2005-2009 Subaru Outback SUV Interior equipment -> Cargo area cover (Station wagon) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Interior equipment -> Cargo area cover (Station wagon) for Your Subaru Outback SUV Third Generation (2005-2009)

Black plate (232,1)
北米Model "A2420BE-B" EDITED: 2006/ 7/ 26
6-12 Interior equipment
Floor mat
A retaining pin is located on the driver’s
side of the vehicle next to the fuel filler
door release. Fit the grommet in the carpet
onto the pin to prevent the carpet from
moving.
CAUTION
Make sure the driver’s floor mat is
placed back in its proper location
and correctly secured on its retain-
ing pin. If the floor mat slips forward
and interferes with the movement of
the pedals during driving, it could
cause an accident.
Cargo area cover (Station
wagon)
The cargo area cover is provided for
covering the cargo area and to protect its
contents from direct sunlight. This cover is
detachable to make room for additional
cargo.
& Using the cover
To extend the cover, pull the end of the
cover out of the housing, then insert its
hooks into the catche s as shown. To
rewind it, unhook it from the catches and
it will rewind automatically. You should
hold on to the cover and guide it back into
the cover housing while it is rewinding.
Black plate (233,1)
北米Model "A2420BE-B" EDITED: 2006/ 7/ 26
WARNING
Do not place anything on the ex-
tended cover. Putting excessive
weight on the extended cover can
break it and an object on the cover
could tumble forward in the event of
a sudden stop or collision. This
could cause serious injury.
& To remove the cover housing
1. Rewind the cover.
2. Hold down the button on the right-
hand rear quarter panel and lift up the
right-hand cover housing.
3. Remove the cover housing.
& To remove the rear gate
board
1. Remove the top of the rear gate board
from the groove in the rear gate panel.
2. Hold both sides of the bottom edge of
the rear gate board, rotate the rear gate
board toward you, and pull it out down-
ward.
& Stowage of the cargo area
cover and rear gate board
The cargo area cover and rear gate board
can be stowed in under the cargo floor.
1. To open the lid, pull the handle up.
Interior equipment 6-13
– CONTINUED –
6
Black plate (234,1)
北米Model "A2420BE-B" EDITED: 2006/ 7/ 26
6-14 Interior equipment
2. To keep the lid open, hang the hook
(provided on the back of the lid) on the
rear edge of the roof.
3. Remove the left and right parts of the
cargo floor lid.
4. Stow the cover housing and rear gate
board in the cargo area end.
& To install the cover housing
To install the cover housing, insert both
ends of the cover housing into the
retainers.
Black plate (235,1)
北米Model "A2420BE-B" EDITED: 2006/ 7/ 26
& To install the rear gate board
Insert (tipped at an angle) the hooks on
the rear gate board into the holes in the
rear gate panel.
Rotate the rear gate board toward you
until its top touches the rear gate panel.
Fit the top of the rear gate board into the
groove in the rear gate panel.
Stowage boxes (Station wa-
gon)
A stowage box is located on each side of
the cargo area. You can access each one
by pushing up and pulling the knob on the
lid.
Interior equipment 6-15
6

Related Topics

Interior equipment
Interior light Sun visors Storage compartment Cup holder Accessory power outlets Coat hook Shopping bag hook Floor mat Stowage boxes (Station wagon) Convenient tie-down hooks (if equipped) Under-floor storage compartment HomeLink Wireless Control System (if equipped)

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot