Get Breakdown assistance Guide for Skoda Superb SUV Second Generation (2009-2015)

216 Breakdown assistance

Breakdown assistance

First-aid box

Warning triangle

Fig. 183 Placing of the warning triangle

Fig. 182 Compartment for stowing first-aid box/compartment for stowing first-aid box (Com-

bi)

The warning triangle can be attached to the trim panel of the rear wall with rub-

ber straps ⇒ꢀfig. 183.

First-aid box

Note

The compartment for stowing the first-aid box is located in the right of the lug-

gage compartment ⇒ꢀfig. 182.

If you also want to equip your vehicle with a warning triangle, we recommend a

warning triangle from the range of ŠKODA Original Accessories that you can pur-

chase from authorised ŠKODA Service Partners.



Note

●

Pay attention to the use-by-date of the contents of the first-aid box.

We recommend a first-aid box from the range of ŠKODA Original Accessories

Fire extinguisher



that you can purchase from an authorised ŠKODA Service Partner.

The fire extinguisher is attached with straps in a holder under the driver seat.

Please read carefully the instructions which are attached to the fire extinguish-

er.

The fire extinguisher must be checked by an authorised person or company annu-

ally (please observe the differing legal requirements).

£

Breakdown assistance 217

●

Replacement lamp,

Torx wrench.

WARNING

If the fire extinguisher is not correctly attached, in case of sudden manoeu-

vres or an accident it can be “thrown” through the interior compartment and

cause injuries.

Before placing the lifting jack back in its storage area, screw in the arm of the lift-

ing jack fully.

WARNING

Note

●

The fire extinguisher must comply with the relevant and valid legal require-

ments.

Pay attention to the expiration date of the fire extinguisher. If the fire extin-

guisher is used after the expiration date, its proper function is no longer assured.

The fire extinguisher is only supplied in certain countries within the scope of

●

The factory-supplied lifting jack is only intended for your model of vehicle.

On no account attempt to lift a heavier vehicle or other loads - risk of injury!

Ensure that the vehicle tool kit is safely attached in the luggage compart-

ment.

●



Note

delivery.



Ensure that the box is always secured with the strap.

Vehicle tool kit

Spare wheel

Fig. 184 Luggage compartment: Storage

compartment for vehicle too kit

Fig. 185 Luggage compartment: Spare

wheel

The vehicle tool kit and the lifting jack with sticker are housed in a plastic box in

the spare wheel ⇒ꢀfig. 184 or in the compartment for the spare wheel. There is al-

so space here for the removable ball for the trailer towing device. The box is at-

tached with a strap on the spare wheel.

The spare wheel lies in a well under the floor covering of the luggage compart-

ment and is fixed in place using special screws ⇒ꢀfig. 185.

Before removing the spare wheel, you must take out the box with the vehicle tool

kit box ⇒ꢀfig. 184.

The vehicle tool kit contains the following parts (depending on equipment fitted):

●

Wire clamps for removing the full wheel trims,

Plastic clip for a wheel bolt cover,

Wheel wrench,

Towing eye,

Adapter for the wheel bolts lock,

One should check the inflation pressure in the spare wheel (at best when general-

ly checking the tyre air pressures - see sign on the fuel filler flap ⇒ꢀpage 210) to

ensure that the spare wheel is always ready to use.

Temporary spare wheel

A warning label displayed on the rim of the temporary spare wheel indicates that

your vehicle is equipped with a temporary spare wheel.

£

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

218 Breakdown assistance

Please observe the following notes when driving with a temporary spare wheel:

WARNING

●

The warning label must not be covered after installing the wheel.

Do not drive faster than 80 km/h with this spare wheel and pay particular at-

●

If you find yourself in flowing traffic switch on the hazard warning lights

system and place the warning triangle on the side of the road at the prescri-

bed distance from your vehicle. Comply with the national legal regulations. In

this way you are protecting not only yourself but also other road users.

tention while driving. Avoid accelerating at full throttle, sharp braking and fast

cornering.

●

The inflation pressure for this spare wheel is identical to the inflation pressure

●

Never start the engine with the vehicle sitting on the raised jack - danger

of suffering injury.

of the standard tyres. The temporary spare wheel R 18 must have an inflation

pressure of 420 kPa (4.2 bar)!

●

Use this spare wheel only to reach the nearest specialist garage as it is not in-

tended for continuous use.

No other summer or winter tyres must be mounted on the rim of the spare

CAUTION

If you have to change a wheel on a slope first block the opposite wheel with a

stone or similar object in order to secure the vehicle from unexpectedly rolling

away.

●



wheel R 18.

Note

Changing a wheel



Comply with the national legal regulations.

Preliminary work

Changing a wheel

The following steps should be carried out before actually changing the wheel.

Always change a wheel on a level surface as far as possible.

–

If it is necessary to change a wheel, park the vehicle as far away as possible

from the traffic flow. The place you choose should be level.

–

Take off the full wheel trim ⇒ꢀpage 219 or the caps ⇒ꢀpage 219.

In the case of light alloy wheels remove the wheel trim cap ⇒ꢀpage 220.

First of all slacken the safety wheel bolt and afterwards the other wheel bolts

⇒ꢀpage 220.

–

Have all the occupants get out. While changing a tyre, the occupants of the

vehicle should not stand on the road (instead they should remain behind a

crash barrier).

–

Jack up the vehicle until the wheel to be changed is clear of the ground

⇒ꢀpage 221.

Unscrew the wheel bolts and place them on a clean surface (cloth, paper etc.).

–

Apply the handbrake firmly.

Engage 1st gear or if your vehicle is fitted with an automatic gearbox, position

the selector lever into position P.

–

Take off the wheel.

–

If a trailer is coupled, uncouple it.

Fit on the spare wheel and tighten the wheel bolts slightly.

Lower the car.

Take the vehicle tool kit ⇒ꢀpage 217 and the spare wheel ⇒ꢀpage 217 out of

the luggage compartment.

