the call or end the call in progress.

To delete a number, press the PHONE button then press and hold

on a call number to display a list of actions including:

Delete entry

Delete list

9.25

09 CONFIGURATION

The SETUP function gives access to the following options: System

language, Date & Time, Display (Brightness, Colour, Map colour), Vehicle,

Units, System.

SETTING THE DATE AND TIME

These settings must be entered again if the battery has been

disconnected.

5

Select the "Date format" function and

1

2

3

4

press the dial to conﬁrm.

Press the SETUP button.

6

Select the "Date & Time" function

and press the dial to conﬁrm.

Conﬁrm the format required using

the dial.

Select the "Time format" function and

press the dial to conﬁrm.

Date & Time

Select the "Set date & time" function

and press the dial to conﬁrm.

Conﬁrm the format required using the dial.

Pressing the SETUP button for more than 2 seconds gives

access to:

Set date & time

Description of the unit

GPS coverage

Adjust the settings one by one using

the direction arrows and conﬁrm by

means of the dial.

Demo mode

9.26

TRIP COMPUTER

10

TRIP COMPUTER

A FEW DEFINITIONS

Press the MODE button several

times in succession until the trip

computer is displayed.

1

Range: displays the distance which can travelled with the

remaining fuel detected in the tank, based on the average fuel

consumption over the last few miles (kilometres).

This displayed value may vary signiﬁcantly following a change in

the vehicle speed or the relief of the route.

When the range falls below 20 miles (30 km), dashes are

displayed. After ﬁlling with at least 5 litres of fuel, the range is

recalculated and is displayed when it exceeds 60 miles (100 km).

If, whilst driving, dashes are displayed continuously in place of the

digits, contact a PEUGEOT dealer.

-

The "vehicle" tab:

The range, the current fuel

consumption and the distance

remaining.

The "1" (trip 1) tab with:

Current fuel consumption: only calculated and displayed above

The average speed, the average

fuel consumption and the

distance travelled calculated

over route "1".

The "2" (trip 2) tab with the same

functions for a second route.

20 mph (30 km/h).

Average fuel consumption: this is the average fuel consumption

since the last trip computer zero reset.

-

Distance travelled: calculated since the last trip computer zero

reset.

Distance remaining to the destination: calculated with reference

to the ﬁnal destination, entered by the user. If guidance is activated,

the navigation system calculates it as a current value.

Average speed: this is the average speed calculated since the last

trip computer zero reset (ignition on).

Each press of the button at the end of the wiper stalk displays the

different trip computer information in succession, according to the

screen.

9.27

11

SCREEN MENU MAP

Vocal

Within 6 miles (10 km)

4

3

MAIN FUNCTION

1

Loudness

Within 30 miles (50 km)

Within 60 miles (100 km)

3

OPTION A

option A1

option A2

OPTION B...

2

Speed dependent volume

Reset sound settings

3

RADIO

2

"Music" Menu

1

"Radio" Menu

1

Select music

Sound settings

Balance / Fader

Bass / Treble

Equalizer

2

Waveband

FM

2

"Traffic" Menu

1

3

Messages on route

All warning messages

Only warnings on route

All messages

2

AM

Manual tune

Sound settings

Balance / Fader

Bass / Treble

Equalizer

Linear

2

Linear

4

Classic

Jazz

3

4

Geo. Filter

Within 2 miles (3 km)

Within 3 miles (5 km)

