2002-2010 Porsche Cayenne SUV Parking -> Garage door opener User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Parking -> Garage door opener for Your Porsche Cayenne SUV First Generation (2002-2010)

Parking 259
A - Programmable keypad
B - Light-emitting diode for status identification
Garage door opener
The garage door opener of your Porsche replaces
up to three original hand-held transmitters used to
operate various devices (e.g. garage door, gate to
the property, alarm system).
You have the option of assigning up to 3 different
signals to the keys on keypad A.
Warning!
Risk of accident when using the garage door
opener if persons, animals or objects are
within the range of movement of the equip-
ment that is being operated.
f When using the garage door opener, ensure
that no persons, animals or objects are within
the range of movement of the equipment that
is being operated.
f Observe the safety notes for the original hand-
held transmitter.
Notes on operation
f Always use the garage door opener in the
direction of travel.
Otherwise, range restrictions cannot be ruled
out.
f Before selling the vehicle, delete the
programmed signals of the garage door
opener on the keypad.
f Please read the instructions for the original
hand-held transmitter to find out whether the
original transmitter is equipped with fixed or
changeable code.
Deleting programmed signals from the
keys
This process deletes the standard codes set at
the factory. Do not repeat this process if you
would like to assign additional signals to the keys.
f Keep the two outer buttons of keypad A
depressed for approximately 20 seconds until
light-emitting diode B begins to flash.
260 Parking
Assigning garage door opener signal to
key with fixed code system
1. Please follow the operating instructions for the
original hand-held transmitter.
2. The standard codes set at the factory must be
deleted before programming for the first time.
3. Point the original transmitter at the marked
position.
4. Press the button of the original hand-held trans-
mitter and the button to be allocated on the
keypad simultaneously (see illustration).
5. Keep both buttons depressed until light-
emitting diode B starts to flash (first slowly and
then quickly).
Only release both buttons when light-emitting
diode B flashes quickly.
The rapidly flashing light-emitting diode B
confirms that the new signal has been
programmed successfully.
6. Repeat steps 3 to 5 to assign signals to the
other buttons.
Assigning garage door opener signal to
key with changeable code system
1. Please follow the operating instructions for the
original hand-held transmitter.
2. The standard codes set at the factory must be
deleted before programming for the first time.
3. Point the original transmitter at the marked
position.
4. Press the button of the original hand-held trans-
mitter and the button to be allocated on the
keypad simultaneously.
5. Keep both buttons depressed until light-
emitting diode B starts to flash (first slowly and
then quickly).
Only release both buttons when light-emitting
diode B flashes quickly.
The rapidly flashing light-emitting diode B
confirms that the new signal has been
programmed successfully.
6. To synchronise the system:
Press the programming button on the receiver
for the garage door drive.
Afterwards, you usually have approx.
30 seconds to initiate step 7.
7. Press the button to be assigned on the keypad
twice (for some devices you must press the
key on the keypad a third time to complete the
setting process).
8. Repeat steps 3 to 7 to assign signals to the
other buttons.
Note
f Please consult a Porsche partner if you have
not been able to successfully assign signals to
the buttons even though you have carefully
followed the instructions in this chapter and
the operating instructions for the original hand-
held transmitter. Your Porsche Partner has a
list of all garage door opener signals that can
be taught.
Parking 261
Reprogramming an individual button of
keypad A
1. Press the button of keypad A to be repro-
grammed. Do not release the buttons before
step 4 is executed.
2. When the light-emitting diode B flashes slowly
(after approximately 20 seconds), point the
original transmitter at the position marked.
3. Press the button of the original hand-held
transmitter and keep it depressed.
4. The light-emitting diode B first flashes slowly
and then more quickly.
Only release both buttons when light-emitting
diode B flashes quickly.
Operating the garage door opener
f Press the corresponding button on keypad A.
Light-emitting diode B lights up during signal
transfer.

Related Topics

Popular Owner Manuals