Get Audio -> Type A and B audio set Guide for Subaru Outback SUV Second Generation (2000-2004)

5-6

Type A and B audio set (if equipped)

Type A: Without weather band

Type B: With weather band

The audio set will operate only when the ignition switch is in the “ACC” or

“ON” position.

Radio operation

HB5052BB

1 Power switch/Volume, Tone,

Balance, Fader control dial

2 BAND button

3 Tuning buttons

4 Preset buttons

5 AUDIO button

6 SCAN button

B Power switch and volume/bass/treble/fader/balance control

n Power switch and volume control (PWR/VOL)

The dial 1 is used for both power (ON/OFF) and volume control. The

radio is turned ON and OFF by pushing the dial and the volume is

controlled by turning the dial.

Audio

5-7

– CONTINUED –

n Tone and balance control (AUDIO)

The volume control dial 1 normally functions as a volume control.

This dial becomes a control for Bass, Treble, Fader or Balance when

you select the appropriate tone and balance control mode.

Choose desired volume level for each mode by turning the volume

control dial. The control function returns to volume control mode after

about 5 seconds.

To change control modes: Each brief press of the “AUDIO” button

5 changes control modes in the following sequence starting from vol-

ume control mode. (When the radio is first turned on, the control mode

is in the volume control.)

Volume Bass Treble Balance Fader

(VOL) (BAS) (TRE) (BAL) (FAD)

The “AUDIO” button 5 is used for selecting the following control

modes:

Display

Control mode

HB5036BA

Turn counterclockwise Turn clockwise

BAS Bass control For less bass For more bass

TRE Treble control For less treble For more treble

FAD Fader control To increase rear speaker

volume and decrease front

speaker volume

To increase front speaker

volume and decrease rear

speaker volume

BAL Balance control To increase left speaker

volume and decrease right

speaker volume

To increase right speaker

volume and decrease left

speaker volume

VOL Volume control For less volume For more volume

5-8

B Waveband selection

n FM/AM selection

Push the “BAND” button 2 to select FM1, FM2 or AM reception. The

display indicates which one is currently selected.

n FM/AM/Weather band selection

Push the “BAND” button 2 to select FM1, FM2, AM or Weather band

(WB) reception. The display indicates which is currently selected.

B Stereo indicator

The stereo indicator “ST” will come on when an FM stereo broadcast

is received.

B Tuning (TUNE)

n Manual tuning (TUNE)

Press the tuning button 3 marked “Y” to increase the tuning frequen-

cy and press the tuning button marked “B” to decrease it.

Each time the button is pressed, the frequency interval can be

changed between 10 kHz in the AM mode and 0.2 MHz in the FM

mode.

Constant pressure on the button causes a continuous change in the

frequency.

n Manual tuning for weather band

When weather band mode is selected, press the tuning button

marked “Y” to change the WB channel up and press the tuning but-

ton marked “B” to change the WB channel down. Each time the but-

ton is pressed, the WB channel changes to the next channel.

Constant pressure on the button causes a continuous change in the

frequency.

n Automatic tuning (SCAN)

Press the “SCAN” button

6 to change the radio to the SCAN mode. In

this mode, the radio scans through the radio band until a station is

found. The radio will stop at the station for five seconds while display-

ing the frequency, after which scanning will continue until the entire

band has been scanned from the low end to the high end.

Audio

5-9

– CONTINUED –

Press the “SCAN” button again to cancel the SCAN mode and to stop

on any displayed frequency.

When the “SCAN” button is pressed for automatic tuning, stations are

scanned in the direction of low frequencies to high frequencies only.

Automatic tuning may not function properly if the station reception is

weakened by distance from the station or proximity to tall buildings

and hills.

B Selecting preset stations

Presetting a station with a “preset button”

4 allows you to select that

station in a single operation. Up to six WB (if equipped), AM, FM1 and

FM2 stations each may be preset.