3

Rock/Pop

Techno

4

9.28

Classic

Start route guidance

Postal code

Rearrange route

Replace stopover

Delete stopover

Recalculate

4

3

Jazz

Rock/Pop

Save to address book

Intersection

Techno

Vocal

City district

Fast route

4

Loudness

3

Geo position

Short route

Speed dependent volume

Reset sound settings

Map

Optimized route

POI search

Navigate HOME

Choose from address book

Choose from last destinations

TMC station information

Stopovers

3

2

POI nearby

3

POI near destination

POI in city

"Navigation" Menu

1

Abort guidance/Resume guidance

Destination input

2

POI in country

POI near route

Route options

Route type

2

Add stopover

3

Enter new address

Country

3

Address input

4

2

4

Navigate HOME

City

3

4

Choose from address book

Choose from last destinations

Fast route

Street

4

House number

Short route

9.29

Optimized route

Route dynamics

Trafﬁc independent

Semi-dynamic

4

"Phone" Menu

"SETUP" menu

1

3

System language*

Deutsch

4

2

Dial from address book

Call lists

3

Avoidance criteria

Avoid motorways

Avoid toll roads

Avoid ferries

English

3

Connect phone

Search phone

Español

4

Français

3

Phones connected

Disconnect phone

Italiano

Recalculate

Nederlands

Polski

3

4

Settings

Rename phone

Delete pairing

Delete all pairings

Show details

2

4

Navi volume

Portuguese

Date & Time*

Set date & time

Date format

Time format

3

POI categories on Map

Set parameters for risk areas

Display on map

2

3

Settings

4

2

Visual alert

Sound alert

Select ring tone

4

3

Phone / Ring tone volume

Enter mailbox number

* Available according to model.

9.30

Display

Units

2

Brightness

Colour

Temperature

3

Celsius

3

4

Pop titanium

Fahrenheit

4

Toffee

Metric / Imperial

3

4

Blue steel

Kilometres (Consumption: l/100)

4

Technogrey

Kilometres (Consumption: km/l)

4

Dark blue

Miles (Consumption: MPG)

4

Map colour

System

2

3

Day mode for map

Night mode for map

Auto. Day/Night for map

Factory reset

Software version

Automatic scrolling

4

3

Vehicle**

2

Vehicle information

3

Alert log

4

Status of functions

4

** The parameter settings vary according to vehicle.

9.31

FREQUENTLY ASKED QUESTIONS

QUESTION

ANSWER

SOLUTION

There is a difference in

sound quality between

the different audio

For optimum sound quality, the audio settings (Volume, Bass, Treble,

Ambience, Loudness) can be adapted to the different sound sources,

which may result in audible differences when changing source (radio,

CD...).

Check that the audio settings (Volume, Bass,

Treble, Ambience, Loudness) are adapted to

the sources listened to. It is advisable to set

the AUDIO functions (Bass, Treble, Front-Rear

Balance, Left-Right Balance) to the middle

position, select the Linear musical ambience and

set the loudness correction to the "Active" position

in CD mode or to the "Inactive" position in radio

mode.

sources (radio, CD...).

The CD is ejected

automatically or is not

played by the player.

The CD is inserted upside down, is unplayable, does not contain any

audio data or contains an audio format which the player cannot play.

The CD is protected by an anti-pirating protection system which is not

recognised by the audio equipment.

-

Check that the CD is inserted in the player the

right way up.

Check the condition of the CD: the CD cannot

be played if it is too damaged.

Check the content in the case of a recorded

CD: consult the advice in the Audio section.

The audio equipment's CD player does not

play DVDs.

Because of their quality level, certain

writeable CDs will not be played by the audio

system.

The CD player sound is

poor.

The CD used is scratched or of poor quality.

Insert good quality CDs and store them in suitable

conditions.

The audio equipment settings (bass, treble, ambiences) are unsuitable.

Set the treble or bass level to 0, without selecting

an ambience.

9.32

QUESTION

ANSWER

An incorrect waveband is selected.

SOLUTION

The stored stations do

not function (no sound,

87.5 Mhz is displayed...).

Press the BAND AST button to return to the

waveband (AM, FM1, FM2, FMAST) on which the

stations are stored.

The quality of reception

of the radio station

listened to gradually

deteriorates or the stored

stations do not function

(no sound, 87.5 Mhz is

displayed...).

The vehicle is too far from the transmitter used by the station listened

to or there is no transmitter in the geographical area through which the

vehicle is travelling.

Activate the RDS function to enable the system

to check whether there is a more powerful

transmitter in the geographical area.

The environment (hills, buildings, tunnels, basement car parks...) block

reception, including in RDS mode.

This phenomenon is normal and does not indicate

a failure of the audio equipment.

The aerial is absent or has been damaged (for example when going

through a car wash or into an underground car park).

Have the aerial checked by a PEUGEOT dealer.

Sound cut-outs of 1 to

During this brief sound cut-out, the RDS searches for any frequency

Deactivate the RDS function if the phenomenon is

too frequent and always on the same route.

2 seconds in radio mode. permitting better reception of the station.

With the engine off,

the audio equipment

switches off after a few

minutes of use.

When the engine is switched off, the audio equipment operating time

Start the vehicle's engine to increase the battery

charge.

depends on the battery charge.

The switch-off is normal: the audio equipment switches to economy mode

and switches off to prevent discharging of the vehicle's battery.

9.33

QUESTION

ANSWER

SOLUTION

TA is selected. However,

certain trafﬁc jams

along the route are not

indicated in real time.

On starting, it is several minutes before the system begins to receive the

trafﬁc information.

Wait until the trafﬁc information is being received

correctly (displaying of the trafﬁc information

symbols on the map).

In certain countries, only major routes (motorways...) are listed for the

trafﬁc information.

This phenomenon is normal. The system is

dependent on the trafﬁc information available.

I receive a speed camera The system announces all speed cameras located in a conical zone

Zoom the map to view the exact position of the

alert for a camera which

is not on my route.

forward of the vehicle. It may detect speed cameras on nearby or parallel speed camera.

roads.

The audible speed

camera alert is not

working.

Audible alerts are not active.

Activate audible alerts in Navigation Menu,

Settings, Set parameters for risk areas.

The alert volume level is set to minimum.

Increase the speed camera alert volume.

The altitude is not

displayed.

On starting, the initialisation of the GPS may take up to 3 minutes to

receive more than 3 satellites correctly.

Wait until the system has started up completely.

Check that there is a GPS coverage of at least

3 satellites (long press on the SETUP button,

then select GPS coverage).

Depending on the geographical environment (tunnel...) or the weather,

the conditions of reception of the GPS signal may vary.

This phenomenon is normal. The system is

dependent on the conditions of reception of the

GPS signal.

The route is not

calculated successfully.

The exclusion criteria may conﬂict with the current location (exclusion of

toll roads on a motorway with tolls).

Check the exclusion criteria.

9.34

QUESTION

ANSWER

SOLUTION

There is a long waiting

When a new medium is inserted, the system reads a certain amount of

This phenomenon is normal.

time after inserting a CD. data (directory, title, artist, etc.). This may take a few seconds.

I cannot connect my

Bluetooth telephone.

The telephone's Bluetooth function may be deactivated or the equipment

may not be visible.

-

Check that your telephone's Bluetooth

function is activated.

Check that your telephone is visible.

A telephone connected

by Bluetooth is inaudible.

The volume level depends on both the system and the telephone.

Increase the Peugeot Connect Navigation volume

setting, possibly to maximum, and increase the

telephone volume level if necessary.

9.35

9.36

Peugeot Connect Sound (RD5)

AUDIO SYSTEM / BLUETOOTH^®

CONTENTS

p. 9.38

p. 9.39

p. 9.40

p. 9.41

p. 9.44

p. 9.47

p. 9.50

p. 9.52

p. 9.53

p. 9.58

01 First steps

02 Steering mounted controls

03 Main menu

04 Audio

05 Music media players

06 Bluetooth

07 Configuration

08 Trip computer

09 Screen menu map

Frequently asked questions

Your Peugeot Connect Sound (RD5) is coded in such

a way that it will only operate in your vehicle.

For safety reasons, the driver must carry out operations

which require prolonged attention while the vehicle is

stationary.

When the engine is switched off and to prevent

discharging of the battery, the audio equipment may

switch off after a few minutes.

9.37

01 FIRST STEPS

Display the list of

local stations.

Long press: CD

tracks or MP3 folders

(CD / USB).

Audio settings: front/

rear fader, left/right

balance, bass/treble,

loudness, audio

Select source:

radio, audio CD / MP3 CD, USB,

Jack connection, Streaming,

AUX.

Select wavebands

FM1, FM2, FMast and

AM.

Abandon the current

operation.

ambiences.

TA (Trafﬁc Announcements)

on/off.

Long press: PTY* (radio

Programme TYpe) mode.

Eject CD.

Select the screen display

mode:

Automatic frequency search

down/up.

Date, audio functions, trip

computer, telephone.

Select previous/next CD, MP3

or USB track.

Conﬁrm.

On/off, volume setting.

The DARK button changes the screen display

for improved driving comfort at night.

Buttons 1 to 6:

Select a pre-set radio station.

Long press: pre-set a station.

Display main menu.

Select next frequency down/up.

Select previous/next MP3 folder.

Select previous/next folder / genre /

artist / playlist (USB).

1^stpress: upper bar only illuminated.

2^ndpress: black screen.

3^rdpress: return to standard display.

*

Available according to version.

9.38

02 STEERING MOUNTED CONTROLS

Radio: automatic search for a higher

frequency.

Radio: select the previous/next pre-set

station.

CD / MP3 / USB: selection of the next

track.

USB: select genre / artist / folder from the

classiﬁcation list.

CD / USB: continuous press: fast

forwards play.

Select the previous/next item in a menu.

Move in the list.

Volume increase.

Mute: press the volume

increase and decrease

buttons simultaneously.

The sound is restored

by pressing one of the

two volume buttons.

Change audio source.

Conﬁrm a selection.

Call/end call on the telephone.

Press for more than 2 seconds:

telephone main menu.

Volume decrease.

Radio: automatic search for a lower

frequency.

CD / MP3 / USB: selection of the

previous track.

CD / USB: continuous press: fast

reverse.

Move in the list.

9.39

03 MAIN MENU

TELEPHONE:

Bluetooth hands-free,

pairing, management

of a call.

AUDIO FUNCTIONS:

radio, CD, USB, options.

> MONOCHROME SCREEN C

TRIP COMPUTER:

entering of distances,

alerts, status of functions.

PERSONALISATION-

CONFIGURATION:

vehicle parameters,

display, languages.

> MONOCHROME SCREEN A

For a detailed global view of the

menus available, refer to the

"Screen menu map" section.

9.40

The external environment (hills, buildings, tunnels, basement car parks, ...)

may block reception, including in RDS mode. This is a normal effect of the

way in which radio waves are transmitted and does not indicate any failure

of the audio system.

04 AUDIO

RADIO

RDS

SELECTING A STATION

1

2

3

Press the SOURCE button several

Press the MENU button.

SOURCE

times in succession and select the

radio.

MENU

2

Select AUDIO FUNCTIONS then

press OK.

Press the BAND AST button to select

a waveband: FM1, FM2, FMast, AM.

BAND

AST

3

Select the FM WAVEBAND

PREFERENCES function then press OK.

Brieﬂy press one of the buttons to

carry out an automatic search of the

radio stations.

4

Select ACTIVATE RDS then press

OK. RDS appears on the screen.

4

Press one of the buttons to carry out

a manual search up / down for radio

frequencies.

In radio mode, press OK directly to activate / deactivate RDS

mode.

Press the LIST REFRESH button to

display the list of stations received

locally (30 stations maximum).

To update this list, press for more

than two seconds.

The RDS, if displayed, enables you to continue listening to the same

station by automatic retuning to alternative frequencies. However, in certain

conditions, coverage of an RDS station may not be assured throughout the

country as radio stations do not cover 100 % of the territory. Under conditions

of very weak reception, the system may change to a regional station.

LIST

REFRESH

9.41

04 AUDIO

CD

RECEIVING TA MESSAGES

PLAYING A CD

The TA (Trafﬁc Announcement) function gives priority to TA alert

messages. To operate, this function needs good reception of a

radio station transmitting this type of message. When a trafﬁc

report is transmitted, the current audio source (Radio, CD, ...) is

interrupted automatically to play the TA message. Normal playback

of the audio source resumes at the end of the transmission of the

message.

Insert circular compact discs only.

Some anti-pirating systems, on original discs or CDs copied using a

personal recorder, may cause faults which are no reﬂection on the

quality of the original player.

Without pressing the EJECT button, insert a CD in the player, play

begins automatically.

1

2

To play a disc which has already been

inserted, press the SOURCE button

Press the TA button to activate or

deactivate trafﬁc messages.

SOURCE

several times in succession and

select CD.

Press one of the buttons to select a

track on the CD.

Press the LIST REFRESH button to display the list of tracks on the CD.

3

Press and hold one of the buttons for

fast forward or backward.

9.42

04 AUDIO

MP3 CD

INFORMATION AND ADVICE

PLAYING AN MP3 COMPILATION

Insert an MP3 compilation in the player.

The MP3 format, an abbreviation of MPEG 1.2 & 2.5 Audio Layer 3,

is an audio compression standard which permits the recording of

several tens of music ﬁles on a single disc.

The audio equipment searches for all of the music tracks, which

may take anything between a few seconds and several tens of

seconds, before play begins.

On a single disc, the CD player can read up to 255 MP3 ﬁles spread

over 8 folder levels. However, it is advisable to keep to a limit of two

levels to reduce the access time before the CD is played.

While the CD is being played, the folder structure is not followed.

All of the ﬁles are displayed on a single level.

In order to be able to play a recorded CDR or CDRW, when

recording, the ISO 9660 level 1.2 or Joliet ﬁle format is

recommended.

If the disc is recorded in another format, it may not be played

correctly.

It is recommended that the same recording format is always

used for an individual disc, with as low a speed as possible

(4x maximum) for optimum sound quality.

In the particular case of a multi-session CD, the Joliet format is

recommended.

To play a disc which has already

1

2

been inserted, press the SOURCE

SOURCE

button several times in succession

and select CD.

The audio system will only play ﬁles with the extension ".mp3" with

a sampling rate of 22.05 KHz or 44.1 KHz. No other type of ﬁle

(.wma, .mp4, .m3u...) can be played.

Press one of the buttons to select a

track on the CD.

Press the LIST REFRESH button to display the list of directories of

the MP3 compilation.

It is advisable to restrict ﬁle names to 20 characters without using

special characters (e.g. " ? ; ù) to avoid any playing or displaying

problems.

3

Press and hold one of the buttons for

fast forward or backward play.

Empty CDs are not recognised and may damage the system.

9.43

05 MUSIC MEDIA PLAYERS

The list of compatible equipment and the compression rates supported

are available from PEUGEOT dealers.

USING THE PEUGEOT CONNECT USB

CONNECTING A USB MEMORY STICK

1

This unit consists of a USB port and an auxiliary

Connect the memory stick to the port, directly or

using a lead. If the audio equipment is switched

on, the USB source is detected as soon as it

is connected. Play begins automatically after a

delay which depends on the capacity of the USB

memory stick.

Jack socket*. The audio ﬁles are transmitted

1

from a portable device - digital player or a USB

memory stick - to your Peugeot Connect Sound

(RD5) and heard via the vehicle's speakers.

The ﬁle formats supported are .mp3 (mpeg1

layer 3 only), .wma (standard 9 only,

USB memory stick (1.1, 1.2 and 2.0) or Apple^®

player of generation 5 or later:

128 kbits/sec compression), .wav and .ogg.

2

Certain playlist formats are supported (.m3u, ...)

On reconnection of the previous memory stick

used, play is resumed automatically with the last

track played.

-

USB memory sticks should be

formatted FAT or FAT 32 (NTFS not

supported),

-

the Apple^®player lead is essential,

navigation through the ﬁle database is also

possible by means of the steering mounted

controls.

The system puts together playlists (temporary memory) created

over a period which depends on the capacity of the USB device.

The other sources are available during this time.

The playlists are updated each time the ignition is switched off or

each time a USB memory stick is connected.

When connecting for the ﬁrst time, the classiﬁcation suggested

is by folder. When you reconnect, the classiﬁcation selected

previously is retained.

3

Other Apple^®players of earlier generations and

players using the MTP protocol*:

-

play via Jack-Jack lead only (not supplied),

navigation through the ﬁle database is from

the portable device.

* According to vehicle.

9.44

05 MUSIC MEDIA PLAYERS

USING THE PEUGEOT CONNECT USB

Press one of these buttons to gain

access to the previous / next track on

the classiﬁcation list currently being

played.

Press and hold one of the buttons for

fast forward or backward play.

2

3

Press and hold LIST to display the

different classiﬁcations.

Select by Folder / Artist / Genre / Playlist,

press OK to select the classiﬁcation

required, then press OK again to conﬁrm.

4

Press one of these buttons to

gain access to the previous / next

Genre, Folder, Artist or Playlist on

the classiﬁcation list currently being

played.

-

by Folder: all folders containing audio

ﬁles recognised on the peripheral

device.

by Artist: all of the artist names

deﬁned in the ID3 Tags, classiﬁed in

alphabetical order.

LIST

REFRESH

-

by Genre: all of the genres deﬁned in

CONNECTING AN APPLE^®PLAYER VIA THE USB PORT

the ID3 Tags.

by Playlist: in accordance with the

playlists recorded on the USB device.

1

The lists available are Artist, Genre and Playlist (as deﬁned in the

Apple^®player).

Selection and Navigation are described in steps 1 to 4 above.

Press LIST brieﬂy to display the

previously selected classiﬁcation.

LIST

REFRESH

Navigate through the list using the left/

right and up/down buttons.

Conﬁrm the selection by pressing OK.

Do not connect a hard disk or USB connection device other

than audio equipment to the USB port. This could damage your

installation.

9.45

05

MUSIC MEDIA PLAYERS

USING THE AUXILIARY SOCKET (AUX)

ADJUSTING THE VOLUME OF

THE AUXILIARY SOURCE

RCA SOCKET

1

The RCA auxiliary socket permits the connection of a portable device

(MP3 player...).

First adjust the volume of your portable device.

1

2

Connect the portable device (MP3

player…) to the audio sockets (white and

red, RCA type) using a suitable cable

(not supplied).

Then adjust the volume of your audio

system.

2

Press the SOURCE button several

times in succession and select AUX.

SOURCE

The display and control is via the portable device.

9.46

06 BLUETOOTH

The services offered depend on the network, the SIM card and the

compatibility of the Bluetooth equipment used.

Consult your telephone's manual and your operator to ﬁnd out which

services are available to you.

BLUETOOTH TELEPHONE

SCREEN C

(Available according to model and version)

5

PAIRING A TELEPHONE / FIRST CONNECTION

The ﬁrst 4 telephones recognised are displayed in this window.

For safety reasons and because they require prolonged attention

on the part of the driver, the operations for pairing of the Bluetooth

mobile telephone with the Bluetooth hands-free system of your

audio equipment must be carried out with the vehicle stationary

and the ignition on.

The TELEPHONE menu permits access to the following functions

in particular: Directory*, Call list, Pairing management.

* If your telephone is fully compatible.

Select the telephone to be connected from the list. Only one

telephone can be connected at a time.

6

7

Go to www.peugeot.co.uk for more information (compatibility, more

help, ...).

Activate the telephone's Bluetooth function

and ensure that it is "visible to all" (telephone

conﬁguration).

1

2

A virtual keypad is displayed in the

screen: enter a code with at least 4 digits.

Conﬁrm by pressing OK.

A message is displayed in the screen of the

8

9

Press the MENU button.

telephone chosen. To accept the pairing, enter the

same code on the telephone, then conﬁrm with OK.

MENU

If pairing fails, the number of attempts is not limited.

In the menu, select:

3

4

-

Bluetooth telephone function -

Audio

A message that the pairing has been successful appears in the

screen.

OK

-

Bluetooth conﬁguration

Perform a Bluetooth search

The automatic connection authorised is only active after the

telephone has been conﬁgured.

The directory and the call list can be accessed after the

synchronisation period.

A window is displayed with a message that a search is in progress.

9.47

06

BLUETOOTH

RECEIVING A CALL

MAKING A CALL

An incoming call is announced by a ring and a superimposed

display in the vehicle's screen.

1

2

From the Bluetooth telephone function Audio menu, select Manage

the telephone call then Call, Call list or Directory.

2

Press the steering mounted control for more than

two seconds for access to your directory, then

navigate with the thumb wheel.

Select the YES tab on the display

using the buttons and conﬁrm by

pressing OK.

OK

Or

To dial a number, use your telephone's keypad,

with the vehicle stationary.

Press the steering mounted control to accept the

call.

ENDING A CALL

1

During a call, press the steering mounted control

for more than 2 seconds.

Conﬁrm with OK to end the call.

9.48

06

BLUETOOTH

BLUETOOTH AUDIO STREAMING*

3

Wireless transmission of the telephone's music ﬁles via the audio

equipment. The telephone must be able to manage the appropriate

Bluetooth proﬁles (Proﬁles A2DP / AVRCP).

Activate the streaming source by

pressing the SOURCE button**.

The tracks to be played can be

controlled as usual via the buttons on

the audio system control panel and

the steering mounted controls***.

The contextual information can be

displayed on the screen.

SOURCE

1

Initiate the pairing between the telephone and

the vehicle. This pairing can be initiated from

the vehicle's telephone function menu or via the

telephone's keypad. See steps 1 to 9 on the previous

pages. During the pairing phase, the vehicle must be

stationary with the key in the ignition.

* Depending on the compatibility of the telephone.

** In certain cases, playing of the Audio ﬁles must be initiated from the

keypad.

*** If the telephone supports the function.

Select the telephone to be connected from the telephone function

menu.

2

The audio system connects to a newly paired telephone

automatically.

9.49

07

CONFIGURATION

SETTING THE DATE AND TIME

SCREEN A

1

2

3

5

6

7

8

Press the MENU button.

Press to conﬁrm the selection.

MENU

OK

Using the arrows, select DISPLAY

CONFIGURATION.

Adjust the setting.

Press to conﬁrm the selection.

OK

4

Start again from step 1 then set

MONTH, DAY, HOUR, MINUTES.

Using the arrows, select YEAR.

OK

9.50

07

CONFIGURATION

SETTING THE DATE AND TIME

SCREEN C

1

2

3

4

5

6

7

8

Press the MENU button.

Press to conﬁrm the selection.

MENU

OK

Using the arrows, select

PERSONALISATION

CONFIGURATION.

Using the arrows, select ADJUST

DATE AND TIME.

Press to conﬁrm the selection.

OK

Adjust the settings one by one

conﬁrming by pressing the OK

button. Next select the OK tab on the

screen then conﬁrm.

Using the arrows, select DISPLAY

CONFIGURATION.

OK

9.51

08

TRIP COMPUTER

A FEW DEFINITIONS

Range: displays the distance which can travelled with the remaining fuel

detected in the tank, based on the average fuel consumption over the last

few miles (kilometres).

This displayed value may vary signiﬁcantly following a change in the

vehicle speed or the relief of the route.

Each press of the button, located at the end of the

wiper stalk, displays the different trip computer

information in succession, depending on the screen.

When the range falls below 20 miles (30 km), dashes are displayed.

After ﬁlling with at least 5 litres of fuel, the range is recalculated and is

displayed when it exceeds 60 miles (100 km).

If, whilst driving, dashes are displayed continuously in place of the digits,

contact a PEUGEOT dealer.

Current fuel consumption: only calculated and displayed above 20 mph (30 km/h).

Average fuel consumption: this is the average fuel consumption since

the last trip computer zero reset.

1

Distance travelled: calculated since the last trip computer zero reset.

-

the "vehicle" tab with:

● the range, the current fuel consumption and the distance remaining

to the destination,

the "1" tab (trip 1) with:

● the average speed, the average consumption and the distance

travelled calculated over trip "1"

Distance remaining to the destination: calculated with reference to

the ﬁnal destination, entered by the user. If guidance is activated, the

navigation system calculates it as a current value.

Average speed: this is the average speed calculated since the last trip

computer zero reset (ignition on).

the "2" tab (trip 2) with the same information for a second trip.

Zero reset

When the required trip is displayed, press the control for more than

two seconds.

9.52

09 SCREEN MENU MAP

RADIO-CD

OPTIONS

MONOCHROME A

1

RDS SEARCH

DIAGNOSTICS

CONSULT

2

REG MODE

2

3

MAIN FUNCTION

1

CD REPEAT

ABANDON

2

OPTION A

RANDOM PLAY

2

OPTION A1

OPTION A2

OPTION B...

3

VEHICLE CONFIG*

1

2

REV WIPE ACT

GUIDE LAMPS

2

* The parameters vary according to vehicle.

9.53

09

SCREEN MENU MAP

DISPLAY ADJUST

LANGUAGE

UNITS

1

YEAR

FRANCAIS

TEMPERATURE: °CELSIUS / °FAHRENHEIT

2

FUEL CONSUMPTION:

KM/L - L/100 - MPG

MONTH

ITALIANO

DATE

NEDERLANDS

PORTUGUES

PORTUGUES-BRASIL

DEUTSCH

HOUR

MINUTES

12 H/24 H MODE

ENGLISH

ESPANOL

9.54

09

SCREEN MENU MAP

MONOCHROME C

Press the OK dial for access to short-cut menus according to the display

on the screen:

CD / MP3 CD

USB

RADIO

activate / deactivate Intro

activate / deactivate track repeat (of the

current folder / artist / genre / playlist)

activate / deactivate RDS

1

activate / deactivate track repeat

(the entire current CD for CD, the entire

current folder for MP3 CD)

activate / deactivate REG mode

1

activate / deactivate radiotext

1

activate / deactivate random play (of the

current folder / artist / genre / playlist)

activate / deactivate random play

(the entire current CD for CD, the entire

current folder for MP3 CD)

1

9.55

09

SCREEN MENU MAP

MONOCHROME C

TRIP COMPUTER

AUDIO FUNCTIONS

1

Pressing the MENU button displays:

ENTER DISTANCE TO DESTINATION

Distance: x miles

FM BAND PREFERENCES

2

alternative frequencies (RDS)

3

ALERT LOG

activate / deactivate

4

Diagnostics

regional mode (REG)

STATUS OF THE FUNCTIONS*

Functions activated or deactivated

activate / deactivate

4

radio-text information (RDTXT)

activate / deactivate

4

PLAY MODES

2

album repeat (RPT)

3

activate / deactivate

track random play (RDM)

activate / deactivate

4

3

* The parameters vary according to vehicle.

9.56

09

SCREEN MENU MAP

PERSONALISATION-CONFIGURATION

BLUETOOTH TELEPHONE

1

DEFINE THE VEHICLE PARAMETERS*

DISPLAY CONFIGURATION

video brightness adjustment

normal video

BLUETOOTH CONFIGURATION

Connect/Disconnect a device

Telephone function

2

3

Audio Streaming function

Consult the paired device

4

inverse video

4

brightness (- +) adjustment

date and time adjustment

day/month/year adjustment

hour/minute adjustment

choice of 12 h / 24 h mode

choice of units

4

Delete a paired device

4

3

Perform a Bluetooth search

4

CALL

2

Calls list

3

Download User Manual App

TECHNOLOGY on BOARD for Your Peugeot Partner Van 2008-2014

Related Topics

TECHNICAL DATA

Popular Owner Manuals

Latest Owner Manuals