Get Do-it-yourself -> Fuses and light bulbs Guide for Skoda Citigo SUV First Generation (2011-2020)

Fuses in the dashboard

Fuses and light bulbs

Fuses

Fig. 167

Remove the fuse box cover.

 Introduction

Fig. 166

Blown fuse

 Read and observe and on page 134 first.

The fuses are located underneath the steering wheel on the underside of the

dash panel » Fig. 167.

Individual electrical circuits are protected by fuses. A blown fuse is recognisa-

ble from the melted-through metal strip » Fig. 166.

Replacing fuses

Remove the ignition key, turn off the lights and all electrical consumers.

Press securing tab

›

A

» Fig. 167.

›

WARNING

Push the lid in the direction of the arrow.

Always read and observe the warnings before completing any work in the

engine compartment » page 112.

B

Remove bracket

.

Use the clip to pull the fuse out, then insert a new fuse.

Replace the bracket at the original position.

Close the cover in the opposite direction to the arrow until it clicks into

place.

CAUTION

■

Replace the faulty fuse with a new one of the same amperage.

If a newly inserted fuse again blows after a short time, then seek assistance

■

from a specialist garage.

■

“Do not repair” the fuses and do not replace them with stronger fuses - dan-

ger of fire and damage to another electrical system.

Note

■

We recommend always carrying replacement fuses in the vehicle.

There can be several power consuming devices for one fuse. Multiple fuses

■

may exist for a single power consuming device.

134

Do-it-yourself

No.

Consumer

Fuse assignment in the dashboard

Vehicle with START-STOPsystem: Radio

Vehicle without START-STOPsystem: Button lighting, light switch, li-

cense plate light

15

Fig. 168

Fuses

16

17

Vehicle lighting - Rear fog light

Rear window wiper

Panoramic roof

18

19

20

21

22

Central locking system

Rear window heating

Reversing lights, fog lights

Horn

Voltage stabiliser (for the START-STOP system), vehicle lighting (ve-

hicle without START-STOP system)

23

 Read and observe and on page 134 first.

24

25

Headlamp flasher

Windscreen wipers

No.

Consumer

Vehicle with START-STOPsystem: Vehicle lighting

Vehicle without START-STOPsystem: Radio

1

Air Conditioning, diagnostic connector

26

Operating the headlight range control, parking aid, positional adjust-

ment of the electric door mirrors, seat heating

2

3

27

28

29

Indicator light, brake light, daytime running light

Selector lever for the automatic transmission

Fuel pump

Automatic transmission, engine control unit, power steering, control

lever under the steering wheel, instrument cluster, radiator fan

Engine control unit, instrument cluster, control lever under the

steering wheel, fuel pump

4

5

Airbag

30

Reversing light

31

32

33

34

Vehicle lighting

6

Front and rear windscreen wiper system

Main beam headlamp - left side

Main beam headlamp - right side

Not assigned

Central control system

Vehicle lighting - parking light

Interior lighting

7

8

9

Vehicle lighting - right side (applies to vehicle without START-STOP

system), instrument cluster

10

11

12

13

14

Electric exterior mirror heater, diagnostic port, rain sensor

Daytime driving light

35

Vehicle lighting - left side (applies to vehicle without START-STOP

system)

36

37

38

Not assigned

Vehicle lighting - left side

Vehicle lighting - right side

ESP

Bar with buttons, DC-DC voltage converter (applies to vehicle with

START-STOP system), engine start



135

Fuses and light bulbs

Position the cover against the arrow until it clicks.

›

No.

Consumer

Control lever under the steering wheel, front and rear window wash-

er

39

Fuse arrangement in the engine compartment

Lambda probe, radiator fan, gas valve, oil pressure valve, valve for ac-

tivated charcoal filter, engine components

40

Fig. 170

Fuses

41

42

43

44

45

46

47

48

49

50

51

Brake pedal switch, clutch pedal switch, engine components

Engine control system

Vacuum pump for brake system, air conditioning

Injection valves, engine components, fuel pump

Ignition coils, engine components

12-Volt power socket

 Read and observe and on page 134 first.

Air blower for air conditioning/heating

Seat heaters

No.

1

Consumer

Electric power windows

ABS/ESP

Vehicle lighting - daytime running lights, high beam

Electric power windows

2

Radiator fan, blower fan for air conditioning

Cooling control system, ignition

ABS/ESP

3

4

Fuses in the engine compartment

5

Battery data module, ignition lock

Ignition lock, starter

Fig. 169

Remove the fuse box cover.

