2002-2010 Porsche Cayenne SUV Multi-Purpose Display and Instruments User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Multi-Purpose Display and Instruments for Your Porsche Cayenne SUV First Generation (2002-2010)

Multi-Purpose Display and Instruments 117
Multi-Purpose Display and Instruments
Instrument panel .........................................118
Oil temperature gauge.................................120
Tachometer................................................120
Clock .........................................................120
Cooling system...........................................121
Fuel gauge .................................................122
Intelligent Maintenance Computer
for the Cayenne (V6)....................................122
Odometer...................................................123
Speedometer..............................................123
Voltmeter ...................................................124
Emission control .........................................125
Operating the multi-purpose display
on the instrument panel ...............................126
Displaying/resetting average speed .............129
Displaying range on remaining fuel ...............129
Displaying tyre pressure ..............................129
Displaying compass ................................... 129
Displaying navigation information..................129
Opening the main menu ...............................129
Operating the telephone via the
multi-purpose display...................................130
Setting speed limit on the
multi-purpose display...................................132
Displaying warning messages ......................133
Displaying status of level control ..................134
Displaying status of locks/reduction .............134
Displaying average consumption ..................135
Setting Tyre Pressure Monitoring .................135
Switching off passenger compartment
monitoring and inclination sensor
on the multi-purpose display ........................144
Synchronous adjustment of door mirrors ..... 145
Changing settings for opening and locking
the vehicle ................................................. 145
Setting lighting off delay ............................. 147
Setting the clock ........................................ 148
Setting compass........................................ 149
Changing language for displays ................... 150
Changing units for displays ......................... 150
Resetting display to factory settings ............ 150
Overview of warning messages ................... 151
Mobile phones and 2-way radios.................. 160
Porsche Communication Management
(PCM) ........................................................ 160
Radio ........................................................ 161
Fire extinguisher......................................... 161
118 Multi-Purpose Display and Instruments
Instrument panel
Warning and indicator lights on the
tachometer
Indicator lights in central instrument
panel
Warning and indicator lights on the
speedometer
A Oil temperature gauge
B Tachometer
C Clock
D Clock setting button
E Cooling system temperature gauge
F Multi-purpose display
G Fuel gauge
H Reset button for trip counter display
I Speedometer
J Mileage displays
K Voltmeter
Emission control warning light
(Check Engine)
Airbag warning light
Seat belt warning light
PSM warning light
ABS warning light
Cruise control readiness
Direction indicator, left
Indicator light
Direction indicator, right
Indicator light
Trailer direction indicator
Indicator light
Rear fog light indicator light
Tyre pressure warning light
Differential lock indicator light
Brake warning light
Fog light indicator light
General warning
Observe warning message on the multi-
purpose display
High beam indicator light
Multi-Purpose Display and Instruments 119
120 Multi-Purpose Display and Instruments
A warning message will appear on the multi-
purpose display of the instrument panel if the
engine oil temperature is too high.
f Reduce engine speed and engine load
immediately if the red zone is reached.
f For information on warning messages on the
multi-purpose display:
Please observe the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 151.
Tachometer
The start of the red zone on the tachometer scale
is a visual warning of the maximum permissible
engine speed.
If the red zone is reached during acceleration, fuel
feed is interrupted in order to protect the engine.
Clock
The clock A is adjusted on the multi-purpose
display of the instrument panel:
f Press button B.
The menu SETTINGS > CLOCK is automatically
opened on the multi-purpose display.
f For information on setting the clock:
Please observe the chapter “SETTING THE
CLOCK” on Page 148.
Oil temperature gauge
Multi-Purpose Display and Instruments 121
f If the cooling system is in any way faulty,
consult a qualified specialist workshop. We
recommend that you use a Porsche partner for
this work since these are staffed with trained
personnel and have the necessary parts and
tools.
Temperature gauge
Pointer to the left – engine cold
f Avoid high engine speeds and heavy engine
loading.
Pointer in the middle – normal operating
temperature
Pointer may move up to the red area when engine
is heavily loaded and outside temperature is high.
Coolant temperature warning
A warning message will appear on the multi-
purpose display of the instrument panel if the
engine coolant temperature is too high.
f Switch engine off and let it cool.
f Check radiators and air passages in front end
of vehicle for obstructions.
f Check coolant level.
Add coolant if necessary.
f Have the fault remedied.
f For further information on coolant, checking
the coolant level and topping up coolant:
Please observe the chapter “CHECKING THE
COOLANT LEVEL AND ADDING COOLANT” on
Page 271.
Note on operation
To prevent excessive temperatures, the cooling
air ducts must not be obstructed by covering with
films or “stone guards” etc.
Coolant level warning
A warning message will appear on the multi-
purpose display of the instrument panel if the
engine coolant level is too low.
f Switch engine off and let it cool.
f Add coolant.
Have the cause for the fault remedied. Consult
a qualified specialist workshop. We recom-
mend that you use a Porsche partner for this
work since these are staffed with trained
personnel and have the necessary parts and
tools.
f For further information on coolant, checking
the coolant level and topping up coolant:
Please observe the chapter “CHECKING THE
COOLANT LEVEL AND ADDING COOLANT” on
Page 271.
f For information on warning messages on the
multi-purpose display:
Please observe the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 151.
Caution!
Risk of engine damage.
f Do not continue driving if the warning persists
even when the engine coolant level is correct.
f Have the fault remedied.
Cooling system
122 Multi-Purpose Display and Instruments
When the ignition is on, the fuel level is displayed.
f For information on fuel quality and filling
quantities:
Please observe the chapter “CAPACITIES” on
Page 372.
f For information on fuel and refuelling:
Please observe the chapter “FILLING WITH
FUEL” on Page 280.
If the vehicle’s inclination changes (e.g. going
uphill/downhill), minor deviations in the indication
may occur.
Fuel reserve warning
When the ignition is switched on or the engine is
running, the warning light on the multi-purpose
display of the instrument panel lights up if less
than approx. 12 litres of fuel remains in the tank or
the range on remaining fuel falls below approx.
50 km (30 miles).
f Fill up at the next opportunity.
Caution!
A shortage of fuel may cause damage to the
emission control system.
f Never drive the tank dry.
f If the warning lights have come on, do not take
bends at high speed.
f For further information on the emission control
system: Please observe the chapter
“EMISSION CONTROL SYSTEM” on Page 279.
Intelligent Maintenance Computer
for the Cayenne (V6)
The maintenance intervals (service indicator)
shown on the multi-purpose display depend on the
mileage, the time since the last service and the
operating conditions of the vehicle.
If the vehicle is operated under heavy load, the
interval between two services is shorter than
under normal operating conditions.
f For information on messages on the multi-
purpose display:
Please observe the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 151.
Fuel gauge
Multi-Purpose Display and Instruments 123
Odometer
The upper display counts the total mileage, the
lower display individual trips.
After exceeding 9,999 kilometres or 6,213 miles,
the trip counter returns to 0.
Resetting trip counter to “0”
f Press button A for approx. 1 second.
Speedometer
The digital speedometer is integrated in the multi-
purpose display in the instrument panel.
An analogue display is also located on the right
next to the multi-purpose display in the instrument
panel.
124 Multi-Purpose Display and Instruments
The voltmeter indicates the vehicle electrical
system voltage.
Normal range: 12 to 16 V.
The voltage may drop considerably when the
vehicle is being started.
If the indicator is constantly below 12 V when
the engine is running:
f Have the battery charging system checked.
f Consult a qualified specialist workshop. We
recommend that you use a Porsche partner for
this work since these are staffed with trained
personnel and have the necessary parts and
tools.
Battery/generator
A warning message will appear on the multi-
purpose display of the instrument panel if the
vehicle electrical system voltage drops signifi-
cantly.
f Stop at a safe place and switch the engine off.
f For information on warning messages on the
multi-purpose display:
Please observe the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 151.
Possible causes
– Defect in the battery charging system
– Torn drive belt
Warning!
Risk of accident and risk of engine damage.
A torn drive belt means there is no power
assistance to the steering (more effort is
required to steer) and engine cooling fails.
f Do not continue driving.
f Have the fault remedied.
f Consult a qualified specialist workshop. We
recommend that you use a Porsche partner for
this work since these are staffed with trained
personnel and have the necessary parts and
tools.
Danger of steering assistance failing during
a long journey in water if the drive belt slips.
f If the steering assistance fails, more effort will
be required to steer.
Voltmeter
Multi-Purpose Display and Instruments 125
Emission control
The emission control system detects malfunctions
early that could, for example, cause increased
pollutant emissions or consequential damage.
Faults are indicated by the warning light on the
instrument panel which then either lights up contin-
uously or flashes.
The faults are recorded in the control unit’s fault
memory.
The warning light on the instrument panel lights up
when the ignition is switched on as a lamp check
and goes out approx. 4 seconds after the engine
starts.
The warning light on the instrument panel flashes
to indicate operating states (e.g. engine misfiring)
which might cause damage to certain parts of the
emission control system.
f In this case, immediately reduce the engine
load by easing off the accelerator.
The warning light in the instrument panel is lit
continuously after the critical range is left.
In order to avoid consequential damage to the
engine or the exhaust-gas cleaning system (e.g.
catalytic converter):
f Consult a qualified specialist workshop. We
recommend that you use a Porsche partner for
this work since these are staffed with trained
personnel and have the necessary parts and
tools.
Caution!
Risk of damage. If the warning light on the
instrument panel continues flashing even
when you have eased off the accelerator
pedal, the emission control system may
overheat.
f Stop as soon as possible in a safe place.
Make sure that combustible materials, such as
dry grass or leaves, cannot come into contact
with the hot exhaust system.
f Switch off the engine.
f Have the fault remedied.
Warning light
126 Multi-Purpose Display and Instruments
Operating the multi-purpose
display on the instrument panel
On-board computer information can be displayed
on the multi-purpose display. Additional functions
are also available in the main menu which allow
you to change the settings for your vehicle.
Warning!
There is a danger of accident if you set or
operate the multi-purpose display, radio,
navigation system, telephone or other equip-
ment while driving. Operating these devices
while driving could distract you from traffic
and cause you to lose control of the vehicle.
f Operate these components while driving only if
the traffic situation allows you to do so safely.
f Carry out any complicated operating or setting
procedures only with the vehicle stationary.
It is not possible to describe all details of the func-
tions in this Driver's Manual.
The examples clearly demonstrate the functional
principle and clarify the menu structure.
Note on operation
Depending on the equipment of your vehicle,
some information or functions may not be availa-
ble on the multi-purpose display (e.g. telephone,
navigation, audio system, compass or tyre pres-
sure).
Various menus can only be called up when the ve-
hicle is stationary.
Note
The multi-purpose display is ready for operation
only when the ignition is on.
Note on operation
By selecting the menu items
MAIN MENU > SETTINGS > FACTORY SET, you
can reset all individual settings to the basic works
settings.
Note on operation
Arrows at the top and bottom of the menu indicate
additional entries.
f Press rocker switch A up or down.
In the COMFORT menu, the menu scrolls automat-
ically as you approach the end of the list.
Operating principle
The multi-purpose display is operated by means of
the rocker switch A and the ENTER button B on
the windscreen wiper stalk.
Selection or setting
Using the rocker switch A, you can move the bar
up and down to select menu items, change
between display screens and make settings.
Confirmation
Press the ENTER button B to confirm the selected
entry. The selected item is then activated.
Multi-Purpose Display and Instruments 127
Operating example: Displaying average
consumption
Select items with rocker switch on the wiper stalk
in each case and confirm by pressing the ENTER
button.
Note on operation
The measurements for range on remaining fuel
and average consumption are not reset when the
ignition is switched off. The values can therefore
be measured over long periods.
Disconnecting the vehicle battery clears the mem-
ories.
Further on-board computer functions can be dis-
played in the PCM.
f Please follow the separate operating instruc-
tions for PCM.
1. MAIN MENU
> VEHICLE INFO
Select and confirm
2. Select Ø CONSUM.
3. Confirm selection.
The average consumption is now
displayed.
Returning to starting menu
4. Select BACK.
5. Confirm selection.
VEHICLE INFO menu appears.
6. Select BACK.
7. Confirm selection.
MAIN MENU menu appears.
8. Select BACK.
9. Confirm selection.
Basic display appears.
128 Multi-Purpose Display and Instruments
Menu overview of the multi-purpose display
Basic display Main menu Sub-menus Displays and
settings in
the sub-menus
Multi-Purpose Display and Instruments 129
Displaying/resetting average
speed
Displaying range on remaining fuel
The range on remaining fuel is continuously
recomputed while driving based on fuel level,
current consumption and average consumption.
Displaying tyre pressure
This display is available only in conjunction with the
Tyre Pressure Monitoring option.
The current tyre pressures at the actually present
levels are displayed in the “Tyre pressure” screen
of the on-board computer. These values would be
identical to those of a pressure gauge connected
to the four valves. These pressures change while
the vehicle is being driven.
– The tyre pressures increase as the tempera-
ture in the tyres rises, e.g. during high-speed
motorway driving.
– The tyre pressures decrease as the tempera-
tures drop, e.g. during journeys in cold regions
(such as mountains).
The values displayed therefore do not allow
conclusions to be drawn about possible pressure
deviations.
f In order to display pressure deviations from
the prescribed pressure, select the menu item
TYRE PRESS. in the MAIN MENU.
Displaying compass
This display is available only in conjunction with the
Compass or PCM option.
Displaying navigation information
Navigation information can also be displayed on
the multi-purpose display.
This display is available only in conjunction with the
Navigation (PCM) option.
Opening the main menu
The main menu contains the following functions:
f PHONE
MPH-LIMIT
VEHICLE INFO
TYRE PRESS.
SETTINGS
Displaying average speed
1. Switch ignition on.
2. Select Ø MPH.
The average speed is displayed.
The displayed values are based on
the distance travelled since the last
reset to “zero”.
Resetting average speed
3. Select Ø MPH.
The average speed is displayed.
4. Press the ENTER button for longer
than 1 second.
The value is cleared.
1. Switch ignition on.
2. Select remaining range.
The range on remaining fuel is
displayed.
1. Switch ignition on.
2. Select TYRE PRESS.
The tyre pressures are displayed.
1. Switch ignition on.
2. Select COMPASS.
The compass is displayed.
1. Switch ignition on.
2. Select NAVIGATION.
The navigation arrows are
displayed.
1. Switch ignition on.
2. Select MAIN MENU.
3. Confirm selection.
The main menu is displayed.
130 Multi-Purpose Display and Instruments
Operating the telephone via the
multi-purpose display
Note
The telephone function of the multi-purpose
display is linked to both the PCM and the multi-
functional buttons on the steering wheel as well as
the control stalk.
A SIM card must be inserted in the drawer of
the PCM as a prerequisite for telephone
operation.
If the link to the network is lost, no PIN is entered,
no SIM card is inserted or the telephone is
switched off, a corresponding indication will
appear.
Note
The phone number of an incoming call is shown on
the multi-purpose display. The name of the caller
is shown only if the caller is stored in the telephone
book.
Accepting, refusing, ending a call
Incoming calls are shown on the multi-purpose
display (PHONE INFO must be activated).
Displaying telephone calls on the
multi-purpose display
Automatic indication of an incoming call on the
multi-purpose display can be switched on or off
with the PHONE INFO menu.
– ON – Incoming calls are automatically
indicated on the multi-purpose display.
– OFF – Incoming calls are not indicated on the
multi-purpose display.
