Get Do-it-yourself -> Fuses and light bulbs Guide for Skoda Fabia 4 Door Seecond Generation (2007-2013)

Note

Fuses and light bulbs

■

We recommend that you always carry replacement fuses in the vehicle. A box

of replacement fuses can be purchased from ŠKODA Original Accessories.

Fuses

■

One fuse may cover several consumers.

■

A single consumer may use several fuses.

 Introduction

This chapter contains information on the following subjects:

Fuses in the dash panel

Fuses in the engine compartment

168

170

Fig. 150

Underside of the dash panel: Dis-

tribution board cover.

Individual electrical circuits are protected by fuses.

Before replacing a fuse, switch off the ignition and the appropriate consumer

Find out which fuse belongs to the component that is not operat-

ing » page 168, Fuses in the dash panel or » page 170, Fuses in the engine

compartment.

›

Take the plastic clip out of its fixture in the cover of the fuse box, place it on

the relevant fuse and pull it out.

›

Fuse colour

light brown

dark brown

red

Maximum amperage

5

7.5

10

15

blue

yellow

20

25

30

white

green

Fig. 151 Schematic representation of the fuse box for vehicles with left-

hand steering/right-hand steering

WARNING

Always read and observe the warnings before completing any work in the

engine compartment » page 138.

 Read and observe and on page 168 first.

CAUTION

The fuses are located on the left side of the dash panel behind a cover.

■

“Never repair” fuses or replace them with a fuse of a higher amperage –

there is a risk of fire. This may also cause damage at another part of the elec-

trical system.

Have the electrical system checked as quickly as possible by a specialist ga-

rage if a newly inserted fuse blows again after a short time.

Carefully remove the cover in the direction of the arrow » Fig. 150.

After the fuse has been replaced, replace the cover in the dash panel in the

›

opposite direction of the arrow so that the guide lugs are guided into the

openings of the dash panel. Close the cover until it clicks into place.

■



■

A blown fuses is recognisable by the molten metal strip. Replace the faulty

fuse with a new one of the same amperage.

168

Do-it-yourself

Fuse assignment in the dash panel

No. Power consumer

27

28

29

30

31

Telephone preinstallation

1

S-contact

Petrol engine: AKF valve, Diesel engine: Control flap

Injection, coolant pump

2

3

4

5

6

7

START-STOP, air-conditioning system

Instrument cluster, headlamp beam adjustment

Control unit for ABS, button for START STOP

Petrol engine: Speed regulating system

Reversing light (manual gearbox)

Fuel pump, ignition, Cruise control system, operation of PTC relay

Lambda probe

32

33

34

35

36

37

38

39

High pressure fuel pump, pressure valve

Engine control unit

Ignition, engine control unit, automatic gearbox

Brake pedal switch, clutch pedal switch

Engine control unit, vacuum pump

Daytime running lights/radio for vehicles with START-STOP

Main beam

8

Operating controls for the heating, control unit for air conditioning

system, parking aid, control unit for cornering lights, radiator fan,

washing nozzles

9

Rear fog light, DC/DC converter START-STOP

Fog lights

10

11

Windscreen Wiper and Washer System

Mirror adjustment

Air blower for heating

40-41 Not assigned

12

13

14

15

16

17

18

19

20

21

Control unit for trailer detection

Control unit for automatic gearbox

Motor for halogen projector headlights with cornering light function

PDA navigation system

42

43

44

45

46

47

48

49

50

51

Rear window heater

Horn

Windscreen wipers

Central control unit for convenience system

Engine control unit, fuel pump

Electro-hydraulic power steering

Light switch power supply

Cigarette lighter, power socket in the luggage compartment

ABS, START-STOP (DC/DC) converter ESP

Turn signal lights, brake lights

Mirror heater

S-contact

Alarm

START-STOP (DC/DC) transformer, radio

Electrical power window (front and rear) - left side

Electrical power window (front and rear) - right side

Parking light = left side, electrical sliding/tilting roof

START-STOP (instrument cluster), alarm

Control unit for automatic gearbox

Reversing light, fog lights with the function CORNER

Operating controls for the heating, control unit for air conditioning

system, parking aid, mobile phone, instrument cluster, steering an-

gle sender, ESC, vehicle voltage control unit, multifunction steering

wheel

52

53

54

55

56

57

58

22

Interior lighting, storage compartment and luggage compartment,

side lights

23

Headlight cleaning system, parking light - right side

Left low beam, headlight range adjustment

Low beam on the right

24

25

26

Central control unit

Seat heaters

Rear window wiper

169

Fuses and light bulbs

No. Power consumer

Fuses in the engine compartment

6

7

Glow plugs, radiator fan

Electro-hydraulic power steering

ABS or TCS or ESC

8

9

Radiator fan

10 Automatic gearbox

11 ABS or TCS or ESC

12 Central control unit

13 Electrical auxiliary heating system

Note

Fig. 152 Vehicle battery: Distribution board cover.

Fuses 1-7 are replaced by a specialist garage.

Fig. 153

Bulbs

Schematic representation of fuse

box in engine compartment

 Introduction

This chapter contains information on the following subjects:

Headlights

171

Changing the low beam and high beam bulb (halogen headlights)

Changing the low beam and high beam bulb (halogen projector

headlights)

Changing the high beam bulb (halogen projector headlights)

Changing the front turn signal bulb

Changing the front parking light bulb

Foglights and daytime running lights

Fabia Scout, Fabia RS foglights

172

173

174

 Read and observe and on page 168 first.

Press the securing clips on the fuse box cover together at the same time in

the direction of arrow A » Fig. 152 and remove the cover in the direction of

arrow B .

Release the fixtures in the openings C using a flat screwdriver and fold the

cover upwards in direction of arrow D .

›

Changing the licence plate light bulb

Rear light

Fuse assignment in engine compartment

No. Power consumer

Some manual skills are required to change a bulb. For this reason, if uncertain,

we recommend that bulbs are replaced by a specialist garage or other expert

help is sought.

1

Generator

2

3

4

5

Not assigned

Switch off the ignition and all of the lights before replacing a bulb.

Faulty bulbs must only be replaced with the same type of bulbs. The designa-

tion is located on the light socket or the glass bulb.

›

Interior

›

Electrical auxiliary heating system

Interior

A stowage compartment for replacement bulbs is located in a plastic box in

the spare wheel or underneath the floor covering in the boot.

›



170

Do-it-yourself

WARNING

Headlights

■

Always read and observe the warnings before completing any work in the

engine compartment » page 138.

■

Accidents can be caused if the road in front of the vehicle is not suffi-

ciently illuminated and the vehicle cannot or can only be seen with difficul-

ty by other road users.

■

Bulbs H7 and H4 are pressurised and may burst when changed - there is a

risk of injury. We therefore recommended wearing gloves and safety

glasses when changing a bulb.

■

Switch off the respective vehicle light when changing the bulb.

CAUTION

Fig. 154 Bulb arrangement: Halogen headlights/halogen projector head-

lights

■

Do not take hold of the glass bulb with naked fingers (even the smallest

amount of dirt reduces the working life of the light bulb). Use a clean cloth,

napkin, or similar.

 Read and observe and on page 171 first.

■

When removing and installing the number plate light and tail light make sure

that the paintwork of the vehicle and the tail light are not damaged.

Bulb arrangement in the Halogen headlamp

A - low beam, main beam and side lights

Note

■

B - front turn signal light

This Owner's Manual only describes the replacement of bulbs where it is pos-

sible to replace the bulbs on your own without any complications arising. Other

light bulbs should be changed by your specialist garage.

We recommend that you always carry a box of replacement bulbs in the vehi-

Bulb arrangement in the Halogen projector headlights

1

- low beam / low and main beam

■

2 - Parking light / parking and main beam lights

3 - turn signal lights

cle. Replacement bulbs can be purchased from ŠKODAOriginal Accessories.

We recommend having the headlight settings checked by a specialist garage

after replacing a bulb in the main beam, low beam or fog lights.

■

Visit a specialist garage if an LED is faulty.

Changing the low beam and high beam bulb (halogen headlights)

Fig. 155

Removing bulbs for low and

main beam

 Read and observe and on page 171 first.



Remove the rubber cover A » Fig. 154 on page 171.

›

171

Fuses and light bulbs

Remove the connector from the bulb, unlock the securing clip and remove

the bulb » Fig. 155.

Insert a new light bulb in such a way that the fixing lugs of the bulb socket fit

in the recesses of the reflector.

Lock the circlip and insert the connector in the bulb.

Fit the rubber cover A .

 Read and observe and on page 171 first.

›

Remove the rubber cover 2 » Fig. 154 on page 171.

Turn the connector with the bulb to the stop in the direction of the ar-

row » Fig. 157 and remove it.

›

Replace the bulb, insert the connector and new bulb and turn to the stop in

the opposite direction to that of the arrow.

›

Fit the rubber cover 2 .

›

Changing the low beam and high beam bulb (halogen projector

headlights)

Changing the front turn signal bulb

Fig. 156

Read and observe and on page 171 first.



Removing bulbs for low beam/

low and main beam

Remove the bulb holder B » Fig. 154 on page 171 or the bulb holder 3 to the

stop in an anti-clockwise direction and remove with the bulb for the turn sig-

nal.

Replace the bulb, insert the bulb holder with the new bulb and turn clock-

wise to the stop.

›

Changing the front parking light bulb

 Read and observe and on page 171 first.

Remove the rubber cover

1

» Fig. 154 on page 171.