6

Bulbs

 Introduction

We recommend having bulbs replaced by a specialist garage or seeking other

expert help in the event of any uncertainties.

▶

Switch off the ignition and all of the lights before replacing a bulb.

Faulty bulbs must only be replaced with the same type of bulbs. The designa-

tion is located on the light socket or the glass bulb.

 Read and observe and on page 134 first.

▶

The fuses are located underneath a cover next to the vehicle battery » Fig. 169.

We recommend having the headlight settings checked by a specialist garage

after replacing a bulb in the low or high beam unit or the fog lamp.

Replacing fuses

Remove the ignition key, turn off the lights and all electrical consumers.

Press the locking keys

›

1

of the cover » Fig. 169 together simultaneously.

›



Visit a specialist garage if an LED diode is faulty.

2

Push the cover in the direction of the arrow

Replace the defective fuse.

.

136

Do-it-yourself

 Read and observe and on page 137 first.

Bulb arrangement » Fig. 171

WARNING

■

Always read and observe the warnings before completing any work in the

engine compartment » page 112.

Accidents can be caused if the road in front of the vehicle is not suffi-

ciently illuminated and the vehicle cannot or can only be seen with difficulty

by other road users.

Bulbs H4, H7 and H8 are pressurised and may burst when changed - there

is a risk of injury! We therefore recommended wearing gloves and safety

glasses when changing a bulb.

A

B

C

D

E

Flashing

■

Low beam and high beam

Daytime running and parking light

Low beam

■

High beam

Removing bulbs for low and high beam- Variant 1

CAUTION

Do not take hold of the glass bulb with naked fingers (even the smallest

amount of dirt reduces the working life of the light bulb). Use a clean cloth,

napkin, or similar.

Note

■

This Owner's Manual only describes the replacement of bulbs where it is

possible to replace the bulbs on your own without any complications arising.

Other bulbs must be replaced by a specialist garage.

■

We recommend that a box of replacement bulbs always be carried in the ve-

hicle.

Fig. 172 Removing bulbs for low and main beam

 Read and observe and on page 137 first.

Bulb arrangement in the front headlights

1

Remove the connector from the bulb in the direction of arrow

» Fig. 172 .

›

A

Remove the protective cap

.

›

Press the safety catch in the direction of the headlamp and then unhook in

2

the direction of arrow

» Fig. 172 .

3

Open out the safety catch in the direction of arrow

.

›

4

Remove the light bulb in the direction of arrow

and insert a new light bulb

in such a way that the fixing lugs of the light bulb socket fit into the recesses

of the lamp.

Insertion of the bulb takes place in reverse order.

Fig. 171 Headlights: Version 1/version 2

137

Fuses and light bulbs

Change the bulb and insert the connector with the new bulb into the head-

›

Replacing the bulb for daytime running lights and parking lights-

Variant 1

2

light in the opposite direction to the arrow

.

Turn the connector with the new bulb in the opposite direction to the arrow

1

until it stops.

Use the protective caps

Fig. 173

D

E

and » Fig. 171 on page 137.

Replacing the bulb for daytime

running lights and parking lights

Changing the bulb for the front turn signal light

 Read and observe and on page 137 first.

C

Turn the housing containing the bulb

» Fig. 171 on page 137 as far as the

» Fig. 173 .

›

1

stop in the direction of the arrow

2

Remove the housing containing the bulb in the direction of arrow

Change the bulb.

.

›

Fig. 175 Changing the bulb for the front turn signal light. Version 1/ver-

sion 2

Insert the housing containing the light bulb in the lamp housing in the oppo-

2

site direction to arrow

.

 Read and observe and on page 137 first.

1

Screw the housing in the opposite direction to arrow

place.

until it clicks into

›

1

Turn the socket with the bulb to the stop in the direction of the arrow

» Fig. 175.

›

Change bulb for low beam and high beam - Variant 2

2

Remove the housing containing the bulb in the direction of arrow

Unscrew the defective bulb in its housing in an anti-clockwise direction and

remove it.

.

›

Fig. 174

Removing bulbs for high and

Place a new bulb in the housing and turn it in a clockwise direction as far as it

will go.

Insert the housing containing the light bulb in the lamp housing in the oppo-

›

main beam

2

site direction to arrow

.

1

Screw the housing in the opposite direction to arrow

place.

until it clicks into

 Read and observe and on page 137 first.

D

E

Remove the protective caps

and

» Fig. 171 on page 137.

›

1

Turn the holder with the bulb in the direction of arrow

Remove the holder with the bulb in the direction of arrow

» Fig. 174.

2

.

138

Do-it-yourself

8

Remove the socket with the bulb in the direction of arrow

.

›

Changing light bulbs for fog lights

Place a new connector with the bulb in the headlamp and turn it in the direc-

7

tion of arrow

as far as the stop.

Attach the connector until it clicks firmly into place.

›

Insert wheel arch cover

Fold the wheel house trim back.

Push in the part of the expansion rivet with a slit

one turn in the opposite direction to arrow

Firmly tighten the two attachment bolts

›

2

and turn it a quarter of

» Fig. 176.

with the screwdriver.

›

1

A

›

Changing the bulb for the licence plate light

Fig. 176 Remove wheel arch trim

Fig. 178 Remove licence plate light

Fig. 177 Changing a bulb

 Read and observe and on page 137 first.

A

Insert a slotted screwdriver into the slot in area

» Fig. 178 and free up the

›

 Read and observe and on page 137 first.

1

lamp in the direction of arrow

.

Remove wheel arch trim

Remove the lamp from the bumper.

Unscrew the lamp in the direction of arrow

›

A

Use the on board tool to remove screws

Using a flat, blunt object (e.g. a coin) turn the part of the expansion rivet with

a slit a quarter of a turn in the direction of arrow

» Fig. 176 from the wheel well.

2

and remove it in the direction

›

3

of arrow

.

›

1

.

Change the bulb.

›

Pull out the part of the expansion rivet with a slit in the direction of arrow

Insert the housing with the bulb in the lamp and turn it in the opposite direc-

›

2

.

2

tion to arrow

as far as the stop.

3

Take out the expansion rivet in the direction of the arrow

.

Insert the lamp in the left side of the hole and press gently until the spring

snaps into place.

›

Changing a bulb

4

Open out the wheel house trim in the direction of arrow

» Fig. 177 .

›

CAUTION

5

Press the latch on the connector in the direction of arrow

.

›

Ensure that the vehicle paintwork and the tail lamp are not damaged when re-

moving and installing the licence plate lamp.

6

Remove the connector in the direction of the arrow

.

7

Turn the socket with the bulb to the stop in the direction of the arrow

.

139

Fuses and light bulbs

Removing/installing taillights

Replacing the bulbs in the tail lamp assembly

Fig. 179 Remove light / pull out connector

 Read and observe and on page 137 first.

Removing

Fig. 180 Inner part of the lamp

 Read and observe and on page 137 first.

Changing a bulb

A

1

Open up the flap in area

in the direction of arrow

Insert the screwdriver under the bottom edge of the locking mechanism

and pull out the locking mechanism on the connector in the direction of ar-

» Fig. 179 .

Press down on the lamp holder » Fig. 180 -  and remove the holder from

the lamp.

›

B

›

Turn the light bulb counter-clockwise to the stop and remove it from the

bulb holder» Fig. 180 - .

›

2

row

.

C

3

Press the catch

in the direction of arrow

.

Insert a new bulb into the holder and turn in a clockwise direction to the

stop.

Insert the bulb holder in the light.

›

4

.

Pull out the connector in the direction of the arrow

Hold the lamp firmly and unscrew the plastic nut

Remove the lamp carefully from the body.

.

D

›

The lamp holder must engage firmly.

Fitting

Insert the bulb holder in the light.

Carefully place the tail light assembly in the opening in the body and hold

firmly.

›

D

Screw in and tighten the plastic nut

» Fig. 179 .

›

B

Push the connector into the bulb holder and press down on the catch

in

2

the opposite direction to arrow

.

1

Fold back the cover in the opposite direction to arrow

.

›

CAUTION

Ensure that the vehicle paintwork and the tail lamp are not damaged when re-

moving and installing the taillight.

140

Do-it-yourself

Do-it-yourself -> Fuses and light bulbs for Your Skoda Citigo SUV First Generation (2011-2020)

Related Topics

Popular Owner Manuals

Latest Owner Manuals