Tighten the wheel bolts firmly, alternately and diagonally using the wheel

wrench (crosswise) and lastly the wheel safety bolt ⇒ꢀpage 220.

£

–

Mount the full wheel trim/wheel trim cap or the caps.

Breakdown assistance 219

–

Push the wheel key through the clamp, support the wheel key at the tyre and

pull off the wheel trim.

Note

●

All bolts must be clean and must turn easily.

You must never grease or oil the wheel bolts!

When fitting on unidirectional tyres, ensure that the tyres rotate in the correct

Install

–

First press the full wheel trim onto the wheel at the valve opening provided.

Then press the full wheel trim into the wheel in such a way that its entire cir-

cumference locks correctly in place.



direction ⇒ꢀpage 210.

Subsequent steps

CAUTION

●

Use the pressure of your hand, do not knock on the full wheel trim! Heavy

After changing the wheel, you must perform the following steps.

knocks mainly on the points where the full wheel trim has not been inserted into

the wheel, can result in damage to the guide and centering elements of the full

wheel trim.

–

Stow and attach the replaced wheel in the spare wheel well using a special

screw ⇒ꢀfig. 185.

–

Stow the vehicle tool kit in the space provided.

●

Check for yourself that the safety wheel bolt is located in the hole in the area

of the valve before fitting the full wheel trim onto a steel wheel which is attached

with a safety wheel bolt ⇒ꢀpage 221, Securing wheels against being stolen.

Check the tyre pressure on the spare wheel just mounted as soon as possible.



Have the tightening torque of the wheel bolts checked with a torque wrench

as soon as possible. Steel and light alloy wheels must be tightened to a tight-

ening torque of 120 Nm.

Wheel bolts with caps

–

Change the damaged wheel or consult a specialist garage about possibilities

for getting repairs done.

WARNING

It is necessary to observe the guidelines given on ⇒ꢀpage 212 if the vehicle is

subsequently fitted with tyres which are different to those it was fitted with

at the works.

Note

Fig. 186 Removing the cap.

●

If you find, when changing the wheel, that the wheel bolts are corroded and

difficult to turn, the bolts must be replaced before checking the tightening torque.

Pulling off

●

Drive cautiously and only at a moderate speed to a workshop where the tight-

–

Push the plastic clip sufficiently far onto the cap until the inner catches of the



ening torque can be checked.

clip are positioned at the collar of the cap and detach the cap ⇒ꢀfig. 186.

Install

Full wheel trim

–

Push the caps fully onto the wheel bolts.

Pulling off



The caps are located in the well of the luggage compartment.

–

Hook the clamp found in the vehicle tool kit into the reinforced edge of the full

wheel trim.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

220 Breakdown assistance

Wheel trim caps

Tightening wheel bolts

1)

–

Insert the wheel wrench fully onto the wheel bolt

.

–

Grasp the end of the wrench and turn the bolt to the right until it is tight.

WARNING

Slacken the wheel bolts only a little (about one turn) as long as the vehicle has

not yet been jacked up - risk of an accident!.

Note

Fig. 187 Pulling off wheel trim cap on

light alloy wheels

Apply pressure carefully with your foot to the end of the wrench if it proves diffi-

cult to slacken the bolts. Hold tight on the vehicle when doing this and ensure

that you have a steady position.



Pulling off



–

Carefully remove the wheel trim cap using the wire clamp ⇒ꢀfig. 187.

Slackening and tightening wheel bolts

Slacken the wheel bolts before jacking up the vehicle.

Fig. 188 Changing a wheel: Slackening

wheel bolts

Slackening wheel bolts

1)

–

Insert the wheel wrench fully onto the wheel bolt

.

–

Grasp the end of the wrench and turn the bolt about one turn to the left

⇒ꢀfig. 188.

1)

Use the appropriate adapter for slackening and tightening the safety wheel bolts ⇒ꢀpage 221.

Breakdown assistance 221

Raise vehicle

WARNING

You have to raise the vehicle with a lifting jack in order to be able

to take off the wheel.

●

Always raise the vehicle with the doors closed - risk of injury.

Never position any body parts such as arms or legs under the vehicle, while

the vehicle is raised with a lifting jack.

●

Secure the base plate of the lifting jack with suitable means to prevent

possible moving. A soft and slippery ground under the base plate may move

the lifting jack, causing the vehicle to fall down. It is therefore always neces-

sary to place the lifting jack on a solid surface or use a wide and stable base.

Use a non-slip base (e.g. a rubber foot mat) if the surface is smooth, such as

cobbled stones, a tiled floor, etc.

●

Attach the lifting jack only at the attachment points provided for this pur-

pose.



Fig. 189 Changing a wheel: Jacking

points for positioning lifting jack

Securing wheels against being stolen

You need a special adapter for slackening the safety wheel bolts.

Fig. 190 Attach lifting jack

Fig. 191 Illustration image: Safety wheel

bolt with adapter

Position the lifting jack by selecting the jacking point which is closest to the wheel

to be removed ⇒ꢀfig. 189. The jacking point is located directly below the engraving

in the lower sill.

–

Pull off the full wheel trim/cap from the wheel hub or cap from the safety

wheel bolt.

–

Position the lifting jack below the jacking point and move it up until its claw is

positioned directly below the vertical web of the lower sill.

B

A

Insert the adapter

safety wheel bolt

with its toothed side fully into the inner toothing of the

right down in such a way that only the outer hexagon is

Align the lifting jack so that its claw grasps the web ⇒ꢀfig. 190 at the right be-

jutting out ⇒ꢀfig. 191.

low the embossing in the side surface of the base plate.

B

–

Insert the wheel wrench fully onto the adapter

.

Make sure that the base plate of the lifting jack rests with its entire surface on

level ground and is located vertical to the point ⇒ꢀfig. 190 where the claw

grasps the web.

Slacken the wheel bolt, or tighten it firmly ⇒ꢀpage 220.

Reinstall the full wheel trim/wheel cap after removing the adapter or place the

cap onto the safety wheel bolt.

£

–

Turn the lifting jack up further until the wheel is just clear of the ground.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

222 Breakdown assistance

–

Have the tightening torque checked with a torque wrench as soon as possi-

ble. Steel and light alloy wheels must be tightened to a tightening torque of

120 Nm.

●

with tears or punctures greater than 4 mm in size,

to repair damage to the tyre wall,

when driving with very low tyre pressure or with a completely flat tyre,

if the use-by-date (see inflation bottle) has passed.

The safety wheel bolts on vehicles fitted with them (one safety wheel bolt per

wheel) can only be loosened or tighten up by using the adapter provided.

WARNING

It is meaningful to note the code number hammered into the rear side of the

adapter or the rear side of the safety wheel bolts. You can obtain a replacement

adapter from an authorised ŠKODA Service Partner, if necessary, by quoting this

number.

●

If you find yourself in flowing traffic switch on the hazard warning lights

system and place the warning triangle on the side of the road at the prescri-

bed distance from your vehicle. Comply with the national legal regulations. In

this way you are protecting not only yourself but also other road users.

We recommend that you always carry the adapter for the wheel bolts with you in

the vehicle. It should be stowed in the vehicle tool kit.

●

Park the vehicle as far away as possible from the traffic flow. Park on as

flat and firm a surface as possible.

A tyre filled with sealant has the same driving characteristics as a standard

tyre.

CAUTION

●

Damage can occur to the adapter and safety wheel bolt if the safety wheel bolt is

tightened up too much.

●

Do not drive faster than 80 km/h, 50 mph.

Avoid accelerating at full throttle, sharp braking and fast cornering.

Check the tyre inflation pressure after driving 10 minutes.

Note

The set of safety wheel bolts can be obtained from an authorised ŠKODA Service

Partner.



Sealant is hazardous to heath. Remove immediately if it comes into con-

tact with the skin.

For the sake of the environment

Used sealant or sealant whose expiry date has passed must be disposed of in ac-

cordance with environmental protection regulations.

Tyre repair kit

General information

Note

The tyre repair kit is located in a box under the carpet in the luggage compart-

ment.

●

Observe the manufacturer's usage instructions for the tyre repair kit.

You can purchase a new bottle of sealant from the range of the ŠKODA Origi-

nal Accessories.

Use the tyre repair kit to reliably repair tyre damage caused by foreign bodies or a

puncture with diameters up to 4 mm. Do not remove foreign bodies, e.g. screws or

nails, from the tyre!

●

Change the wheel that was repaired using the tyre repair kit or consult a spe-

cialist garage about possibilities for getting repairs done.



The repair can be undertaken on the vehicle immediately.

The repair with the tyre repair kit is not at all intended to replace a permanent

repair on the tyre, this repair only serves to reach the next specialist garage.

Do not use the tyre repair kit:

●

to repair wheel damage,

in outside temperatures of less than -20 °C (-4 °F),

Breakdown assistance 223

–

Have all the occupants get out. While changing a tyre, the occupants of the

vehicle should not stand on the road (instead they should remain behind a

crash barrier).

Components of the tyre repair kit

Switch off the engine and engage 1st gear or if your vehicle is fitted with an

automatic gearbox, position the selector lever into position P.

–

Apply the handbrake firmly.

Check whether you can carry out the repairs with the tyre repair kit

⇒ꢀpage 222, General information.

–

If a trailer is coupled, uncouple it.

Remove the tyre repair kit from the luggage compartment.

2

Stick the sticker

⇒ꢀfig. 192 on the dash panel in view of the driver.

Do not remove the foreign body, e.g. screw or nail, from the tyre.

Unscrew the valve cap.

Fig. 192 Components of the tyre repair kit

1

Use the valve remover

clean surface.

to remove the valve core and place it down on a

The tyre repair kit is made up of the following parts:



1

2

Valve remover

Sticker with speed designation “max. 80 km/h”/“max. 50 mph”

Inflation hose with plug

Compressor

Seal and inflate tyres

3

Sealing tyres

4

5

10

–

Forcefully shake the tyre inflator bottle

⇒ꢀfig. 192 several times.

Tyre inflation hose

6

7

Tyre inflation pressure indicator

Air release valve

3

–

Firmly screw inflation hose

onto the tyre inflator bottle in a clockwise direc-

10

tion . The film on the cap is pierced automatically.

8

9

10

11

ON and OFF switch

12 volt cable connector

Tyre inflator bottle with sealing agent

Replacement valve core

3

–

Remove the plug from the inflation hose

the tyre valve.

and plug the open end fully into

10

Hold the bottle

with the floor facing upwards and fill the whole sealing

agent in the tyre inflator bottle into the tyres.

1

The valve remover

has a slot at its lower end which fits into the valve core.

–

Remove the empty tyre inflator bottle from the valve.

Screw the valve core back into the tyre valve using the valve remover

This is the only way in which you can remove and re-install the valve core from the

tyre valve. The same also applies to the replacement valve core

1

.



11

.

Pumping up the tyres

Preparing to use the tyre repair kit

5

–

Screw the tyre inflation hose

tyre valve.

⇒ꢀfig. 192 of the air compressor firmly onto the

Before using the tyre repair kit, carry out the following preparatory work:

7

£

–

Check whether the air release valve

is closed.

–

Park the vehicle as far away as possible from the traffic flow. Park on as flat

and firm a surface as possible.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

224 Breakdown assistance

–

On vehicles fitted with a manual gearbox, move the gearshift lever into Neu-

tral.

CAUTION

Switch off the air compressor after running 8 minutes at the latest - danger of

overheating! Allow the air compressor to cool a few moments before switching it

on again.

–

Start the engine and run it in idle.

9



Plug the connector

into 12 Volt socket ⇒ꢀpage 91.

8

Switch on the air compressor with the ON and OFF switch

Allow the air compressor to run until reaching a pressure of 2.0 - 2.5 bar. Maxi-

mum run time of 8 minutes ⇒ꢀ

.

Check after driving for 10 minutes

!

Check the tyre inflation pressure after driving 10 minutes.

–

Switch off the air compressor with the ON and OFF switch.

If the tyre inflation pressure is 1.3 bar or less:

If you cannot reach an air pressure of 2.0 – 2.5 bar, unscrew the tyre inflation

–

Do not drive the vehicle! You cannot properly seal with tyre with the break-

down kit.

5

hose

from the tyre valve.

–

Drive the vehicle approx. 10 metres forwards or backwards to allow the sealing

agent to distribute in the tyre.

Contact a Škoda dealer to obtain professional assistance.

If the tyre inflation pressure is 1.3 bar or more:

5

Screw the tyre inflation hose of the air compressor

tyre valve and repeat the inflation procedure.

firmly back onto the

–

Adjust the tyre inflation pressure to the correct value (see inside of fuel filler

cap).

If you cannot reach the required tyre inflation pressure here either, this means

the tyre has sustained too much damage. You cannot seal with tyre with the

–

Continue driving carefully to the nearest specialist garage at a maximum

speed of 80 km/h (50 mph).



breakdown kit ⇒ꢀ

.

–

Switch off the air compressor with the ON and OFF switch.

5

Remove the tyre inflation hose

from the tyre valve.

Jump-starting

After reaching a tyre inflation pressure of 2.0 – 2.5 bar, drive at a maximum speed

of 80 km/h (50 mph).

Initial steps

Check the tyre inflation pressure after driving 10 minutes ⇒ꢀpage 224, Check after

driving for 10 minutes.

You can use the battery of another vehicle for jump-starting yours if the engine

does not start because the battery on your vehicle is flat. You will require jump-

start cables for this purpose.

WARNING

Both batteries must have a rated voltage of 12 V. The capacity (Ah) of the battery

supplying the power must not be significantly less than the capacity of the dis-

charged battery in your vehicle.

●

During inflation, the tyre inflation hose and air compressor may get hot-

risk of injury!

●

Do not place hot tyre inflation hoses or hot air compressors on flammable

materials - risk of fire!

Jump-start cables

Only use jump-start cables which have an adequately large cross-section and in-

sulated terminal clamps. Please pay attention to the manufacturer's instructions.

●

If you cannot inflate the tyre to at least 2.0 bar, this means the damage

sustained was too serious. The sealing agent cannot be used to seal the tyre.

Do not drive the vehicle. Get professional assistance.

Positive cable - colour coding in the majority of cases red.

Negative cable - colour coding in the majority of cases black.

£

Breakdown assistance 225

Connecting negative terminal and engine block

WARNING

3

–

Attach one end

to the negative terminal of the battery supplying the power

●

A discharged battery may already freeze at temperatures just below 0°C.

In case of frozen battery carry out no jump-starting - risk of explosion!

B

.

4

–

Attach the other end

to a solid metal part which is connected firmly to the

●

Please pay attention to the warning instructions relating to working in the

engine compartment ⇒ꢀpage 198, Working in the engine compartment.

engine block, or to the engine block itself.

Starting engine

Note

–

Start the engine of the vehicle providing current and run the engine at idling

speed.

●

There must not be any contact between the two vehicles otherwise current

may flow as soon as the negative terminals are connected.

–

Now start the engine of the vehicle with the discharged battery.

●

cle.

The discharged battery must be properly connected to the system of the vehi-

Switch off any mobile phone, pay attention to the instructions for use of the

Interrupt the attempt at starting an engine after 10 seconds if it does not start

right away and wait for about 30 seconds before repeating the attempt.

●

–

Disconnect the cables on the engine in exactly the reverse order they were

mobile phone in such a situation.

connected up.



●

We recommend you buy jump-start cables from a car battery specialist.

WARNING

Start engine

●

The non-insulated parts of the terminal clamps must never make contact

with each other. In addition, the jump-start cable connected to the positive

terminal of the battery must not come into contact with electrically conduct-

ing parts of the vehicle - risk of short circuit!

●

Do not affix the jump starting cables to the negative terminal of the dis-

charged battery. There is the risk of detonating gas seeping out the battery

being ignited by the strong spark which results from the engine being started.

●

Run the jump-start cables so that they cannot be caught by any rotating

parts in the engine compartment.

Fig. 193 Jump-starting using the battery

from another vehicle: A - flat vehicle bat-

tery, B - battery providing current

●

Do not bend over the batteries - risk of caustic burns!

The vent screws of the battery cells must be tightened firmly.

It is important to connect the jump-start cables in the correct order.

Keep any sources of ignition (naked flame, smouldering cigarettes etc.)

away from the battery - risk of an explosion!

Never jump-start the batteries which have a too low electrolyte level - risk

of explosion and caustic burns!

Connecting positive terminals

●

1

–

Attach one end

⇒ꢀfig. 193 to the positive terminal of the discharged battery



A

.

2

–

Attach the other end

to the positive terminal of the battery supplying the

B

power

.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

226 Breakdown assistance

–

Attach the negative terminal of the battery supplying the power to a solid

metal part which is connected firmly to the engine block or to the engine block

itself.

Jump-starting on vehicles with the “START-STOP” system

–

Start the engine ⇒ꢀpage 225.

After the engine start, close the protective cap of the jump-starting point.



The vehicle

General

Fig. 194 Jump-starting on vehicles with

the START-STOP system

Vehicles with manual transmission can be towed in with a tow bar or a tow rope

or with the front or rear wheels raised.

One vehicles with the “START STOP” system, the negative cable of the charger

must never be connected directly to the negative pole of the vehicle battery, but

only to the engine earth ⇒ꢀfig. 194.

Vehicles with automatic transmission can be towed in with a tow bar or a tow

rope or with the front wheels raised. If the vehicle is raised at rear, the automatic

gearbox is damaged!



Jump-starting on vehicles with jump-starting point

A tow bar is safest way of towing a vehicle and also minimizes any shocks. You

can use a tow rope only if a suitable tow bar is not available.

Refer to the following guidelines when towing:

Driver of the towing vehicle

–

Release the clutch particularly gently when starting off or depress the acceler-

ator particularly gently if your vehicle is fitted with an automatic gearbox.

–

On vehicles with manual transmission, only push down on the accelerator ped-

al once the rope is taught.

Fig. 195 Detail of the engine compart-

ment: Jump-starting point

The maximum towing speed is 50 km/h.

Driver of the towed vehicle

For vehicles with the 3.6 ltr./191 kW FSI engines, the positive terminal of the bat-

tery supplying the power can only be connected to the jump-starting point in the

engine compartment of the vehicle which must be started by means of a jump-

starting cable ⇒ꢀfig. 195!

–

Switch the ignition on so that the steering wheel is not blocked and you can

also operate the turn signal lights, the headlight flasher, the windscreen wip-

ers and windscreen washer system.

–

Take the vehicle out of gear or move the selector lever into position N if your

–

Open the protective cap of the jump-starting point in direction of arrow.

vehicle is fitted with an automatic gearbox.

–

Connect the positive terminal of the battery supplying the power with the

jump-starting point.

Note that the brake servo unit and power steering only operate if the engine is

running. You will require significantly greater physical force to depress the brake

pedal and to steer the vehicle if the engine is not running.

£

When using a tow rope, always ensure that the tow rope is always kept taught.

Breakdown assistance 227

Front towing eye

CAUTION

●

Do not tow start the engine - danger of damaging the engine. On vehicles with

The towing eye is stored in the box of the vehicle tool kit.

a catalytic converter, unburnt fuel may get into the catalytic converter where it

may ignite. This in turn may damage or destroy the catalytic converter. You can

use the battery of another vehicle as a jump-start aid ⇒ꢀpage 224, Jump-starting.

●

If the gearbox of your vehicle no longer contains any oil because of a defect,

your vehicle must only be towed in with the driven wheels raised clear of the

ground, or on a special vehicle transporter or trailer.

●

The vehicle must be transported on a special vehicle or trailer if it is not possi-

ble to tow in the vehicle in the way described or if the towing distance is greater

than 50 km.

●

To protect both vehicles when tow-starting or towing, the tow rope should be

elastic. Thus one should only use plastic fibre rope or a rope made out of a similar-

ly elastic material.

Fig. 196 Front bumper: Removing the cover/installing the towing eye

●

One should be constantly vigilant not to allow impermissibly high towing

–

Take the cover out of the front bumper ⇒ꢀfig. 196 - left.

forces or jerky loadings. There is always a risk of excessive stresses and damage

resulting at the points to which you attach the tow rope or tow bar when you at-

tempt to tow a vehicle which is not standing on a paved road.

Screw in the towing eye by hand to the left up to the stop ⇒ꢀfig. 196 - right and

tighten it as much as possible. For tightening, we recommend that you use for

example the wheel wrench, the lashing eye of another vehicle or a similar ob-

ject which you can push through the eye.

●

Attach the tow rope or the tow bar only to the towing eyes provided for this

purpose ⇒ꢀpage 227, Front towing eye and ⇒ꢀpage 228, Rear towing eye.

–

Put the cover in place after screwing out the towing eye again and press into

place. The cover must engage firmly.

Note

●

We recommend a tow rope from the range of ŠKODA Original Accessories that

you can purchase from an authorised ŠKODA Service Partner.

Towing another vehicle requires a certain amount of practice. Both drivers

should be familiar with the particular points about towing a vehicle. Unskilled driv-

ers should not attempt to tow in another vehicle or to be towed in.

CAUTION

●

The towing eye must always be screwed in fully and firmly tightened, otherwise

the towing eye can tear when towing in or tow-starting!



●

When towing, respect the national legal provisions, especially those which re-

late to the identification of the towing vehicle and the vehicle being towed.

The tow rope must not be twisted as it may in certain circumstances result in

the front towing eye being unscrewed out of your vehicle.

●



Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

228 Breakdown assistance

Rear towing eye

Fig. 197 Rear bumper: Removing the cover/installing the towing eye

–

Press onto the bottom part of the cover in the rear bumper ⇒ꢀfig. 197 - left and

take it out.

Screw in the towing eye by hand to the left up to the stop ⇒ꢀfig. 197 - right and

tighten it as much as possible. For tightening, we recommend that you use for

example the wheel wrench, the lashing eye of another vehicle or a similar ob-

ject which you can push through the eye.

–

Put the cover in place after screwing out the towing eye again and press into

place. The cover must engage firmly.

CAUTION

The towing eye must always be screwed in fully and firmly tightened, otherwise

the towing eye can tear when towing in or tow-starting!



Fuses and light bulbs 229

Fuses and light bulbs

Electric fuses

Colour coding of fuses

Colour

light brown

brown

red

Maximum amperage

Replacing fuses in the dash panel

5

7,5

10

Defect fuses must be replaced.

blue

15

yellow

white

green

orange

red

20

25

30

40

50

CAUTION

Fig. 198 Fuse cover: left side of the

dash panel

●

Never attempt to “repair” fuses and also do not replace them with a fuse of a

higher amperage - risk of fire! This may also cause damage at another part of the

electrical system.

Individual electrical circuits are protected by fuses. The fuses are located on the

left side of the dash panel behind the safety cover and under the cover in the en-

gine compartment on the left.

●

Have the electrical system checked as quickly as possible by a specialist ga-



rage if a newly inserted fuse blows again after a short time.

–

Switch the ignition off and also the electrical component affected.

Use a screwdriver to take off the fuse cover on the side of the dash panel

⇒ꢀfig. 198 or the fuse cover in the engine compartment ⇒ꢀfig. 199.

Find out which fuse belongs to the relevant component ⇒ꢀpage 232, Fuse as-

signment in the dash panel, ⇒ꢀpage 230, Fuse assignment in engine compart-

ment - version 1 or ⇒ꢀpage 231, Fuse assignment in engine compartment - ver-

sion 2.

Fuse cover in engine compartment

The fuse box in the engine compartment exists in two different

versions. You can determine which version your vehicle is fitted

with after removing the fuse cover at the location of the fuses.

–

Take the plastic clip out of its fixture in the fuse cover, insert it onto the re-

spective fuse and pull out this fuse.

Defect fuses can be detected by their melted metal strips. Replace the defect

fuse by a new fuse of the same ampere number.

Fit on the fuse cover again.

We recommend that you always have the small box of replacement fuses in your

vehicle. You can obtain replacement fuses from the range of ŠKODA Original Parts

or from a specialist garage.

Fig. 199 Fuse cover in engine compart-

ment

£

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

230 Fuses and light bulbs

On some vehicles, the battery cover must be removed before removing the fuse

cover ⇒ꢀpage 206.

No.

F5

Power consumer

Horn

Removing fuse cover

F6

Not assigned

A

–

Move the circlips

⇒ꢀfig. 199 as far as the stop, the symbol  appears behind

F7

Not assigned

the circlip and remove the cover.

F8

Not assigned

F9

Valves

Installing fuse cover

F10

F11

Not assigned

A

–

Position the fuse cover on the fuse box and push the circlips

stop - the symbol  is visible behind the circlip.

as far as the

Lambda probe

F12

F13

F14

F15

F16

F17

F18

F19

F20

F21

F22

F23

F24

F25

F26

F27

F28

F29

F30

F31

F32

F33

F34

F35

F36

Lambda probe

CAUTION

Control unit for automatic gearbox

●

When unlocking and locking the fuse cover, it must be pressed on the sides to

the box, otherwise damage can occur to the locking mechanism.

Not assigned

Coolant pump

●

Carefully position the fuse cover in the engine compartment. If the cover was

not correctly positioned, water can get into the fuses and this results in a damage

to the vehicle!

Not assigned



Instrument cluster, windshield wiper lever and turn signal light lever

Audio amplifier (sound system)

Radio

Fuse assignment in engine compartment - version 1

Phone

Not assigned

Engine control unit

Control unit for CAN databus

Not assigned

Fig. 200 Schematic representation of

fuse box in engine compartment - ver-

sion 1

Fuel dosage valve

Engine control unit

Main relay

Certain electrical components are only standard on certain vehicle model versions

or only suppliable as optional equipment for certain models.

Control unit for auxiliary heating

Front window wiper

Not assigned

No.

F1

Power consumer

Front right main headlight, right rear light unit

Valves for ABS

Not assigned

F2

F3

F4

Not assigned

£

Not assigned

Fuses and light bulbs 231

Certain electrical components are only standard on certain vehicle model versions

or only suppliable as optional equipment for certain models.

No.

F37

F38

F39

F40

F41

Power consumer

Not assigned

No.

F1

Power consumer

Radiator fan, valves

Not assigned

F2

Control unit for automatic gearbox DQ200

Measuring circuit

Not assigned

F3

Not assigned

F4

Valves for ABS

F42

F43

F44

F45

F46

F47

F48

F49

F50

F51

Not assigned

F5

Control unit for automatic gearbox DQ250

Instrument cluster, windshield wiper lever and turn signal light lever

Power supply for terminal 15 (ignition on)

Radio

Ignition

F6

Not assigned

F7

Not assigned

F8

F9

F10

F11

F12

F13

F14

F15

Not assigned

Front left main headlight, left rear light unit

Pump for ABS

Engine control unit, Main relay

Control unit for auxiliary heating

Control unit for CAN databus

Engine control unit

Power supply for terminal 15 (ignition on)

Not assigned

a)

Ignition

F52

F53

F54

Power supply relay - terminal X

Lambda probe (petrol engine)

Glow plug system relay and fuel pump (diesel engine)

Accessory equipment

Not assigned

F16

F17

F18

F19

F20

Front right main headlight, right rear light unit

Horn

a)

In order not to drain the battery unnecessarily when starting the engine, the electrical components

of this terminal are automatically switched off.



Audio amplifier (sound system)

Front window wiper

Fuse assignment in engine compartment - version 2

Valve for fuel dosing

water pump

F21

F22

F23

Lambda probe

Clutch pedal switch

Relay

Valves

High pressure pump

F24

F25

F26

F27

The radiator fan

Fig. 201 Schematic representation of

fuse box in engine compartment - ver-

sion 2

Pump for ABS

Left main headlight

Control unit for glow plug system

£

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

232 Fuses and light bulbs

No.

F28

F29

F30

Power consumer

No.

10

11

Power consumer

Windscreen heater

Adaptive left main headlight

Adaptive right main headlight

Not assigned

Accessory equipment

Power supply relay - terminal X

a)

12

13

Diagnostic socket, light switch, rain sensor, clock

Central locking system and bonnet lid

Central control unit - interior lights

The air conditioning system

Not assigned

a)

In order not to drain the battery unnecessarily when starting the engine, the electrical components

of this terminal are automatically switched off.



14

15

Fuse assignment in the dash panel

16

17

18

19

20

21

Not assigned

KESSY

KESSY ELV

22

23

24

25

26

Air blower for Climatronic

Front power window, central locking of the front doors

Selector lever lock, AQ250

Rear window heater, relay for auxiliary heating and ventilation

Power socket in the luggage compartment

Fig. 202 Schematic representation of

the fuse carrier in the dash panel

Certain electrical components are only standard on certain vehicle model versions

or only suppliable as optional equipment for certain models.

Fuel pump relay,

Fuel pump relay, control unit for fuel pump, injection valves

27

No.

Power consumer

28

29

30

31

Electric boot lid

Diagnostic socket, engine control unit, fuel pump relay, fuel pump con-

trol unit

AQ250

1

Ventilated front seats

Control unit for ABS, ESP, switch for tyre air pressure control, brake

sensor

DVD pre-installation

2

3

4

32

33

34

35

36

37

38

39

40

41

Front power window, central locking system of the rear doors

Electric sliding/tilting roof

Alarm, spare horn

Switch and control unit for airbag

WIV, parking light, dimming mirrors, pressure sensor, telephone prein-

stallation

front and rear lighter

Control unit for headlamp beam adjustment and headlight swivel, con-

trol unit for parking aid, control unit for park assist

5

6

Headlight cleaning system

Front seat heating

Instrument cluster, control unit for electromechanical power steering,

Haldex, selector lever lock, power supply for data bus, AQ250

Heated rear seats

7

8

9

Valve heating, air mass meter

Control unit for trailer detection

Relay for auxiliary heating

Rear window wiper

Fan air-conditioning system, relay for auxiliary heating and ventilation

Not assigned

£

Fuses and light bulbs 233

Change of bulbs on vehicles with Xenon lights (low beam lights, parking lights and

main beam lights) should be undertaken by a specialist garage.

No.

42

43

44

45

46

47

48

49

Power consumer

Light switch

Bulb - Overview

Control unit for trailer detection

Switch for seat heating

Not assigned

Front headlight

Low beam

Halogen headlight

Xenon headlight

D1S

H7

H3

Main beam

D1S, H3

Parking lights

Turn signals

Fog lights

W5W

PY 24W

H8

Preparation for the aftermarket radio

Not assigned

Electrically adjustable seats are protected by automatic circuit breakers, which

switch on again automatically after a few seconds after the overload has been

eliminated.

Rear light unit

Reversing light

Turn signals

Bulb

W16W

PY21W

W16W



Light bulb for the brake lights and tail

lights

Bulbs

Parking lights

Fog lights

W5W

P21W SLL

Changing bulbs

Others

Bulb

C5W

W5W

LED

The relevant lamp must always be switched off before a light bulb is replaced.

Licence plate light

front interior lighting

3. Brake light

Defect light bulbs should only be replaced with light bulbs of the same type. The

designation is located on the light socket or the glass bulb.

Changing certain bulbs is not something which you can do yourself, but requires

to be done by a specialist. Other parts of the vehicle must be removed in order to

change the light bulbs. This applies, in particular, to bulbs which can only be

reached from the engine compartment.

Rear interior lighting

W5W

C3W

Storage compartment light - front pas-

senger side

Luggage compartment light

Door warning light

Lighting for vanity mirror

Entry light

W5W

C5W

We therefore recommend that you have any bulbs changed by an authorised

ŠKODA Service Partner or, in exceptional cases, by calling on other professional

assistance.

Please note that the engine compartment is a hazardous area ⇒ꢀpage 198, Work-

£

W5W

ing in the engine compartment.

We recommend that you always have a small box of replacement bulbs in your ve-

hicle. You can obtain replacement bulbs from ŠKODA Original Accessories or from

a specialist garage.

A stowage place for the bulbs is located in the box in the spare wheel.

Fitted with a xenon headlight

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

234 Fuses and light bulbs

WARNING

Parking lights and main beam lights

●

Bulbs H7 and H3 are pressurised and may burst when changing the bulb -

risk of injury!

●

It is recommended to wear gloves and safety glasses when changing a

bulb.

●

Gas discharge bulbs (xenon bulbs) operate with a high voltage, professio-

nal knowledge is required - danger to life!

CAUTION

Fig. 204 Removing the bulbs for the

parking and main beam light

Do not take hold of the glass bulb with naked fingers (even the smallest amount

of dirt reduces the working life of the light bulb). Use a clean cloth, serviette or

something similar.

Removing the light bulb for the parking light

Note

–

Switch the ignition and all lights off.

This Owner's Manual only describes the replacement of bulbs where it is assumed

that no major complications will arise. Other light bulbs should be changed by your

specialist garage.

Open the bonnet.

A

Remove the protective cap

A

⇒ꢀfig. 203.



Remove the socket

⇒ꢀfig. 204.

Front headlight

Take the faulty bulb out of the fixture and insert a new one.

Removing the light bulb for the main beam light

–

Switch the ignition and all lights off.

Open the bonnet.

A

Remove the protective cap

⇒ꢀfig. 203.

B

Press the sprung wire clamps

side.

⇒ꢀfig. 204 together and hang them to the

C

–

Remove the socket

⇒ꢀfig. 204.

Fig. 203 Front headlight: Fitting posi-

tion of the bulbs

Take the faulty bulb out of the fixture and insert a new one.

Positions of the light bulbs in the front headlight ⇒ꢀfig. 203.

Installation is carried out in the reverse order.

A

B

C

Parking lights and main beam lights

Low beam

Turn signal light (at the front)

Note

We recommend that you have the headlight setting checked by a Skoda Service

Partner after replacing the light bulb.



Fuses and light bulbs 235

Low beam light

Fog lights

Fig. 205 Removing the light bulb for the

low beam light

Fig. 206 Front bumper: Cover/fog lights with daylight driving lights

Replacing bulbs

–

Switch the ignition and all lights off.

Open the bonnet.

B

–

Switch the ignition and all lights off.

Remove the protective cap

⇒ꢀfig. 203.

–

Grasp the cover at the points marked with the arrows ⇒ꢀfig. 206 - left and take

Turn the connector with the light bulb up to the stop towards the left and re-

move ⇒ꢀfig. 205.

Replace the lamp, insert the connector with the new lamp and turn to the

right up to the stop.

it out.

–

Guide your hand into the opening, in which the cover was located, and press

C

–

the spring bolt

⇒ꢀfig. 206.

–

Take out the fog light.

Insert the protective cap.

A

B

Turn the socket

out.

or

with the bulb to the left up to the stop and take it

Note

–

Replace the lamp, insert the connector with the new lamp and turn to the

right up to the stop.

We recommend that you have the headlight setting checked by a Skoda Service

Partner after replacing the light bulb.



For the installation, first of all insert the fog light with the interlock to the side

far away from the marking of the vehicle.

Press into place the headlight onto the side facing the marking. The spring

bolt must engage firmly.

In order to reinstall the cover, first of all insert one part of the cover starting

on the side facing the fog light. Then press the cover closed on the side facing

the marking. The cover must engage firmly.

A

- bulb for daylight driving lights.

- bulb for fog lights.



B

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

236 Fuses and light bulbs

Rear light unit

–

To re-insert the lamp holder, guide it into the housing of the rear light unit.

Press onto the spring bolt until it is heard to lock.

Guide the cover of the rear light unit into the inner side of the bonnet lid.

CAUTION

When removing and installing the rear light unit make sure not to damage the

paintwork of the vehicle and the rear light unit.



Changing light bulbs in the rear light unit

Fig. 207 Remove the outer part of the rear light unit/remove the inner part of the rear light

unit

Remove and install the outer part of the rear light unit

–

Switch the ignition and all lights off.

Open the boot lid/luggage compartment door.

Take out the plugs ⇒ꢀfig. 207 - left and unscrew the rear light unit using a torx

1)

wrench .

–

Carefully take out the lamp. Do not pull the grommet with the cables out of

the body.

Fig. 208 Outer part of the rear light unit: Bulbs/inner part of the rear light unit: Lamps

Change bulbs in the outer part of the rear light unit

A

To re-insert the rear light unit, first of all guide it with the support

⇒ꢀfig. 208 towards the front onto a bolt on the bodywork.

–

To change a bulb, turn its fixture to the left up to the top and take it out.

–

Carefully press the rear light unit into the bodywork.

–

Change the bulb, insert again the fixture with the bulb into the housing and

turn it to the right up to the stop.

Screw the rear light unit tight and press in the plugs ⇒ꢀfig. 207 - left.

Change bulbs in the inner part of the rear light unit

Remove and install the inner part of the rear light unit

4

–

To change a bulb of the reversing light

out of the fixture and insert a new one.

⇒ꢀfig. 208, pull the defective bulb

–

Switch the ignition and all lights off.

Open the boot lid/luggage compartment door.

5

To change the bulb of the rear fog light

to the left up to the stop and take it out.

⇒ꢀfig. 208, turn the defective bulb

Take off the cover of the rear light unit on the inner side of the bonnet lid

⇒ꢀfig. 207 - right.

Press a new light bulb into the socket and turn the light bulb to the right as far

as the stop.

–

Press the spring bolt ⇒ꢀfig. 207 - right and take the lamp holder out of the

housing of the rear light unit.

£

Fitting position of the bulbs in the outer rear light unit ⇒ꢀfig. 208 - left.

1)

The torx wrench is located in the vehicle toolkit box.

Fuses and light bulbs 237

1

3

5

- Turn signal lights

- Parking lights/Brake light

- parking lights

Changing bulbs

,

and

in the rear light unit

–

Turn the socket with the bulb to the left up to the stop and take it out of its

housing.

2

3

Remove the defective bulb from the socket and insert a new bulb into the

socket.

Fitting position of the bulbs in the inner rear light unit ⇒ꢀfig. 208 - right.

4

Insert the socket with the new bulb into the housing and turn it to the right up

to the stop.

- Reversing light



5

- Rear fog light

2

4

Changing bulbs

and

in the rear light unit

–

Turn the socket with the bulb to the left up to the stop and take it out of its

housing.

Rear light unit (Combi)

–

Press in the defective bulb, turn it to the left up to the stop and take it out.

Insert a new bulb into the socket, press it in and turn the bulb to the right up

to the stop.

–

Insert the socket with the new bulb into the housing and turn it to the right up

to the stop.

Fitting position of the bulbs ⇒ꢀfig. 209.

1

- Parking lights/Reversing light

2

3

4

5

- Reversing light

Fig. 209 Remove rear light unit (Combi)

- Turn signal lights

Removing and installing the rear light unit

- Parking lights/Brake light

- parking lights

–

Switch the ignition and all lights off.

Open the boot lid/luggage compartment door.

CAUTION

Take out the plugs ⇒ꢀfig. 209 - left and unscrew the rear light unit using a torx

1)

wrench .

When removing and installing the rear light unit make sure not to damage the

paintwork of the vehicle and the rear light unit.



–

Carefully take out the lamp. Do not pull the grommet with the cables out of

the body.

A

When re-installing, first insert the rear light unit with the openings

the studs in the body.

onto

–

Press the rear light unit down into the body until it is heard to lock in place.

Screw the rear light unit tight and press in the plugs.

1)

The torx wrench is located in the vehicle toolkit box.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical data

238 Fuses and light bulbs

Licence plate light

–

Replace the the glass cover of the light and press it down to the stop - ensure

that the glass cover is correctly installed.



Fig. 210 Rear bumper: Licence plate

light

–

Unscrew the glass cover of the light ⇒ꢀfig. 210.

Take the defective bulb out of the holder and insert a new one.

Replace the the glass cover of the light and press it down to the stop - ensure

that the glass cover is correctly installed.



–

Screw the glass cover tight.

Licence plate light (Combi)

Fig. 211 Luggage compartment door Li-

cence plate light

–

Insert a flat screwdriver into the opening at the point of the arrow ⇒ꢀfig. 211

and carefully press towards the centre of the lamp, by doing so the lamp

slightly jumps out.

–

Take out the lamp.

Take the defective bulb out of the holder and insert a new one.

Breakdown assistance for Your Skoda Superb SUV Second Generation (2009-2015)

Related Topics

Popular Owner Manuals

Latest Owner Manuals