B How to preset stations

1. Press the “BAND” button 2 to select FM1, FM2, AM or WB (if

equipped) reception.

2. Press the “SCAN” button or tune the radio manually until the

desired station frequency is displayed.

3. Press one of the preset buttons for more than 2 seconds to store

the frequency. At this time, there will momentarily be no sound from

the radio. If the button is pressed for less than 2 seconds, the preced-

ing selection will remain in memory.

NOTE

If the connection between the radio and battery is broken for any

reason such as vehicle maintenance or radio removal, all stations

stored in the preset buttons are cleared. If this occurs, it is neces-

sary to reset the preset buttons.

5-10

Compact disc player operation

HB5052CB

7 Disc slot

8 CD button

9 Eject button

Q Fast forward and track up

button

W Fast reverse and track down

button

E Random button

R Repeat button

T Scan button

Y PWR (power) switch

B To playback a compact disc

n When CD is not in the player

Hold a disc with a finger in the center hole while gripping the edge of

the disc, then insert it in to the slot (with the label side up) and the

player will automatically pull the disc into position.

A 8 cm/3 inch CD may also be used without any adapter.

NOTE

D DO NOT INSERT TWO DISCS INTO THE DISC INSERTION

SLOT AT A TIME.

D Be sure to always insert a disc with the label side up. If a disc

is inserted with the label side down, it might be ejected or the

player might shut off.

D After the last song finishes, the player will automatically return

to track 1 (the first song on the disc).

Audio

5-11

– CONTINUED –

n When CD is in the player

When the “CD” button 8 is pressed, the player will start playback.

NOTE

After the last song finishes, the player will automatically return to

track 1 (the first song on the disc).

B To stop playback of a CD

When the “PWR” button Y is pressed during playback of a CD, the

CD stops playing temporarily. To let the CD resume playing, press the

button again.

B To select a song from its beginning

n Forward direction

Briefly press the “Y” button Q to skip to the beginning of the next

track. Each time the button is pressed, the indicated track number will

increase.

n Backward direction

Briefly press the “B” button W to skip to the beginning of the current

track. Each time the button is pressed, the indicated truck number will

decrease.

B Fast forwarding and fast reverse

n Fast forward

Press the “Y” button Q continuously for more than 0.5 second to fast

forward the disc.

Release the button to stop fast forwarding.

n Fast reverse

Press the “B” button

W continuously for more than 0.5 second to fast

reverse the disc.

Release the button to stop fast reverse.

B Repeat playback

Use this to play a certain track repeatedly. During playback, press the

“RPT” button

R and release it in less than 2 seconds. The “RPT” indi-

cator will come on and the song will be played continuously. To can-

5-12

cel the repeat mode, press the button again. Then the “RPT” indicator

goes out, and normal playback mode is restored.

B Random playback

Use this to play the tracks on the disc in random order. During play-

back, press the “RDM” button

E and hold it in for more than 2 se-

conds. The “RDM” indicator will come on and all songs on the disc

will be played in a random order.

To cancel the random mode, press the button again. Then the “RDM”

indicator goes out, and normal playback mode is restored.

B Scan

Press the “SCAN” button

T and release it in less than 2 seconds, and

you can hear the first 10 seconds of each track to seach for the

desired program. To continue listening to the program, press the

“SCAN” button again. After all tracks on the disc has been scanned,

normal playback mode is restored.

B To eject a disc from the player

When a disc is being played back or when a disc is in the player,

press the eject button “

” 9. The disc will be ejected.

The disc may be removed even when the ignition switch is in the

“LOCK” position.

NOTE

D Avoid driving the vehicle with a CD sticking out, because

vibration might make it fall out.

D To protect the disc, the disc is automatically loaded if it is left

in the ejected position for more than approximately 15 seconds

(Auto Reload). In this case, the disc is not played.

Audio -> Type A and B audio set for Your Subaru Outback SUV Second Generation (2000-2004)

Related Topics

Popular Owner Manuals

Latest Owner Manuals