1. Press the ENTER button.
The display reverts to the last menu.
1.Display on display screen
1. Select ACCEPT or
REFUSE.
2. Confirm selection.
After the call is accepted, END
appears in the menu.
Ending a call
3. Select END.
4. Confirm selection.
The call is ended.
5.
1. MAIN MENU
> PHONE
> PHONE INFO
Select and confirm.
2. Select ON or OFF.
3. Confirm selection.
The selected item is then accepted.
Multi-Purpose Display and Instruments 131
Displaying last numbers and last-number
redial
The LAST NUMBERS menu shows the most recent
entries dialled via the respective SIM card.
Displaying important numbers and calling
The IMPORTANT NOS. menu shows the entries
stored as important numbers on the SIM card.
Note on operation:
If the rocker switch is pressed for longer than one
second, the initial letters for which entries exist
are shown.
This allows the desired entry to be found more
quickly.
Displaying telephone book, selecting
party and calling
The PHONE BOOK menu shows the entries of the
telephone book that are stored on the SIM card.
Note on operation:
If the rocker switch is pressed for longer than one
second, the initial letters for which entries exist
are shown.
This allows the desired entry to be found more
quickly.
4.
1. MAIN MENU
> PHONE
> LAST NUMBERS
Select and confirm.
2. Select entry from the list.
3. Confirm selection.
The connection with the selected
party is established.
4.
1. MAIN MENU
> PHONE
> IMPORTANT NOS.
Select and confirm.
2. Select entry from the list.
3. Confirm selection.
The connection with the selected
party is established.
4.
1. MAIN MENU
> PHONE
> PHONE BOOK
Select and confirm.
2. Select entry from the list.
3. Confirm selection.
The connection with the selected
party is established.
132 Multi-Purpose Display and Instruments
Displaying missed calls, calling back
party
The telephone numbers of the rejected calls are
shown in the MISSED CALLS menu. The numbers
are stored on the SIM card.
Note on operation:
If the rocker switch is pressed for longer than one
second, the initial letters for which entries exist
are shown.
This allows the desired entry to be found more
quickly.
Setting speed limit on the multi-
purpose display
A speed limit can be entered to monitor the driving
speed. When it is exceeded, a signal sounds and
the multi-purpose display displays the message
LIMIT EXCEEDED.
Accepting current speed
You can define the current speed as the speed
limit in the menu MPH-LIMIT.
Presetting speed
You can define a speed limit in the menu MPH-
LIMIT.
4.
1. MAIN MENU
> PHONE
> MISSED CALLS
Select and confirm.
2. Select entry from the list.
3. Confirm selection.
The connection with the selected
party is established.
4.
1. MAIN MENU
> MPH-LIMIT
Select and confirm
2. Select CURRENT MPH.
3. Confirm selection.
LIMIT ACTIVE is activated automati-
cally and the selected speed limit is
shown.
4.
1. MAIN MENU
> MPH-LIMIT
Select and confirm
2. Select MPH SET.
3. Set desired limit:
– Press briefly: Limit is set in
increments of 1mph.
– Press for longer than 2 seconds:
Limit is set in increments of 10 mph.
4. Confirm selection.
LIMIT ACTIVE is activated automati-
cally.
Multi-Purpose Display and Instruments 133
Activating or deactivating the limit
Example: Check side lights warning message
Displaying warning messages
All current warnings and information relating to the
traffic safety of the vehicle can be displayed in the
menu WARNINGS.
Caution!
Warning messages indicate possible faults.
f Consult a qualified specialist workshop. We
recommend that you use a Porsche partner for
this work since these are staffed with trained
personnel and have the necessary parts and
tools.
5.
1. MAIN MENU
> MPH-LIMIT
Select and confirm.
2. Select LIMIT ACTIVE.
3. Confirm selection.
LIMIT ACTIVE is activated
LIMIT ACTIVE is deactivated
4. Select BACK.
5. Confirm selection.
Sub-menu MPH-LIMIT is displayed.
6.
1. MAIN MENU
> VEHICLE INFO
Select and confirm.
2. Select WARNINGS.
3. Confirm selection.
NO WARNING is displayed if the
vehicle is in perfect condition. Any
warning messages which are
present are displayed.
4. Press repeatedly to display the
warnings one after the other.
5. Confirm selection.
VEHICLE INFO menu is displayed.
134 Multi-Purpose Display and Instruments
Displaying status of level control
The ground clearance of vehicles equipped with
level control is shown in the LEVEL menu.
Note on operation
The level control is adjusted by means of the
rocker switch behind the gearshift lever in the
centre console.
f For information on level control and
height adjustment:
Please observe the chapter “AIR SUSPENSION
WITH LEVEL CONTROL AND HEIGHT ADJUST-
MENT” on Page 202.
Displaying status of locks/
reduction
The selected driving programmes for Low Range/
High Range as well as the engaged locks can be
displayed.
Note on operation
The driving programmes are set by means of the
rocker switch behind the gearshift lever in the
centre console.
f For information on the programmes for Off
Road and On Road driving and engaging locks/
reduction:
Please observe the chapter “DRIVING
PROGRAMMES FOR ON-ROAD AND OFF-ROAD
DRIVING” on Page 184.
6.
1. MAIN MENU
> VEHICLE INFO
Select and confirm.
2. Select LEVEL.
3. Confirm selection.
The current level settings are
displayed.
4. Confirm selection.
VEHICLE INFO menu is displayed.
5.
1. MAIN MENU
> VEHICLE INFO
Select and confirm.
2. Select LOCKS/REDUCT.
3. Confirm selection.
The current settings for
– Longitudinal lock on/off
– Reduction on/off
– Transverse axle differential lock
on/off
are displayed.
4. Confirm selection.
VEHICLE INFO menu is displayed.
Multi-Purpose Display and Instruments 135
Displaying average consumption Setting Tyre Pressure Monitoring
Safety notes!
Despite the advantages offered by Tyre
Pressure Monitoring, it is still the driver’s
responsibility to update the settings in the
multi-purpose
display and maintain the pressures in the
tyres. Low tyre pressure reduces the road
safety of the vehicle and destroys the tyre
and wheel.
f When a flat tyre has been displayed, stop in a
suitable place and check the tyres for damage.
If necessary, remedy the damage with tyre
sealant or fit the spare wheel.
f Do not by any means continue to drive with
leaking tyres.
f Sealing the tyre with the tyre sealant is only an
emergency repair so you can drive to the next
workshop.
The maximum permitted speed is 80 km/h
(50 mph).
f Defective tyres must be immediately replaced
by a specialist workshop.
Tyre repairs are not permissible under
any circumstances.
f Do not drive with tyres whose tyre pressure
drops again in a short period of time. Have
tyres checked by a specialist workshop.
f If Tyre Pressure Monitoring is defective
(e.g. defective wheel transmitters), contact a
specialist workshop immediately and have the
damage repaired.
The tyre pressure will not be monitored by
defective Tyre Pressure Monitoring.
For information on warning messages on the
multi-purpose display: Please observe the
chapter “OVERVIEW OF WARNING MESSAGES”
on Page 151.
f Tyre Pressure Monitoring gives a warning
about tyre damage due to insufficient tyre
pressure as well as about a gradual loss of
pressure due to foreign objects. Tyre Pressure
Monitoring cannot warn you about tyre
damage that occurs suddenly (e.g. flat tyre
due to acute external effects).
f If a tyre pressure message is displayed,
correct the tyre pressure at the next opportu-
nity.
5.
1. MAIN MENU
> VEHICLE INFO
Select and confirm.
2. Select Ø CONSUM.
3. Confirm selection.
The average consumption is
displayed.
The displayed value is based on the
distance travelled since the last
reset to “zero”.
Resetting average consumption
4. Select RESET.
5. Press the ENTER button for longer
than 1 second.