›

Remove rubber cover A » Fig. 154 on page 171 or 2 .

Grasp the lamp holder and remove it from the bulb housing.

Replace the light bulb and insert the lamp holder back into the headlamp

with the bulb.

›

Turn the socket with the bulb to the stop in the direction of the ar-

row » Fig. 156 and remove it.

Replace the bulb, insert the connector and new bulb and turn to the stop in

the opposite direction to that of the arrow.

›

Fit the rubber cover.

›

Fit the rubber cover

1

.

Changing the high beam bulb (halogen projector headlights)

Fig. 157

Removing the bulb for the main

beam

172

Do-it-yourself

Foglights and daytime running lights

Fabia Scout, Fabia RS foglights

Fig. 158 Front bumper: Protective grille/removing the fog light

 Read and observe and on page 171 first.

Fig. 159 Front bumper: Fabia Scout/Fabia RS

Bulb location » Fig. 158.

A - Bulb for daylight driving light

B - Light bulb for fog lights

Removing the cap

Grasp the protective grille in the areas marked by the arrows » Fig. 158 - 

and remove the cover in the direction of the arrow.

›

Replacing light bulbs for fog lights/daytime running lights

Fig. 160 Front bumper: Fog lights/fog lights: Replacing the light bulb

Insert your hand into the opening in the protective grille and press the

›

catch » Fig. 158 -  in the direction of the arrow.

Remove the fog lamp.

Turn the connector with the bulb in counter-clockwise up to the stop and re-

move.

›

 Read and observe and on page 171 first.

›

Removing the cap and fog light

Insert the tool into the opening above the fog light » Fig. 159 -  (Fabia

Scout) » page 159, Vehicle tool kit and remove the cover.

Insert a finger into the opening next to the foglight » Fig. 159 -  (Fabia RS)

and remove the cap.

Replace the bulb, insert the holder with the new bulb and turn clockwise to

the stop.

To re-install the fog light, first of all place the fog light with the lug on the

side opposite the licence plate.

›

Unscrew » page 159, Vehicle tool kitthe screws » Fig. 160 - with the screw-

driver .

Remove the fog lamp.

Press in the fog lamp on the side closest to the licence plate.

Insert the cap, beginning with the lug on the side opposite the license plate.

Press in the cap on the side facing the license plate. The cap must engage

firmly.

›

Changing light bulbs and installing fog lights

Press the locking tab

1

» Fig. 160 on the connector A and remove the con-

›



nector from the bulb holder B .

173

Fuses and light bulbs

Turn the bulb holder B and bulb in the direction of the arrow to the stop and

remove.

Replace the bulb, insert the bulb holder and new bulb and turn in the oppo-

site direction to that of the arrow to the stop.

›

Rear light

Insert the plug A into the socket B .

Retighten the screws and insert the cap. The cap must engage firmly.

›

Changing the licence plate light bulb

Fig. 161

Boot lid: Licence plate light

Fig. 162 Plastic nut/rear lamp

Fig. 163

Tail light assembly: Bulb ar-

rangement

 Read and observe and on page 171 first.

Insert a flat screwdriver into the opening in the area of the arrow » Fig. 161

and carefully press towards the centre of the lamp; the lamp pops out slight-

ly as you do this.

›

Remove the lamp.

Remove the faulty bulb from the holder and insert a new one.

Replace the glass cover and push in until the stop.

›

 Read and observe and on page 171 first.

›

Bulb location » Fig. 163.

Make sure that you install the glass cover in the correct position.

1

- Rear fog light/Reversing light

2 - Turn signal lights

3 - Brake lights

4 - parking lights

Removing and installing the tail light

Open the tailgate.

Hold the rear light assembly still with one hand and unscrew the plastic

nut » Fig. 162 -  with the other.

›

Grip the tail lamp assembly and carefully remove it by pulling it back at an an-

gle with loosening movements. Do not pull the grommet with the cables out

of the bodywork.

›



174

Do-it-yourself

To refit the rear light assembly, first insert screw A into the opening in the

bodywork » Fig. 162.

Carefully press the tail light assembly into the bodywork so that the bolts B

latch with the mounts in the body.

Hold the rear light assembly still with one hand and attach and tighten the

nuts » Fig. 162 -  with the other hand.

›

Replacing the bulbs in the tail lamp assembly

To replace the bulb, turn the bulb holder anti-clockwise to the stop and re-

move it from the housing » Fig. 163.

›

Replace the bulb, insert the holder with the bulb into the housing and turn in

a clockwise direction to the the stop.

›

Note

For slackening and tightening the plastic nut use a coin or similar object.

175

Fuses and light bulbs

Do-it-yourself -> Fuses and light bulbs for Your Skoda Fabia 4 Door Seecond Generation (2007-2013)

Related Topics

Do-it-yourself

Popular Owner Manuals

Latest Owner Manuals