Get Wheels -> Tyre pressure monitoring system Guide for Skoda Superb SUV Third Generation (2016-2023)

Wheels › Tyre pressure monitoring system 209

Warning when pressure changes

Stop the vehicle, switch oﬀ the ignition and start

the engine.

›

illuminates

Stop the vehicle.

Check the tyres and tyre pressures.

If the symbol ﬂashes again after starting the en-

gine, there is a system fault.

Continue driving, exercising appropriate caution,

and seek the help of a specialist garage.

›

Show tyres with changed pressure

In the following menu, select the menu item for

displaying the tyre condition.

›

Tyre pressure monitoring system

Functionality

Or:

The system measures tyre pressure while driving us-

ing sensors on the wheels.

Functional restriction

For correct system function, you must select the

tyre type as well as the load condition of the vehicle

in the Infotainment.

The system is unable to provide a warning in the

event of a very rapid tyre pressure loss, e.g. sudden

puncture.

After switching on the ignition, the last measured

tyre pressure values are displayed. This display will

be updated at the start of the journey.

The system function may be restricted in the follow-

ing cases.

Warning when changing the tyre pressure

Uneven loading of the wheels, e.g. with a trailer at-

tached.

▶

illuminates

Stop the vehicle.

Check the tyres and tyre pressures.

Sports driving style.

Driving on unpaved roads.

Fitted snow chains.

›

▶

›

Overview

Save tyre pressure values

Display in the instrument cluster

Save tyre pressure values in Infotainment

Select Vehicle

›

Inﬂate the tyres to the stipulated inﬂation pressure.

Turn on the ignition.

In the following menu, select the menu item for

displaying the vehicle condition.

›

Display in Infotainment

›

In the following menu, select the menu item for

displaying the vehicle condition.

›

Or:

Using the functional surfaces

Pressure Monitoring menu item.

choose the Tyre

›

Using the functional areas

the tyre control display.

Tap the functional surface

select the menu for

›

Instrument cluster / Infotainment

›

Then follow the instructions on the screen.

Save the tyre pressure values in the following cases.

Change in tyre pressure.

Change of one or more wheels.

Change of position of a wheel on the vehicle.

Always after covering a distance of 10,000 km or

once a year.

▶

Troubleshooting

Tyre pressure

Tyre pressure display faulty

Recommended tyre pressure

Tyre pressure not available

ﬂashes for about 1 minute and stays on

210 Wheels › Wheel bolt cover caps

Pull oﬀ

Tyre pressure too low

Push the pull-oﬀ clamp onto the cover cap up to

›

Setting the vehicle's load condition

the stop.

Pull oﬀ the cover cap.

›

The tyres warm up while driving and there is an

increase in pressure. This is completely normal, it is

not a defect. If the system shows an increase in

pressure while driving, do not reduce the pressure.

Install

Push the cover cap onto the wheel bolt to the stop.

›

Full wheel frame

Settings

Pull oﬀ panel and install

Tyre type

Select the tyre type in the following menu.

Applies to factory installed covers or covers deliv-

ered with ŠKODA original accessories.

Or:

Remove

Hang the bracket for pulling oﬀ the wheel covers

at the edge of one of the openings in the cover.

›

Vehicle loading condition

Push the wheel wrench through the bracket, sup-

port it on the tire and pull oﬀ the cover.

›

In the following menu, select the menu item for

›

displaying the vehicle condition.

Install

Place the cover on the intended valve section on

the rim.

›

Or:

If an anti-theft wheel bolt is used, it must be in the

position marked on the cover.

Press the trim, starting at the valve, into the rim on

both sides until it engages around the entire cir-

cumference.

Using the functional surfaces

Pressure Monitoring menu item.

choose the Tyre

›

Tap the

functional area and select the vehicle

load condition.

NOTICE

Use hand pressure, do not hit the wheel cover.

▶

Troubleshooting

Functional restriction / system fault

Pull oﬀ and install the aero cover

ﬂashing

Applies to factory installed covers or covers deliv-

ered with ŠKODA original accessories.

Stop the engine and start again.

If the indicator light ﬂashes again after the engine

starts, there is a problem with the system.

Continue driving, exercising appropriate caution,

›

Remove

›

and seek the help of a specialist garage.

Wheel bolt cover caps

Pull oﬀ and install cover caps

Hook the bracket to remove the wheel covers at

the edge of the panel as close to the centre as pos-

sible.

›

Loosen the centre of the wheel cover by pulling

and pull oﬀ the cover.

›

To make removal easier, it is possible to insert the

wheel wrench through the bracket loop and pull on

the two key ends.

Wheels -> Tyre pressure monitoring system for Your Skoda Superb SUV Third Generation (2016-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals