2025-2026 Porsche Taycan 2 Door Roof Transport System User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Roof Transport System for Your Porsche Taycan 2 Door Second Generation (2025-2026)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Roof Transport System
214
Roof Transport System
Transporting objects on the roof.
WARNING
Unsecured or incorrectly
secured roof transport
system or individual
load-carrying devices
An unsecured or incorrectly secured roof transport
system can become detached from the vehicle while
driving and cause serious accidents.
e Install individual load-carrying attachments such
as a ski/snowboard holder or roof box as cen-
trally as possible with respect to the supports.
e Check the roof transport system and load-carry-
ing devices before every trip and at regular in-
tervals during longer trips to ensure that they are
fitted correctly and securely.
e Tighten all fastening screws again.
WARNING
Changed vehicle
handling
The handling of the vehicle changes when the roof
transport system is fitted and loaded.
e Adapt your driving style accordingly.
e Do not drive at a speed of more than
130 km/h (81 mph) when the roof transport
system is loaded.
e When the roof transport system is fitted but not
loaded, do not drive at a speed of more than
180 km/h (110 mph).
WARNING
Unsecured or incorrectly
secured load
An unsecured or incorrectly secured load can be-
come detached from the roof transport system while
driving and cause serious accidents.
e Secure the load so that it will not move during
the journey.
e Load the roof transport system so that the load
does not protrude over the sides of the roof
transport system. Never load the roof transport
system wider than the width of the vehicle.
e Do not use elastic rubber tensioners.
e Position the centre of gravity of the load as low
as possible with respect to the roof transport
system and distribute the load evenly over the
load area.
NOTICE
Washing the vehicle in a car wash or failure to ob-
serve the overall vehicle height or the maximum
permitted gross weight can damage the vehicle or
roof transport system.
e Remove the complete roof transport system be-
fore washing the vehicle in a car wash.
e Check the overall vehicle height with the roof
transport system fitted before driving through
height-restricted entrances (e.g multi-storey car
parks).
e Do not exceed the maximum roof load, maximum
vehicle weight and maximum axle loads.
Information
e If you are not using the roof transport system,
remove it completely from the vehicle in order to
optimise power consumption and reduce noise.
Various objects can be transported safely and se-
curely using the roof transport system and attach-
ments, e.g. ski/snowboard holder, roof box or bicycle
rack.
e Only use roof transport systems that have been
tested and approved by Porsche. Conventional
roof rack systems cannot be mounted on the
vehicle.
For more information on the roof transport system:
e Contact your Porsche partner.
Fitting the roof transport system
bb Vehicles with a panoramic solid glass roof.
Fig. 160: Components of the roof transport system
A Front carrier bar (long)
B Rear carrier bar (short)
C Cover trims
D Torque wrench
E key
F Assembly protection
G Adapter
When fitting for the first time:
e Adjust the front and rear carriers to fit the width
of the vehicle.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Roof Transport System
215
NOTICE
Risk of damage to paintwork and/or glass from the
carrier foot.
e Secure the assembly protection to the carrier
foot while assembling the carrier.
Fig. 161: Open the flaps of the roof trim
1. Open the flaps J of the roof trim.
Fig. 162: Locking and folding up the cover flaps
2. Unlock cover flap H with the key E and fold up.
Fig. 163: Loosen adjusting screws.
3. Initial assembly:
a. Place adapter G on torque wrench D. Loosen
adjusting screws I on the two upper sides of
the respective carrier using torque wrench D.
Fig. 164: Affix assembly protection
b. Secure assembly protection F to the carrier
foot on the opposite side.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Roof Transport System
216
Fig. 165: Placing the carrier on the roof
c. Place long carrier A at the front and short
carrier B at the rear in the holders on the ve-
hicle K and, at the same time, adapt to the
vehicle width by means of the adjustable
carrier feet.
Ensure that the carriers are fitted in accord-
ance with the stickers on the underside of the
carriers.
Fig. 166: Tighten fastening screws.
d. Screw in all 4 fastening screws on the car-
riers using torque wrench D until flush with
the surface, but do not yet tighten fully.
Fig. 167: Tighten adjusting screws.
e. Tighten the adjusting screws on the tops of
the carriers on both sides slightly, but do not
yet tighten them fully. Then tighten the ad-
justing screws on the top to a torque of 8 Nm
using torque wrench D. In order to do this,
turn torque wrench D until you hear a "crack".
Continue with Assembly Step 4.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Roof Transport System
217
Fig. 168: Affix assembly protection
3. Further assembly:
a. Secure assembly protection F to the carrier
foot on the opposite side.
Fig. 169: Placing the carrier on the roof
b. Place long carrier A at the front and short
carrier B at the rear in the holders on the ve-
hicle K located in the recesses on the trims.
Fig. 170: Tighten fastening screws.
4. Screw in all 4 fastening screws on the carriers
using torque wrench D until flush with the sur-
face. Then tighten all fastening screws to a tor-
que of 8 Nm. In order to do this, turn torque
wrench D until you hear a "crack".
e Check carriers to ensure they are sitting correctly
and securely on the vehicle
Fig. 171: Fold down the cover flaps and lock
5. Fold cover flaps H of the carriers fully downwards
and mount the desired load-carrying device (e.g.
for roof box, bicycle rack) on the carrier. Then
close the cover flaps and lock using key E.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Roof Transport System
218
Fig. 172: Cutting the profile trims to size and attaching
6. Cut profile trims C to size and push them side-
ways into the carriers or press them into the
carriers from above to protect against moisture
and dirt and also to prevent wind noise.
Information
After driving 50 km (30 mls), retighten all screws on
the carriers and load-carrying devices.
Fitting mounting components
Fig. 173: Fitting mounting components
1. Unlock cover flaps with the key and fold back.
2. Insert the mounting components into the T
groove provided.
3. Close the cover flaps and lock them with the key.
4. Always read the relevant installation instructions
for fitting and securing mounting components.
Closing the profile trim
For protection against moisture and dirt and to pre-
vent wind noise, the T-groove of the profile trim
should be closed when the fasteners are not in use.
Fig. 174: Cutting the profile trims to size and attaching
1. Cut the profile trim to the length of the basic
carrier.
2. Press the profile trim into the T-groove.

Related Topics

Popular Owner Manuals