Get Seat, seatbelt and SRS airbags -> Fastening the seatbelt Guide for Subaru Outback SUV Fourth Generation (2010-2014)

1-16 Seat, seatbelt and SRS airbags

When securing a child restraint system on

the rear seats by using a seatbelt, the

seatbelt must be changed over to the

Automatic Locking Retractor (ALR) mode.

For instructions on how to install the child

restraint system using a seatbelt, refer to

“Installing child restraint systems with A/

ELR seatbelt” F 1-28.

When the child restraint system is re-

moved, make sure that the retractor is

restored to the Emergency Locking Re-

tractor (ELR) mode by allowing the seat-

belt to retract fully.

& Seatbelt warning light

and chime

R ef er to “Seatbelt w arning light and

chime” F3-13.

& Fastening the seatbelt

WARNING

. Never use a belt that is twisted or

reversed. In an accident, this can

increase the risk or severity of

injury.

. Keep the lap belt as low as

possible on your hips. In a colli-

sion, this spreads the force of the

lap belt over stronger hip bones

instead of across the weaker

abdomen.

. Seatbelts provide maximum re-

straint when the occupant sits

well back and upright in the seat.

To reduce the risk of sliding

under the seatbelt in a collision,

the front seatbacks should be

always used in the upright posi-

tion while the vehicle is running.

If the front seatbacks are not

used in the upright position in a

collision, the risk of sliding under

the lap belt and of the lap belt

sliding up over the abdomen will

increase, and both can result in

serious internal injury or death.

. Do not put cushions or any other

materials between occupants

and seatbacks or seat cushions.

If you do so, the risk of sliding

under the lap belt and of the lap

belt sliding up over the abdomen

will increase, and both can result

in serious internal injury or

death.

WARNING

Never place the shoulder belt under

the arm or behind the back. If an

accident occurs, this can increase

the risk or severity of injury.

CAUTION

Metallic parts of the seatbelt can

become very hot in a vehicle that

has been closed up in sunny weath-

er; they could burn an occupant. Do

not touch such hot parts until they

cool.

! Front seatbelts

1. Adjust the seat position:

Driver’s seat: Adjust the seatback to the

upright position. Move the seat as far from

the steering wheel as practical while still

maintaining full vehicle control.

Front passenger’s seat: Adjust the seat-

back to the upright position. Move the seat

as far back as possible.

2. Sit well back in the seat.

3. Pick up the tongue plate and pull the

belt out slowly. Do not let it get twisted. If

the belt stops before reaching the buckle,

return the belt slightly and pull it out more

slowly. If the belt still cannot be unlocked,

let the belt retract slightly after giving it a

strong pull, then pull it out slowly again.

4. Insert the tongue plate into the buckle

until you hear a click.

5. To make the lap part tight, pull up on

the shoulder belt.

6. Place the lap belt as low as possible

on your hips, not on your waist.

! Adjusting the front seat shoulder

belt anchor height

The shoulder belt anchor height should be

adjusted to the position best suited for the

driver/front passenger. Always adjust the

anchor height so that the shoulder belt

passes over the middle of the shoulder

without touching the neck.

To raise:

Slide the anchor up.

To lower:

Push the release button and slide the

anchor down.

Pull down the anchor to make sure that it

is locked in place.

Seat, seatbelt and SRS airbags 1-17

– CONTINUED –

1-18 Seat, seatbelt and SRS airbags

WARNING

When wearing the seatbelts, make

sure the shoulder portion of the

webbing does not pass over your

neck. If it does, adjust the seatbelt

anchor to a lower position. Placing

the shoulder belt over the neck may

result in neck injury during sudden

braking or in a collision.

! Unfastening the seatbelt

Push the button on the buckle.

Before closing the door, make sure that

the belts are retracted properly to avoid

catching the belt webbing in the door.

! Rear seatbelts (except rear center

seatbelt on Outback)

1. Sit well back in the seat.

2. Pick up the tongue plate and pull the

belt out slowly. Do not let it get twisted. If

the belt stops before reaching the buckle,

return the belt slightly and pull it out more

slowly. If the belt still cannot be unlocked,

let the belt retract slightly after giving a

strong pull on it, then pull it out slowly

again.

3. Insert the tongue plate into the buckle

until you hear a click.

4. To make the lap part tight, pull up on

the shoulder belt.

5. Place the lap belt as low as possible

on your hips, not on your waist.

! Unfastening the seatbelt

Push the button on the buckle.

Before closing the door, make sure that

the belts are retracted properly to avoid

catching the belt webbing in the door.

! Rear center seatbelt on Outback

1) Center seatbelt tongue plate

2) Connector (tongue)

3) Connector (buckle)

4) Center seatbelt buckle

WARNING

Fastening the seatbelt with the web-

bing twisted can increase the risk or

severity of injury in an accident.

When fastening the belt after it is

pulled out from the retractor, espe-

cially when inserting the connec-

tor’s tongue plate into the mating

buckle (on right-hand side), always

check that the webbing is not

twisted.

WARNING

Be sure to fasten both tongue plates

to the respective buckle s. If the

seatbelt is used only as a shoulder

belt (with the connector’s tongue

plate not fastened to the connec-

tor’s buckle on the right-hand side),

it cannot properly restrain the wear-

er in position in an accident, possi-

bly resulting in serious injury or

death.

Seat, seatbelt and SRS airbags 1-19

– CONTINUED –

1-20 Seat, seatbelt and SRS airbags

Rear center seatbelt is stowed in the

recess of the ceiling.

1. Retrieve the connector (tongue) plate

from the slot in the recess by pulling the

connector (tongue) plate.

2. Pull out the seatbelt slowly from the

retractor.

3. After confirming that the webbing is not

twisted, insert the connector (tongue)

attached at the webbin g end into the

buckle on the right-hand side until a click

is heard. If the belt stops before reaching

the buckle, return the belt slightly and pull

it out more slowly. If the belt still cannot be

unlocked, let the belt retract slightly after

giving it a strong pull, then pull it out slowly

again.

4. After fastening the seatbelt, make sure

that the “

” m ark on the connector

(tongue) and the “

” mark on the buckle

face outwards.

5. Insert the center seatbelt tongue plate

into the center seatbelt buckle marked

“CENTER” on the left-hand side until it

clicks.

6. To make the lap part tight, pull up on

the shoulder belt. And place the lap belt as

low as possible on your hips, not on your

waist.

! Unfastening the seatbelt

Push the release button of the center

seatbelt buckle (on the left-hand side) to

unfasten the seatbelt.

1. Insert a key or other hard pointed

object into the slot in the connector

(buckle) on the right-hand side and push

it in, and the connector (tongue) plate will

disconnect from the buckle.

Seat, seatbelt and SRS airbags 1-21

– CONTINUED –

1-22 Seat, seatbelt and SRS airbags

2. Allow the retractor to roll up the belt.

You should hold the webbing end and

guide it back into the retractor while it is

rolling up. Neatly store the tongue plate in

the recess and then insert the connector

(tongue) plate into the slot.

CAUTION

. Do not allow the retractor to roll

up the seatbelt too quickly.

Otherwise, the metal tongue

plates may hit against the trim,

resulting in damaged trim.

. Have the seatbelt fully rolled up

so that the tongue plates are

neatly stored. A hanging tongue

plate can swing and hit against

the trim during driving, causing

damage to the trim.

& Seatbelt maintenance

To clean the seatbelts, use a mild soap

and lukewarm water. Never bleach or dye

the belts because this could seriously

affect their strength.

Inspect the seatbelts and attachments

including the webbing and all hardware

periodically for cracks, cuts, gashes,

tears, damage, loose bolts or worn areas.

Replace the seatbelts even if only minor

damage is found.

CAUTION

. Keep the belts free of polishes,

oils, chemicals and particularly

battery acid.

. Never attempt to make modifica-

tions or changes that will prevent

the seatbelt from operating prop-

erly.

Seat, seatbelt and SRS airbags -> Fastening the seatbelt for Your Subaru Outback SUV Fourth Generation (2010-2014)

Related Topics

Popular Owner Manuals

Latest Owner Manuals