The value is set to “- -.-”.
136 Multi-Purpose Display and Instruments
f Incomplete entries or selection of the wrong
tyres on the multi-purpose display affect
correct indication of warnings and messages.
The settings in the TYRE PRESSURE menu
must be updated after wheel changes, use of
a spare wheel or changes in vehicle loading.
f Use only the pressure differences shown in the
TYRE PRESSURE menu or from tyre pressure
messages or warnings when correcting the
tyre pressure.
f Tyres lose air over time without a tyre defect
being present. A tyre pressure warning will
then appear on the multi-purpose display.
Correct tyre pressure.
Functional description of Tyre Pressure
Monitoring
Tyre Pressure Monitoring continuously monitors
tyre pressure and tyre temperature on all four
wheels and warns the driver when the tyre
pressure is too low.
The display as well as the settings for Tyre
Pressure Monitoring take place on the multi-
purpose display in the sub-menu TYRE
PRESSURE.
However, the tyre pressure must still be set
manually on the wheel.
The deviations in the tyre pressures from the
required pressures are shown in the sub-menu
TYRE PRESSURE.
Example:
If the tyre pressure display shows “–0.3 bar
(4 psi)”, you must increase the tyre pressure by
0.3 bar (4 psi).
The tyre pressures to be monitored are fixed in the
Tyre Pressure Monitoring system and cannot be
changed.
The following settings must be made to permit
correct monitoring.
– Tyres
Select the type and size of the tyres fitted on
the vehicle.
– Load
Select the type of loading.
Note on operation
Settings can be made only when the vehicle is
stationary.
f For information on tyres and wheels:
Please observe the chapter “TYRES AND
WHEELS” on Page 292.
Multi-Purpose Display and Instruments 137
Setting the tyre type and size
The settings of the multi-purpose display must be
updated after changing wheels or tyres on the
vehicle.
The tyre type and tyre size must be selected even
if the settings for the new set of wheels are the
same as for the old wheels.
After driving off, the system starts to teach the
wheels and wheel positions on the vehicle. The
tyre pressure warning light on the speedometer
lights up during this time, and no current tyre
pressure information is available on the displays.
Note
Information on the tyre size and type can be found
on the tyre sidewall.
f For further information on the details on the
tyre sidewall:
Please observe the chapter “INSCRIPTION ON
RADIAL TYRE” on Page 297.
Note on operation
Before fitting tyres approved by Porsche with a
size which is not already stored in the multi-
purpose display, the missing information should
be supplemented in the multi-purpose display.
f Consult a qualified specialist workshop. We
recommend that you use a Porsche partner for
this work since these are staffed with trained
personnel and have the necessary parts and
tools.
6.
1. MAIN MENU
> TYRE PRESS.
> SETTINGS
Select and confirm.
2. Select TYRES.
3. Confirm selection.
The TYRE TYPE list is displayed.
4. Select tyre type (e.g. SUMMER).
The list with the possible tyre
sizes (e.g. for the selection
SUMMER) is displayed.
5. Select tyre size (e.g. 18 inch).
6. Confirm selection.
The current settings are displayed.
138 Multi-Purpose Display and Instruments
Warning!
Risk of accident due to excessive speed.
f Always observe the permissible maximum
speed of the respective tyre.
f A sticker showing the maximum permissible
speed must be placed in the driver’s field of
vision if the maximum permissible speed of the
tyres is lower than the maximum permissible
speed of the vehicle.
Observe the country-specific laws.
The speed code letter indicates the maximum
permissible speed for the tyre.
f For further information on the details on the
tyre sidewall and the speed code letter:
Please observe the chapter “INSCRIPTION ON
RADIAL TYRE” on Page 297.
Setting vehicle loading and adjusting tyre
pressure
The tyre pressure must be adjusted according to
the vehicle load.
A distinction is made between two types of
loading:
– Partial load
up to 3 people and 21 kg of luggage
– Full load
more than 3 people and 22 kg of luggage
7.
1. MAIN MENU
> TYRE PRESS.
> SETTINGS
Select and confirm.
2. Select LOAD.
3. Confirm selection.
The LOAD menu is displayed.
Select corresponding load type
(e.g. FULL LOAD).
4. Confirm selection.
The set load status is shown.
Deviations from the required pressure are shown
in the sub-menu MAIN MENU > TYRE PRESSURE
> SETTINGS (filling information).
f Correct the tyre pressure according to this
information.
Multi-Purpose Display and Instruments 139
“Flat tyre” warning
The warning threshold for output of this warning
message is speed-dependent.
At a speed of below 160 km/h (100 mph), this
warning indicates a pressure loss of at least
0.5 bar (7 psi); at a speed of above 160 km/h
(100 mph), the warning indicates a pressure loss
of at least 0.4 bar (6 psi).
The message indicates the wheel in which the
pressure loss has been detected.
The deviation from the required pressure is
displayed for the corresponding wheel.
The tyre pressure warning light on the speedom-
eter lights up in addition to the warning message.
f The warning message can be acknowledged
while driving.
To do this, press the ENTER button on the
wiper stalk. The tyre pressure warning light on
the speedometer remains lit.
The measure display SELECTION AFTER
WARNING appears only after the ignition is
switched back on again.
The display shows: SELECTION AFTER WARNING
1. Stop the vehicle in a suitable place.
2. Check the indicated wheel for damage.
3. Fill the tyre or change the wheel, as appro-
priate.
– Adding air
(Example: If the tyre pressure display shows
“–0.4 bar (6 psi)”, you must increase the tyre
pressure by 0.4 bar (6 psi)).
On vehicles without air suspension:
Please observe the chapter “INFLATING TYRES
ON VEHICLES WITHOUT LEVEL CONTROL” on
Page 313.
On vehicles with air suspension:
Please observe the chapter “INFLATING TYRES
ON VEHICLES WITH LEVEL CONTROL” on
Page 315.
or
– Changing wheel with spare wheel or
collapsible spare wheel
For information on jacking up the vehicle:
Please observe the chapter “RAISING VEHICLE
WITH THE JACK” on Page 305.
For information on changing a wheel:
Please observe the chapter “CHANGING A
WHEEL” on Page 308.
or
– Sealing with tyre sealant.
For information on handling and filling the
sealant: Please observe the chapter “TYRE
SEALANT” on Page 303.
4. Switch ignition on again.
The “Flat tyre” warning first appears again on
the multi-purpose display. The display changes
to SELECTION AFTER WARNING after a few
seconds.
5. Select the action which has been carried out
on the vehicle on the display with the rocker
switch.
– ADD AIR or
– WHEEL CHANGE > SPARE WHEEL > Spare
wheel type or
– SEALING SET
6. Press the ENTER button.
140 Multi-Purpose Display and Instruments
Notes
The spare wheel and collapsible spare wheel are
not equipped with wheel transmitters and are not
monitored by Tyre Pressure Monitoring.
If a collapsible spare wheel or tyre sealant is used,
a warning reminder appears on the multi-purpose
display if the speed limit of 80 km/h (50 mph) is
exceeded.
Note on operation
If you do not confirm a selection or confirm a
selection without carrying out the task described
for this selection, this will affect correct indication
of warnings and messages.
Depending on the selection made, a corre-
sponding message will appear when the ignition is
switched on, when driving off or while driving.
For further information on warning messages on
the multi-purpose display:
Please observe the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 151.
“Tyre pressure too low” message
This message indicates pressure loss of at least
0.3 bar (4 psi).
The message indicates the wheel in which the
pressure loss has been detected. The deviation
from the required pressure is displayed for the
corresponding wheel.
The message appears only when the vehicle is
stationary. It appears for the first time when the
ignition is switched off and then each time the
ignition is switched on until the tyre pressure has
been corrected to the required value.
The message is shown for 10 seconds on the
multi-purpose display. It can be suppressed
immediately by pressing the ENTER button.
f Check the tyre pressure at the next opportu-
nity and fill the tyres.
Example: If the tyre pressure display shows
“–0.3 bar (4 psi)”, you must increase the tyre
pressure by 0.3 bar (4 psi).
The spare wheel and collapsible spare wheel are
not equipped with wheel transmitters and are not
monitored by Tyre Pressure Monitoring.
Wheel change (without warning)
The settings of the multi-purpose display must be
updated after changing wheels or tyres on the
vehicle.
Please observe the chapter “SETTING THE TYRE
TYPE AND SIZE” on Page 137.
Setting spare wheel/sealant
(without warning)
If you have fitted a spare wheel or collapsible
spare wheel or used tyre sealant without being
requested to do so by a “Flat tyre” warning on the
multi-purpose display, you must subsequently
update the settings in the TYRE PRESSURE sub-
menu.
Multi-Purpose Display and Instruments 141
Setting spare wheel.
The spare wheel is not equipped with a wheel
transmitter and is not monitored by Tyre Pressure
Monitoring. The tyre pressure warning light lights
up on the speedometer when the ENTER button is
pressed. The value “_._” is displayed in the sub-
menu TYRE PRESSURE (filling information) at the
position of the spare wheel.
The reminder SPARE WHEEL/SEALING SET
OPERATION? appears each time the ignition is
switched on. For information on spare wheel/
sealing set operation: Please observe the chapter
“NOTE ON OPERATION FOR SPARE WHEEL/
SEALING SET OPERATION” on Page 142.
Note
f The spare wheel must be used only over short
distances.
For information on handling and fitting/
removing the spare wheel: Please observe the
chapter “SPARE WHEEL” on Page 317.
Setting collapsible spare wheel.
The collapsible spare wheel is not equipped with a
wheel transmitter and is not monitored by Tyre
Pressure Monitoring. The tyre pressure warning
light lights up on the speedometer when the
ENTER button is pressed. The value “_._” is
displayed in the sub-menu TYRE PRESSURE (filling
information) at the position of the collapsible
spare wheel.
A warning appears on the multi-purpose display if
the speed limit of 80 km/h (50 mph) is exceeded.
The reminder SPARE WHEEL/SEALING SET
OPERATION? appears each time the ignition is
switched on.
For information on spare wheel/sealing set opera-
tion: Please observe the chapter “NOTE ON
OPERATION FOR SPARE WHEEL/SEALING SET
OPERATION” on Page 142.
1. MAIN MENU
> TYRE PRESS.
> SETTINGS
> TYRES
> SPARE WHEEL
Select and confirm.
2. Select SPARE WHEEL.
3. Confirm selection.
The display automatically returns to
the TYRE PRESSURE sub-menu
(filling information).
The required tyre pressures
are displayed here.
Select BACK.
4. Confirm selection.
The basic display appears.
1. MAIN MENU
> TYRE PRESS.
> SETTINGS
> TYRES
> SPARE WHEEL
Select and confirm.
2. Select COLLAP. WHEEL.
3. Confirm selection.
The required pressure and speed
limit for the collapsible spare wheel
are displayed.
142 Multi-Purpose Display and Instruments
Note
The collapsible spare wheel must be used only
over short distances.
For information on handling the collapsible spare
wheel: Please observe the chapter “COLLAPSIBLE
SPARE WHEEL” on Page 311.
Setting tyre sealant/sealing set
f Inflate tyres according to the displayed
pressure differences.
A warning appears on the multi-purpose display if
the speed limit of 80 km/h (50 mph) is exceeded.
The reminder SPARE WHEEL/SEALING SET
OPERATION? appears each time the ignition is
switched on.
For information on spare wheel/sealing set opera-
tion: Please observe the chapter “NOTE ON
OPERATION FOR SPARE WHEEL/SEALING SET
OPERATION” on Page 142.
Note
Use tyres repaired with sealant only over short
distances.
For information on handling and filling the sealant:
Please observe the chapter “TYRE SEALANT” on
Page 303.
Note on operation for spare wheel/sealing
set operation
Each time the ignition is switched on,
the reminder SPARE WHEEL/SEALING SET
OPERATION? appears for approx. 10 seconds if a
spare wheel type (spare wheel, collapsible spare
wheel or sealing set) has been set.
f Set the fitted wheel set with tyre type and tyre
size.
Please observe the chapter “SETTING THE
TYRE TYPE AND SIZE” on Page 137.
Note on operation
The reminder SPARE WHEEL/SEALING SET
OPERATION? goes out automatically after approx.
10 seconds if no selection is made during this
time. The original selection “YES” is then
maintained.
1. MAIN MENU
> TYRE PRESS.
> SETTINGS
> TYRES
> SPARE WHEEL
Select and confirm.
2. Select SEALING SET.
3. Confirm selection.
The display automatically returns to
the TYRE PRESSURE sub-menu
(filling information).
1. Select YES or NO:
– YES if a spare wheel, collapsible
spare wheel or tyre sealant is still
being used.
– NO if the spare wheel, collapsible
spare wheel or tyre sealant has
been removed.
2. Confirm selection.
The selected item is then accepted.
The current settings are displayed if
NO is selected.
Multi-Purpose Display and Instruments 143
In the event of faults, Tyre Pressure Monitoring
cannot monitor the tyre pressure. A distinction is
made between partial monitoring and inactive
system.
In the case of partial monitoring, the warning light
lights up on the instrument panel. No message is
output on the multi-purpose display.
If Tyre Pressure Monitoring is not active, the
warning light lights up on the instrument panel and
a corresponding message is output on the multi-
function display.
The warning light goes out as soon as all faults
have been remedied.
Tyre Pressure Monitoring switches to partial
monitoring if:
– there are up to two wheel transmitters not
present or faulty (e.g. a spare wheel or collaps-
ible spare wheel is fitted that does not have a
wheel transmitter).
In the event of partial monitoring, the value “_._” is
displayed in the sub-menu TYRE PRESSURE (filling
information) at the position of the faulty or missing
wheel transmitter.
Tyre Pressure Monitoring is not active in the
following cases:
– Tyre Pressure Monitoring is faulty,
– at least three wheel transmitters for Tyre
Pressure Monitoring are faulty or not present,
– temporarily after changing a wheel,
– too many wheel transmitters have been
detected,
– there is external interference by other radio
sources, e.g. wireless headphones,
– tyre temperatures are too high.
f For information on messages on the multi-
purpose display:
Please observe the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 151.
Notes on tyre pressure
Pressure increase as the result of
temperature increase
In accordance with physical principles,
the tyre pressure changes as the temperature
changes. The tyre pressure increases or
decreases by around 0.1 bar (1.5 psi) for every
10 °C change in temperature.
Tyre pressure specifications
The tyre pressure must match the prescribed
value (required pressure).
You can find information on the tyre pressure for
cold tyres (20 °C):
– in the sub-menu TYRE PRESSURE (filling infor-
mation):
as a required pressure for each axle if Tyre
Pressure Monitoring has not yet been taught
the corresponding values,
– in the front left door aperture for each wheel,
– in the Technical Data chapter in this Driver’s
Manual: Please observe the chapter “TYRE
PRESSURES, COLD” on Page 367.
If Tyre Pressure Monitoring has been taught the
corresponding values, the deviations from the
required pressure are shown in the sub-menu
TYRE PRESSURE (filling information) independ-
ently of the tyre temperature. The correct tyre
pressure adjustment can be made for a wheel on
the basis of this display information even if the
tyres are warm.
Insufficient tyre filling pressure can cause tyres to
overheat when driving and thus be damaged –
even invisibly.
Hidden tyre damage is not eliminated by subse-
quently correcting the tyre pressure.
f For this reason, always make sure that the tyre
pressure is correct.
f For further information on maintenance and
care of tyres and wheels:
Please observe the chapter “TYRES AND
WHEELS” on Page 292.
Faults in Tyre Pressure Monitoring
144 Multi-Purpose Display and Instruments
Switching off passenger compart-
ment monitoring and inclination
sensor on the multi-purpose
display
The passenger compartment monitoring system
and the inclination sensor (protection against
towing) can be temporarily deactivated in the
ALARM sub-menu.
When the doors are locked again, the passenger
compartment monitoring system and inclination
sensor are activated once more.
f Further important information concerning this
topic can be found in a separate chapter:
Please observe the chapter “SWITCHING OFF
PASSENGER COMPARTMENT MONITORING
SYSTEM AND INCLINATION SENSOR” on
Page 263.
Note on operation
f Comfort settings can be made only when the
vehicle is stationary.
Switching passenger compartment
monitoring on/off
The alarm is triggered if motion is detected in the
interior with the doors closed (e.g. if a window is
broken in a theft).
Switching inclination sensor on/off
The alarm is triggered if the vehicle is raised
markedly at one end with the doors locked
(e.g. theft with a breakdown truck).
1. MAIN MENU
> SETTINGS
> COMFORT
> ALARM
Select and confirm.
2. Select INTERIOR.
3. Confirm selection.
Monitoring is activated
Monitoring is deactivated
1. MAIN MENU
> SETTINGS
> COMFORT
> ALARM
Select and confirm.
2. Select ANGLE.
3. Confirm selection.
Inclination sensor is activated
Inclination sensor is deactivated
Multi-Purpose Display and Instruments 145
Synchronous adjustment of door
mirrors
Note on operation
Comfort settings can be made only when the
vehicle is stationary.
When this function is active, the mirrors move
simultaneously and in the same direction.
Changing settings for opening and
locking the vehicle
Note on operation
Comfort settings can be made only when the
vehicle is stationary.
You can set different variants of locking and
unlocking the doors and the rear lid as well as the
check-back signal when locking and unlocking the
vehicle and save them on the respective remote
control.
1. Using the rocker switch and the
ENTER button on the wiper stalk, select
MAIN MENU > SETTINGS > COMFORT >
DOOR OPENING
2. Set the desired function.
3. Switch ignition off.
4. Close the driver’s door.
5. Press button on the vehicle key.
The settings are now stored on this vehicle
key.
Setting door unlocking
Door unlocking can be set on an individual basis.
1. MAIN MENU
> SETTINGS
> COMFORT
> MIRRORS
Select and confirm.
2. Select SYNCH.
3. Confirm selection.
SYNCHRONOUS ADJUSTMENT
is activated
SYNCHRONOUS ADJUSTMENT
is deactivated
1. MAIN MENU
> SETTINGS
> COMFORT
> DOOR OPENING
> DOORS
Select and confirm.
146 Multi-Purpose Display and Instruments
Note on operation
If the unlocking button on the remote control
is pressed a second time within 2 seconds, all
vehicle doors are unlocked independently of the
setting.
Setting door opening signal
If the signal function is active, door unlocking and
locking are confirmed by the hazard warning lights
flashing.
Setting rear lid locking
When the TAILGATE function is active, rear access
(rear lid, rear window and spare wheel bracket) is
included in the central locking system.
Access is possible when the vehicle is stationary
and unlocked.
At speeds higher than 6 km/h (4 mph), release is
blocked until a door is opened with the vehicle
stationary.
When the TAILGATE function is deactivated,
access is only possible using button on the
remote control.
2. Select one of the three options:
– SINGLE DOOR
Only the driver’s door is unlocked.
The door on the access side is
unlocked on vehicles equipped with
Porsche Entry & Drive.
– VEH. SIDE
Both doors on the driver’s side are
unlocked.
The doors on the access side are
unlocked on vehicles equipped with
Porsche Entry & Drive.
– ALL
All doors are unlocked.
3. Confirm selection.
1. MAIN MENU
> SETTINGS
> COMFORT
> DOOR OPENING
> SIGNAL
Select and confirm.
2. Select TURN SIGNALS.
3. Confirm selection.
Signal is activated.
Signal is deactivated.
1. MAIN MENU
> SETTINGS
> COMFORT
> DOOR OPENING
Select and confirm.
2. Select TAILGATE.
3. Confirm selection.
Function is activated.
Function is deactivated.
Multi-Purpose Display and Instruments 147
Setting AUTO LOCK and AUTO UNLOCK
AUTO LOCK and AUTO UNLOCK variants
You can set 4 different variants of automatic door
locking (AUTO LOCK) and automatic door
unlocking (AUTO UNLOCK).
Doors locked using AUTO LOCK can always be
opened by pulling the inner door handle twice
regardless of the setting for door unlocking.
Option 1:
AUTO LOCK off and AUTO UNLOCK off
The doors do not lock and unlock automatically.
Option 2:
AUTO LOCK on and AUTO UNLOCK off
Doors lock automatically when a speed of approx.
6 km/h (4 mph) is exceeded.
Option 3:
AUTO LOCK on and AUTO UNLOCK on
Doors lock automatically when a speed of approx.
6 km/h (4 mph) is exceeded.
On vehicles without Porsche Entry & Drive, the
doors are unlocked automatically when the
ignition key is withdrawn.
On vehicles equipped with Porsche Entry & Drive,
the doors are unlocked when the ignition is
switched off twice.
Option 4:
AUTO LOCK off and AUTO UNLOCK on
The doors do not lock automatically.
If the doors are locked with the central locking
system button:
On vehicles without Porsche Entry & Drive, the
doors are unlocked automatically when the
ignition key is withdrawn.
On vehicles equipped with Porsche Entry & Drive,
the doors are unlocked when the ignition is
switched off twice.
Setting lighting off delay
You can set the duration the lights remain on after
the vehicle is locked.
1. MAIN MENU
> SETTINGS
> COMFORT
> DOOR OPENING
Select and confirm.
2. Select AUTO LOCK or
AUTO UNLOCK.
3. Confirm selection.
Selection is activated.
Selection is deactivated.
1. MAIN MENU
> SETTINGS
> LIGHTS
Select and confirm.
2. Select OFF DELAY.
3. Confirm selection.
The set off delay time is now
active.
4. Select the time input field.
5. Confirm selection.
6. Set the off delay time
(Coming Home function):
The time is adjusted by pressing the
rocker switch.
Delay times of 15, 30 or 60 seconds
can be set.
7. Confirm selection.
148 Multi-Purpose Display and Instruments
Setting the clock
Note on operation
There is also a button on the instrument panel to
call the CLOCK menu:
Please observe the chapter “CLOCK” on
Page 120.
1. MAIN MENU
> SETTINGS
> CLOCK
Select and confirm.
2. Select xx:xx SET.
3. Confirm selection.
4. Select hours or minutes display.
5. Confirm selection.
The desired time can now be set.
6. Set the desired time:
The time is adjusted in hour or minute
increments by pressing the rocker
switch.
7. Confirm selection.
Selecting 12 h mode
8. Select 12 h-MODE.
9. Confirm selection.
12 h mode is activated
12 h mode is deactivated
Multi-Purpose Display and Instruments 149
Setting compass
The display is available only for vehicles equipped
with Porsche Radio CDR-23 and magnetic field
sensor.
If you drive your vehicle across the magnetic field
zone set on the multi-purpose display, you must
enter your current zone in the COMPASS menu
(see illustration).
1. MAIN MENU
> SETTINGS
> COMPASS
Select and confirm.
2. Select SET ZONE xx.
3. Confirm selection.
4. Select zone.
The setting is changed in increments
of 1 by pressing the rocker switch.
5. Confirm selection.
Calibrating compass
In rare cases, external disturbances may necessi-
tate calibration of the compass. The warning
message “CAL.” then appears on the multi-
purpose display.
f To calibrate the compass, follow the displayed
instruction DRIVE IN A FULL CIRCLE.
The display returns to the main menu after
successful calibration.
150 Multi-Purpose Display and Instruments
Changing language for displays
Note
Changing the language will affect the entire multi-
purpose display.
Changing units for displays
Available categories and units
– Speedometer:
km/h - km, mph - mls
– Consumption:
l/100 km, km/l, MPG (UK),
MPG (US)
– Temperature:
°C - CELSIUS, °F - FAHRENHEIT
– Tyre pressure:
bar, psi
Resetting display to factory
settings
All settings made (Clock, Comfort, Lights, Units,
Language) can be reset to the factory settings.
Note
All personal settings made up to this point will be
deleted by resetting to the factory settings.
1. MAIN MENU
> SETTINGS
> LANGUAGE
Select and confirm.
2. Select the desired language.
3. Confirm selection.
1. MAIN MENU
> SETTINGS
> UNITS
Select and confirm.
2. Select the desired category
(e.g. SPEEDOMETER).
3. Confirm selection.
4. Select the desired unit (e.g. MPH).
5. Confirm selection.
1. MAIN MENU
> SETTINGS
> FACTORY SET
Select and confirm.
2. Select RESET.
3. Confirm selection.
Multi-Purpose Display and Instruments 151
Overview of warning messages
If a warning message appears, always refer to the corresponding chapters in this Driver’s Manual.
Warning messages are issued only if all measurement preconditions are met.
Therefore, check all fluid levels regularly – in particular, always check the engine oil level after refuelling.
Light on
instrument
panel
Warning message
on the multi-purpose display
Meaning/measures
Steering faulty Steering lock engaged.
Consult a qualified specialist workshop.*
Ignition lock faulty Do not continue driving.
Consult a qualified specialist workshop.*
System fault Consult a qualified specialist workshop.*
Key not recognised in vehicle Make sure that you have the remote control with you.
Turn ignition key to the left
for 2 seconds
To lock the steering, turn the ignition key to the left and hold for
2 seconds.
Key: replace battery Replace the remote-control battery.
Move steering wheel Turn the steering wheel so that the steering wheel lock can
engage/disengage.
Key not found Make sure that you have the remote control with you.
Move selector lever
to position P
Tiptronic S: the vehicle could roll away.
The ignition key can be withdrawn only in Tiptronic selector lever
position P.
Press brake pedal Apply the brake when starting.
Move selector lever
to position P or N
Tiptronic S: the vehicle can be started only in position P or N.
152 Multi-Purpose Display and Instruments
Depress clutch Manual transmission: depress clutch pedal when starting.
Immobilizer active Consult a qualified specialist workshop.*
Check hitch Ball head is not in its final position.
Press rocker switch until the final position is reached.
Warning Hitch Stop at a suitable place. Do not continue driving.
Ball head is not in its final position.
Press rocker switch until the final position is reached.
Check left static cornering
light
Check bulb.
Check right static cornering
light
Check bulb.
Check dynamic cornering light Consult a qualified specialist workshop.*
If the warning message appears, the high beam indicator light
on the speedometer flashes additionally.
Check dipped beam Check bulb.
Check trailer lights Check bulb.
Check direction indicators Check bulb.
Check high beam Check bulb.
Check licence plate light Check bulb.
Check fog lights Check bulb.
Check reversing lights Check bulb.
Light on
instrument
panel
Warning message
on the multi-purpose display
Meaning/measures
Multi-Purpose Display and Instruments 153
Check front side lights Check bulb.
Check headlight beam adjustment Consult a qualified specialist workshop.*
Daytime driving lights off Daytime driving lights switch off when the engine is shut off.
Switch on lights if necessary.
System fault headlamp Consult a qualified specialist workshop.*
Airbag faulty.
Consult a qualified specialist workshop.*
Seat belt Fasten seat belt.
Caution Flat tyre
Check tyres
Tyre Pressure Monitoring detects a pressure loss of at least
0.4 bar (6 psi) or a larger leak.
Stop in a suitable place and check tyres.
Change wheel if necessary.
Check spare wheel
Req. pressure:
3.4 bar / 50 psi
Appears about every 6 months.
Check if the pressure of the fitted spare wheel matches the
required pressure manually, as it is not monitored electronically.
Tyre pressure too low Add air Tyre Pressure Monitoring detects a pressure loss of at least
0.3 bar (4 psi).
Correct tyre pressure at the next opportunity.
Collap. wheel/sealing set
max. 80 km/h / 50 mph
Observe maximum permitted speed.
Collap. wheel
Req. pressure: 3.5 bar/51 psi
Max. 80 km/h / 50 mph
Information on driving with a collapsible spare wheel
after selection in
spare wheel menu.
Observe maximum speed of max. 80 km/h or 50 mph and
required pressure of 3.5 bar or 51 psi.
Light on
instrument
panel
Warning message
on the multi-purpose display
Meaning/measures
154 Multi-Purpose Display and Instruments
System not active Tyre Pressure Monitoring faulty.
Consult a qualified specialist workshop.*
Select new set of wheels in the Tyre pressure menu after
changing the wheels.
System not active
Brief disturbance
External interference (e.g. wireless headphones) or excessive
temperature (over 120 °C) at the wheel transmitters. Tyre
Pressure Monitoring will reactivate itself automatically.
System not active Too many
wh. transmitters
Tyre Pressure Monitoring detects more than 4 wheel
transmitters (e.g. winter wheels in the luggage compartment).
Tyre Pressure Monitoring will reactivate itself after the additional
wheel transmitters have been removed.
No monitoring System learning After the tyre type and size are selected in the Tyre pressure
menu, Tyre Pressure Monitoring re-teaches the tyres.
Wheel change?
Make new selection
The tyre type and size of the changed tyres have not been
updated for Tyre Pressure Monitoring.
The display changes when the vehicle is stationary:
Select corresponding tyre type and tyre size.
When vehicle stops: hit selection The message appears after driving off if the warning “Flat tyre”
has been cleared but the selection on the display SELECTION
AFTER WARNING has not been made properly.
Make selection on the multi-purpose display when the vehicle is
stationary.
Engine temperature too high Coolant or engine oil temperature is too high.
Switch engine off and let it cool.
Check coolant or engine oil level. Add more coolant or engine
oil if necessary.
Check coolant level Switch engine off and let it cool.
Check coolant level. Add coolant if necessary.
Light on
instrument
panel
Warning message
on the multi-purpose display
Meaning/measures
Multi-Purpose Display and Instruments 155
Warning Battery/generator Stop in a suitable place and switch engine off.
Do not continue driving.
Have the fault remedied at a qualified specialist
workshop.*
Start engine The battery discharges if the engine is not running and loads are
switched on.
Start the vehicle or switch the loads off.
Electric load switch-off Vehicle electrical system is overloaded. Certain loads
(e.g. heated rear window, seat heating) will be switched off.
Please refuel
Add washer fluid
Oil level monitoring Failure Consult a qualified specialist workshop.*
Check oil level Check the oil level using the oil dipstick as soon as possible and
add engine oil if necessary.
Oil pressure too low Immediately stop in a suitable place and switch engine off.
Do not continue driving.
Check engine oil level. Add oil if necessary.
Do not continue driving if the warning light comes on even when
the oil level is correct. Have the fault remedied at a qualified
specialist workshop.*
Oil pressure monitoring Failure Consult a qualified specialist workshop.*
Service in 3000 km/mls Service indicator
Bring the vehicle in for service no later than after the distance
shown has been covered. However, it is the intervals in the
“Guarantee and Maintenance” booklet that are decisive.
Service now Service indicator
Have your vehicle serviced at a qualified specialist workshop.*
Light on
instrument
panel
Warning message
on the multi-purpose display
Meaning/measures
156 Multi-Purpose Display and Instruments
Brake pads Have the brake pads changed immediately.
Consult a qualified specialist workshop.*
Warning Brake proportioning Stop immediately in a suitable place. Do not continue driving.
Have the fault remedied at a qualified specialist
workshop.*
ABS failure Drive carefully. Have the fault remedied at a qualified specialist
workshop.*
PSM failure Drive carefully. Have the fault remedied at a qualified specialist
workshop.*
Warning Brake fluid level Stop immediately in a suitable place. Do not continue driving.
Have the fault remedied at a qualified specialist
workshop.*
Parking brake Parking brake not released.
PSM on Porsche Stability Management was switched on.
PSM off Porsche Stability Management was switched off.
PHC unavailable The Porsche Drive-off Assistant (manual transmission) is not
available.
Brake booster faulty Greater brake pedal force necessary.
Drive carefully to the nearest qualified specialist workshop.*
Chassis Sport Current setting of Porsche Active Suspension Management
Chassis Normal Current setting of Porsche Active Suspension Management
Chassis Comfort Current setting of Porsche Active Suspension Management
Light on
instrument
panel
Warning message
on the multi-purpose display
Meaning/measures
Multi-Purpose Display and Instruments 157
Chassis system faulty Handling may be affected. Adapt your speed to the changed
conditions. Have the fault remedied at a qualified specialist
workshop.*
Warning Chassis system The side tilt of the vehicle is significantly greater when
cornering. Drive carefully at an appropriate speed to the nearest
qualified specialist workshop.*
Warning Chassis system Stop at a suitable place. Do not continue driving.
Have the fault remedied at a qualified specialist
workshop.*
Chassis system faulty Drive carefully to the nearest qualified specialist workshop.*
Spare wheel filling Collapsible spare wheel is being filled by level-control
compressor.
Do not drive off!
Regulation switched off Level control has been switched off (to jack up the vehicle).
Not permissible The prerequisites for setting the desired level have not been
met.
Pressure accumulator charging Level control temporarily unavailable.
Four-wheel dr. system faulty Have the fault remedied at a qualified specialist
workshop.*
Shift not possible;
speed too high
Tiptronic S: When changing between Low Range and High
Range, the limit speed (off-road programme) must not be
exceeded.
Shift possible only in Neutral Tiptronic S: The Tiptronic selector lever must be in position N
when changing between Low Range and High Range.
Possible only when stopped in
neutral with brake
Manual transmission: The vehicle must be stationary, the brakes
must be applied and the gearshift lever must be in the Neutral
position when changing between Low Range and High Range.
Light on
instrument
panel
Warning message
on the multi-purpose display
Meaning/measures
158 Multi-Purpose Display and Instruments
Warning Parking lock! Apply
parking brake!
Do not continue driving. Apply the parking brake.
Have the fault remedied at a qualified specialist
workshop.*
Failure sport mode Have the fault remedied at a qualified specialist
workshop.*
Sport mode only usable
without reduction
Sport mode cannot be selected when the off-road driving
programme (Low Range) is engaged.
Limit exceeded The set speed limit has been exceeded.
Spare wheel is not locked.
Danger of injury and damage. Before driving off
always lock the spare wheel correctly.
Driver’s door open
All unlocked doors and lids are displayed when the vehicle
exceeds 3 km/h (2 mph).
Passenger’s door open
All unlocked doors and lids are displayed when the vehicle
exceeds 3 km/h (2 mph).
Rear left door open
All unlocked doors and lids are displayed when the vehicle
exceeds 3 km/h (2 mph).
Rear right door open
All unlocked doors and lids are displayed when the vehicle
exceeds 3 km/h (2 mph).
Bonnet open
All unlocked doors and lids are displayed when the vehicle
exceeds 3 km/h (2 mph).
Light on
instrument
panel
Warning message
on the multi-purpose display
Meaning/measures
Multi-Purpose Display and Instruments 159
* We recommend that you use a Porsche partner for this work since these are staffed with trained personnel and have the necessary parts and tools.
Rear lid open.
All unlocked doors and lids are displayed when the vehicle
exceeds 3 km/h (2 mph).
Rear window open
All unlocked doors and lids are displayed when the vehicle
exceeds 3 km/h (2 mph).
System fault Several systems may have failed. Have the fault remedied at a
qualified specialist workshop.*
Light on
instrument
panel
Warning message
on the multi-purpose display
Meaning/measures
160 Multi-Purpose Display and Instruments
Mobile phones and 2-way radios
f Read the operating instructions of the tele-
phone manufacturer before putting a tele-
phone into operation.
f Please observe the applicable national regula-
tions regarding telephone calls during driving.
Safety notes!
f For reasons of road safety, only telephone
using the hands-free unit.
f To prevent any possible risk to health:
Use telephones or 2-way radios with integral
radio antennas in the vehicle only if an external
antenna is connected.
Installation of mobile communications systems
(car telephone, 2-way radio, etc.) requires
approval and should be performed only according
to Porsche installation specifications in a
specialist workshop.
The transmission power must not exceed
10 W.
The devices must possess a type approval for
your vehicle and have an „e“ symbol.
If you should require equipment with transmission
power values greater than 10 W, please consult a
qualified specialist workshop for this purpose.
They are familiar with the technical requirements
for installing devices of this kind.
Incorrectly installed equipment or antennas as well
as telephones and 2-way radios without external
antenna may interfere with the vehicle electronics
as a result of radio transmission.
f Use telephones or 2-way radios only with a
connected external antenna.
Hands-free microphone
Hands-free microphones installed at the factory
must be adapted to the type of telephone in use.
Your Porsche partner will be pleased to advise
you.
Reception quality
The reception quality of your telephone will change
continuously as you drive.
Interference from buildings, terrain and the
weather is unavoidable.
Comprehensibility can be adversely affected by
external noise (e.g. engine and wind noise),
particularly when hands-free equipment is used.
Porsche Communication
Management (PCM)
f Refer to the separate operating instructions
before putting the PCM into operation.
When put into operation for the first time, a dis-
tance of approx. 5 km (3 miles) must be driven in
order for the navigation system to complete the
process of fine calibration. The same applies
when the tyres are changed (e.g. summer/winter
tyres) or new tyres fitted. Full location accuracy is
not yet achieved during the fine-calibration
process.
If the vehicle has been transported (e.g. by ferry
or car train), the system may take a few minutes
after being switched on before it determines the
current location.
Serious tyre slip (e.g. spinning wheels on snow)
may result in temporarily inaccurate navigation.
When the battery has been disconnected, it may
take up to 15 minutes before the navigation
system is operational again.
Multi-Purpose Display and Instruments 161
Radio
f Refer to the separate radio operating instruc-
tions before putting into operation.
The reception conditions for your car radio
change continuously as you drive. Interference
from buildings, terrain and the weather is
unavoidable. FM stereo reception is particularly
susceptible to varying reception conditions. To
reduce interference, you can switch the radio to
mono mode or tune to a different FM stereo
station.
Electronic accessories should only be installed
after purchasing vehicle by a qualified specialist
workshop. Accessories which have not been
tested and approved by Porsche may impair radio
reception.
Fire extinguisher
If the vehicle is equipped with a fire extinguisher, it
is mounted underneath the left or right front seat,
depending on equipment level.
Fire extinguisher under the left front seat
f To remove the fire extinguisher in case of an
emergency, hold the fire extinguisher with one
hand, and press the PRESS button on the fire
extinguisher holder with the other hand
(arrow).
Fire extinguisher under the right front seat
f Take the fire extinguisher out of the drawer
under the seat.
Notes
f Pay attention to the final inspection date on the
fire extinguisher. If the fire extinguisher is used
after its inspection interval has elapsed, it may
not function properly.
f Follow the operating instructions for the fire
extinguisher.
f The fire extinguisher should be checked for
operation by a specialist workshop every
1-2 years.
f After use, have the fire extinguisher refilled.

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot